| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2018 Cisco Systems, Inc. |
| * |
| * Author: Thomas Fitzsimmons <fitzsim@fitzsim.org> |
| */ |
| |
| #include <asm/global_data.h> |
| #include <asm/io.h> |
| #include <command.h> |
| #include <config.h> |
| #include <dm.h> |
| #include <errno.h> |
| #include <fdtdec.h> |
| #include <linux/bitops.h> |
| #include <linux/delay.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <spi.h> |
| #include <time.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define SPBR_MIN 8 |
| #define BITS_PER_WORD 8 |
| |
| #define NUM_TXRAM 32 |
| #define NUM_RXRAM 32 |
| #define NUM_CDRAM 16 |
| |
| /* hif_mspi register structure. */ |
| struct bcmstb_hif_mspi_regs { |
| u32 spcr0_lsb; /* 0x000 */ |
| u32 spcr0_msb; /* 0x004 */ |
| u32 spcr1_lsb; /* 0x008 */ |
| u32 spcr1_msb; /* 0x00c */ |
| u32 newqp; /* 0x010 */ |
| u32 endqp; /* 0x014 */ |
| u32 spcr2; /* 0x018 */ |
| u32 reserved0; /* 0x01c */ |
| u32 mspi_status; /* 0x020 */ |
| u32 cptqp; /* 0x024 */ |
| u32 spcr3; /* 0x028 */ |
| u32 revision; /* 0x02c */ |
| u32 reserved1[4]; /* 0x030 */ |
| u32 txram[NUM_TXRAM]; /* 0x040 */ |
| u32 rxram[NUM_RXRAM]; /* 0x0c0 */ |
| u32 cdram[NUM_CDRAM]; /* 0x140 */ |
| u32 write_lock; /* 0x180 */ |
| }; |
| |
| /* hif_mspi masks. */ |
| #define HIF_MSPI_SPCR2_CONT_AFTER_CMD_MASK 0x00000080 |
| #define HIF_MSPI_SPCR2_SPE_MASK 0x00000040 |
| #define HIF_MSPI_SPCR2_SPIFIE_MASK 0x00000020 |
| #define HIF_MSPI_WRITE_LOCK_WRITE_LOCK_MASK 0x00000001 |
| |
| /* bspi offsets. */ |
| #define BSPI_MAST_N_BOOT_CTRL 0x008 |
| |
| /* bspi_raf is not used in this driver. */ |
| |
| /* hif_spi_intr2 offsets and masks. */ |
| #define HIF_SPI_INTR2_CPU_CLEAR 0x08 |
| #define HIF_SPI_INTR2_CPU_MASK_SET 0x10 |
| #define HIF_SPI_INTR2_CPU_MASK_CLEAR 0x14 |
| #define HIF_SPI_INTR2_CPU_SET_MSPI_DONE_MASK 0x00000020 |
| |
| /* SPI transfer timeout in milliseconds. */ |
| #define HIF_MSPI_WAIT 10 |
| |
| enum bcmstb_base_type { |
| HIF_MSPI, |
| BSPI, |
| HIF_SPI_INTR2, |
| CS_REG, |
| BASE_LAST, |
| }; |
| |
| struct bcmstb_spi_plat { |
| void *base[4]; |
| }; |
| |
| struct bcmstb_spi_priv { |
| struct bcmstb_hif_mspi_regs *regs; |
| void *bspi; |
| void *hif_spi_intr2; |
| void *cs_reg; |
| int default_cs; |
| int curr_cs; |
| uint tx_slot; |
| uint rx_slot; |
| u8 saved_cmd[NUM_CDRAM]; |
| uint saved_cmd_len; |
| void *saved_din_addr; |
| }; |
| |
| static int bcmstb_spi_of_to_plat(struct udevice *bus) |
| { |
| struct bcmstb_spi_plat *plat = dev_get_plat(bus); |
| const void *fdt = gd->fdt_blob; |
| int node = dev_of_offset(bus); |
| int ret = 0; |
| int i = 0; |
| struct fdt_resource resource = { 0 }; |
| char *names[BASE_LAST] = { "hif_mspi", "bspi", "hif_spi_intr2", |
| "cs_reg" }; |
| const phys_addr_t defaults[BASE_LAST] = { BCMSTB_HIF_MSPI_BASE, |
| BCMSTB_BSPI_BASE, |
| BCMSTB_HIF_SPI_INTR2, |
| BCMSTB_CS_REG }; |
| |
| for (i = 0; i < BASE_LAST; i++) { |
| plat->base[i] = (void *)defaults[i]; |
| |
| ret = fdt_get_named_resource(fdt, node, "reg", "reg-names", |
| names[i], &resource); |
| if (ret) { |
| printf("%s: Assuming BCMSTB SPI %s address 0x0x%p\n", |
| __func__, names[i], (void *)defaults[i]); |
| } else { |
| plat->base[i] = (void *)resource.start; |
| debug("BCMSTB SPI %s address: 0x0x%p\n", |
| names[i], (void *)plat->base[i]); |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void bcmstb_spi_hw_set_parms(struct bcmstb_spi_priv *priv) |
| { |
| writel(SPBR_MIN, &priv->regs->spcr0_lsb); |
| writel(BITS_PER_WORD << 2 | SPI_MODE_3, &priv->regs->spcr0_msb); |
| } |
| |
| static void bcmstb_spi_enable_interrupt(void *base, u32 mask) |
| { |
| void *reg = base + HIF_SPI_INTR2_CPU_MASK_CLEAR; |
| |
| writel(readl(reg) | mask, reg); |
| readl(reg); |
| } |
| |
| static void bcmstb_spi_disable_interrupt(void *base, u32 mask) |
| { |
| void *reg = base + HIF_SPI_INTR2_CPU_MASK_SET; |
| |
| writel(readl(reg) | mask, reg); |
| readl(reg); |
| } |
| |
| static void bcmstb_spi_clear_interrupt(void *base, u32 mask) |
| { |
| void *reg = base + HIF_SPI_INTR2_CPU_CLEAR; |
| |
| writel(readl(reg) | mask, reg); |
| readl(reg); |
| } |
| |
| static int bcmstb_spi_probe(struct udevice *bus) |
| { |
| struct bcmstb_spi_plat *plat = dev_get_plat(bus); |
| struct bcmstb_spi_priv *priv = dev_get_priv(bus); |
| |
| priv->regs = plat->base[HIF_MSPI]; |
| priv->bspi = plat->base[BSPI]; |
| priv->hif_spi_intr2 = plat->base[HIF_SPI_INTR2]; |
| priv->cs_reg = plat->base[CS_REG]; |
| priv->default_cs = 0; |
| priv->curr_cs = -1; |
| priv->tx_slot = 0; |
| priv->rx_slot = 0; |
| memset(priv->saved_cmd, 0, NUM_CDRAM); |
| priv->saved_cmd_len = 0; |
| priv->saved_din_addr = NULL; |
| |
| debug("spi_xfer: tx regs: 0x%p\n", &priv->regs->txram[0]); |
| debug("spi_xfer: rx regs: 0x%p\n", &priv->regs->rxram[0]); |
| |
| /* Disable BSPI. */ |
| writel(1, priv->bspi + BSPI_MAST_N_BOOT_CTRL); |
| readl(priv->bspi + BSPI_MAST_N_BOOT_CTRL); |
| |
| /* Set up interrupts. */ |
| bcmstb_spi_disable_interrupt(priv->hif_spi_intr2, 0xffffffff); |
| bcmstb_spi_clear_interrupt(priv->hif_spi_intr2, 0xffffffff); |
| bcmstb_spi_enable_interrupt(priv->hif_spi_intr2, |
| HIF_SPI_INTR2_CPU_SET_MSPI_DONE_MASK); |
| |
| /* Set up control registers. */ |
| writel(0, &priv->regs->spcr1_lsb); |
| writel(0, &priv->regs->spcr1_msb); |
| writel(0, &priv->regs->newqp); |
| writel(0, &priv->regs->endqp); |
| writel(HIF_MSPI_SPCR2_SPIFIE_MASK, &priv->regs->spcr2); |
| writel(0, &priv->regs->spcr3); |
| |
| bcmstb_spi_hw_set_parms(priv); |
| |
| return 0; |
| } |
| |
| static void bcmstb_spi_submit(struct bcmstb_spi_priv *priv, bool done) |
| { |
| debug("WR NEWQP: %d\n", 0); |
| writel(0, &priv->regs->newqp); |
| |
| debug("WR ENDQP: %d\n", priv->tx_slot - 1); |
| writel(priv->tx_slot - 1, &priv->regs->endqp); |
| |
| if (done) { |
| debug("WR CDRAM[%d]: %02x\n", priv->tx_slot - 1, |
| readl(&priv->regs->cdram[priv->tx_slot - 1]) & ~0x80); |
| writel(readl(&priv->regs->cdram[priv->tx_slot - 1]) & ~0x80, |
| &priv->regs->cdram[priv->tx_slot - 1]); |
| } |
| |
| /* Force chip select first time. */ |
| if (priv->curr_cs != priv->default_cs) { |
| debug("spi_xfer: switching chip select to %d\n", |
| priv->default_cs); |
| writel((readl(priv->cs_reg) & ~0xff) | (1 << priv->default_cs), |
| priv->cs_reg); |
| readl(priv->cs_reg); |
| udelay(10); |
| priv->curr_cs = priv->default_cs; |
| } |
| |
| debug("WR WRITE_LOCK: %02x\n", 1); |
| writel((readl(&priv->regs->write_lock) & |
| ~HIF_MSPI_WRITE_LOCK_WRITE_LOCK_MASK) | 1, |
| &priv->regs->write_lock); |
| readl(&priv->regs->write_lock); |
| |
| debug("WR SPCR2: %02x\n", |
| HIF_MSPI_SPCR2_SPIFIE_MASK | |
| HIF_MSPI_SPCR2_SPE_MASK | |
| HIF_MSPI_SPCR2_CONT_AFTER_CMD_MASK); |
| writel(HIF_MSPI_SPCR2_SPIFIE_MASK | |
| HIF_MSPI_SPCR2_SPE_MASK | |
| HIF_MSPI_SPCR2_CONT_AFTER_CMD_MASK, |
| &priv->regs->spcr2); |
| } |
| |
| static int bcmstb_spi_wait(struct bcmstb_spi_priv *priv) |
| { |
| u32 start_time = get_timer(0); |
| u32 status = readl(&priv->regs->mspi_status); |
| |
| while (!(status & 1)) { |
| if (get_timer(start_time) > HIF_MSPI_WAIT) |
| return -ETIMEDOUT; |
| status = readl(&priv->regs->mspi_status); |
| } |
| |
| writel(readl(&priv->regs->mspi_status) & ~1, &priv->regs->mspi_status); |
| bcmstb_spi_clear_interrupt(priv->hif_spi_intr2, |
| HIF_SPI_INTR2_CPU_SET_MSPI_DONE_MASK); |
| |
| return 0; |
| } |
| |
| static int bcmstb_spi_xfer(struct udevice *dev, unsigned int bitlen, |
| const void *dout, void *din, unsigned long flags) |
| { |
| uint len = bitlen / 8; |
| uint tx_len = len; |
| uint rx_len = len; |
| const u8 *out_bytes = (u8 *)dout; |
| u8 *in_bytes = (u8 *)din; |
| struct udevice *bus = dev_get_parent(dev); |
| struct bcmstb_spi_priv *priv = dev_get_priv(bus); |
| struct bcmstb_hif_mspi_regs *regs = priv->regs; |
| |
| debug("spi_xfer: %d, t: 0x%p, r: 0x%p, f: %lx\n", |
| len, dout, din, flags); |
| debug("spi_xfer: chip select: %x\n", readl(priv->cs_reg) & 0xff); |
| debug("spi_xfer: tx addr: 0x%p\n", ®s->txram[0]); |
| debug("spi_xfer: rx addr: 0x%p\n", ®s->rxram[0]); |
| debug("spi_xfer: cd addr: 0x%p\n", ®s->cdram[0]); |
| |
| if (flags & SPI_XFER_END) { |
| debug("spi_xfer: clearing saved din address: 0x%p\n", |
| priv->saved_din_addr); |
| priv->saved_din_addr = NULL; |
| priv->saved_cmd_len = 0; |
| memset(priv->saved_cmd, 0, NUM_CDRAM); |
| } |
| |
| if (bitlen == 0) |
| return 0; |
| |
| if (bitlen % 8) { |
| printf("%s: Non-byte-aligned transfer\n", __func__); |
| return -EOPNOTSUPP; |
| } |
| |
| if (flags & ~(SPI_XFER_BEGIN | SPI_XFER_END)) { |
| printf("%s: Unsupported flags: %lx\n", __func__, flags); |
| return -EOPNOTSUPP; |
| } |
| |
| if (flags & SPI_XFER_BEGIN) { |
| priv->tx_slot = 0; |
| priv->rx_slot = 0; |
| |
| if (out_bytes && len > NUM_CDRAM) { |
| printf("%s: Unable to save transfer\n", __func__); |
| return -EOPNOTSUPP; |
| } |
| |
| if (out_bytes && !(flags & SPI_XFER_END)) { |
| /* |
| * This is the start of a transmit operation |
| * that will need repeating if the calling |
| * code polls for the result. Save it for |
| * subsequent transmission. |
| */ |
| debug("spi_xfer: saving command: %x, %d\n", |
| out_bytes[0], len); |
| priv->saved_cmd_len = len; |
| memcpy(priv->saved_cmd, out_bytes, priv->saved_cmd_len); |
| } |
| } |
| |
| if (!(flags & (SPI_XFER_BEGIN | SPI_XFER_END))) { |
| if (priv->saved_din_addr == din) { |
| /* |
| * The caller is polling for status. Repeat |
| * the last transmission. |
| */ |
| int ret = 0; |
| |
| debug("spi_xfer: Making recursive call\n"); |
| ret = bcmstb_spi_xfer(dev, priv->saved_cmd_len * 8, |
| priv->saved_cmd, NULL, |
| SPI_XFER_BEGIN); |
| if (ret) { |
| printf("%s: Recursive call failed\n", __func__); |
| return ret; |
| } |
| } else { |
| debug("spi_xfer: saving din address: 0x%p\n", din); |
| priv->saved_din_addr = din; |
| } |
| } |
| |
| while (rx_len > 0) { |
| priv->rx_slot = priv->tx_slot; |
| |
| while (priv->tx_slot < NUM_CDRAM && tx_len > 0) { |
| bcmstb_spi_hw_set_parms(priv); |
| debug("WR TXRAM[%d]: %02x\n", priv->tx_slot, |
| out_bytes ? out_bytes[len - tx_len] : 0xff); |
| writel(out_bytes ? out_bytes[len - tx_len] : 0xff, |
| ®s->txram[priv->tx_slot << 1]); |
| debug("WR CDRAM[%d]: %02x\n", priv->tx_slot, 0x8e); |
| writel(0x8e, ®s->cdram[priv->tx_slot]); |
| priv->tx_slot++; |
| tx_len--; |
| if (!in_bytes) |
| rx_len--; |
| } |
| |
| debug("spi_xfer: early return clauses: %d, %d, %d\n", |
| len <= NUM_CDRAM, |
| !in_bytes, |
| (flags & (SPI_XFER_BEGIN | |
| SPI_XFER_END)) == SPI_XFER_BEGIN); |
| if (len <= NUM_CDRAM && |
| !in_bytes && |
| (flags & (SPI_XFER_BEGIN | SPI_XFER_END)) == SPI_XFER_BEGIN) |
| return 0; |
| |
| bcmstb_spi_submit(priv, tx_len == 0); |
| |
| if (bcmstb_spi_wait(priv) == -ETIMEDOUT) { |
| printf("%s: Timed out\n", __func__); |
| return -ETIMEDOUT; |
| } |
| |
| priv->tx_slot %= NUM_CDRAM; |
| |
| if (in_bytes) { |
| while (priv->rx_slot < NUM_CDRAM && rx_len > 0) { |
| in_bytes[len - rx_len] = |
| readl(®s->rxram[(priv->rx_slot << 1) |
| + 1]) |
| & 0xff; |
| debug("RD RXRAM[%d]: %02x\n", |
| priv->rx_slot, in_bytes[len - rx_len]); |
| priv->rx_slot++; |
| rx_len--; |
| } |
| } |
| } |
| |
| if (flags & SPI_XFER_END) { |
| debug("WR WRITE_LOCK: %02x\n", 0); |
| writel((readl(&priv->regs->write_lock) & |
| ~HIF_MSPI_WRITE_LOCK_WRITE_LOCK_MASK) | 0, |
| &priv->regs->write_lock); |
| readl(&priv->regs->write_lock); |
| } |
| |
| return 0; |
| } |
| |
| static int bcmstb_spi_set_speed(struct udevice *dev, uint speed) |
| { |
| return 0; |
| } |
| |
| static int bcmstb_spi_set_mode(struct udevice *dev, uint mode) |
| { |
| return 0; |
| } |
| |
| static const struct dm_spi_ops bcmstb_spi_ops = { |
| .xfer = bcmstb_spi_xfer, |
| .set_speed = bcmstb_spi_set_speed, |
| .set_mode = bcmstb_spi_set_mode, |
| }; |
| |
| static const struct udevice_id bcmstb_spi_id[] = { |
| { .compatible = "brcm,spi-brcmstb" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(bcmstb_spi) = { |
| .name = "bcmstb_spi", |
| .id = UCLASS_SPI, |
| .of_match = bcmstb_spi_id, |
| .ops = &bcmstb_spi_ops, |
| .of_to_plat = bcmstb_spi_of_to_plat, |
| .probe = bcmstb_spi_probe, |
| .plat_auto = sizeof(struct bcmstb_spi_plat), |
| .priv_auto = sizeof(struct bcmstb_spi_priv), |
| }; |