| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2011-2013 Freescale Semiconductor, Inc. |
| * Copyright 2020-2021 NXP |
| */ |
| |
| /* |
| * T2080/T2081 QDS board configuration file |
| */ |
| |
| #ifndef __T208xQDS_H |
| #define __T208xQDS_H |
| |
| #include <linux/stringify.h> |
| |
| #define CFG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ |
| |
| /* High Level Configuration Options */ |
| |
| #define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define RESET_VECTOR_OFFSET 0x27FFC |
| #define BOOT_PAGE_OFFSET 0x27000 |
| |
| #ifdef CONFIG_MTD_RAW_NAND |
| #define CFG_SYS_NAND_U_BOOT_SIZE (768 << 10) |
| #define CFG_SYS_NAND_U_BOOT_DST 0x00200000 |
| #define CFG_SYS_NAND_U_BOOT_START 0x00200000 |
| #endif |
| |
| #ifdef CONFIG_SPIFLASH |
| #define CFG_RESET_VECTOR_ADDRESS 0x200FFC |
| #define CFG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) |
| #define CFG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) |
| #define CFG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) |
| #define CFG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) |
| #endif |
| |
| #ifdef CONFIG_SDCARD |
| #define CFG_RESET_VECTOR_ADDRESS 0x200FFC |
| #define CFG_SYS_MMC_U_BOOT_SIZE (768 << 10) |
| #define CFG_SYS_MMC_U_BOOT_DST (0x00200000) |
| #define CFG_SYS_MMC_U_BOOT_START (0x00200000) |
| #define CFG_SYS_MMC_U_BOOT_OFFS (260 << 10) |
| #endif |
| |
| #endif /* CONFIG_RAMBOOT_PBL */ |
| |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| /* Set 1M boot space */ |
| #define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000) |
| #define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ |
| (0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) |
| #define CFG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #endif |
| |
| #ifndef CFG_RESET_VECTOR_ADDRESS |
| #define CFG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| /* |
| * Config the L3 Cache as L3 SRAM |
| */ |
| #define CFG_SYS_INIT_L3_ADDR 0xFFFC0000 |
| #define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) |
| |
| #define CFG_SYS_DCSRBAR 0xf0000000 |
| #define CFG_SYS_DCSRBAR_PHYS 0xf00000000ull |
| |
| /* |
| * DDR Setup |
| */ |
| #define CFG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE |
| #define CFG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ |
| #define SPD_EEPROM_ADDRESS1 0x51 |
| #define SPD_EEPROM_ADDRESS2 0x52 |
| #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 |
| #define CTRL_INTLV_PREFERED cacheline |
| |
| /* |
| * IFC Definitions |
| */ |
| #define CFG_SYS_FLASH_BASE 0xe0000000 |
| #define CFG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CFG_SYS_FLASH_BASE) |
| #define CFG_SYS_NOR0_CSPR_EXT (0xf) |
| #define CFG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS \ |
| + 0x8000000) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CFG_SYS_NOR1_CSPR_EXT (0xf) |
| #define CFG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CFG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CFG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| /* NOR Flash Timing Params */ |
| #define CFG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 |
| |
| #define CFG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CFG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1A) |\ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CFG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0x0E) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CFG_SYS_NOR_FTIM3 0x0 |
| |
| #define CFG_SYS_FLASH_BANKS_LIST {CFG_SYS_FLASH_BASE_PHYS \ |
| + 0x8000000, CFG_SYS_FLASH_BASE_PHYS} |
| |
| #define QIXIS_BASE 0xffdf0000 |
| #define QIXIS_LBMAP_SWITCH 6 |
| #define QIXIS_LBMAP_MASK 0x0f |
| #define QIXIS_LBMAP_SHIFT 0 |
| #define QIXIS_LBMAP_DFLTBANK 0x00 |
| #define QIXIS_LBMAP_ALTBANK 0x04 |
| #define QIXIS_LBMAP_NAND 0x09 |
| #define QIXIS_LBMAP_SD 0x00 |
| #define QIXIS_RCW_SRC_NAND 0x104 |
| #define QIXIS_RCW_SRC_SD 0x040 |
| #define QIXIS_RST_CTL_RESET 0x83 |
| #define QIXIS_RST_FORCE_MEM 0x1 |
| #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 |
| #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 |
| #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 |
| #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) |
| |
| #define CFG_SYS_CSPR3_EXT (0xf) |
| #define CFG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| #define CFG_SYS_AMASK3 IFC_AMASK(64 * 1024) |
| #define CFG_SYS_CSOR3 0x0 |
| /* QIXIS Timing parameters for IFC CS3 */ |
| #define CFG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define CFG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ |
| FTIM1_GPCM_TRAD(0x3f)) |
| #define CFG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ |
| FTIM2_GPCM_TCH(0x8) | \ |
| FTIM2_GPCM_TWP(0x1f)) |
| #define CFG_SYS_CS3_FTIM3 0x0 |
| |
| /* NAND Flash on IFC */ |
| #define CFG_SYS_NAND_BASE 0xff800000 |
| #define CFG_SYS_NAND_BASE_PHYS (0xf00000000ull | CFG_SYS_NAND_BASE) |
| |
| #define CFG_SYS_NAND_CSPR_EXT (0xf) |
| #define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CFG_SYS_NAND_AMASK IFC_AMASK(64*1024) |
| |
| #define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ |
| | CSOR_NAND_PGS_2K /* Page Size = 2K */\ |
| | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ |
| | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ |
| |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ |
| FTIM0_NAND_TWP(0x18) | \ |
| FTIM0_NAND_TWCHT(0x07) | \ |
| FTIM0_NAND_TWH(0x0a)) |
| #define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ |
| FTIM1_NAND_TWBE(0x39) | \ |
| FTIM1_NAND_TRR(0x0e) | \ |
| FTIM1_NAND_TRP(0x18)) |
| #define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ |
| FTIM2_NAND_TREH(0x0a) | \ |
| FTIM2_NAND_TWHRE(0x1e)) |
| #define CFG_SYS_NAND_FTIM3 0x0 |
| |
| #define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE } |
| |
| #if defined(CONFIG_MTD_RAW_NAND) |
| #define CFG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT |
| #define CFG_SYS_CSPR0 CFG_SYS_NAND_CSPR |
| #define CFG_SYS_AMASK0 CFG_SYS_NAND_AMASK |
| #define CFG_SYS_CSOR0 CFG_SYS_NAND_CSOR |
| #define CFG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0 |
| #define CFG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1 |
| #define CFG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2 |
| #define CFG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3 |
| #define CFG_SYS_CSPR1_EXT CFG_SYS_NOR0_CSPR_EXT |
| #define CFG_SYS_CSPR1 CFG_SYS_NOR0_CSPR |
| #define CFG_SYS_AMASK1 CFG_SYS_NOR_AMASK |
| #define CFG_SYS_CSOR1 CFG_SYS_NOR_CSOR |
| #define CFG_SYS_CS1_FTIM0 CFG_SYS_NOR_FTIM0 |
| #define CFG_SYS_CS1_FTIM1 CFG_SYS_NOR_FTIM1 |
| #define CFG_SYS_CS1_FTIM2 CFG_SYS_NOR_FTIM2 |
| #define CFG_SYS_CS1_FTIM3 CFG_SYS_NOR_FTIM3 |
| #define CFG_SYS_CSPR2_EXT CFG_SYS_NOR1_CSPR_EXT |
| #define CFG_SYS_CSPR2 CFG_SYS_NOR1_CSPR |
| #define CFG_SYS_AMASK2 CFG_SYS_NOR_AMASK |
| #define CFG_SYS_CSOR2 CFG_SYS_NOR_CSOR |
| #define CFG_SYS_CS2_FTIM0 CFG_SYS_NOR_FTIM0 |
| #define CFG_SYS_CS2_FTIM1 CFG_SYS_NOR_FTIM1 |
| #define CFG_SYS_CS2_FTIM2 CFG_SYS_NOR_FTIM2 |
| #define CFG_SYS_CS2_FTIM3 CFG_SYS_NOR_FTIM3 |
| #else |
| #define CFG_SYS_CSPR0_EXT CFG_SYS_NOR0_CSPR_EXT |
| #define CFG_SYS_CSPR0 CFG_SYS_NOR0_CSPR |
| #define CFG_SYS_AMASK0 CFG_SYS_NOR_AMASK |
| #define CFG_SYS_CSOR0 CFG_SYS_NOR_CSOR |
| #define CFG_SYS_CS0_FTIM0 CFG_SYS_NOR_FTIM0 |
| #define CFG_SYS_CS0_FTIM1 CFG_SYS_NOR_FTIM1 |
| #define CFG_SYS_CS0_FTIM2 CFG_SYS_NOR_FTIM2 |
| #define CFG_SYS_CS0_FTIM3 CFG_SYS_NOR_FTIM3 |
| #define CFG_SYS_CSPR1_EXT CFG_SYS_NOR1_CSPR_EXT |
| #define CFG_SYS_CSPR1 CFG_SYS_NOR1_CSPR |
| #define CFG_SYS_AMASK1 CFG_SYS_NOR_AMASK |
| #define CFG_SYS_CSOR1 CFG_SYS_NOR_CSOR |
| #define CFG_SYS_CS1_FTIM0 CFG_SYS_NOR_FTIM0 |
| #define CFG_SYS_CS1_FTIM1 CFG_SYS_NOR_FTIM1 |
| #define CFG_SYS_CS1_FTIM2 CFG_SYS_NOR_FTIM2 |
| #define CFG_SYS_CS1_FTIM3 CFG_SYS_NOR_FTIM3 |
| #define CFG_SYS_CSPR2_EXT CFG_SYS_NAND_CSPR_EXT |
| #define CFG_SYS_CSPR2 CFG_SYS_NAND_CSPR |
| #define CFG_SYS_AMASK2 CFG_SYS_NAND_AMASK |
| #define CFG_SYS_CSOR2 CFG_SYS_NAND_CSOR |
| #define CFG_SYS_CS2_FTIM0 CFG_SYS_NAND_FTIM0 |
| #define CFG_SYS_CS2_FTIM1 CFG_SYS_NAND_FTIM1 |
| #define CFG_SYS_CS2_FTIM2 CFG_SYS_NAND_FTIM2 |
| #define CFG_SYS_CS2_FTIM3 CFG_SYS_NAND_FTIM3 |
| #endif |
| |
| /* define to use L1 as initial stack */ |
| #define CFG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ |
| #define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf |
| #define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 |
| /* The assembler doesn't like typecast */ |
| #define CFG_SYS_INIT_RAM_ADDR_PHYS \ |
| ((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ |
| CFG_SYS_INIT_RAM_ADDR_PHYS_LOW) |
| #define CFG_SYS_INIT_RAM_SIZE 0x00004000 |
| #define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| /* |
| * Serial Port |
| */ |
| #define CFG_SYS_NS16550_CLK (get_bus_freq(0)/2) |
| #define CFG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| #define CFG_SYS_NS16550_COM1 (CFG_SYS_CCSRBAR+0x11C500) |
| #define CFG_SYS_NS16550_COM2 (CFG_SYS_CCSRBAR+0x11C600) |
| #define CFG_SYS_NS16550_COM3 (CFG_SYS_CCSRBAR+0x11D500) |
| #define CFG_SYS_NS16550_COM4 (CFG_SYS_CCSRBAR+0x11D600) |
| |
| /* |
| * I2C |
| */ |
| |
| #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ |
| #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ |
| #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| |
| #define I2C_MUX_CH_VOL_MONITOR 0xa |
| |
| /* Voltage monitor on channel 2*/ |
| #define I2C_VOL_MONITOR_ADDR 0x40 |
| #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 |
| #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 |
| #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 |
| |
| /* The lowest and highest voltage allowed for T208xQDS */ |
| #define VDD_MV_MIN 819 |
| #define VDD_MV_MAX 1212 |
| |
| /* |
| * RapidIO |
| */ |
| #define CFG_SYS_SRIO1_MEM_VIRT 0xa0000000 |
| #define CFG_SYS_SRIO1_MEM_PHYS 0xc20000000ull |
| #define CFG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ |
| #define CFG_SYS_SRIO2_MEM_VIRT 0xb0000000 |
| #define CFG_SYS_SRIO2_MEM_PHYS 0xc30000000ull |
| #define CFG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ |
| /* |
| * for slave u-boot IMAGE instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull |
| #define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull |
| #define CFG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ |
| #define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull |
| /* |
| * for slave UCODE and ENV instored in master memory space, |
| * PHYS must be aligned based on the SIZE |
| */ |
| #define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull |
| #define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull |
| #define CFG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ |
| |
| /* slave core release by master*/ |
| #define CFG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 |
| #define CFG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ |
| |
| /* |
| * SRIO_PCIE_BOOT - SLAVE |
| */ |
| #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE |
| #define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 |
| #define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ |
| (0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) |
| #endif |
| |
| /* |
| * eSPI - Enhanced SPI |
| */ |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| /* controller 1, direct to uli, tgtid 3, Base address 20000 */ |
| #define CFG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #define CFG_SYS_PCIE1_MEM_PHYS 0xc00000000ull |
| #define CFG_SYS_PCIE1_IO_VIRT 0xf8000000 |
| #define CFG_SYS_PCIE1_IO_PHYS 0xff8000000ull |
| |
| /* controller 2, Slot 2, tgtid 2, Base address 201000 */ |
| #define CFG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #define CFG_SYS_PCIE2_MEM_PHYS 0xc20000000ull |
| #define CFG_SYS_PCIE2_IO_VIRT 0xf8010000 |
| #define CFG_SYS_PCIE2_IO_PHYS 0xff8010000ull |
| |
| /* controller 3, Slot 1, tgtid 1, Base address 202000 */ |
| #define CFG_SYS_PCIE3_MEM_VIRT 0xb0000000 |
| #define CFG_SYS_PCIE3_MEM_PHYS 0xc30000000ull |
| |
| /* controller 4, Base address 203000 */ |
| #define CFG_SYS_PCIE4_MEM_VIRT 0xc0000000 |
| #define CFG_SYS_PCIE4_MEM_PHYS 0xc40000000ull |
| |
| /* Qman/Bman */ |
| #ifndef CONFIG_NOBQFMAN |
| #define CFG_SYS_BMAN_NUM_PORTALS 18 |
| #define CFG_SYS_BMAN_MEM_BASE 0xf4000000 |
| #define CFG_SYS_BMAN_MEM_PHYS 0xff4000000ull |
| #define CFG_SYS_BMAN_MEM_SIZE 0x02000000 |
| #define CFG_SYS_BMAN_SP_CENA_SIZE 0x4000 |
| #define CFG_SYS_BMAN_SP_CINH_SIZE 0x1000 |
| #define CFG_SYS_BMAN_CENA_BASE CFG_SYS_BMAN_MEM_BASE |
| #define CFG_SYS_BMAN_CENA_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CFG_SYS_BMAN_CINH_BASE (CFG_SYS_BMAN_MEM_BASE + \ |
| CFG_SYS_BMAN_CENA_SIZE) |
| #define CFG_SYS_BMAN_CINH_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CFG_SYS_BMAN_SWP_ISDR_REG 0xE08 |
| #define CFG_SYS_QMAN_NUM_PORTALS 18 |
| #define CFG_SYS_QMAN_MEM_BASE 0xf6000000 |
| #define CFG_SYS_QMAN_MEM_PHYS 0xff6000000ull |
| #define CFG_SYS_QMAN_MEM_SIZE 0x02000000 |
| #define CFG_SYS_QMAN_SP_CINH_SIZE 0x1000 |
| #define CFG_SYS_QMAN_CENA_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CFG_SYS_QMAN_CINH_BASE (CFG_SYS_QMAN_MEM_BASE + \ |
| CFG_SYS_QMAN_CENA_SIZE) |
| #define CFG_SYS_QMAN_CINH_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CFG_SYS_QMAN_SWP_ISDR_REG 0xE08 |
| #endif /* CONFIG_NOBQFMAN */ |
| |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| #define RGMII_PHY1_ADDR 0x1 |
| #define RGMII_PHY2_ADDR 0x2 |
| #define FM1_10GEC1_PHY_ADDR 0x3 |
| #define SGMII_CARD_PORT1_PHY_ADDR 0x1C |
| #define SGMII_CARD_PORT2_PHY_ADDR 0x1D |
| #define SGMII_CARD_PORT3_PHY_ADDR 0x1E |
| #define SGMII_CARD_PORT4_PHY_ADDR 0x1F |
| #endif |
| |
| /* |
| * USB |
| */ |
| |
| /* |
| * SDHC |
| */ |
| #ifdef CONFIG_MMC |
| #define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR |
| #endif |
| |
| /* |
| * Dynamic MTD Partition support with mtdparts |
| */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| #define __USB_PHY_TYPE utmi |
| |
| #define CFG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:" \ |
| "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ |
| "bank_intlv=auto;" \ |
| "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ |
| "netdev=eth0\0" \ |
| "uboot=" CONFIG_UBOOTPATH "\0" \ |
| "ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot && " \ |
| "protect off $ubootaddr +$filesize && " \ |
| "erase $ubootaddr +$filesize && " \ |
| "cp.b $loadaddr $ubootaddr $filesize && " \ |
| "protect on $ubootaddr +$filesize && " \ |
| "cmp.b $loadaddr $ubootaddr $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=t2080qds/ramdisk.uboot\0" \ |
| "fdtaddr=1e00000\0" \ |
| "fdtfile=t2080qds/t2080qds.dtb\0" \ |
| "bdev=sda3\0" |
| |
| /* |
| * For emulation this causes u-boot to jump to the start of the |
| * proof point app code automatically |
| */ |
| #define PROOF_POINTS \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "cpu 1 release 0x29000000 - - -;" \ |
| "cpu 2 release 0x29000000 - - -;" \ |
| "cpu 3 release 0x29000000 - - -;" \ |
| "cpu 4 release 0x29000000 - - -;" \ |
| "cpu 5 release 0x29000000 - - -;" \ |
| "cpu 6 release 0x29000000 - - -;" \ |
| "cpu 7 release 0x29000000 - - -;" \ |
| "go 0x29000000" |
| |
| #define HVBOOT \ |
| "setenv bootargs config-addr=0x60000000; " \ |
| "bootm 0x01000000 - 0x00f00000" |
| |
| #define ALU \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "cpu 1 release 0x01000000 - - -;" \ |
| "cpu 2 release 0x01000000 - - -;" \ |
| "cpu 3 release 0x01000000 - - -;" \ |
| "cpu 4 release 0x01000000 - - -;" \ |
| "cpu 5 release 0x01000000 - - -;" \ |
| "cpu 6 release 0x01000000 - - -;" \ |
| "cpu 7 release 0x01000000 - - -;" \ |
| "go 0x01000000" |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __T208xQDS_H */ |
