blob: fd6f07715a83a8c4e97bf19ab44afc4c1515ca2a [file] [log] [blame]
if ARCH_ZYNQMP
config SPL_FS_FAT
default y
config SPL_LIBCOMMON_SUPPORT
default y
config SPL_LIBDISK_SUPPORT
default y
config SPL_LIBGENERIC_SUPPORT
default y
config SPL_MMC
default y if MMC_SDHCI_ZYNQ
config SPL_SERIAL
default y
config SPL_SPI_FLASH_SUPPORT
default y if ZYNQ_QSPI
config SPL_SPI
default y if ZYNQ_QSPI
config SYS_BOARD
string "Board name"
default "zynqmp"
config SYS_VENDOR
string "Vendor name"
default "xilinx"
config SYS_SOC
default "zynqmp"
config SYS_CONFIG_NAME
string "Board configuration name"
default "xilinx_zynqmp"
help
This option contains information about board configuration name.
Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header
will be used for board configuration.
config SYS_MEM_RSVD_FOR_MMU
bool "Reserve memory for MMU Table"
help
If defined this option is used to setup different space for
MMU table than the one which will be allocated during
relocation.
config BOOT_INIT_FILE
string "boot.bin init register filename"
depends on SPL
default ""
help
Add register writes to boot.bin format (max 256 pairs).
Expect a table of register-value pairs, e.g. "0x12345678 0x4321"
config PMUFW_INIT_FILE
string "PMU firmware"
depends on SPL
default ""
help
Include external PMUFW (Platform Management Unit FirmWare) to
a Xilinx bootable image (boot.bin).
config ZYNQMP_SPL_PM_CFG_OBJ_FILE
string "PMU firmware configuration object to load at runtime by SPL"
depends on SPL
help
Path to a binary PMU firmware configuration object to be linked
into U-Boot SPL and loaded at runtime into the PMU firmware.
The ZynqMP Power Management Unit (PMU) needs a configuration
object for most SoC peripherals to work. To have it loaded by
U-Boot SPL set here the file name (absolute path or relative to
the top source tree) of your configuration, which must be a
binary blob. It will be linked in the SPL binary and loaded
into the PMU firmware by U-Boot SPL during board
initialization.
Leave this option empty if your PMU firmware has a hard-coded
configuration object or you are loading it by any other means.
config ZYNQMP_USB
bool "Configure ZynqMP USB"
config ZYNQMP_NO_DDR
bool "Disable DDR MMU mapping"
help
This option configures MMU with no DDR to avoid speculative
access to DDR memory where DDR is not present.
config SPL_ZYNQMP_DRAM_ECC_INIT
bool "Initialize DRAM ECC"
depends on SPL
help
This option initializes all memory to 0xdeadbeef. Must be set if your
memory is of ECC type.
config SPL_ZYNQMP_DRAM_BANK1_BASE
depends on SPL_ZYNQMP_DRAM_ECC_INIT
hex "DRAM Bank1 address"
default 0x00000000
help
Start address of DRAM ECC bank1
config SPL_ZYNQMP_DRAM_BANK1_LEN
depends on SPL_ZYNQMP_DRAM_ECC_INIT
hex "DRAM Bank1 size"
default 0x80000000
help
Size in bytes of the DRAM ECC bank1
config SPL_ZYNQMP_DRAM_BANK2_BASE
depends on SPL_ZYNQMP_DRAM_ECC_INIT
hex "DRAM Bank2 address"
default 0x800000000
help
Start address of DRAM ECC bank2
config SPL_ZYNQMP_DRAM_BANK2_LEN
depends on SPL_ZYNQMP_DRAM_ECC_INIT
hex "DRAM Bank2 size"
default 0x0
help
Size in bytes of the DRAM ECC bank2. A null size takes no action.
config SYS_MALLOC_F_LEN
default 0x600
config DEFINE_TCM_OCM_MMAP
bool "Define TCM and OCM memory in MMU Table"
default y if MP
help
This option if enabled defines the TCM and OCM memory and its
memory attributes in MMU table entry.
config ZYNQMP_PSU_INIT_ENABLED
bool "Include psu_init"
select BOARD_EARLY_INIT_F
help
Include psu_init to full u-boot.
config SPL_ZYNQMP_PSU_INIT_ENABLED
bool "Include psu_init in SPL"
default y if SPL
select BOARD_EARLY_INIT_F
help
Include psu_init by default in SPL.
config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
bool "Overwrite SPL bootmode"
depends on SPL
help
Overwrite bootmode selected via boot mode pins to tell SPL what should
be the next boot device.
config SPL_ZYNQMP_RESTORE_JTAG
bool "Restore JTAG"
depends on SPL
help
Booting SPL in secure mode causes the CSU to disable the JTAG interface
even if no eFuses were burnt. This option restores the interface if
possible.
config ZYNQ_SDHCI_MAX_FREQ
default 200000000
config SPL_ZYNQMP_ALT_BOOTMODE
hex
default 0x0 if JTAG_MODE
default 0x1 if QSPI_MODE_24BIT
default 0x2 if QSPI_MODE_32BIT
default 0x3 if SD_MODE
default 0x4 if NAND_MODE
default 0x5 if SD_MODE1
default 0x6 if EMMC_MODE
default 0x7 if USB_MODE
default 0xa if SW_USBHOST_MODE
default 0xb if SW_SATA_MODE
default 0xe if SD1_LSHFT_MODE
choice
prompt "Boot mode"
depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
default JTAG_MODE
config JTAG_MODE
bool "JTAG_MODE"
config QSPI_MODE_24BIT
bool "QSPI_MODE_24BIT"
config QSPI_MODE_32BIT
bool "QSPI_MODE_32BIT"
config SD_MODE
bool "SD_MODE"
config SD_MODE1
bool "SD_MODE1"
config NAND_MODE
bool "NAND_MODE"
config EMMC_MODE
bool "EMMC_MODE"
config USB_MODE
bool "USB"
config SW_USBHOST_MODE
bool "SW USBHOST_MODE"
config SW_SATA_MODE
bool "SW SATA_MODE"
config SD1_LSHFT_MODE
bool "SD1_LSHFT_MODE"
endchoice
source "board/xilinx/Kconfig"
source "board/xilinx/zynqmp/Kconfig"
endif