| // SPDX-License-Identifier: GPL-2.0+ OR MIT |
| // |
| // Device Tree Source for UniPhier PXs2 SoC |
| // |
| // Copyright (C) 2015-2016 Socionext Inc. |
| // Author: Masahiro Yamada <yamada.masahiro@socionext.com> |
| |
| #include <dt-bindings/gpio/uniphier-gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| compatible = "socionext,uniphier-pxs2"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <0>; |
| clocks = <&sys_clk 32>; |
| enable-method = "psci"; |
| next-level-cache = <&l2>; |
| operating-points-v2 = <&cpu_opp>; |
| #cooling-cells = <2>; |
| }; |
| |
| cpu1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <1>; |
| clocks = <&sys_clk 32>; |
| enable-method = "psci"; |
| next-level-cache = <&l2>; |
| operating-points-v2 = <&cpu_opp>; |
| #cooling-cells = <2>; |
| }; |
| |
| cpu2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <2>; |
| clocks = <&sys_clk 32>; |
| enable-method = "psci"; |
| next-level-cache = <&l2>; |
| operating-points-v2 = <&cpu_opp>; |
| #cooling-cells = <2>; |
| }; |
| |
| cpu3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a9"; |
| reg = <3>; |
| clocks = <&sys_clk 32>; |
| enable-method = "psci"; |
| next-level-cache = <&l2>; |
| operating-points-v2 = <&cpu_opp>; |
| #cooling-cells = <2>; |
| }; |
| }; |
| |
| cpu_opp: opp-table { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| clock-latency-ns = <300>; |
| }; |
| opp-150000000 { |
| opp-hz = /bits/ 64 <150000000>; |
| clock-latency-ns = <300>; |
| }; |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| clock-latency-ns = <300>; |
| }; |
| opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| clock-latency-ns = <300>; |
| }; |
| opp-400000000 { |
| opp-hz = /bits/ 64 <400000000>; |
| clock-latency-ns = <300>; |
| }; |
| opp-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| clock-latency-ns = <300>; |
| }; |
| opp-800000000 { |
| opp-hz = /bits/ 64 <800000000>; |
| clock-latency-ns = <300>; |
| }; |
| opp-1200000000 { |
| opp-hz = /bits/ 64 <1200000000>; |
| clock-latency-ns = <300>; |
| }; |
| }; |
| |
| psci { |
| compatible = "arm,psci-0.2"; |
| method = "smc"; |
| }; |
| |
| clocks { |
| refclk: ref { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <25000000>; |
| }; |
| |
| arm_timer_clk: arm-timer { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <50000000>; |
| }; |
| }; |
| |
| thermal-zones { |
| cpu-thermal { |
| polling-delay-passive = <250>; /* 250ms */ |
| polling-delay = <1000>; /* 1000ms */ |
| thermal-sensors = <&pvtctl>; |
| |
| trips { |
| cpu_crit: cpu-crit { |
| temperature = <95000>; /* 95C */ |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| cpu_alert: cpu-alert { |
| temperature = <85000>; /* 85C */ |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| }; |
| |
| cooling-maps { |
| map { |
| trip = <&cpu_alert>; |
| cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| }; |
| |
| soc { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| interrupt-parent = <&intc>; |
| |
| l2: cache-controller@500c0000 { |
| compatible = "socionext,uniphier-system-cache"; |
| reg = <0x500c0000 0x2000>, <0x503c0100 0x8>, |
| <0x506c0000 0x400>; |
| interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>; |
| cache-unified; |
| cache-size = <(1280 * 1024)>; |
| cache-sets = <512>; |
| cache-line-size = <128>; |
| cache-level = <2>; |
| }; |
| |
| spi0: spi@54006000 { |
| compatible = "socionext,uniphier-scssi"; |
| status = "disabled"; |
| reg = <0x54006000 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi0>; |
| clocks = <&peri_clk 11>; |
| resets = <&peri_rst 11>; |
| }; |
| |
| spi1: spi@54006100 { |
| compatible = "socionext,uniphier-scssi"; |
| status = "disabled"; |
| reg = <0x54006100 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi1>; |
| clocks = <&peri_clk 12>; |
| resets = <&peri_rst 12>; |
| }; |
| |
| serial0: serial@54006800 { |
| compatible = "socionext,uniphier-uart"; |
| status = "disabled"; |
| reg = <0x54006800 0x40>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart0>; |
| clocks = <&peri_clk 0>; |
| resets = <&peri_rst 0>; |
| }; |
| |
| serial1: serial@54006900 { |
| compatible = "socionext,uniphier-uart"; |
| status = "disabled"; |
| reg = <0x54006900 0x40>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| clocks = <&peri_clk 1>; |
| resets = <&peri_rst 1>; |
| }; |
| |
| serial2: serial@54006a00 { |
| compatible = "socionext,uniphier-uart"; |
| status = "disabled"; |
| reg = <0x54006a00 0x40>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| clocks = <&peri_clk 2>; |
| resets = <&peri_rst 2>; |
| }; |
| |
| serial3: serial@54006b00 { |
| compatible = "socionext,uniphier-uart"; |
| status = "disabled"; |
| reg = <0x54006b00 0x40>; |
| interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| clocks = <&peri_clk 3>; |
| resets = <&peri_rst 3>; |
| }; |
| |
| gpio: gpio@55000000 { |
| compatible = "socionext,uniphier-gpio"; |
| reg = <0x55000000 0x200>; |
| interrupt-parent = <&aidet>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pinctrl 0 0 0>, |
| <&pinctrl 96 0 0>; |
| gpio-ranges-group-names = "gpio_range0", |
| "gpio_range1"; |
| ngpios = <232>; |
| socionext,interrupt-ranges = <0 48 16>, <16 154 5>, |
| <21 217 3>; |
| }; |
| |
| audio@56000000 { |
| compatible = "socionext,uniphier-pxs2-aio"; |
| reg = <0x56000000 0x80000>; |
| interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ain1>, |
| <&pinctrl_ain2>, |
| <&pinctrl_ainiec1>, |
| <&pinctrl_aout2>, |
| <&pinctrl_aout3>, |
| <&pinctrl_aoutiec1>, |
| <&pinctrl_aoutiec2>; |
| clock-names = "aio"; |
| clocks = <&sys_clk 40>; |
| reset-names = "aio"; |
| resets = <&sys_rst 40>; |
| #sound-dai-cells = <1>; |
| socionext,syscon = <&soc_glue>; |
| |
| i2s_port0: port@0 { |
| i2s_hdmi: endpoint { |
| }; |
| }; |
| |
| i2s_port1: port@1 { |
| i2s_line: endpoint { |
| }; |
| }; |
| |
| i2s_port2: port@2 { |
| i2s_aux: endpoint { |
| }; |
| }; |
| |
| spdif_port0: port@3 { |
| spdif_hiecout1: endpoint { |
| }; |
| }; |
| |
| spdif_port1: port@4 { |
| spdif_iecout1: endpoint { |
| }; |
| }; |
| |
| comp_spdif_port0: port@5 { |
| comp_spdif_hiecout1: endpoint { |
| }; |
| }; |
| |
| comp_spdif_port1: port@6 { |
| comp_spdif_iecout1: endpoint { |
| }; |
| }; |
| }; |
| |
| i2c0: i2c@58780000 { |
| compatible = "socionext,uniphier-fi2c"; |
| status = "disabled"; |
| reg = <0x58780000 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c0>; |
| clocks = <&peri_clk 4>; |
| resets = <&peri_rst 4>; |
| clock-frequency = <100000>; |
| }; |
| |
| i2c1: i2c@58781000 { |
| compatible = "socionext,uniphier-fi2c"; |
| status = "disabled"; |
| reg = <0x58781000 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| clocks = <&peri_clk 5>; |
| resets = <&peri_rst 5>; |
| clock-frequency = <100000>; |
| }; |
| |
| i2c2: i2c@58782000 { |
| compatible = "socionext,uniphier-fi2c"; |
| status = "disabled"; |
| reg = <0x58782000 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| clocks = <&peri_clk 6>; |
| resets = <&peri_rst 6>; |
| clock-frequency = <100000>; |
| }; |
| |
| i2c3: i2c@58783000 { |
| compatible = "socionext,uniphier-fi2c"; |
| status = "disabled"; |
| reg = <0x58783000 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| clocks = <&peri_clk 7>; |
| resets = <&peri_rst 7>; |
| clock-frequency = <100000>; |
| }; |
| |
| /* chip-internal connection for DMD */ |
| i2c4: i2c@58784000 { |
| compatible = "socionext,uniphier-fi2c"; |
| reg = <0x58784000 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&peri_clk 8>; |
| resets = <&peri_rst 8>; |
| clock-frequency = <400000>; |
| }; |
| |
| /* chip-internal connection for STM */ |
| i2c5: i2c@58785000 { |
| compatible = "socionext,uniphier-fi2c"; |
| reg = <0x58785000 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&peri_clk 9>; |
| resets = <&peri_rst 9>; |
| clock-frequency = <400000>; |
| }; |
| |
| /* chip-internal connection for HDMI */ |
| i2c6: i2c@58786000 { |
| compatible = "socionext,uniphier-fi2c"; |
| reg = <0x58786000 0x80>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&peri_clk 10>; |
| resets = <&peri_rst 10>; |
| clock-frequency = <400000>; |
| }; |
| |
| system_bus: system-bus@58c00000 { |
| compatible = "socionext,uniphier-system-bus"; |
| status = "disabled"; |
| reg = <0x58c00000 0x400>; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_system_bus>; |
| }; |
| |
| smpctrl@59801000 { |
| compatible = "socionext,uniphier-smpctrl"; |
| reg = <0x59801000 0x400>; |
| }; |
| |
| sdctrl: syscon@59810000 { |
| compatible = "socionext,uniphier-pxs2-sdctrl", |
| "simple-mfd", "syscon"; |
| reg = <0x59810000 0x400>; |
| |
| sd_clk: clock-controller { |
| compatible = "socionext,uniphier-pxs2-sd-clock"; |
| #clock-cells = <1>; |
| }; |
| |
| sd_rst: reset-controller { |
| compatible = "socionext,uniphier-pxs2-sd-reset"; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| syscon@59820000 { |
| compatible = "socionext,uniphier-pxs2-perictrl", |
| "simple-mfd", "syscon"; |
| reg = <0x59820000 0x200>; |
| |
| peri_clk: clock-controller { |
| compatible = "socionext,uniphier-pxs2-peri-clock"; |
| #clock-cells = <1>; |
| }; |
| |
| peri_rst: reset-controller { |
| compatible = "socionext,uniphier-pxs2-peri-reset"; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| emmc: mmc@5a000000 { |
| compatible = "socionext,uniphier-sd-v3.1.1"; |
| status = "disabled"; |
| reg = <0x5a000000 0x800>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_emmc>; |
| clocks = <&sd_clk 1>; |
| reset-names = "host", "hw"; |
| resets = <&sd_rst 1>, <&sd_rst 6>; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| cap-mmc-hw-reset; |
| non-removable; |
| }; |
| |
| sd: mmc@5a400000 { |
| compatible = "socionext,uniphier-sd-v3.1.1"; |
| status = "disabled"; |
| reg = <0x5a400000 0x800>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default", "uhs"; |
| pinctrl-0 = <&pinctrl_sd>; |
| pinctrl-1 = <&pinctrl_sd_uhs>; |
| clocks = <&sd_clk 0>; |
| reset-names = "host"; |
| resets = <&sd_rst 0>; |
| bus-width = <4>; |
| cap-sd-highspeed; |
| sd-uhs-sdr12; |
| sd-uhs-sdr25; |
| sd-uhs-sdr50; |
| socionext,syscon-uhs-mode = <&sdctrl 0>; |
| }; |
| |
| soc_glue: syscon@5f800000 { |
| compatible = "socionext,uniphier-pxs2-soc-glue", |
| "simple-mfd", "syscon"; |
| reg = <0x5f800000 0x2000>; |
| |
| pinctrl: pinctrl { |
| compatible = "socionext,uniphier-pxs2-pinctrl"; |
| }; |
| }; |
| |
| syscon@5f900000 { |
| compatible = "socionext,uniphier-pxs2-soc-glue-debug", |
| "simple-mfd", "syscon"; |
| reg = <0x5f900000 0x2000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x5f900000 0x2000>; |
| |
| efuse@100 { |
| compatible = "socionext,uniphier-efuse"; |
| reg = <0x100 0x28>; |
| }; |
| |
| efuse@200 { |
| compatible = "socionext,uniphier-efuse"; |
| reg = <0x200 0x58>; |
| }; |
| }; |
| |
| xdmac: dma-controller@5fc10000 { |
| compatible = "socionext,uniphier-xdmac"; |
| reg = <0x5fc10000 0x5300>; |
| interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; |
| dma-channels = <16>; |
| #dma-cells = <2>; |
| }; |
| |
| aidet: interrupt-controller@5fc20000 { |
| compatible = "socionext,uniphier-pxs2-aidet"; |
| reg = <0x5fc20000 0x200>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| timer@60000200 { |
| compatible = "arm,cortex-a9-global-timer"; |
| reg = <0x60000200 0x20>; |
| interrupts = <GIC_PPI 11 |
| (GIC_CPU_MASK_RAW(0xf) | IRQ_TYPE_LEVEL_HIGH)>; |
| clocks = <&arm_timer_clk>; |
| }; |
| |
| timer@60000600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0x60000600 0x20>; |
| interrupts = <GIC_PPI 13 |
| (GIC_CPU_MASK_RAW(0xf) | IRQ_TYPE_LEVEL_HIGH)>; |
| clocks = <&arm_timer_clk>; |
| }; |
| |
| intc: interrupt-controller@60001000 { |
| compatible = "arm,cortex-a9-gic"; |
| reg = <0x60001000 0x1000>, |
| <0x60000100 0x100>; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| }; |
| |
| syscon@61840000 { |
| compatible = "socionext,uniphier-pxs2-sysctrl", |
| "simple-mfd", "syscon"; |
| reg = <0x61840000 0x10000>; |
| |
| sys_clk: clock-controller { |
| compatible = "socionext,uniphier-pxs2-clock"; |
| #clock-cells = <1>; |
| }; |
| |
| sys_rst: reset-controller { |
| compatible = "socionext,uniphier-pxs2-reset"; |
| #reset-cells = <1>; |
| }; |
| |
| pvtctl: thermal-sensor { |
| compatible = "socionext,uniphier-pxs2-thermal"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; |
| #thermal-sensor-cells = <0>; |
| socionext,tmod-calibration = <0x0f86 0x6844>; |
| }; |
| }; |
| |
| eth: ethernet@65000000 { |
| compatible = "socionext,uniphier-pxs2-ave4"; |
| status = "disabled"; |
| reg = <0x65000000 0x8500>; |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ether_rgmii>; |
| clock-names = "ether"; |
| clocks = <&sys_clk 6>; |
| reset-names = "ether"; |
| resets = <&sys_rst 6>; |
| phy-mode = "rgmii-id"; |
| local-mac-address = [00 00 00 00 00 00]; |
| socionext,syscon-phy-mode = <&soc_glue 0>; |
| |
| mdio: mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| ahci: sata@65600000 { |
| compatible = "socionext,uniphier-pxs2-ahci", |
| "generic-ahci"; |
| status = "disabled"; |
| reg = <0x65600000 0x10000>; |
| interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&sys_clk 28>; |
| resets = <&sys_rst 28>, <&ahci_rst 0>; |
| ports-implemented = <1>; |
| phys = <&ahci_phy>; |
| }; |
| |
| sata-controller@65700000 { |
| compatible = "socionext,uniphier-pxs2-ahci-glue", |
| "simple-mfd"; |
| reg = <0x65700000 0x100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x65700000 0x100>; |
| |
| ahci_rst: reset-controller@0 { |
| compatible = "socionext,uniphier-pxs2-ahci-reset"; |
| reg = <0x0 0x4>; |
| clock-names = "link"; |
| clocks = <&sys_clk 28>; |
| reset-names = "link"; |
| resets = <&sys_rst 28>; |
| #reset-cells = <1>; |
| }; |
| |
| ahci_phy: phy@10 { |
| compatible = "socionext,uniphier-pxs2-ahci-phy"; |
| reg = <0x10 0x10>; |
| clock-names = "link"; |
| clocks = <&sys_clk 28>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 28>, <&sys_rst 30>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| usb0: usb@65a00000 { |
| compatible = "socionext,uniphier-dwc3", "snps,dwc3"; |
| status = "disabled"; |
| reg = <0x65a00000 0xcd00>; |
| interrupt-names = "dwc_usb3"; |
| interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>; |
| clock-names = "ref", "bus_early", "suspend"; |
| clocks = <&sys_clk 14>, <&sys_clk 14>, <&sys_clk 14>; |
| resets = <&usb0_rst 15>; |
| phys = <&usb0_hsphy0>, <&usb0_hsphy1>, |
| <&usb0_ssphy0>, <&usb0_ssphy1>; |
| dr_mode = "host"; |
| }; |
| |
| usb-controller@65b00000 { |
| compatible = "socionext,uniphier-pxs2-dwc3-glue", |
| "simple-mfd"; |
| reg = <0x65b00000 0x400>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x65b00000 0x400>; |
| |
| usb0_rst: reset-controller@0 { |
| compatible = "socionext,uniphier-pxs2-usb3-reset"; |
| reg = <0x0 0x4>; |
| #reset-cells = <1>; |
| clock-names = "link"; |
| clocks = <&sys_clk 14>; |
| reset-names = "link"; |
| resets = <&sys_rst 14>; |
| }; |
| |
| usb0_vbus0: regulator@100 { |
| compatible = "socionext,uniphier-pxs2-usb3-regulator"; |
| reg = <0x100 0x10>; |
| clock-names = "link"; |
| clocks = <&sys_clk 14>; |
| reset-names = "link"; |
| resets = <&sys_rst 14>; |
| }; |
| |
| usb0_vbus1: regulator@110 { |
| compatible = "socionext,uniphier-pxs2-usb3-regulator"; |
| reg = <0x110 0x10>; |
| clock-names = "link"; |
| clocks = <&sys_clk 14>; |
| reset-names = "link"; |
| resets = <&sys_rst 14>; |
| }; |
| |
| usb0_hsphy0: phy@200 { |
| compatible = "socionext,uniphier-pxs2-usb3-hsphy"; |
| reg = <0x200 0x10>; |
| #phy-cells = <0>; |
| clock-names = "link", "phy"; |
| clocks = <&sys_clk 14>, <&sys_clk 16>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 14>, <&sys_rst 16>; |
| vbus-supply = <&usb0_vbus0>; |
| }; |
| |
| usb0_hsphy1: phy@210 { |
| compatible = "socionext,uniphier-pxs2-usb3-hsphy"; |
| reg = <0x210 0x10>; |
| #phy-cells = <0>; |
| clock-names = "link", "phy"; |
| clocks = <&sys_clk 14>, <&sys_clk 16>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 14>, <&sys_rst 16>; |
| vbus-supply = <&usb0_vbus1>; |
| }; |
| |
| usb0_ssphy0: phy@300 { |
| compatible = "socionext,uniphier-pxs2-usb3-ssphy"; |
| reg = <0x300 0x10>; |
| #phy-cells = <0>; |
| clock-names = "link", "phy"; |
| clocks = <&sys_clk 14>, <&sys_clk 17>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 14>, <&sys_rst 17>; |
| vbus-supply = <&usb0_vbus0>; |
| }; |
| |
| usb0_ssphy1: phy@310 { |
| compatible = "socionext,uniphier-pxs2-usb3-ssphy"; |
| reg = <0x310 0x10>; |
| #phy-cells = <0>; |
| clock-names = "link", "phy"; |
| clocks = <&sys_clk 14>, <&sys_clk 18>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 14>, <&sys_rst 18>; |
| vbus-supply = <&usb0_vbus1>; |
| }; |
| }; |
| |
| usb1: usb@65c00000 { |
| compatible = "socionext,uniphier-dwc3", "snps,dwc3"; |
| status = "disabled"; |
| reg = <0x65c00000 0xcd00>; |
| interrupt-names = "dwc_usb3"; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>; |
| clock-names = "ref", "bus_early", "suspend"; |
| clocks = <&sys_clk 15>, <&sys_clk 15>, <&sys_clk 15>; |
| resets = <&usb1_rst 15>; |
| phys = <&usb1_hsphy0>, <&usb1_hsphy1>, <&usb1_ssphy0>; |
| dr_mode = "host"; |
| }; |
| |
| usb-controller@65d00000 { |
| compatible = "socionext,uniphier-pxs2-dwc3-glue", |
| "simple-mfd"; |
| reg = <0x65d00000 0x400>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x65d00000 0x400>; |
| |
| usb1_rst: reset-controller@0 { |
| compatible = "socionext,uniphier-pxs2-usb3-reset"; |
| reg = <0x0 0x4>; |
| #reset-cells = <1>; |
| clock-names = "link"; |
| clocks = <&sys_clk 15>; |
| reset-names = "link"; |
| resets = <&sys_rst 15>; |
| }; |
| |
| usb1_vbus0: regulator@100 { |
| compatible = "socionext,uniphier-pxs2-usb3-regulator"; |
| reg = <0x100 0x10>; |
| clock-names = "link"; |
| clocks = <&sys_clk 15>; |
| reset-names = "link"; |
| resets = <&sys_rst 15>; |
| }; |
| |
| usb1_vbus1: regulator@110 { |
| compatible = "socionext,uniphier-pxs2-usb3-regulator"; |
| reg = <0x110 0x10>; |
| clock-names = "link"; |
| clocks = <&sys_clk 15>; |
| reset-names = "link"; |
| resets = <&sys_rst 15>; |
| }; |
| |
| usb1_hsphy0: phy@200 { |
| compatible = "socionext,uniphier-pxs2-usb3-hsphy"; |
| reg = <0x200 0x10>; |
| #phy-cells = <0>; |
| clock-names = "link", "phy"; |
| clocks = <&sys_clk 15>, <&sys_clk 20>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 15>, <&sys_rst 20>; |
| vbus-supply = <&usb1_vbus0>; |
| }; |
| |
| usb1_hsphy1: phy@210 { |
| compatible = "socionext,uniphier-pxs2-usb3-hsphy"; |
| reg = <0x210 0x10>; |
| #phy-cells = <0>; |
| clock-names = "link", "phy"; |
| clocks = <&sys_clk 15>, <&sys_clk 20>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 15>, <&sys_rst 20>; |
| vbus-supply = <&usb1_vbus1>; |
| }; |
| |
| usb1_ssphy0: phy@300 { |
| compatible = "socionext,uniphier-pxs2-usb3-ssphy"; |
| reg = <0x300 0x10>; |
| #phy-cells = <0>; |
| clock-names = "link", "phy"; |
| clocks = <&sys_clk 15>, <&sys_clk 21>; |
| reset-names = "link", "phy"; |
| resets = <&sys_rst 15>, <&sys_rst 21>; |
| vbus-supply = <&usb1_vbus0>; |
| }; |
| }; |
| |
| nand: nand-controller@68000000 { |
| compatible = "socionext,uniphier-denali-nand-v5b"; |
| status = "disabled"; |
| reg-names = "nand_data", "denali_reg"; |
| reg = <0x68000000 0x20>, <0x68100000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_nand2cs>; |
| clock-names = "nand", "nand_x", "ecc"; |
| clocks = <&sys_clk 2>, <&sys_clk 3>, <&sys_clk 3>; |
| reset-names = "nand", "reg"; |
| resets = <&sys_rst 2>, <&sys_rst 2>; |
| }; |
| }; |
| }; |
| |
| #include "uniphier-pinctrl.dtsi" |
