| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * (C) Copyright 2008 |
| * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. |
| * |
| * Wolfgang Denk <wd@denx.de> |
| * Copyright 2004 Freescale Semiconductor. |
| * (C) Copyright 2002,2003 Motorola,Inc. |
| * Xianghua Xiao <X.Xiao@motorola.com> |
| */ |
| |
| /* |
| * Socrates |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * Only possible on E500 Version 2 or newer cores. |
| */ |
| |
| /* |
| * sysclk for MPC85xx |
| * |
| * Two valid values are: |
| * 33000000 |
| * 66000000 |
| * |
| * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz |
| * is likely the desired value here, so that is now the default. |
| * The board, however, can run at 66MHz. In any event, this value |
| * must match the settings of some switches. Details can be found |
| * in the README.mpc85xxads. |
| */ |
| |
| #define CFG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ |
| |
| #undef CFG_SYS_DRAM_TEST /* memory test, takes time */ |
| |
| #define CFG_SYS_CCSRBAR 0xE0000000 |
| #define CFG_SYS_CCSRBAR_PHYS_LOW CFG_SYS_CCSRBAR |
| |
| /* DDR Setup */ |
| #define CFG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE |
| |
| /* I2C addresses of SPD EEPROMs */ |
| #define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */ |
| |
| /* Hardcoded values, to use instead of SPD */ |
| #define CFG_SYS_DDR_CS0_BNDS 0x0000000f |
| #define CFG_SYS_DDR_CS0_CONFIG 0x80010102 |
| #define CFG_SYS_DDR_TIMING_0 0x00260802 |
| #define CFG_SYS_DDR_TIMING_1 0x3935D322 |
| #define CFG_SYS_DDR_TIMING_2 0x14904CC8 |
| #define CFG_SYS_DDR_MODE 0x00480432 |
| #define CFG_SYS_DDR_INTERVAL 0x030C0100 |
| #define CFG_SYS_DDR_CONFIG_2 0x04400000 |
| #define CFG_SYS_DDR_CONFIG 0xC3008000 |
| #define CFG_SYS_DDR_CLK_CONTROL 0x03800000 |
| #define CFG_SYS_SDRAM_SIZE 256 /* in Megs */ |
| |
| /* |
| * Flash on the LocalBus |
| */ |
| #define CFG_SYS_FLASH0 0xFE000000 |
| #define CFG_SYS_FLASH_BANKS_LIST { CFG_SYS_FLASH0 } |
| |
| #define CFG_SYS_LBC_FLASH_BASE CFG_SYS_FLASH0 /* Localbus flash start */ |
| #define CFG_SYS_FLASH_BASE CFG_SYS_LBC_FLASH_BASE /* start of FLASH */ |
| |
| #define CFG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ |
| #define CFG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ |
| #define CFG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ |
| #define CFG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ |
| |
| #define CFG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ |
| #define CFG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/ |
| |
| #define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| /* FPGA and NAND */ |
| #define CFG_SYS_FPGA_BASE 0xc0000000 |
| #define CFG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */ |
| |
| #define CFG_SYS_NAND_BASE (CFG_SYS_FPGA_BASE + 0x70) |
| |
| /* LIME GDC */ |
| #define CFG_SYS_LIME_BASE 0xc8000000 |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1. |
| */ |
| |
| #define CFG_SYS_PCI1_MEM_PHYS 0x80000000 |
| #define CFG_SYS_PCI1_IO_PHYS 0xE2000000 |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| #define CFG_ENV_FLAGS_LIST_STATIC "ethaddr:mw,eth1addr:mw,system1_addr:xw,serial#:sw,ethact:sw,ethprime:sw" |
| |
| /* pass open firmware flat tree */ |
| |
| #endif /* __CONFIG_H */ |
