| /* |
| * i82365.h 1.15 1999/10/25 20:03:34 |
| * |
| * The contents of this file may be used under the |
| * terms of the GNU General Public License version 2 (the "GPL"). |
| * |
| * Software distributed under the License is distributed on an "AS IS" |
| * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See |
| * the License for the specific language governing rights and |
| * limitations under the License. |
| * |
| * The initial developer of the original code is David A. Hinds |
| * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds |
| * are Copyright (C) 1999 David A. Hinds. All Rights Reserved. |
| */ |
| |
| FILE_LICENCE ( GPL2_ONLY ); |
| |
| #ifndef _LINUX_I82365_H |
| #define _LINUX_I82365_H |
| |
| /* register definitions for the Intel 82365SL PCMCIA controller */ |
| |
| /* Offsets for PCIC registers */ |
| #define I365_IDENT 0x00 /* Identification and revision */ |
| #define I365_STATUS 0x01 /* Interface status */ |
| #define I365_POWER 0x02 /* Power and RESETDRV control */ |
| #define I365_INTCTL 0x03 /* Interrupt and general control */ |
| #define I365_CSC 0x04 /* Card status change */ |
| #define I365_CSCINT 0x05 /* Card status change interrupt control */ |
| #define I365_ADDRWIN 0x06 /* Address window enable */ |
| #define I365_IOCTL 0x07 /* I/O control */ |
| #define I365_GENCTL 0x16 /* Card detect and general control */ |
| #define I365_GBLCTL 0x1E /* Global control register */ |
| |
| /* Offsets for I/O and memory window registers */ |
| #define I365_IO(map) (0x08+((map)<<2)) |
| #define I365_MEM(map) (0x10+((map)<<3)) |
| #define I365_W_START 0 |
| #define I365_W_STOP 2 |
| #define I365_W_OFF 4 |
| |
| /* Flags for I365_STATUS */ |
| #define I365_CS_BVD1 0x01 |
| #define I365_CS_STSCHG 0x01 |
| #define I365_CS_BVD2 0x02 |
| #define I365_CS_SPKR 0x02 |
| #define I365_CS_DETECT 0x0C |
| #define I365_CS_WRPROT 0x10 |
| #define I365_CS_READY 0x20 /* Inverted */ |
| #define I365_CS_POWERON 0x40 |
| #define I365_CS_GPI 0x80 |
| |
| /* Flags for I365_POWER */ |
| #define I365_PWR_OFF 0x00 /* Turn off the socket */ |
| #define I365_PWR_OUT 0x80 /* Output enable */ |
| #define I365_PWR_NORESET 0x40 /* Disable RESETDRV on resume */ |
| #define I365_PWR_AUTO 0x20 /* Auto pwr switch enable */ |
| #define I365_VCC_MASK 0x18 /* Mask for turning off Vcc */ |
| /* There are different layouts for B-step and DF-step chips: the B |
| step has independent Vpp1/Vpp2 control, and the DF step has only |
| Vpp1 control, plus 3V control */ |
| #define I365_VCC_5V 0x10 /* Vcc = 5.0v */ |
| #define I365_VCC_3V 0x18 /* Vcc = 3.3v */ |
| #define I365_VPP2_MASK 0x0c /* Mask for turning off Vpp2 */ |
| #define I365_VPP2_5V 0x04 /* Vpp2 = 5.0v */ |
| #define I365_VPP2_12V 0x08 /* Vpp2 = 12.0v */ |
| #define I365_VPP1_MASK 0x03 /* Mask for turning off Vpp1 */ |
| #define I365_VPP1_5V 0x01 /* Vpp2 = 5.0v */ |
| #define I365_VPP1_12V 0x02 /* Vpp2 = 12.0v */ |
| |
| /* Flags for I365_INTCTL */ |
| #define I365_RING_ENA 0x80 |
| #define I365_PC_RESET 0x40 |
| #define I365_PC_IOCARD 0x20 |
| #define I365_INTR_ENA 0x10 |
| #define I365_IRQ_MASK 0x0F |
| |
| /* Flags for I365_CSC and I365_CSCINT*/ |
| #define I365_CSC_BVD1 0x01 |
| #define I365_CSC_STSCHG 0x01 |
| #define I365_CSC_BVD2 0x02 |
| #define I365_CSC_READY 0x04 |
| #define I365_CSC_DETECT 0x08 |
| #define I365_CSC_ANY 0x0F |
| #define I365_CSC_GPI 0x10 |
| |
| /* Flags for I365_ADDRWIN */ |
| #define I365_ENA_IO(map) (0x40 << (map)) |
| #define I365_ENA_MEM(map) (0x01 << (map)) |
| |
| /* Flags for I365_IOCTL */ |
| #define I365_IOCTL_MASK(map) (0x0F << (map<<2)) |
| #define I365_IOCTL_WAIT(map) (0x08 << (map<<2)) |
| #define I365_IOCTL_0WS(map) (0x04 << (map<<2)) |
| #define I365_IOCTL_IOCS16(map) (0x02 << (map<<2)) |
| #define I365_IOCTL_16BIT(map) (0x01 << (map<<2)) |
| |
| /* Flags for I365_GENCTL */ |
| #define I365_CTL_16DELAY 0x01 |
| #define I365_CTL_RESET 0x02 |
| #define I365_CTL_GPI_ENA 0x04 |
| #define I365_CTL_GPI_CTL 0x08 |
| #define I365_CTL_RESUME 0x10 |
| #define I365_CTL_SW_IRQ 0x20 |
| |
| /* Flags for I365_GBLCTL */ |
| #define I365_GBL_PWRDOWN 0x01 |
| #define I365_GBL_CSC_LEV 0x02 |
| #define I365_GBL_WRBACK 0x04 |
| #define I365_GBL_IRQ_0_LEV 0x08 |
| #define I365_GBL_IRQ_1_LEV 0x10 |
| |
| /* Flags for memory window registers */ |
| #define I365_MEM_16BIT 0x8000 /* In memory start high byte */ |
| #define I365_MEM_0WS 0x4000 |
| #define I365_MEM_WS1 0x8000 /* In memory stop high byte */ |
| #define I365_MEM_WS0 0x4000 |
| #define I365_MEM_WRPROT 0x8000 /* In offset high byte */ |
| #define I365_MEM_REG 0x4000 |
| |
| #define I365_REG(slot, reg) (((slot) << 6) + reg) |
| |
| #endif /* _LINUX_I82365_H */ |
| |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| // Beginning vg468.h (for VADEM chipset) |
| |
| #ifndef _LINUX_VG468_H |
| #define _LINUX_VG468_H |
| |
| /* Special bit in I365_IDENT used for Vadem chip detection */ |
| #define I365_IDENT_VADEM 0x08 |
| |
| /* Special definitions in I365_POWER */ |
| #define VG468_VPP2_MASK 0x0c |
| #define VG468_VPP2_5V 0x04 |
| #define VG468_VPP2_12V 0x08 |
| |
| /* Unique Vadem registers */ |
| #define VG469_VSENSE 0x1f /* Card voltage sense */ |
| #define VG469_VSELECT 0x2f /* Card voltage select */ |
| #define VG468_CTL 0x38 /* Control register */ |
| #define VG468_TIMER 0x39 /* Timer control */ |
| #define VG468_MISC 0x3a /* Miscellaneous */ |
| #define VG468_GPIO_CFG 0x3b /* GPIO configuration */ |
| #define VG469_EXT_MODE 0x3c /* Extended mode register */ |
| #define VG468_SELECT 0x3d /* Programmable chip select */ |
| #define VG468_SELECT_CFG 0x3e /* Chip select configuration */ |
| #define VG468_ATA 0x3f /* ATA control */ |
| |
| /* Flags for VG469_VSENSE */ |
| #define VG469_VSENSE_A_VS1 0x01 |
| #define VG469_VSENSE_A_VS2 0x02 |
| #define VG469_VSENSE_B_VS1 0x04 |
| #define VG469_VSENSE_B_VS2 0x08 |
| |
| /* Flags for VG469_VSELECT */ |
| #define VG469_VSEL_VCC 0x03 |
| #define VG469_VSEL_5V 0x00 |
| #define VG469_VSEL_3V 0x03 |
| #define VG469_VSEL_MAX 0x0c |
| #define VG469_VSEL_EXT_STAT 0x10 |
| #define VG469_VSEL_EXT_BUS 0x20 |
| #define VG469_VSEL_MIXED 0x40 |
| #define VG469_VSEL_ISA 0x80 |
| |
| /* Flags for VG468_CTL */ |
| #define VG468_CTL_SLOW 0x01 /* 600ns memory timing */ |
| #define VG468_CTL_ASYNC 0x02 /* Asynchronous bus clocking */ |
| #define VG468_CTL_TSSI 0x08 /* Tri-state some outputs */ |
| #define VG468_CTL_DELAY 0x10 /* Card detect debounce */ |
| #define VG468_CTL_INPACK 0x20 /* Obey INPACK signal? */ |
| #define VG468_CTL_POLARITY 0x40 /* VCCEN polarity */ |
| #define VG468_CTL_COMPAT 0x80 /* Compatibility stuff */ |
| |
| #define VG469_CTL_WS_COMPAT 0x04 /* Wait state compatibility */ |
| #define VG469_CTL_STRETCH 0x10 /* LED stretch */ |
| |
| /* Flags for VG468_TIMER */ |
| #define VG468_TIMER_ZEROPWR 0x10 /* Zero power control */ |
| #define VG468_TIMER_SIGEN 0x20 /* Power up */ |
| #define VG468_TIMER_STATUS 0x40 /* Activity timer status */ |
| #define VG468_TIMER_RES 0x80 /* Timer resolution */ |
| #define VG468_TIMER_MASK 0x0f /* Activity timer timeout */ |
| |
| /* Flags for VG468_MISC */ |
| #define VG468_MISC_GPIO 0x04 /* General-purpose IO */ |
| #define VG468_MISC_DMAWSB 0x08 /* DMA wait state control */ |
| #define VG469_MISC_LEDENA 0x10 /* LED enable */ |
| #define VG468_MISC_VADEMREV 0x40 /* Vadem revision control */ |
| #define VG468_MISC_UNLOCK 0x80 /* Unique register lock */ |
| |
| /* Flags for VG469_EXT_MODE_A */ |
| #define VG469_MODE_VPPST 0x03 /* Vpp steering control */ |
| #define VG469_MODE_INT_SENSE 0x04 /* Internal voltage sense */ |
| #define VG469_MODE_CABLE 0x08 |
| #define VG469_MODE_COMPAT 0x10 /* i82365sl B or DF step */ |
| #define VG469_MODE_TEST 0x20 |
| #define VG469_MODE_RIO 0x40 /* Steer RIO to INTR? */ |
| |
| /* Flags for VG469_EXT_MODE_B */ |
| #define VG469_MODE_B_3V 0x01 /* 3.3v for socket B */ |
| |
| #endif /* _LINUX_VG468_H */ |
| |
| |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| // Beginning ricoh.h (RICOH chipsets) |
| |
| #ifndef _LINUX_RICOH_H |
| #define _LINUX_RICOH_H |
| |
| |
| #define RF5C_MODE_CTL 0x1f /* Mode control */ |
| #define RF5C_PWR_CTL 0x2f /* Mixed voltage control */ |
| #define RF5C_CHIP_ID 0x3a /* Chip identification */ |
| #define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */ |
| |
| /* I/O window address offset */ |
| #define RF5C_IO_OFF(w) (0x36+((w)<<1)) |
| |
| /* Flags for RF5C_MODE_CTL */ |
| #define RF5C_MODE_ATA 0x01 /* ATA mode */ |
| #define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */ |
| #define RF5C_MODE_CA21 0x04 |
| #define RF5C_MODE_CA22 0x08 |
| #define RF5C_MODE_CA23 0x10 |
| #define RF5C_MODE_CA24 0x20 |
| #define RF5C_MODE_CA25 0x40 |
| #define RF5C_MODE_3STATE_BIT7 0x80 |
| |
| /* Flags for RF5C_PWR_CTL */ |
| #define RF5C_PWR_VCC_3V 0x01 |
| #define RF5C_PWR_IREQ_HIGH 0x02 |
| #define RF5C_PWR_INPACK_ENA 0x04 |
| #define RF5C_PWR_5V_DET 0x08 |
| #define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */ |
| #define RF5C_PWR_DREQ_LOW 0x20 |
| #define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */ |
| #define RF5C_PWR_DREQ_INPACK 0x40 |
| #define RF5C_PWR_DREQ_SPKR 0x80 |
| #define RF5C_PWR_DREQ_IOIS16 0xc0 |
| |
| /* Values for RF5C_CHIP_ID */ |
| #define RF5C_CHIP_RF5C296 0x32 |
| #define RF5C_CHIP_RF5C396 0xb2 |
| |
| /* Flags for RF5C_MODE_CTL_3 */ |
| #define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */ |
| #define RF5C_MCTL3_DMA_ENA 0x02 |
| |
| /* Register definitions for Ricoh PCI-to-CardBus bridges */ |
| |
| /* Extra bits in CB_BRIDGE_CONTROL */ |
| #define RL5C46X_BCR_3E0_ENA 0x0800 |
| #define RL5C46X_BCR_3E2_ENA 0x1000 |
| |
| /* Bridge Configuration Register */ |
| #define RL5C4XX_CONFIG 0x80 /* 16 bit */ |
| #define RL5C4XX_CONFIG_IO_1_MODE 0x0200 |
| #define RL5C4XX_CONFIG_IO_0_MODE 0x0100 |
| #define RL5C4XX_CONFIG_PREFETCH 0x0001 |
| |
| |
| /* Misc Control Register */ |
| #define RL5C4XX_MISC 0x0082 /* 16 bit */ |
| #define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002 |
| #define RL5C4XX_MISC_VCCEN_POL 0x0100 |
| #define RL5C4XX_MISC_VPPEN_POL 0x0200 |
| #define RL5C46X_MISC_SUSPEND 0x0001 |
| #define RL5C46X_MISC_PWR_SAVE_2 0x0004 |
| #define RL5C46X_MISC_IFACE_BUSY 0x0008 |
| #define RL5C46X_MISC_B_LOCK 0x0010 |
| #define RL5C46X_MISC_A_LOCK 0x0020 |
| #define RL5C46X_MISC_PCI_LOCK 0x0040 |
| #define RL5C47X_MISC_IFACE_BUSY 0x0004 |
| #define RL5C47X_MISC_PCI_INT_MASK 0x0018 |
| #define RL5C47X_MISC_PCI_INT_DIS 0x0020 |
| #define RL5C47X_MISC_SUBSYS_WR 0x0040 |
| #define RL5C47X_MISC_SRIRQ_ENA 0x0080 |
| #define RL5C47X_MISC_5V_DISABLE 0x0400 |
| #define RL5C47X_MISC_LED_POL 0x0800 |
| |
| /* 16-bit Interface Control Register */ |
| #define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */ |
| #define RL5C4XX_16CTL_IO_TIMING 0x0100 |
| #define RL5C4XX_16CTL_MEM_TIMING 0x0200 |
| #define RL5C46X_16CTL_LEVEL_1 0x0010 |
| #define RL5C46X_16CTL_LEVEL_2 0x0020 |
| |
| /* 16-bit IO and memory timing registers */ |
| #define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */ |
| #define RL5C4XX_16BIT_MEM_0 0x0088 /* 16 bit */ |
| #define RL5C4XX_SETUP_MASK 0x0007 |
| #define RL5C4XX_SETUP_SHIFT 0 |
| #define RL5C4XX_CMD_MASK 0x01f0 |
| #define RL5C4XX_CMD_SHIFT 4 |
| #define RL5C4XX_HOLD_MASK 0x1c00 |
| #define RL5C4XX_HOLD_SHIFT 10 |
| #define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */ |
| #define RL5C4XX_ZV_ENABLE 0x08 |
| |
| #endif /* _LINUX_RICOH_H */ |
| |
| |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| //***************************************************************************** |
| // Beginning cirrus.h (CIRRUS chipsets) |
| |
| #ifndef _LINUX_CIRRUS_H |
| #define _LINUX_CIRRUS_H |
| |
| #ifndef PCI_VENDOR_ID_CIRRUS |
| #define PCI_VENDOR_ID_CIRRUS 0x1013 |
| #endif |
| #ifndef PCI_DEVICE_ID_CIRRUS_6729 |
| #define PCI_DEVICE_ID_CIRRUS_6729 0x1100 |
| #endif |
| #ifndef PCI_DEVICE_ID_CIRRUS_6832 |
| #define PCI_DEVICE_ID_CIRRUS_6832 0x1110 |
| #endif |
| |
| #define PD67_MISC_CTL_1 0x16 /* Misc control 1 */ |
| #define PD67_FIFO_CTL 0x17 /* FIFO control */ |
| #define PD67_MISC_CTL_2 0x1E /* Misc control 2 */ |
| #define PD67_CHIP_INFO 0x1f /* Chip information */ |
| #define PD67_ATA_CTL 0x026 /* 6730: ATA control */ |
| #define PD67_EXT_INDEX 0x2e /* Extension index */ |
| #define PD67_EXT_DATA 0x2f /* Extension data */ |
| |
| /* PD6722 extension registers -- indexed in PD67_EXT_INDEX */ |
| #define PD67_DATA_MASK0 0x01 /* Data mask 0 */ |
| #define PD67_DATA_MASK1 0x02 /* Data mask 1 */ |
| #define PD67_DMA_CTL 0x03 /* DMA control */ |
| |
| /* PD6730 extension registers -- indexed in PD67_EXT_INDEX */ |
| #define PD67_EXT_CTL_1 0x03 /* Extension control 1 */ |
| #define PD67_MEM_PAGE(n) ((n)+5) /* PCI window bits 31:24 */ |
| #define PD67_EXTERN_DATA 0x0a |
| #define PD67_MISC_CTL_3 0x25 |
| #define PD67_SMB_PWR_CTL 0x26 |
| |
| /* I/O window address offset */ |
| #define PD67_IO_OFF(w) (0x36+((w)<<1)) |
| |
| /* Timing register sets */ |
| #define PD67_TIME_SETUP(n) (0x3a + 3*(n)) |
| #define PD67_TIME_CMD(n) (0x3b + 3*(n)) |
| #define PD67_TIME_RECOV(n) (0x3c + 3*(n)) |
| |
| /* Flags for PD67_MISC_CTL_1 */ |
| #define PD67_MC1_5V_DET 0x01 /* 5v detect */ |
| #define PD67_MC1_MEDIA_ENA 0x01 /* 6730: Multimedia enable */ |
| #define PD67_MC1_VCC_3V 0x02 /* 3.3v Vcc */ |
| #define PD67_MC1_PULSE_MGMT 0x04 |
| #define PD67_MC1_PULSE_IRQ 0x08 |
| #define PD67_MC1_SPKR_ENA 0x10 |
| #define PD67_MC1_INPACK_ENA 0x80 |
| |
| /* Flags for PD67_FIFO_CTL */ |
| #define PD67_FIFO_EMPTY 0x80 |
| |
| /* Flags for PD67_MISC_CTL_2 */ |
| #define PD67_MC2_FREQ_BYPASS 0x01 |
| #define PD67_MC2_DYNAMIC_MODE 0x02 |
| #define PD67_MC2_SUSPEND 0x04 |
| #define PD67_MC2_5V_CORE 0x08 |
| #define PD67_MC2_LED_ENA 0x10 /* IRQ 12 is LED enable */ |
| #define PD67_MC2_FAST_PCI 0x10 /* 6729: PCI bus > 25 MHz */ |
| #define PD67_MC2_3STATE_BIT7 0x20 /* Floppy change bit */ |
| #define PD67_MC2_DMA_MODE 0x40 |
| #define PD67_MC2_IRQ15_RI 0x80 /* IRQ 15 is ring enable */ |
| |
| /* Flags for PD67_CHIP_INFO */ |
| #define PD67_INFO_SLOTS 0x20 /* 0 = 1 slot, 1 = 2 slots */ |
| #define PD67_INFO_CHIP_ID 0xc0 |
| #define PD67_INFO_REV 0x1c |
| |
| /* Fields in PD67_TIME_* registers */ |
| #define PD67_TIME_SCALE 0xc0 |
| #define PD67_TIME_SCALE_1 0x00 |
| #define PD67_TIME_SCALE_16 0x40 |
| #define PD67_TIME_SCALE_256 0x80 |
| #define PD67_TIME_SCALE_4096 0xc0 |
| #define PD67_TIME_MULT 0x3f |
| |
| /* Fields in PD67_DMA_CTL */ |
| #define PD67_DMA_MODE 0xc0 |
| #define PD67_DMA_OFF 0x00 |
| #define PD67_DMA_DREQ_INPACK 0x40 |
| #define PD67_DMA_DREQ_WP 0x80 |
| #define PD67_DMA_DREQ_BVD2 0xc0 |
| #define PD67_DMA_PULLUP 0x20 /* Disable socket pullups? */ |
| |
| /* Fields in PD67_EXT_CTL_1 */ |
| #define PD67_EC1_VCC_PWR_LOCK 0x01 |
| #define PD67_EC1_AUTO_PWR_CLEAR 0x02 |
| #define PD67_EC1_LED_ENA 0x04 |
| #define PD67_EC1_INV_CARD_IRQ 0x08 |
| #define PD67_EC1_INV_MGMT_IRQ 0x10 |
| #define PD67_EC1_PULLUP_CTL 0x20 |
| |
| /* Fields in PD67_MISC_CTL_3 */ |
| #define PD67_MC3_IRQ_MASK 0x03 |
| #define PD67_MC3_IRQ_PCPCI 0x00 |
| #define PD67_MC3_IRQ_EXTERN 0x01 |
| #define PD67_MC3_IRQ_PCIWAY 0x02 |
| #define PD67_MC3_IRQ_PCI 0x03 |
| #define PD67_MC3_PWR_MASK 0x0c |
| #define PD67_MC3_PWR_SERIAL 0x00 |
| #define PD67_MC3_PWR_TI2202 0x08 |
| #define PD67_MC3_PWR_SMB 0x0c |
| |
| /* Register definitions for Cirrus PD6832 PCI-to-CardBus bridge */ |
| |
| /* PD6832 extension registers -- indexed in PD67_EXT_INDEX */ |
| #define PD68_EXT_CTL_2 0x0b |
| #define PD68_PCI_SPACE 0x22 |
| #define PD68_PCCARD_SPACE 0x23 |
| #define PD68_WINDOW_TYPE 0x24 |
| #define PD68_EXT_CSC 0x2e |
| #define PD68_MISC_CTL_4 0x2f |
| #define PD68_MISC_CTL_5 0x30 |
| #define PD68_MISC_CTL_6 0x31 |
| |
| /* Extra flags in PD67_MISC_CTL_3 */ |
| #define PD68_MC3_HW_SUSP 0x10 |
| #define PD68_MC3_MM_EXPAND 0x40 |
| #define PD68_MC3_MM_ARM 0x80 |
| |
| /* Bridge Control Register */ |
| #define PD6832_BCR_MGMT_IRQ_ENA 0x0800 |
| |
| /* Socket Number Register */ |
| #define PD6832_SOCKET_NUMBER 0x004c /* 8 bit */ |
| |
| #endif /* _LINUX_CIRRUS_H */ |
| |
| |
| |
