doc/board/ti/j721e_evm.rst - u-boot - Git at Google

 .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
 .. sectionauthor:: Lokesh Vutla <lokeshvutla@ti.com>

 J721E Platforms
 ===============

 Introduction:
 -------------
 The J721e family of SoCs are part of K3 Multicore SoC architecture platform
 targeting automotive applications. They are designed as a low power, high
 performance and highly integrated device architecture, adding significant
 enhancement on processing power, graphics capability, video and imaging
 processing, virtualization and coherent memory support.

 The device is partitioned into three functional domains, each containing
 specific processing cores and peripherals:

 1. Wake-up (WKUP) domain:
         * Device Management and Security Controller (DMSC)

 2. Microcontroller (MCU) domain:
         * Dual Core ARM Cortex-R5F processor

 3. MAIN domain:
         * Dual core 64-bit ARM Cortex-A72
         * 2 x Dual cortex ARM Cortex-R5 subsystem
         * 2 x C66x Digital signal processor sub system
         * C71x Digital signal processor sub-system with MMA.

 More info can be found in TRM: https://www.ti.com/lit/pdf/spruil1

 Platform information:

 * https://www.ti.com/tool/J721EXSOMXEVM
 * https://www.ti.com/tool/SK-TDA4VM

 Boot Flow:
 ----------
 Boot flow is similar to that of AM65x SoC and extending it with remoteproc
 support. Below is the pictorial representation of boot flow:

 .. image:: img/boot_diagram_j721e.svg
   :alt: Boot flow diagram

 - Here DMSC acts as master and provides all the critical services. R5/A72
   requests DMSC to get these services done as shown in the above diagram.

 Sources:
 --------

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_boot_sources
     :end-before: .. k3_rst_include_end_boot_sources

 Build procedure:
 ----------------
 0. Setup the environment variables:

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_common_env_vars_desc
     :end-before: .. k3_rst_include_end_common_env_vars_desc

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_board_env_vars_desc
     :end-before: .. k3_rst_include_end_board_env_vars_desc

 Set the variables corresponding to this platform:

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_common_env_vars_defn
     :end-before: .. k3_rst_include_end_common_env_vars_defn
 .. prompt:: bash $

  export UBOOT_CFG_CORTEXR=j721e_evm_r5_defconfig
  export UBOOT_CFG_CORTEXA=j721e_evm_a72_defconfig
  export TFA_BOARD=generic
  # we dont use any extra TFA parameters
  unset TFA_EXTRA_ARGS
  export OPTEE_PLATFORM=k3-j721e
  # we dont use any extra OP-TEE parameters
  unset OPTEE_EXTRA_ARGS

 .. j721e_evm_rst_include_start_build_steps

 1. Trusted Firmware-A:

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_build_steps_tfa
     :end-before: .. k3_rst_include_end_build_steps_tfa


 2. OP-TEE:

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_build_steps_optee
     :end-before: .. k3_rst_include_end_build_steps_optee

 3. U-Boot:

 * 3.1 R5:

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_build_steps_spl_r5
     :end-before: .. k3_rst_include_end_build_steps_spl_r5

 * 3.2 A72:

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_build_steps_uboot
     :end-before: .. k3_rst_include_end_build_steps_uboot
 .. j721e_evm_rst_include_end_build_steps

 Target Images
 -------------

 In order to boot we need tiboot3.bin, sysfw.itb, tispl.bin and u-boot.img.
 Each SoC variant (GP, HS-FS and HS-SE) requires a different source for these
 files.

  - GP

         * tiboot3-j721e-gp-evm.bin, sysfw-j721e-gp-evm.itb from step 3.1
         * tispl.bin_unsigned, u-boot.img_unsigned from step 3.2

  - HS-FS

         * tiboot3-j721e_sr2-hs-fs-evm.bin, sysfw-j721e_sr2-hs-fs-evm.itb from step 3.1
         * tispl.bin, u-boot.img from step 3.2

  - HS-SE

         * tiboot3-j721e_sr2-hs-evm.bin, sysfw-j721e_sr2-hs-evm.itb from step 3.1
         * tispl.bin, u-boot.img from step 3.2

 Image formats:
 --------------

 - tiboot3.bin

 .. image:: img/no_multi_cert_tiboot3.bin.svg
   :alt: tiboot3.bin image format

 - tispl.bin

 .. image:: img/dm_tispl.bin.svg
   :alt: tispl.bin image format

 - sysfw.itb

 .. image:: img/sysfw.itb.svg
   :alt: sysfw.itb image format

 R5 Memory Map:
 --------------

 .. list-table::
    :widths: 16 16 16
    :header-rows: 1

    * - Region
      - Start Address
      - End Address

    * - SPL
      - 0x41c00000
      - 0x41c40000

    * - EMPTY
      - 0x41c40000
      - 0x41c81920

    * - STACK
      - 0x41c85920
      - 0x41c81920

    * - Global data
      - 0x41c859f0
      - 0x41c85920

    * - Heap
      - 0x41c859f0
      - 0x41cf59f0

    * - BSS
      - 0x41cf59f0
      - 0x41cff9f0

    * - MCU Scratchpad
      - 0x41cff9fc
      - 0x41cffbfc

    * - ROM DATA
      - 0x41cffbfc
      - 0x41cfffff

 OSPI:
 -----
 ROM supports booting from OSPI from offset 0x0.

 Flashing images to OSPI:

 Below commands can be used to download tiboot3.bin, tispl.bin, u-boot.img,
 and sysfw.itb over tftp and then flash those to OSPI at their respective
 addresses.

 .. prompt:: bash =>

   sf probe
   tftp ${loadaddr} tiboot3.bin
   sf update $loadaddr 0x0 $filesize
   tftp ${loadaddr} tispl.bin
   sf update $loadaddr 0x80000 $filesize
   tftp ${loadaddr} u-boot.img
   sf update $loadaddr 0x280000 $filesize
   tftp ${loadaddr} sysfw.itb
   sf update $loadaddr 0x6C0000 $filesize

 Flash layout for OSPI:

 .. image:: img/ospi_sysfw.svg
   :alt: OSPI flash partition layout

 Firmwares:
 ----------

 The J721e u-boot allows firmware to be loaded for the Cortex-R5 subsystem.
 The CPSW5G in J7200 and CPSW9G in J721E present in MAIN domain is configured
 and controlled by the ethernet firmware that executes in the MAIN Cortex R5.
 The default supported environment variables support loading these firmwares
 from only MMC. "dorprocboot" env variable has to be set for the U-BOOT to load
 and start the remote cores in the system.

 J721E common processor board can be attached to a Ethernet QSGMII card and the
 PHY in the card has to be reset before it can be used for data transfer.
 "do_main_cpsw0_qsgmii_phyinit" env variable has to be set for the U-BOOT to
 configure this PHY.

 Debugging U-Boot
 ----------------

 See :ref:`Common Debugging environment - OpenOCD<k3_rst_refer_openocd>`: for
 detailed setup information.

 .. warning::

   **OpenOCD support since**: v0.12.0

   If the default package version of OpenOCD in your development
   environment's distribution needs to be updated, it might be necessary to
   build OpenOCD from the source.

 .. include::  ../ti/k3.rst
     :start-after: .. k3_rst_include_start_openocd_connect_XDS110
     :end-before: .. k3_rst_include_end_openocd_connect_XDS110

 To start OpenOCD and connect to the board

 .. prompt:: bash $

   openocd -f board/ti_j721eevm.cfg
	.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
	.. sectionauthor:: Lokesh Vutla <lokeshvutla@ti.com>

	J721E Platforms
	===============

	Introduction:
	-------------
	The J721e family of SoCs are part of K3 Multicore SoC architecture platform
	targeting automotive applications. They are designed as a low power, high
	performance and highly integrated device architecture, adding significant
	enhancement on processing power, graphics capability, video and imaging
	processing, virtualization and coherent memory support.

	The device is partitioned into three functional domains, each containing
	specific processing cores and peripherals:

	1. Wake-up (WKUP) domain:
	* Device Management and Security Controller (DMSC)

	2. Microcontroller (MCU) domain:
	* Dual Core ARM Cortex-R5F processor

	3. MAIN domain:
	* Dual core 64-bit ARM Cortex-A72
	* 2 x Dual cortex ARM Cortex-R5 subsystem
	* 2 x C66x Digital signal processor sub system
	* C71x Digital signal processor sub-system with MMA.

	More info can be found in TRM: https://www.ti.com/lit/pdf/spruil1

	Platform information:

	* https://www.ti.com/tool/J721EXSOMXEVM
	* https://www.ti.com/tool/SK-TDA4VM

	Boot Flow:
	----------
	Boot flow is similar to that of AM65x SoC and extending it with remoteproc
	support. Below is the pictorial representation of boot flow:

	.. image:: img/boot_diagram_j721e.svg
	:alt: Boot flow diagram

	- Here DMSC acts as master and provides all the critical services. R5/A72
	requests DMSC to get these services done as shown in the above diagram.

	Sources:
	--------

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_boot_sources
	:end-before: .. k3_rst_include_end_boot_sources

	Build procedure:
	----------------
	0. Setup the environment variables:

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_common_env_vars_desc
	:end-before: .. k3_rst_include_end_common_env_vars_desc

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_board_env_vars_desc
	:end-before: .. k3_rst_include_end_board_env_vars_desc

	Set the variables corresponding to this platform:

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_common_env_vars_defn
	:end-before: .. k3_rst_include_end_common_env_vars_defn
	.. prompt:: bash $

	export UBOOT_CFG_CORTEXR=j721e_evm_r5_defconfig
	export UBOOT_CFG_CORTEXA=j721e_evm_a72_defconfig
	export TFA_BOARD=generic
	# we dont use any extra TFA parameters
	unset TFA_EXTRA_ARGS
	export OPTEE_PLATFORM=k3-j721e
	# we dont use any extra OP-TEE parameters
	unset OPTEE_EXTRA_ARGS

	.. j721e_evm_rst_include_start_build_steps

	1. Trusted Firmware-A:

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_build_steps_tfa
	:end-before: .. k3_rst_include_end_build_steps_tfa


	2. OP-TEE:

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_build_steps_optee
	:end-before: .. k3_rst_include_end_build_steps_optee

	3. U-Boot:

	* 3.1 R5:

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_build_steps_spl_r5
	:end-before: .. k3_rst_include_end_build_steps_spl_r5

	* 3.2 A72:

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_build_steps_uboot
	:end-before: .. k3_rst_include_end_build_steps_uboot
	.. j721e_evm_rst_include_end_build_steps

	Target Images
	-------------

	In order to boot we need tiboot3.bin, sysfw.itb, tispl.bin and u-boot.img.
	Each SoC variant (GP, HS-FS and HS-SE) requires a different source for these
	files.

	- GP

	* tiboot3-j721e-gp-evm.bin, sysfw-j721e-gp-evm.itb from step 3.1
	* tispl.bin_unsigned, u-boot.img_unsigned from step 3.2

	- HS-FS

	* tiboot3-j721e_sr2-hs-fs-evm.bin, sysfw-j721e_sr2-hs-fs-evm.itb from step 3.1
	* tispl.bin, u-boot.img from step 3.2

	- HS-SE

	* tiboot3-j721e_sr2-hs-evm.bin, sysfw-j721e_sr2-hs-evm.itb from step 3.1
	* tispl.bin, u-boot.img from step 3.2

	Image formats:
	--------------

	- tiboot3.bin

	.. image:: img/no_multi_cert_tiboot3.bin.svg
	:alt: tiboot3.bin image format

	- tispl.bin

	.. image:: img/dm_tispl.bin.svg
	:alt: tispl.bin image format

	- sysfw.itb

	.. image:: img/sysfw.itb.svg
	:alt: sysfw.itb image format

	R5 Memory Map:
	--------------

	.. list-table::
	:widths: 16 16 16
	:header-rows: 1

	* - Region
	- Start Address
	- End Address

	* - SPL
	- 0x41c00000
	- 0x41c40000

	* - EMPTY
	- 0x41c40000
	- 0x41c81920

	* - STACK
	- 0x41c85920
	- 0x41c81920

	* - Global data
	- 0x41c859f0
	- 0x41c85920

	* - Heap
	- 0x41c859f0
	- 0x41cf59f0

	* - BSS
	- 0x41cf59f0
	- 0x41cff9f0

	* - MCU Scratchpad
	- 0x41cff9fc
	- 0x41cffbfc

	* - ROM DATA
	- 0x41cffbfc
	- 0x41cfffff

	OSPI:
	-----
	ROM supports booting from OSPI from offset 0x0.

	Flashing images to OSPI:

	Below commands can be used to download tiboot3.bin, tispl.bin, u-boot.img,
	and sysfw.itb over tftp and then flash those to OSPI at their respective
	addresses.

	.. prompt:: bash =>

	sf probe
	tftp ${loadaddr} tiboot3.bin
	sf update $loadaddr 0x0 $filesize
	tftp ${loadaddr} tispl.bin
	sf update $loadaddr 0x80000 $filesize
	tftp ${loadaddr} u-boot.img
	sf update $loadaddr 0x280000 $filesize
	tftp ${loadaddr} sysfw.itb
	sf update $loadaddr 0x6C0000 $filesize

	Flash layout for OSPI:

	.. image:: img/ospi_sysfw.svg
	:alt: OSPI flash partition layout

	Firmwares:
	----------

	The J721e u-boot allows firmware to be loaded for the Cortex-R5 subsystem.
	The CPSW5G in J7200 and CPSW9G in J721E present in MAIN domain is configured
	and controlled by the ethernet firmware that executes in the MAIN Cortex R5.
	The default supported environment variables support loading these firmwares
	from only MMC. "dorprocboot" env variable has to be set for the U-BOOT to load
	and start the remote cores in the system.

	J721E common processor board can be attached to a Ethernet QSGMII card and the
	PHY in the card has to be reset before it can be used for data transfer.
	"do_main_cpsw0_qsgmii_phyinit" env variable has to be set for the U-BOOT to
	configure this PHY.

	Debugging U-Boot
	----------------

	See :ref:`Common Debugging environment - OpenOCD<k3_rst_refer_openocd>`: for
	detailed setup information.

	.. warning::

	OpenOCD support since: v0.12.0

	If the default package version of OpenOCD in your development
	environment's distribution needs to be updated, it might be necessary to
	build OpenOCD from the source.

	.. include:: ../ti/k3.rst
	:start-after: .. k3_rst_include_start_openocd_connect_XDS110
	:end-before: .. k3_rst_include_end_openocd_connect_XDS110

	To start OpenOCD and connect to the board

	.. prompt:: bash $

	openocd -f board/ti_j721eevm.cfg