blob: b0b04842cc52c62355289e75db0ff783d92b95d5 [file] [log] [blame]
/*
* Device Tree file for Marvell Armada XP maxbcm board
*
* Copyright (C) 2013-2014 Marvell
*
* Lior Amsalem <alior@marvell.com>
* Gregory CLEMENT <gregory.clement@free-electrons.com>
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*
* Note: this Device Tree assumes that the bootloader has remapped the
* internal registers to 0xf1000000 (instead of the default
* 0xd0000000). The 0xf1000000 is the default used by the recent,
* DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
* boards were delivered with an older version of the bootloader that
* left internal registers mapped at 0xd0000000. If you are in this
* situation, you should either update your bootloader (preferred
* solution) or the below Device Tree should be adjusted.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "armada-xp-mv78460.dtsi"
/ {
model = "Marvell Armada XP MAXBCM";
compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
chosen {
stdout-path = "serial0:115200n8";
};
aliases {
spi0 = &spi0;
};
memory {
device_type = "memory";
/*
* 8 GB of plug-in RAM modules by default.The amount
* of memory available can be changed by the
* bootloader according the size of the module
* actually plugged. However, memory between
* 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
* the address range used for I/O (internal registers,
* MBus windows).
*/
reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
<0x00000001 0x00000000 0x00000001 0x00000000>;
};
cpus {
pm_pic {
ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>,
<&gpio0 17 GPIO_ACTIVE_LOW>,
<&gpio0 18 GPIO_ACTIVE_LOW>;
};
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
devbus-bootcs {
status = "okay";
/* Device Bus parameters are required */
/* Read parameters */
devbus,bus-width = <16>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
devbus,acc-next-ps = <248000>;
devbus,rd-setup-ps = <0>;
devbus,rd-hold-ps = <0>;
/* Write parameters */
devbus,sync-enable = <0>;
devbus,wr-high-ps = <60000>;
devbus,wr-low-ps = <60000>;
devbus,ale-wr-ps = <60000>;
/* NOR 16 MiB */
nor@0 {
compatible = "cfi-flash";
reg = <0 0x1000000>;
bank-width = <2>;
};
};
pcie-controller {
status = "okay";
/*
* The 3 slots are physically present as
* standard PCIe slots on the board.
*/
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
pcie@9,0 {
/* Port 2, Lane 0 */
status = "okay";
};
pcie@10,0 {
/* Port 3, Lane 0 */
status = "okay";
};
};
internal-regs {
serial@12000 {
status = "okay";
};
serial@12100 {
status = "okay";
};
serial@12200 {
status = "okay";
};
serial@12300 {
status = "okay";
};
pinctrl {
pinctrl-0 = <&pic_pins>;
pinctrl-names = "default";
pic_pins: pic-pins-0 {
marvell,pins = "mpp16", "mpp17",
"mpp18";
marvell,function = "gpio";
};
};
sata@a0000 {
nr-ports = <2>;
status = "okay";
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@0 {
reg = <0>;
};
phy1: ethernet-phy@1 {
reg = <1>;
};
phy2: ethernet-phy@2 {
reg = <2>;
};
phy3: ethernet-phy@3 {
reg = <3>;
};
};
ethernet@70000 {
status = "okay";
phy = <&phy0>;
phy-mode = "sgmii";
};
ethernet@74000 {
status = "okay";
phy = <&phy1>;
phy-mode = "sgmii";
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "sgmii";
};
ethernet@34000 {
status = "okay";
phy = <&phy3>;
phy-mode = "sgmii";
};
/* Front-side USB slot */
usb@50000 {
status = "okay";
};
/* Back-side USB slot */
usb@51000 {
status = "okay";
};
nand@d0000 {
status = "okay";
num-cs = <1>;
marvell,nand-keep-config;
marvell,nand-enable-arbiter;
nand-on-flash-bbt;
};
};
};
};
&spi0 {
status = "okay";
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "n25q128a13", "jedec,spi-nor";
reg = <0>; /* Chip select 0 */
spi-max-frequency = <108000000>;
};
};