blob: 79e5b870b8129b1a28919861760bc9ffe903241e [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2013-2019 Toradex, Inc.
*
* Configuration settings for the Toradex Colibri iMX6
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <linux/stringify.h>
#include "mx6_common.h"
#include <asm/arch/imx-regs.h>
#include <asm/mach-imx/gpio.h>
#define CFG_MXC_UART_BASE UART1_BASE
/* MMC Configs */
#define CFG_SYS_FSL_ESDHC_ADDR 0
#define CFG_SYS_FSL_USDHC_NUM 2
/* USB Configs */
/* Host */
#define CFG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CFG_MXC_USB_FLAGS 0
/* Command definition */
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(USB, usb, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#undef BOOTENV_RUN_NET_USB_START
#define BOOTENV_RUN_NET_USB_START ""
#define UBOOT_UPDATE \
"uboot_hwpart=1\0" \
"uboot_blk=8a\0" \
"uboot_spl_blk=2\0" \
"set_blkcnt=setexpr blkcnt ${filesize} + 0x1ff && " \
"setexpr blkcnt ${blkcnt} / 0x200\0" \
"update_uboot=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
"mmc write ${loadaddr} ${uboot_blk} ${blkcnt}\0" \
"update_spl=run set_blkcnt && mmc dev 0 ${uboot_hwpart} && " \
"mmc write ${loadaddr} ${uboot_spl_blk} ${blkcnt}\0"
#define MEM_LAYOUT_ENV_SETTINGS \
"bootm_size=0x10000000\0" \
"fdt_addr_r=0x18200000\0" \
"kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"pxefile_addr_r=0x18300000\0" \
"ramdisk_addr_r=0x18400000\0" \
"scriptaddr=0x18280000\0"
#define CFG_EXTRA_ENV_SETTINGS \
BOOTENV \
"boot_script_dhcp=boot.scr\0" \
"console=ttymxc0\0" \
"fdt_board=eval-v3\0" \
MEM_LAYOUT_ENV_SETTINGS \
UBOOT_UPDATE \
"setethupdate=if env exists ethaddr; then; else setenv ethaddr " \
"00:14:2d:00:00:00; fi; tftpboot ${loadaddr} " \
"flash_eth.img && source ${loadaddr}\0" \
"setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; load " \
"${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
"source ${loadaddr}\0" \
"setupdate=run setsdupdate || run setusbupdate || run setethupdate\0" \
"setusbupdate=usb start && setenv interface usb; setenv drive 0; " \
"load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && " \
"source ${loadaddr}\0" \
"splashpos=m,m\0" \
"splashimage=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0"
/* Miscellaneous configurable options */
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CFG_SYS_SDRAM_BASE PHYS_SDRAM
#define CFG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CFG_SYS_INIT_RAM_SIZE IRAM_SIZE
#endif /* __CONFIG_H */