include/configs/T4240RDB.h - u-boot - Git at Google

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  * Copyright 2020-2023 NXP
  */

 /*
  * T4240 RDB board configuration file
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H

 #include <linux/stringify.h>

 #define CFG_ICS307_REFCLK_HZ		25000000  /* ICS307 ref clk freq */

 #ifdef CONFIG_RAMBOOT_PBL
 #ifndef CONFIG_SDCARD
 #define CFG_RESET_VECTOR_ADDRESS     0xfffffffc
 #else
 #define RESET_VECTOR_OFFSET		0x27FFC
 #define BOOT_PAGE_OFFSET		0x27000

 #ifdef	CONFIG_SDCARD
 #define CFG_RESET_VECTOR_ADDRESS	0x200FFC
 #define CFG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
 #define CFG_SYS_MMC_U_BOOT_DST	0x00200000
 #define CFG_SYS_MMC_U_BOOT_START	0x00200000
 #define CFG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
 #endif

 #endif
 #endif /* CONFIG_RAMBOOT_PBL */

 /* High Level Configuration Options */

 #ifndef CFG_RESET_VECTOR_ADDRESS
 #define CFG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif

 #define CFG_SYS_NUM_CPC		CONFIG_SYS_NUM_DDR_CTLRS

 /*
  *  Config the L3 Cache as L3 SRAM
  */
 #define CFG_SYS_INIT_L3_ADDR		0xFFFC0000
 #define SPL_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)

 #define CFG_SYS_DCSRBAR		0xf0000000
 #define CFG_SYS_DCSRBAR_PHYS		0xf00000000ull

 /*
  * DDR Setup
  */
 #define CFG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CFG_SYS_SDRAM_BASE		CFG_SYS_DDR_SDRAM_BASE

 /*
  * IFC Definitions
  */
 #define CFG_SYS_FLASH_BASE	0xe0000000
 #define CFG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CFG_SYS_FLASH_BASE)

 /* define to use L1 as initial stack */
 #define CFG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
 #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe03c000
 /* The assembler doesn't like typecast */
 #define CFG_SYS_INIT_RAM_ADDR_PHYS \
 	((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 	  CFG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 #define CFG_SYS_INIT_RAM_SIZE		0x00004000

 #define CFG_SYS_INIT_SP_OFFSET	(CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

 /* Serial Port - controlled on board with jumper J8
  * open - index 2
  * shorted - index 1
  */
 #if !CONFIG_IS_ENABLED(DM_SERIAL)
 #define CFG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
 #endif

 #define CFG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CFG_SYS_NS16550_COM1	(CFG_SYS_CCSRBAR+0x11C500)
 #define CFG_SYS_NS16550_COM2	(CFG_SYS_CCSRBAR+0x11C600)
 #define CFG_SYS_NS16550_COM3	(CFG_SYS_CCSRBAR+0x11D500)
 #define CFG_SYS_NS16550_COM4	(CFG_SYS_CCSRBAR+0x11D600)

 /* I2C */

 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */

 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 #define CFG_SYS_PCIE1_MEM_VIRT	0x80000000
 #define CFG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
 #define CFG_SYS_PCIE1_IO_VIRT	0xf8000000
 #define CFG_SYS_PCIE1_IO_PHYS	0xff8000000ull

 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 #define CFG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #define CFG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
 #define CFG_SYS_PCIE2_IO_VIRT	0xf8010000
 #define CFG_SYS_PCIE2_IO_PHYS	0xff8010000ull

 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 #define CFG_SYS_PCIE3_MEM_VIRT	0xc0000000
 #define CFG_SYS_PCIE3_MEM_PHYS	0xc40000000ull

 /* controller 4, Base address 203000 */
 #define CFG_SYS_PCIE4_MEM_BUS	0xe0000000
 #define CFG_SYS_PCIE4_MEM_PHYS	0xc60000000ull

 /*
  * Miscellaneous configurable options
  */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/

 /*
  * Environment Configuration
  */

 #define HVBOOT					\
 	"setenv bootargs config-addr=0x60000000; "	\
 	"bootm 0x01000000 - 0x00f00000"

 /*
  * DDR Setup
  */
 #define SPD_EEPROM_ADDRESS1	0x52
 #define SPD_EEPROM_ADDRESS2	0x54
 #define SPD_EEPROM_ADDRESS3	0x56
 #define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1	/* for p3041/p5010 */
 #define CFG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */

 /*
  * IFC Definitions
  */
 #define CFG_SYS_NOR0_CSPR_EXT	(0xf)
 #define CFG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS \
 				+ 0x8000000) | \
 				CSPR_PORT_SIZE_16 | \
 				CSPR_MSEL_NOR | \
 				CSPR_V)
 #define CFG_SYS_NOR1_CSPR_EXT	(0xf)
 #define CFG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS) | \
 				CSPR_PORT_SIZE_16 | \
 				CSPR_MSEL_NOR | \
 				CSPR_V)
 #define CFG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
 /* NOR Flash Timing Params */
 #define CFG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80

 #define CFG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
 				FTIM0_NOR_TEADC(0x5) | \
 				FTIM0_NOR_TEAHC(0x5))
 #define CFG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
 				FTIM1_NOR_TRAD_NOR(0x1A) |\
 				FTIM1_NOR_TSEQRAD_NOR(0x13))
 #define CFG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
 				FTIM2_NOR_TCH(0x4) | \
 				FTIM2_NOR_TWPH(0x0E) | \
 				FTIM2_NOR_TWP(0x1c))
 #define CFG_SYS_NOR_FTIM3	0x0

 #define CFG_SYS_FLASH_BANKS_LIST	{CFG_SYS_FLASH_BASE_PHYS \
 					+ 0x8000000, CFG_SYS_FLASH_BASE_PHYS}

 /* NAND Flash on IFC */
 #define CFG_SYS_NAND_BASE		0xff800000
 #define CFG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CFG_SYS_NAND_BASE)

 #define CFG_SYS_NAND_CSPR_EXT	(0xf)
 #define CFG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
 				| CSPR_V)
 #define CFG_SYS_NAND_AMASK	IFC_AMASK(64*1024)

 #define CFG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 				| CSOR_NAND_RAL_3	/* RAL = 2Byes */ \
 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
 				| CSOR_NAND_PB(128))	/*Page Per Block = 128*/

 /* ONFI NAND Flash mode0 Timing Params */
 #define CFG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
 					FTIM0_NAND_TWP(0x18)   | \
 					FTIM0_NAND_TWCHT(0x07) | \
 					FTIM0_NAND_TWH(0x0a))
 #define CFG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
 					FTIM1_NAND_TWBE(0x39)  | \
 					FTIM1_NAND_TRR(0x0e)   | \
 					FTIM1_NAND_TRP(0x18))
 #define CFG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
 					FTIM2_NAND_TREH(0x0a) | \
 					FTIM2_NAND_TWHRE(0x1e))
 #define CFG_SYS_NAND_FTIM3		0x0

 #define CFG_SYS_NAND_BASE_LIST	{ CFG_SYS_NAND_BASE }

 #if defined(CONFIG_MTD_RAW_NAND)
 #define CFG_SYS_CSPR0_EXT		CFG_SYS_NAND_CSPR_EXT
 #define CFG_SYS_CSPR0		CFG_SYS_NAND_CSPR
 #define CFG_SYS_AMASK0		CFG_SYS_NAND_AMASK
 #define CFG_SYS_CSOR0		CFG_SYS_NAND_CSOR
 #define CFG_SYS_CS0_FTIM0		CFG_SYS_NAND_FTIM0
 #define CFG_SYS_CS0_FTIM1		CFG_SYS_NAND_FTIM1
 #define CFG_SYS_CS0_FTIM2		CFG_SYS_NAND_FTIM2
 #define CFG_SYS_CS0_FTIM3		CFG_SYS_NAND_FTIM3
 #define CFG_SYS_CSPR2_EXT		CFG_SYS_NOR0_CSPR_EXT
 #define CFG_SYS_CSPR2		CFG_SYS_NOR0_CSPR
 #define CFG_SYS_AMASK2		CFG_SYS_NOR_AMASK
 #define CFG_SYS_CSOR2		CFG_SYS_NOR_CSOR
 #define CFG_SYS_CS2_FTIM0		CFG_SYS_NOR_FTIM0
 #define CFG_SYS_CS2_FTIM1		CFG_SYS_NOR_FTIM1
 #define CFG_SYS_CS2_FTIM2		CFG_SYS_NOR_FTIM2
 #define CFG_SYS_CS2_FTIM3		CFG_SYS_NOR_FTIM3
 #else
 #define CFG_SYS_CSPR0_EXT		CFG_SYS_NOR0_CSPR_EXT
 #define CFG_SYS_CSPR0		CFG_SYS_NOR0_CSPR
 #define CFG_SYS_AMASK0		CFG_SYS_NOR_AMASK
 #define CFG_SYS_CSOR0		CFG_SYS_NOR_CSOR
 #define CFG_SYS_CS0_FTIM0		CFG_SYS_NOR_FTIM0
 #define CFG_SYS_CS0_FTIM1		CFG_SYS_NOR_FTIM1
 #define CFG_SYS_CS0_FTIM2		CFG_SYS_NOR_FTIM2
 #define CFG_SYS_CS0_FTIM3		CFG_SYS_NOR_FTIM3
 #define CFG_SYS_CSPR1_EXT		CFG_SYS_NAND_CSPR_EXT
 #define CFG_SYS_CSPR1		CFG_SYS_NAND_CSPR
 #define CFG_SYS_AMASK1		CFG_SYS_NAND_AMASK
 #define CFG_SYS_CSOR1		CFG_SYS_NAND_CSOR
 #define CFG_SYS_CS1_FTIM0		CFG_SYS_NAND_FTIM0
 #define CFG_SYS_CS1_FTIM1		CFG_SYS_NAND_FTIM1
 #define CFG_SYS_CS1_FTIM2		CFG_SYS_NAND_FTIM2
 #define CFG_SYS_CS1_FTIM3		CFG_SYS_NAND_FTIM3
 #endif
 #define CFG_SYS_CSPR2_EXT		CFG_SYS_NOR1_CSPR_EXT
 #define CFG_SYS_CSPR2		CFG_SYS_NOR1_CSPR
 #define CFG_SYS_AMASK2		CFG_SYS_NOR_AMASK
 #define CFG_SYS_CSOR2		CFG_SYS_NOR_CSOR
 #define CFG_SYS_CS2_FTIM0		CFG_SYS_NOR_FTIM0
 #define CFG_SYS_CS2_FTIM1		CFG_SYS_NOR_FTIM1
 #define CFG_SYS_CS2_FTIM2		CFG_SYS_NOR_FTIM2
 #define CFG_SYS_CS2_FTIM3		CFG_SYS_NOR_FTIM3

 /* CPLD on IFC */
 #define CFG_SYS_CPLD_BASE	0xffdf0000
 #define CFG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CFG_SYS_CPLD_BASE)
 #define CFG_SYS_CSPR3_EXT	(0xf)
 #define CFG_SYS_CSPR3	(CSPR_PHYS_ADDR(CFG_SYS_CPLD_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8 \
 				| CSPR_MSEL_GPCM \
 				| CSPR_V)

 #define CFG_SYS_AMASK3	IFC_AMASK(64 * 1024)
 #define CFG_SYS_CSOR3	0x0

 /* CPLD Timing parameters for IFC CS3 */
 #define CFG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
 					FTIM0_GPCM_TEADC(0x0e) | \
 					FTIM0_GPCM_TEAHC(0x0e))
 #define CFG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
 					FTIM1_GPCM_TRAD(0x1f))
 #define CFG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
 					FTIM2_GPCM_TCH(0x8) | \
 					FTIM2_GPCM_TWP(0x1f))
 #define CFG_SYS_CS3_FTIM3		0x0

 /* I2C */
 #define I2C_MUX_PCA_ADDR_PRI		0x77 /* I2C bus multiplexer,primary */
 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* I2C bus multiplexer,secondary */

 #define I2C_MUX_CH_DEFAULT	0x8
 #define I2C_MUX_CH_VOL_MONITOR	0xa
 #define I2C_MUX_CH_VSC3316_FS	0xc
 #define I2C_MUX_CH_VSC3316_BS	0xd

 /* Voltage monitor on channel 2*/
 #define I2C_VOL_MONITOR_ADDR		0x40
 #define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
 #define I2C_VOL_MONITOR_BUS_V_OVF	0x1
 #define I2C_VOL_MONITOR_BUS_V_SHIFT	3

 /* The lowest and highest voltage allowed for T4240RDB */
 #define VDD_MV_MIN			819
 #define VDD_MV_MAX			1212

 /*
  * eSPI - Enhanced SPI
  */

 /* Qman/Bman */
 #ifndef CONFIG_NOBQFMAN
 #define CFG_SYS_BMAN_NUM_PORTALS	50
 #define CFG_SYS_BMAN_MEM_BASE	0xf4000000
 #define CFG_SYS_BMAN_MEM_PHYS	0xff4000000ull
 #define CFG_SYS_BMAN_MEM_SIZE	0x02000000
 #define CFG_SYS_BMAN_SP_CENA_SIZE    0x4000
 #define CFG_SYS_BMAN_SP_CINH_SIZE    0x1000
 #define CFG_SYS_BMAN_CENA_BASE       CFG_SYS_BMAN_MEM_BASE
 #define CFG_SYS_BMAN_CENA_SIZE       (CFG_SYS_BMAN_MEM_SIZE >> 1)
 #define CFG_SYS_BMAN_CINH_BASE       (CFG_SYS_BMAN_MEM_BASE + \
 					CFG_SYS_BMAN_CENA_SIZE)
 #define CFG_SYS_BMAN_CINH_SIZE       (CFG_SYS_BMAN_MEM_SIZE >> 1)
 #define CFG_SYS_BMAN_SWP_ISDR_REG    0xE08
 #define CFG_SYS_QMAN_NUM_PORTALS	50
 #define CFG_SYS_QMAN_MEM_BASE	0xf6000000
 #define CFG_SYS_QMAN_MEM_PHYS	0xff6000000ull
 #define CFG_SYS_QMAN_MEM_SIZE	0x02000000
 #define CFG_SYS_QMAN_SP_CINH_SIZE    0x1000
 #define CFG_SYS_QMAN_CENA_SIZE       (CFG_SYS_QMAN_MEM_SIZE >> 1)
 #define CFG_SYS_QMAN_CINH_BASE       (CFG_SYS_QMAN_MEM_BASE + \
 					CFG_SYS_QMAN_CENA_SIZE)
 #define CFG_SYS_QMAN_CINH_SIZE       (CFG_SYS_QMAN_MEM_SIZE >> 1)
 #define CFG_SYS_QMAN_SWP_ISDR_REG	0xE08
 #endif /* CONFIG_NOBQFMAN */

 #ifdef CONFIG_SYS_DPAA_FMAN
 #define SGMII_PHY_ADDR1 0x0
 #define SGMII_PHY_ADDR2 0x1
 #define SGMII_PHY_ADDR3 0x2
 #define SGMII_PHY_ADDR4 0x3
 #define SGMII_PHY_ADDR5 0x4
 #define SGMII_PHY_ADDR6 0x5
 #define SGMII_PHY_ADDR7 0x6
 #define SGMII_PHY_ADDR8 0x7
 #define FM1_10GEC1_PHY_ADDR	0x10
 #define FM1_10GEC2_PHY_ADDR	0x11
 #define FM2_10GEC1_PHY_ADDR	0x12
 #define FM2_10GEC2_PHY_ADDR	0x13
 #define CORTINA_PHY_ADDR1	FM1_10GEC1_PHY_ADDR
 #define CORTINA_PHY_ADDR2	FM1_10GEC2_PHY_ADDR
 #define CORTINA_PHY_ADDR3	FM2_10GEC1_PHY_ADDR
 #define CORTINA_PHY_ADDR4	FM2_10GEC2_PHY_ADDR
 #endif

 /*
 * USB
 */

 #ifdef CONFIG_MMC
 #define CFG_SYS_FSL_ESDHC_ADDR       CFG_SYS_MPC85xx_ESDHC_ADDR
 #endif

 #define __USB_PHY_TYPE	utmi

 /*
  * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
  * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
  * interleaving. It can be cacheline, page, bank, superbank.
  * See doc/README.fsl-ddr for details.
  */
 #ifdef CONFIG_ARCH_T4240
 #define CTRL_INTLV_PREFERED 3way_4KB
 #else
 #define CTRL_INTLV_PREFERED cacheline
 #endif

 #define	CFG_EXTRA_ENV_SETTINGS				\
 	"hwconfig=fsl_ddr:"					\
 	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
 	"bank_intlv=auto;"					\
 	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 	"netdev=eth0\0"						\
 	"uboot=" CONFIG_UBOOTPATH "\0"		\
 	"ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0"	\
 	"tftpflash=tftpboot $loadaddr $uboot && "		\
 	"protect off $ubootaddr +$filesize && "			\
 	"erase $ubootaddr +$filesize && "			\
 	"cp.b $loadaddr $ubootaddr $filesize && "		\
 	"protect on $ubootaddr +$filesize && "			\
 	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
 	"consoledev=ttyS0\0"					\
 	"ramdiskaddr=2000000\0"					\
 	"ramdiskfile=t4240rdb/ramdisk.uboot\0"			\
 	"fdtaddr=1e00000\0"					\
 	"fdtfile=t4240rdb/t4240rdb.dtb\0"			\
 	"bdev=sda3\0"

 #define HVBOOT					\
 	"setenv bootargs config-addr=0x60000000; "	\
 	"bootm 0x01000000 - 0x00f00000"

 #include <asm/fsl_secure_boot.h>

 #endif	/* __CONFIG_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2014 Freescale Semiconductor, Inc.
	* Copyright 2020-2023 NXP
	*/

	/*
	* T4240 RDB board configuration file
	*/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	#include <linux/stringify.h>

	#define CFG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */

	#ifdef CONFIG_RAMBOOT_PBL
	#ifndef CONFIG_SDCARD
	#define CFG_RESET_VECTOR_ADDRESS 0xfffffffc
	#else
	#define RESET_VECTOR_OFFSET 0x27FFC
	#define BOOT_PAGE_OFFSET 0x27000

	#ifdef CONFIG_SDCARD
	#define CFG_RESET_VECTOR_ADDRESS 0x200FFC
	#define CFG_SYS_MMC_U_BOOT_SIZE (768 << 10)
	#define CFG_SYS_MMC_U_BOOT_DST 0x00200000
	#define CFG_SYS_MMC_U_BOOT_START 0x00200000
	#define CFG_SYS_MMC_U_BOOT_OFFS (260 << 10)
	#endif

	#endif
	#endif /* CONFIG_RAMBOOT_PBL */

	/* High Level Configuration Options */

	#ifndef CFG_RESET_VECTOR_ADDRESS
	#define CFG_RESET_VECTOR_ADDRESS 0xeffffffc
	#endif

	#define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS

	/*
	* Config the L3 Cache as L3 SRAM
	*/
	#define CFG_SYS_INIT_L3_ADDR 0xFFFC0000
	#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)

	#define CFG_SYS_DCSRBAR 0xf0000000
	#define CFG_SYS_DCSRBAR_PHYS 0xf00000000ull

	/*
	* DDR Setup
	*/
	#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
	#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE

	/*
	* IFC Definitions
	*/
	#define CFG_SYS_FLASH_BASE 0xe0000000
	#define CFG_SYS_FLASH_BASE_PHYS (0xf00000000ull \| CFG_SYS_FLASH_BASE)

	/* define to use L1 as initial stack */
	#define CFG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
	#define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
	#define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
	/* The assembler doesn't like typecast */
	#define CFG_SYS_INIT_RAM_ADDR_PHYS \
	((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) \| \
	CFG_SYS_INIT_RAM_ADDR_PHYS_LOW)
	#define CFG_SYS_INIT_RAM_SIZE 0x00004000

	#define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

	/* Serial Port - controlled on board with jumper J8
	* open - index 2
	* shorted - index 1
	*/
	#if !CONFIG_IS_ENABLED(DM_SERIAL)
	#define CFG_SYS_NS16550_CLK (get_bus_freq(0)/2)
	#endif

	#define CFG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CFG_SYS_NS16550_COM1 (CFG_SYS_CCSRBAR+0x11C500)
	#define CFG_SYS_NS16550_COM2 (CFG_SYS_CCSRBAR+0x11C600)
	#define CFG_SYS_NS16550_COM3 (CFG_SYS_CCSRBAR+0x11D500)
	#define CFG_SYS_NS16550_COM4 (CFG_SYS_CCSRBAR+0x11D600)

	/* I2C */

	/*
	* General PCI
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/

	/* controller 1, direct to uli, tgtid 3, Base address 20000 */
	#define CFG_SYS_PCIE1_MEM_VIRT 0x80000000
	#define CFG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
	#define CFG_SYS_PCIE1_IO_VIRT 0xf8000000
	#define CFG_SYS_PCIE1_IO_PHYS 0xff8000000ull

	/* controller 2, Slot 2, tgtid 2, Base address 201000 */
	#define CFG_SYS_PCIE2_MEM_VIRT 0xa0000000
	#define CFG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
	#define CFG_SYS_PCIE2_IO_VIRT 0xf8010000
	#define CFG_SYS_PCIE2_IO_PHYS 0xff8010000ull

	/* controller 3, Slot 1, tgtid 1, Base address 202000 */
	#define CFG_SYS_PCIE3_MEM_VIRT 0xc0000000
	#define CFG_SYS_PCIE3_MEM_PHYS 0xc40000000ull

	/* controller 4, Base address 203000 */
	#define CFG_SYS_PCIE4_MEM_BUS 0xe0000000
	#define CFG_SYS_PCIE4_MEM_PHYS 0xc60000000ull

	/*
	* Miscellaneous configurable options
	*/

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/

	/*
	* Environment Configuration
	*/

	#define HVBOOT \
	"setenv bootargs config-addr=0x60000000; " \
	"bootm 0x01000000 - 0x00f00000"

	/*
	* DDR Setup
	*/
	#define SPD_EEPROM_ADDRESS1 0x52
	#define SPD_EEPROM_ADDRESS2 0x54
	#define SPD_EEPROM_ADDRESS3 0x56
	#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */
	#define CFG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */

	/*
	* IFC Definitions
	*/
	#define CFG_SYS_NOR0_CSPR_EXT (0xf)
	#define CFG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS \
	+ 0x8000000) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CFG_SYS_NOR1_CSPR_EXT (0xf)
	#define CFG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CFG_SYS_NOR_AMASK IFC_AMASK(12810241024)
	/* NOR Flash Timing Params */
	#define CFG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80

	#define CFG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
	FTIM0_NOR_TEADC(0x5) \| \
	FTIM0_NOR_TEAHC(0x5))
	#define CFG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
	FTIM1_NOR_TRAD_NOR(0x1A) \|\
	FTIM1_NOR_TSEQRAD_NOR(0x13))
	#define CFG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
	FTIM2_NOR_TCH(0x4) \| \
	FTIM2_NOR_TWPH(0x0E) \| \
	FTIM2_NOR_TWP(0x1c))
	#define CFG_SYS_NOR_FTIM3 0x0

	#define CFG_SYS_FLASH_BANKS_LIST {CFG_SYS_FLASH_BASE_PHYS \
	+ 0x8000000, CFG_SYS_FLASH_BASE_PHYS}

	/* NAND Flash on IFC */
	#define CFG_SYS_NAND_BASE 0xff800000
	#define CFG_SYS_NAND_BASE_PHYS (0xf00000000ull \| CFG_SYS_NAND_BASE)

	#define CFG_SYS_NAND_CSPR_EXT (0xf)
	#define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
	\| CSPR_MSEL_NAND /* MSEL = NAND */ \
	\| CSPR_V)
	#define CFG_SYS_NAND_AMASK IFC_AMASK(64*1024)

	#define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
	\| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
	\| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
	\| CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
	\| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
	\| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
	\| CSOR_NAND_PB(128)) /Page Per Block = 128/

	/* ONFI NAND Flash mode0 Timing Params */
	#define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) \| \
	FTIM0_NAND_TWP(0x18) \| \
	FTIM0_NAND_TWCHT(0x07) \| \
	FTIM0_NAND_TWH(0x0a))
	#define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) \| \
	FTIM1_NAND_TWBE(0x39) \| \
	FTIM1_NAND_TRR(0x0e) \| \
	FTIM1_NAND_TRP(0x18))
	#define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) \| \
	FTIM2_NAND_TREH(0x0a) \| \
	FTIM2_NAND_TWHRE(0x1e))
	#define CFG_SYS_NAND_FTIM3 0x0

	#define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE }

	#if defined(CONFIG_MTD_RAW_NAND)
	#define CFG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT
	#define CFG_SYS_CSPR0 CFG_SYS_NAND_CSPR
	#define CFG_SYS_AMASK0 CFG_SYS_NAND_AMASK
	#define CFG_SYS_CSOR0 CFG_SYS_NAND_CSOR
	#define CFG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0
	#define CFG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1
	#define CFG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2
	#define CFG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3
	#define CFG_SYS_CSPR2_EXT CFG_SYS_NOR0_CSPR_EXT
	#define CFG_SYS_CSPR2 CFG_SYS_NOR0_CSPR
	#define CFG_SYS_AMASK2 CFG_SYS_NOR_AMASK
	#define CFG_SYS_CSOR2 CFG_SYS_NOR_CSOR
	#define CFG_SYS_CS2_FTIM0 CFG_SYS_NOR_FTIM0
	#define CFG_SYS_CS2_FTIM1 CFG_SYS_NOR_FTIM1
	#define CFG_SYS_CS2_FTIM2 CFG_SYS_NOR_FTIM2
	#define CFG_SYS_CS2_FTIM3 CFG_SYS_NOR_FTIM3
	#else
	#define CFG_SYS_CSPR0_EXT CFG_SYS_NOR0_CSPR_EXT
	#define CFG_SYS_CSPR0 CFG_SYS_NOR0_CSPR
	#define CFG_SYS_AMASK0 CFG_SYS_NOR_AMASK
	#define CFG_SYS_CSOR0 CFG_SYS_NOR_CSOR
	#define CFG_SYS_CS0_FTIM0 CFG_SYS_NOR_FTIM0
	#define CFG_SYS_CS0_FTIM1 CFG_SYS_NOR_FTIM1
	#define CFG_SYS_CS0_FTIM2 CFG_SYS_NOR_FTIM2
	#define CFG_SYS_CS0_FTIM3 CFG_SYS_NOR_FTIM3
	#define CFG_SYS_CSPR1_EXT CFG_SYS_NAND_CSPR_EXT
	#define CFG_SYS_CSPR1 CFG_SYS_NAND_CSPR
	#define CFG_SYS_AMASK1 CFG_SYS_NAND_AMASK
	#define CFG_SYS_CSOR1 CFG_SYS_NAND_CSOR
	#define CFG_SYS_CS1_FTIM0 CFG_SYS_NAND_FTIM0
	#define CFG_SYS_CS1_FTIM1 CFG_SYS_NAND_FTIM1
	#define CFG_SYS_CS1_FTIM2 CFG_SYS_NAND_FTIM2
	#define CFG_SYS_CS1_FTIM3 CFG_SYS_NAND_FTIM3
	#endif
	#define CFG_SYS_CSPR2_EXT CFG_SYS_NOR1_CSPR_EXT
	#define CFG_SYS_CSPR2 CFG_SYS_NOR1_CSPR
	#define CFG_SYS_AMASK2 CFG_SYS_NOR_AMASK
	#define CFG_SYS_CSOR2 CFG_SYS_NOR_CSOR
	#define CFG_SYS_CS2_FTIM0 CFG_SYS_NOR_FTIM0
	#define CFG_SYS_CS2_FTIM1 CFG_SYS_NOR_FTIM1
	#define CFG_SYS_CS2_FTIM2 CFG_SYS_NOR_FTIM2
	#define CFG_SYS_CS2_FTIM3 CFG_SYS_NOR_FTIM3

	/* CPLD on IFC */
	#define CFG_SYS_CPLD_BASE 0xffdf0000
	#define CFG_SYS_CPLD_BASE_PHYS (0xf00000000ull \| CFG_SYS_CPLD_BASE)
	#define CFG_SYS_CSPR3_EXT (0xf)
	#define CFG_SYS_CSPR3 (CSPR_PHYS_ADDR(CFG_SYS_CPLD_BASE_PHYS) \
	\| CSPR_PORT_SIZE_8 \
	\| CSPR_MSEL_GPCM \
	\| CSPR_V)

	#define CFG_SYS_AMASK3 IFC_AMASK(64 * 1024)
	#define CFG_SYS_CSOR3 0x0

	/* CPLD Timing parameters for IFC CS3 */
	#define CFG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) \| \
	FTIM0_GPCM_TEADC(0x0e) \| \
	FTIM0_GPCM_TEAHC(0x0e))
	#define CFG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) \| \
	FTIM1_GPCM_TRAD(0x1f))
	#define CFG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) \| \
	FTIM2_GPCM_TCH(0x8) \| \
	FTIM2_GPCM_TWP(0x1f))
	#define CFG_SYS_CS3_FTIM3 0x0

	/* I2C */
	#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
	#define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */

	#define I2C_MUX_CH_DEFAULT 0x8
	#define I2C_MUX_CH_VOL_MONITOR 0xa
	#define I2C_MUX_CH_VSC3316_FS 0xc
	#define I2C_MUX_CH_VSC3316_BS 0xd

	/* Voltage monitor on channel 2*/
	#define I2C_VOL_MONITOR_ADDR 0x40
	#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
	#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
	#define I2C_VOL_MONITOR_BUS_V_SHIFT 3

	/* The lowest and highest voltage allowed for T4240RDB */
	#define VDD_MV_MIN 819
	#define VDD_MV_MAX 1212

	/*
	* eSPI - Enhanced SPI
	*/

	/* Qman/Bman */
	#ifndef CONFIG_NOBQFMAN
	#define CFG_SYS_BMAN_NUM_PORTALS 50
	#define CFG_SYS_BMAN_MEM_BASE 0xf4000000
	#define CFG_SYS_BMAN_MEM_PHYS 0xff4000000ull
	#define CFG_SYS_BMAN_MEM_SIZE 0x02000000
	#define CFG_SYS_BMAN_SP_CENA_SIZE 0x4000
	#define CFG_SYS_BMAN_SP_CINH_SIZE 0x1000
	#define CFG_SYS_BMAN_CENA_BASE CFG_SYS_BMAN_MEM_BASE
	#define CFG_SYS_BMAN_CENA_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
	#define CFG_SYS_BMAN_CINH_BASE (CFG_SYS_BMAN_MEM_BASE + \
	CFG_SYS_BMAN_CENA_SIZE)
	#define CFG_SYS_BMAN_CINH_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
	#define CFG_SYS_BMAN_SWP_ISDR_REG 0xE08
	#define CFG_SYS_QMAN_NUM_PORTALS 50
	#define CFG_SYS_QMAN_MEM_BASE 0xf6000000
	#define CFG_SYS_QMAN_MEM_PHYS 0xff6000000ull
	#define CFG_SYS_QMAN_MEM_SIZE 0x02000000
	#define CFG_SYS_QMAN_SP_CINH_SIZE 0x1000
	#define CFG_SYS_QMAN_CENA_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
	#define CFG_SYS_QMAN_CINH_BASE (CFG_SYS_QMAN_MEM_BASE + \
	CFG_SYS_QMAN_CENA_SIZE)
	#define CFG_SYS_QMAN_CINH_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
	#define CFG_SYS_QMAN_SWP_ISDR_REG 0xE08
	#endif /* CONFIG_NOBQFMAN */

	#ifdef CONFIG_SYS_DPAA_FMAN
	#define SGMII_PHY_ADDR1 0x0
	#define SGMII_PHY_ADDR2 0x1
	#define SGMII_PHY_ADDR3 0x2
	#define SGMII_PHY_ADDR4 0x3
	#define SGMII_PHY_ADDR5 0x4
	#define SGMII_PHY_ADDR6 0x5
	#define SGMII_PHY_ADDR7 0x6
	#define SGMII_PHY_ADDR8 0x7
	#define FM1_10GEC1_PHY_ADDR 0x10
	#define FM1_10GEC2_PHY_ADDR 0x11
	#define FM2_10GEC1_PHY_ADDR 0x12
	#define FM2_10GEC2_PHY_ADDR 0x13
	#define CORTINA_PHY_ADDR1 FM1_10GEC1_PHY_ADDR
	#define CORTINA_PHY_ADDR2 FM1_10GEC2_PHY_ADDR
	#define CORTINA_PHY_ADDR3 FM2_10GEC1_PHY_ADDR
	#define CORTINA_PHY_ADDR4 FM2_10GEC2_PHY_ADDR
	#endif

	/*
	* USB
	*/

	#ifdef CONFIG_MMC
	#define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR
	#endif

	#define __USB_PHY_TYPE utmi

	/*
	* T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be
	* 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way
	* interleaving. It can be cacheline, page, bank, superbank.
	* See doc/README.fsl-ddr for details.
	*/
	#ifdef CONFIG_ARCH_T4240
	#define CTRL_INTLV_PREFERED 3way_4KB
	#else
	#define CTRL_INTLV_PREFERED cacheline
	#endif

	#define CFG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:" \
	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
	"bank_intlv=auto;" \
	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
	"netdev=eth0\0" \
	"uboot=" CONFIG_UBOOTPATH "\0" \
	"ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot && " \
	"protect off $ubootaddr +$filesize && " \
	"erase $ubootaddr +$filesize && " \
	"cp.b $loadaddr $ubootaddr $filesize && " \
	"protect on $ubootaddr +$filesize && " \
	"cmp.b $loadaddr $ubootaddr $filesize\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=2000000\0" \
	"ramdiskfile=t4240rdb/ramdisk.uboot\0" \
	"fdtaddr=1e00000\0" \
	"fdtfile=t4240rdb/t4240rdb.dtb\0" \
	"bdev=sda3\0"

	#define HVBOOT \
	"setenv bootargs config-addr=0x60000000; " \
	"bootm 0x01000000 - 0x00f00000"

	#include <asm/fsl_secure_boot.h>

	#endif /* __CONFIG_H */