board/data_modul/imx8mp_edm_sbc/imx8mp_data_modul_edm_sbc.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright 2022 Marek Vasut <marex@denx.de>
 */

#include <common.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8mp_pins.h>
#include <asm/io.h>
#include <dm.h>
#include <dm/device-internal.h>
#include <env.h>
#include <env_internal.h>
#include <linux/bitfield.h>
#include <malloc.h>
#include <net.h>
#include <spl.h>

#include "../common/common.h"

DECLARE_GLOBAL_DATA_PTR;

static void dmo_setup_second_mac_address(void)
{
	u8 enetaddr[6];
	int ret;

	/* In case 'eth1addr' is already set in environment, do nothing. */
	ret = eth_env_get_enetaddr_by_index("eth", 1, enetaddr);
	if (ret)	/* valid 'eth1addr' is already set */
		return;

	/* Read 'ethaddr' from environment and validate. */
	ret = eth_env_get_enetaddr_by_index("eth", 0, enetaddr);
	if (!ret)	/* 'ethaddr' in environment is not valid, stop */
		return;

	/* Set 'eth1addr' as 'ethaddr' + 1 */
	enetaddr[5]++;

	eth_env_set_enetaddr_by_index("eth", 1, enetaddr);
}

enum env_location env_get_location(enum env_operation op, int prio)
{
	/* Environment is always in eMMC boot partitions */
	return prio ? ENVL_UNKNOWN : ENVL_MMC;
}

int board_init(void)
{
	return 0;
}

int board_late_init(void)
{
	struct udevice *dev;
	int ret;

	dmo_setup_boot_device();
	dmo_setup_mac_address();
	dmo_setup_second_mac_address();

	ret = uclass_get_device_by_name(UCLASS_MISC, "usb-hub@2c", &dev);
	if (ret)
		printf("Error bringing up USB hub (%d)\n", ret);

	return 0;
}

int fdtdec_board_setup(const void *fdt_blob)
{
	const void __iomem *mux = (void __iomem *)IOMUXC_BASE_ADDR +
		FIELD_GET(MUX_CTRL_OFS_MASK, MX8MP_PAD_ENET_MDC__ENET_QOS_MDC);
	const char *phy_compat = "ethernet-phy-ieee802.3-c22";
	bool is_bcmphy;
	int phy_node;
	int ret;

	/* Do nothing if not i.MX8MP eDM SBC */
	ret = fdt_node_check_compatible(fdt_blob, 0, "dmo,imx8mp-data-modul-edm-sbc");
	if (ret)
		return 0;

	/*
	 * If GPIO1_16 RGMII_MDC is HIGH, then R390 is populated.
	 * R390 is populated only on boards with AR8031 PHY.
	 *
	 * If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down
	 * is the dominant pull resistor. This is the case on boards
	 * with BCM54213PE PHY.
	 */
	setbits_le32(mux, IOMUX_CONFIG_SION);
	is_bcmphy = !(readl(GPIO1_BASE_ADDR) & BIT(16));
	clrbits_le32(mux, IOMUX_CONFIG_SION);

	phy_node = fdt_node_offset_by_compatible(fdt_blob, -1, phy_compat);
	if (phy_node < 0)
		return 0;

	/*
	 * Update PHY MDC address in control DT based on the populated
	 * PHY type. AR8031 is at address 0, BCM54213PE is at address 1.
	 */
	fdt_setprop_inplace_u32((void *)fdt_blob, phy_node,
				"reg", is_bcmphy ? 1 : 0);

	/* Apply the same modification to EQoS PHY */
	phy_node = fdt_node_offset_by_compatible(fdt_blob, phy_node, phy_compat);
	if (phy_node < 0)
		return 0;

	fdt_setprop_inplace_u32((void *)fdt_blob, phy_node,
				"reg", is_bcmphy ? 1 : 0);

	return 0;
}