blob: 0b9dde3e0e520dcf0abdf50d7f9dbe8c25277288 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2014 Freescale Semiconductor, Inc.
* Copyright 2020-2023 NXP
*/
/*
* T2080 RDB/PCIe board configuration file
*/
#ifndef __T2080RDB_H
#define __T2080RDB_H
#include <linux/stringify.h>
#define CFG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
/* High Level Configuration Options */
#define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
#ifdef CONFIG_RAMBOOT_PBL
#define RESET_VECTOR_OFFSET 0x27FFC
#define BOOT_PAGE_OFFSET 0x27000
#ifdef CONFIG_MTD_RAW_NAND
#define CFG_SYS_NAND_U_BOOT_SIZE (768 << 10)
#define CFG_SYS_NAND_U_BOOT_DST 0x00200000
#define CFG_SYS_NAND_U_BOOT_START 0x00200000
#endif
#ifdef CONFIG_SPIFLASH
#define CFG_RESET_VECTOR_ADDRESS 0x200FFC
#define CFG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
#define CFG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
#define CFG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
#define CFG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
#endif
#ifdef CONFIG_SDCARD
#define CFG_RESET_VECTOR_ADDRESS 0x200FFC
#define CFG_SYS_MMC_U_BOOT_SIZE (768 << 10)
#define CFG_SYS_MMC_U_BOOT_DST (0x00200000)
#define CFG_SYS_MMC_U_BOOT_START (0x00200000)
#define CFG_SYS_MMC_U_BOOT_OFFS (260 << 10)
#endif
#endif /* CONFIG_RAMBOOT_PBL */
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000)
#define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
(0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CFG_RESET_VECTOR_ADDRESS 0xfffffffc
#endif
#ifndef CFG_RESET_VECTOR_ADDRESS
#define CFG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
/*
* Config the L3 Cache as L3 SRAM
*/
#define CFG_SYS_INIT_L3_ADDR 0xFFFC0000
#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
#define CFG_SYS_DCSRBAR 0xf0000000
#define CFG_SYS_DCSRBAR_PHYS 0xf00000000ull
/*
* DDR Setup
*/
#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE
#define CFG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
#define CTRL_INTLV_PREFERED cacheline
/*
* IFC Definitions
*/
#define CFG_SYS_FLASH_BASE 0xe8000000
#define CFG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CFG_SYS_FLASH_BASE)
#define CFG_SYS_NOR0_CSPR_EXT (0xf)
#define CFG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CFG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
/* NOR Flash Timing Params */
#define CFG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
#define CFG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
FTIM0_NOR_TEADC(0x5) | \
FTIM0_NOR_TEAHC(0x5))
#define CFG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
FTIM1_NOR_TRAD_NOR(0x1A) |\
FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CFG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
FTIM2_NOR_TCH(0x4) | \
FTIM2_NOR_TWPH(0x0E) | \
FTIM2_NOR_TWP(0x1c))
#define CFG_SYS_NOR_FTIM3 0x0
#define CFG_SYS_FLASH_BANKS_LIST {CFG_SYS_FLASH_BASE_PHYS }
/* CPLD on IFC */
#define CFG_SYS_CPLD_BASE 0xffdf0000
#define CFG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CFG_SYS_CPLD_BASE)
#define CFG_SYS_CSPR2_EXT (0xf)
#define CFG_SYS_CSPR2 (CSPR_PHYS_ADDR(CFG_SYS_CPLD_BASE) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_GPCM \
| CSPR_V)
#define CFG_SYS_AMASK2 IFC_AMASK(64*1024)
#define CFG_SYS_CSOR2 0x0
/* CPLD Timing parameters for IFC CS2 */
#define CFG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
FTIM0_GPCM_TEADC(0x0e) | \
FTIM0_GPCM_TEAHC(0x0e))
#define CFG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
FTIM1_GPCM_TRAD(0x1f))
#define CFG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
FTIM2_GPCM_TCH(0x8) | \
FTIM2_GPCM_TWP(0x1f))
#define CFG_SYS_CS2_FTIM3 0x0
/* NAND Flash on IFC */
#define CFG_SYS_NAND_BASE 0xff800000
#define CFG_SYS_NAND_BASE_PHYS (0xf00000000ull | CFG_SYS_NAND_BASE)
#define CFG_SYS_NAND_CSPR_EXT (0xf)
#define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
| CSPR_MSEL_NAND /* MSEL = NAND */ \
| CSPR_V)
#define CFG_SYS_NAND_AMASK IFC_AMASK(64*1024)
#define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
| CSOR_NAND_PGS_2K /* Page Size = 2K */\
| CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
/* ONFI NAND Flash mode0 Timing Params */
#define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x07) | \
FTIM0_NAND_TWH(0x0a))
#define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
FTIM1_NAND_TWBE(0x39) | \
FTIM1_NAND_TRR(0x0e) | \
FTIM1_NAND_TRP(0x18))
#define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
FTIM2_NAND_TREH(0x0a) | \
FTIM2_NAND_TWHRE(0x1e))
#define CFG_SYS_NAND_FTIM3 0x0
#define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE }
#if defined(CONFIG_MTD_RAW_NAND)
#define CFG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT
#define CFG_SYS_CSPR0 CFG_SYS_NAND_CSPR
#define CFG_SYS_AMASK0 CFG_SYS_NAND_AMASK
#define CFG_SYS_CSOR0 CFG_SYS_NAND_CSOR
#define CFG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0
#define CFG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1
#define CFG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2
#define CFG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3
#define CFG_SYS_CSPR1_EXT CFG_SYS_NOR0_CSPR_EXT
#define CFG_SYS_CSPR1 CFG_SYS_NOR0_CSPR
#define CFG_SYS_AMASK1 CFG_SYS_NOR_AMASK
#define CFG_SYS_CSOR1 CFG_SYS_NOR_CSOR
#define CFG_SYS_CS1_FTIM0 CFG_SYS_NOR_FTIM0
#define CFG_SYS_CS1_FTIM1 CFG_SYS_NOR_FTIM1
#define CFG_SYS_CS1_FTIM2 CFG_SYS_NOR_FTIM2
#define CFG_SYS_CS1_FTIM3 CFG_SYS_NOR_FTIM3
#else
#define CFG_SYS_CSPR0_EXT CFG_SYS_NOR0_CSPR_EXT
#define CFG_SYS_CSPR0 CFG_SYS_NOR0_CSPR
#define CFG_SYS_AMASK0 CFG_SYS_NOR_AMASK
#define CFG_SYS_CSOR0 CFG_SYS_NOR_CSOR
#define CFG_SYS_CS0_FTIM0 CFG_SYS_NOR_FTIM0
#define CFG_SYS_CS0_FTIM1 CFG_SYS_NOR_FTIM1
#define CFG_SYS_CS0_FTIM2 CFG_SYS_NOR_FTIM2
#define CFG_SYS_CS0_FTIM3 CFG_SYS_NOR_FTIM3
#define CFG_SYS_CSPR1_EXT CFG_SYS_NAND_CSPR_EXT
#define CFG_SYS_CSPR1 CFG_SYS_NAND_CSPR
#define CFG_SYS_AMASK1 CFG_SYS_NAND_AMASK
#define CFG_SYS_CSOR1 CFG_SYS_NAND_CSOR
#define CFG_SYS_CS1_FTIM0 CFG_SYS_NAND_FTIM0
#define CFG_SYS_CS1_FTIM1 CFG_SYS_NAND_FTIM1
#define CFG_SYS_CS1_FTIM2 CFG_SYS_NAND_FTIM2
#define CFG_SYS_CS1_FTIM3 CFG_SYS_NAND_FTIM3
#endif
/* define to use L1 as initial stack */
#define CFG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
#define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
/* The assembler doesn't like typecast */
#define CFG_SYS_INIT_RAM_ADDR_PHYS \
((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CFG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CFG_SYS_INIT_RAM_SIZE 0x00004000
#define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* Serial Port
*/
#if !CONFIG_IS_ENABLED(DM_SERIAL)
#define CFG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#endif
#define CFG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CFG_SYS_NS16550_COM1 (CFG_SYS_CCSRBAR+0x11C500)
#define CFG_SYS_NS16550_COM2 (CFG_SYS_CCSRBAR+0x11C600)
#define CFG_SYS_NS16550_COM3 (CFG_SYS_CCSRBAR+0x11D500)
#define CFG_SYS_NS16550_COM4 (CFG_SYS_CCSRBAR+0x11D600)
/*
* I2C
*/
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
#define I2C_MUX_CH_DEFAULT 0x8
#define I2C_MUX_CH_VOL_MONITOR 0xa
/* The lowest and highest voltage allowed for T208xRDB */
#define VDD_MV_MIN 819
#define VDD_MV_MAX 1212
/*
* RapidIO
*/
#define CFG_SYS_SRIO1_MEM_VIRT 0xa0000000
#define CFG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
#define CFG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
#define CFG_SYS_SRIO2_MEM_VIRT 0xb0000000
#define CFG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
#define CFG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
/*
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
#define CFG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
/* slave core release by master*/
#define CFG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
#define CFG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
/*
* SRIO_PCIE_BOOT - SLAVE
*/
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
#define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
#define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
(0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif
/*
* eSPI - Enhanced SPI
*/
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CFG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CFG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#define CFG_SYS_PCIE1_IO_VIRT 0xf8000000
#define CFG_SYS_PCIE1_IO_PHYS 0xff8000000ull
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#define CFG_SYS_PCIE2_MEM_VIRT 0xa0000000
#define CFG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
#define CFG_SYS_PCIE2_IO_VIRT 0xf8010000
#define CFG_SYS_PCIE2_IO_PHYS 0xff8010000ull
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CFG_SYS_PCIE3_MEM_VIRT 0xb0000000
#define CFG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
/* controller 4, Base address 203000 */
#define CFG_SYS_PCIE4_MEM_VIRT 0xc0000000
#define CFG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
#define CFG_SYS_BMAN_NUM_PORTALS 18
#define CFG_SYS_BMAN_MEM_BASE 0xf4000000
#define CFG_SYS_BMAN_MEM_PHYS 0xff4000000ull
#define CFG_SYS_BMAN_MEM_SIZE 0x02000000
#define CFG_SYS_BMAN_SP_CENA_SIZE 0x4000
#define CFG_SYS_BMAN_SP_CINH_SIZE 0x1000
#define CFG_SYS_BMAN_CENA_BASE CFG_SYS_BMAN_MEM_BASE
#define CFG_SYS_BMAN_CENA_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
#define CFG_SYS_BMAN_CINH_BASE (CFG_SYS_BMAN_MEM_BASE + \
CFG_SYS_BMAN_CENA_SIZE)
#define CFG_SYS_BMAN_CINH_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
#define CFG_SYS_BMAN_SWP_ISDR_REG 0xE08
#define CFG_SYS_QMAN_NUM_PORTALS 18
#define CFG_SYS_QMAN_MEM_BASE 0xf6000000
#define CFG_SYS_QMAN_MEM_PHYS 0xff6000000ull
#define CFG_SYS_QMAN_MEM_SIZE 0x02000000
#define CFG_SYS_QMAN_SP_CINH_SIZE 0x1000
#define CFG_SYS_QMAN_CENA_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
#define CFG_SYS_QMAN_CINH_BASE (CFG_SYS_QMAN_MEM_BASE + \
CFG_SYS_QMAN_CENA_SIZE)
#define CFG_SYS_QMAN_CINH_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
#define CFG_SYS_QMAN_SWP_ISDR_REG 0xE08
#endif /* CONFIG_NOBQFMAN */
#ifdef CONFIG_SYS_DPAA_FMAN
#define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */
#define RGMII_PHY2_ADDR 0x02
#define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */
#define CORTINA_PHY_ADDR2 0x0d
/* Aquantia AQ1202 10G Base-T used by board revisions up to C */
#define FM1_10GEC3_PHY_ADDR 0x00
#define FM1_10GEC4_PHY_ADDR 0x01
/* Aquantia AQR113C 10G Base-T used by board revisions D and up */
#define AQR113C_PHY_ADDR1 0x00
#define AQR113C_PHY_ADDR2 0x08
#endif
/*
* USB
*/
/*
* SDHC
*/
#ifdef CONFIG_MMC
#define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR
#endif
/*
* Dynamic MTD Partition support with mtdparts
*/
/*
* Environment
*/
/*
* Miscellaneous configurable options
*/
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
/*
* Environment Configuration
*/
#define __USB_PHY_TYPE utmi
#define CFG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:" \
"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
"bank_intlv=auto;" \
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
"netdev=eth0\0" \
"uboot=" CONFIG_UBOOTPATH "\0" \
"ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \
"tftpflash=tftpboot $loadaddr $uboot && " \
"protect off $ubootaddr +$filesize && " \
"erase $ubootaddr +$filesize && " \
"cp.b $loadaddr $ubootaddr $filesize && " \
"protect on $ubootaddr +$filesize && " \
"cmp.b $loadaddr $ubootaddr $filesize\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=t2080rdb/ramdisk.uboot\0" \
"fdtaddr=1e00000\0" \
"fdtfile=t2080rdb/t2080rdb.dtb\0" \
"bdev=sda3\0"
/*
* For emulation this causes u-boot to jump to the start of the
* proof point app code automatically
*/
#define PROOF_POINTS \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"cpu 1 release 0x29000000 - - -;" \
"cpu 2 release 0x29000000 - - -;" \
"cpu 3 release 0x29000000 - - -;" \
"cpu 4 release 0x29000000 - - -;" \
"cpu 5 release 0x29000000 - - -;" \
"cpu 6 release 0x29000000 - - -;" \
"cpu 7 release 0x29000000 - - -;" \
"go 0x29000000"
#define HVBOOT \
"setenv bootargs config-addr=0x60000000; " \
"bootm 0x01000000 - 0x00f00000"
#define ALU \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"cpu 1 release 0x01000000 - - -;" \
"cpu 2 release 0x01000000 - - -;" \
"cpu 3 release 0x01000000 - - -;" \
"cpu 4 release 0x01000000 - - -;" \
"cpu 5 release 0x01000000 - - -;" \
"cpu 6 release 0x01000000 - - -;" \
"cpu 7 release 0x01000000 - - -;" \
"go 0x01000000"
#include <asm/fsl_secure_boot.h>
#endif /* __T2080RDB_H */