blob: 11725f778b7dbca3af1b6ac56abdf6c394c663d0 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*/
#include <common.h>
#include <debug_uart.h>
#include <init.h>
#include <vsprintf.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/arch/at91sam9rl.h>
#include <asm/arch/at91sam9rl_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <atmel_lcdc.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/*
* Miscelaneous platform dependent initialisations
*/
#ifdef CONFIG_CMD_NAND
static void at91sam9rlek_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Enable CS3 */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(2),
&smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOD);
/* Configure RDY/BSY */
at91_set_gpio_input(CFG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CFG_SYS_NAND_ENABLE_PIN, 1);
at91_set_A_periph(AT91_PIN_PB4, 0); /* NANDOE */
at91_set_A_periph(AT91_PIN_PB5, 0); /* NANDWE */
}
#endif
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
at91_seriald_hw_init();
}
#endif
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
return 0;
}
#endif
int board_init(void)
{
/* arch number of AT91SAM9RLEK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK;
/* adress of boot parameters */
gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_CMD_NAND
at91sam9rlek_nand_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size(
(void *)CFG_SYS_SDRAM_BASE,
CFG_SYS_SDRAM_SIZE);
return 0;
}