blob: f7e9b74f57827d3a60c2a7f29797d550941e2404 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0+
#
# Copyright (C) 2019, Pascal Linder <pascal.linder@edu.hefr.ch>
config VENDOR_KM
bool
help
Selected by any KM board to have additional configurations.
if VENDOR_KM
menu "KM Board Setup"
config SYS_I2C_INIT_BOARD
def_bool y if ARM
config HUSH_INIT_VAR
def_bool y
config KM_PNVRAM
hex "Pseudo RAM"
default 0x80000
depends on !ARCH_SOCFPGA
help
Start address of the pseudo non-volatile RAM for application.
config KM_PHRAM
hex "Physical RAM"
default 0x17F000 if ARM && !ARCH_LS1021A
default 0x100000 if PPC || ARCH_LS1021A
depends on !ARCH_SOCFPGA
help
Start address of the physical RAM, which is the mounted /var folder.
config KM_RESERVED_PRAM
hex "Reserved RAM"
default 0x0 if MPC83xx
default 0x1000 if MPC85xx || ARCH_LS1021A
depends on !ARCH_SOCFPGA
help
Reserved physical RAM area at the end of memory for special purposes.
config KM_CRAMFS_ADDR
hex "CRAMFS Address"
default 0x83000000 if ARCH_LS1021A
default 0x3000000
depends on !ARCH_SOCFPGA
help
Start address of the CRAMFS containing the Linux kernel.
config KM_KERNEL_ADDR
hex "Kernel Load Address"
default 0x82000000 if ARCH_LS1021A
default 0x2000000
help
Address where to load Linux kernel in RAM.
config KM_FDT_ADDR
hex "FDT Load Address"
default 0x82FC0000 if ARCH_LS1021A
default 0x2FC0000
help
Address where to load flattened device tree in RAM.
config SYS_PAX_BASE
hex "PAX IFC Base Address"
default 0x78000000
depends on ARCH_LS1021A
help
IFC Base Address for PAXx FPGA.
config SYS_CLIPS_BASE
hex "CLIPS IFC Base Address"
default 0x78000000
depends on ARCH_LS1021A
help
IFC Base Address for CLIPS FPGA.
config KM_COMMON_ETH_INIT
bool "Common Ethernet Initialization"
default y if MPC83xx
default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A
help
Use the Ethernet initialization implemented in common code that
detects if a Piggy board is present.
config PIGGY_MAC_ADDRESS_OFFSET
int "Piggy Address Offset"
default 0
help
MAC address offset for the Piggy board.
config KM_MVEXTSW_ADDR
hex "Marvell Switch Address"
depends on MV88E6352_SWITCH
default 0x10
help
Address of external Marvell switch.
config KM_IVM_BUS
int "IVM I2C Bus"
default 0 if ARCH_SOCFPGA
default 1 if PPC || ARCH_LS1021A
help
Identifier number of I2C bus, where the inventory EEPROM is connected to.
config SYS_IVM_EEPROM_ADR
hex "IVM I2C Address"
default 0x50
help
I2C address of the EEPROM containing the inventory.
config SYS_IVM_EEPROM_MAX_LEN
hex "IVM Length"
default 0x400
help
Maximum length of inventory in EEPROM.
config SYS_IVM_EEPROM_PAGE_LEN
hex "IVM Page Size"
default 0x100
help
Page size of inventory in EEPROM.
config PG_WCOM_UBOOT_UPDATE_SUPPORTED
bool "Enable U-Boot Field Fail-Safe Update Functionality"
select EVENT
help
Indicates that field fail-safe u-boot update is supported.
This functionality works only for designs that are booting
from parallel NOR flash.
config PG_WCOM_UBOOT_BOOTPACKAGE
bool "U-Boot Is Part Of Factory Boot-Package Image"
help
Indicates that u-boot will be a part of the factory programmed
boot-package image.
Has to be set for original u-boot programmed at factory.
config PG_WCOM_UBOOT_UPDATE_TEXT_BASE
hex "Text Base For U-Boot Programmed Outside Factory"
default 0xFFFFFFFF
help
Text base of an updated u-boot that is not factory programmed but
later when the unit is rolled out on the field.
Has to be set for original u-boot programmed at factory.
config PG_WCOM_UBOOT_UPDATE
bool "U-Boot Is Part Of Factory Boot-Package Image"
help
Indicates that u-boot will be a part of the embedded software and
programmed at field.
Has to be set for updated u-boot version programmed at field.
source "board/keymile/km83xx/Kconfig"
source "board/keymile/kmcent2/Kconfig"
source "board/keymile/pg-wcom-ls102xa/Kconfig"
endmenu
endif