blob: 6d82bf646d267d8e82dd734ff82febe89ec31c75 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) STMicroelectronics 2021 - All Rights Reserved
* Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp13-clks.h>
#include <dt-bindings/reset/stm32mp13-resets.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
};
};
arm-pmu {
compatible = "arm,cortex-a7-pmu";
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&cpu0>;
interrupt-parent = <&intc>;
};
firmware {
optee {
method = "smc";
compatible = "linaro,optee-tz";
};
scmi: scmi {
compatible = "linaro,scmi-optee";
#address-cells = <1>;
#size-cells = <0>;
linaro,optee-channel-id = <0>;
shmem = <&scmi_shm>;
scmi_clk: protocol@14 {
reg = <0x14>;
#clock-cells = <1>;
};
scmi_reset: protocol@16 {
reg = <0x16>;
#reset-cells = <1>;
};
};
};
intc: interrupt-controller@a0021000 {
compatible = "arm,cortex-a7-gic";
#interrupt-cells = <3>;
interrupt-controller;
reg = <0xa0021000 0x1000>,
<0xa0022000 0x2000>;
};
psci {
compatible = "arm,psci-1.0";
method = "smc";
};
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
interrupt-parent = <&intc>;
always-on;
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&intc>;
ranges;
scmi_sram: sram@2ffff000 {
compatible = "mmio-sram";
reg = <0x2ffff000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x2ffff000 0x1000>;
scmi_shm: scmi-sram@0 {
compatible = "arm,scmi-shmem";
reg = <0 0x80>;
};
};
uart4: serial@40010000 {
compatible = "st,stm32h7-uart";
reg = <0x40010000 0x400>;
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART4_K>;
resets = <&rcc UART4_R>;
status = "disabled";
};
dma1: dma-controller@48000000 {
compatible = "st,stm32-dma";
reg = <0x48000000 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA1>;
resets = <&rcc DMA1_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
};
dma2: dma-controller@48001000 {
compatible = "st,stm32-dma";
reg = <0x48001000 0x400>;
interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA2>;
resets = <&rcc DMA2_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
};
dmamux1: dma-router@48002000 {
compatible = "st,stm32h7-dmamux";
reg = <0x48002000 0x40>;
clocks = <&rcc DMAMUX1>;
resets = <&rcc DMAMUX1_R>;
#dma-cells = <3>;
dma-masters = <&dma1 &dma2>;
dma-requests = <128>;
dma-channels = <16>;
};
rcc: rcc@50000000 {
compatible = "st,stm32mp13-rcc", "syscon";
reg = <0x50000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
clock-names = "hse", "hsi", "csi", "lse", "lsi";
clocks = <&scmi_clk CK_SCMI_HSE>,
<&scmi_clk CK_SCMI_HSI>,
<&scmi_clk CK_SCMI_CSI>,
<&scmi_clk CK_SCMI_LSE>,
<&scmi_clk CK_SCMI_LSI>;
};
exti: interrupt-controller@5000d000 {
compatible = "st,stm32mp13-exti", "syscon";
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000d000 0x400>;
};
syscfg: syscon@50020000 {
compatible = "st,stm32mp157-syscfg", "syscon";
reg = <0x50020000 0x400>;
clocks = <&rcc SYSCFG>;
};
mdma: dma-controller@58000000 {
compatible = "st,stm32h7-mdma";
reg = <0x58000000 0x1000>;
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc MDMA>;
#dma-cells = <5>;
dma-channels = <32>;
dma-requests = <48>;
};
fmc: memory-controller@58002000 {
compatible = "st,stm32mp1-fmc2-ebi";
reg = <0x58002000 0x1000>;
ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
<1 0 0x64000000 0x04000000>, /* EBI CS 2 */
<2 0 0x68000000 0x04000000>, /* EBI CS 3 */
<3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
<4 0 0x80000000 0x10000000>; /* NAND */
#address-cells = <2>;
#size-cells = <1>;
clocks = <&rcc FMC_K>;
resets = <&rcc FMC_R>;
status = "disabled";
nand-controller@4,0 {
compatible = "st,stm32mp1-fmc2-nfc";
reg = <4 0x00000000 0x1000>,
<4 0x08010000 0x1000>,
<4 0x08020000 0x1000>,
<4 0x01000000 0x1000>,
<4 0x09010000 0x1000>,
<4 0x09020000 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&mdma 24 0x2 0x12000a02 0x0 0x0>,
<&mdma 24 0x2 0x12000a08 0x0 0x0>,
<&mdma 25 0x2 0x12000a0a 0x0 0x0>;
dma-names = "tx", "rx", "ecc";
status = "disabled";
};
};
qspi: spi@58003000 {
compatible = "st,stm32f469-qspi";
reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
reg-names = "qspi", "qspi_mm";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&mdma 26 0x2 0x10100002 0x0 0x0>,
<&mdma 26 0x2 0x10100008 0x0 0x0>;
dma-names = "tx", "rx";
clocks = <&rcc QSPI_K>;
resets = <&rcc QSPI_R>;
status = "disabled";
};
sdmmc1: mmc@58005000 {
compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x20253180>;
reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SDMMC1_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC1_R>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <130000000>;
status = "disabled";
};
sdmmc2: mmc@58007000 {
compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x20253180>;
reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SDMMC2_K>;
clock-names = "apb_pclk";
resets = <&rcc SDMMC2_R>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <130000000>;
status = "disabled";
};
iwdg2: watchdog@5a002000 {
compatible = "st,stm32mp1-iwdg";
reg = <0x5a002000 0x400>;
clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
clock-names = "pclk", "lsi";
status = "disabled";
};
rtc: rtc@5c004000 {
compatible = "st,stm32mp1-rtc";
reg = <0x5c004000 0x400>;
interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&scmi_clk CK_SCMI_RTCAPB>,
<&scmi_clk CK_SCMI_RTC>;
clock-names = "pclk", "rtc_ck";
status = "disabled";
};
bsec: efuse@5c005000 {
compatible = "st,stm32mp13-bsec";
reg = <0x5c005000 0x400>;
#address-cells = <1>;
#size-cells = <1>;
part_number_otp: part_number_otp@4 {
reg = <0x4 0x2>;
};
ts_cal1: calib@5c {
reg = <0x5c 0x2>;
};
ts_cal2: calib@5e {
reg = <0x5e 0x2>;
};
};
/*
* Break node order to solve dependency probe issue between
* pinctrl and exti.
*/
pinctrl: pinctrl@50002000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,stm32mp135-pinctrl";
ranges = <0 0x50002000 0x8400>;
interrupt-parent = <&exti>;
st,syscfg = <&exti 0x60 0xff>;
pins-are-numbered;
gpioa: gpio@50002000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x0 0x400>;
clocks = <&rcc GPIOA>;
st,bank-name = "GPIOA";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 0 16>;
};
gpiob: gpio@50003000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x1000 0x400>;
clocks = <&rcc GPIOB>;
st,bank-name = "GPIOB";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 16 16>;
};
gpioc: gpio@50004000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x2000 0x400>;
clocks = <&rcc GPIOC>;
st,bank-name = "GPIOC";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 32 16>;
};
gpiod: gpio@50005000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x3000 0x400>;
clocks = <&rcc GPIOD>;
st,bank-name = "GPIOD";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 48 16>;
};
gpioe: gpio@50006000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x4000 0x400>;
clocks = <&rcc GPIOE>;
st,bank-name = "GPIOE";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 64 16>;
};
gpiof: gpio@50007000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000 0x400>;
clocks = <&rcc GPIOF>;
st,bank-name = "GPIOF";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 80 16>;
};
gpiog: gpio@50008000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x6000 0x400>;
clocks = <&rcc GPIOG>;
st,bank-name = "GPIOG";
ngpios = <16>;
gpio-ranges = <&pinctrl 0 96 16>;
};
gpioh: gpio@50009000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x7000 0x400>;
clocks = <&rcc GPIOH>;
st,bank-name = "GPIOH";
ngpios = <15>;
gpio-ranges = <&pinctrl 0 112 15>;
};
gpioi: gpio@5000a000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x8000 0x400>;
clocks = <&rcc GPIOI>;
st,bank-name = "GPIOI";
ngpios = <8>;
gpio-ranges = <&pinctrl 0 128 8>;
};
};
};
};