blob: 2be3206f78a3e27779621d9cd8ae8efdc58e081f [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2018 NXP
*/
#include <common.h>
#include <env.h>
#include <init.h>
#include <malloc.h>
#include <errno.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm-generic/gpio.h>
#include <fsl_esdhc_imx.h>
#include <mmc.h>
#include <asm/arch/imx8mq_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/arch/clock.h>
#include <linux/delay.h>
#include <spl.h>
#include <power/pmic.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
static iomux_v3_cfg_t const wdog_pads[] = {
IMX8MQ_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
static iomux_v3_cfg_t const uart_pads[] = {
IMX8MQ_PAD_UART1_RXD__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
IMX8MQ_PAD_UART1_TXD__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
int board_early_init_f(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
return 0;
}
int board_phys_sdram_size(phys_size_t *size)
{
int ddr_size = readl(MCU_BOOTROM_BASE_ADDR);
if (ddr_size == 0x4) {
*size = 0x100000000;
} else if (ddr_size == 0x3) {
*size = 0xc0000000;
} else if (ddr_size == 0x2) {
*size = 0x80000000;
} else if (ddr_size == 0x1) {
*size = 0x40000000;
} else {
printf("Unknown DDR type!!!\n");
return -1;
}
return 0;
}
#ifdef CONFIG_FEC_MXC
#define FEC_RST_PAD IMX_GPIO_NR(1, 9)
#define FEC_PWR_PAD IMX_GPIO_NR(1, 0)
static iomux_v3_cfg_t const fec1_pads[] = {
/* Reset */
IMX8MQ_PAD_GPIO1_IO09__GPIO1_IO9 | MUX_PAD_CTRL(NO_PAD_CTRL),
/* Power */
IMX8MQ_PAD_GPIO1_IO00__GPIO1_IO0 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_iomux_fec(void)
{
imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
gpio_request(IMX_GPIO_NR(1, 0), "fec1_pwr");
gpio_direction_output(IMX_GPIO_NR(1, 0), 1);
udelay(500);
gpio_request(IMX_GPIO_NR(1, 9), "fec1_rst");
gpio_direction_output(IMX_GPIO_NR(1, 9), 0);
udelay(500);
gpio_direction_output(IMX_GPIO_NR(1, 9), 1);
}
static int setup_fec(void)
{
struct iomuxc_gpr_base_regs *gpr =
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
setup_iomux_fec();
/* Use 125M anatop REF_CLK1 for ENET1, not from external */
clrsetbits_le32(&gpr->gpr[1], BIT(13) | BIT(17), 0);
return set_clk_enet(ENET_125MHZ);
}
int board_phy_config(struct phy_device *phydev)
{
/* enable rgmii rxc skew and phy mode select to RGMII copper */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#endif
int board_init(void)
{
#ifdef CONFIG_FEC_MXC
setup_fec();
#endif
return 0;
}
int board_mmc_get_env_dev(int devno)
{
return devno;
}
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
env_set("board_rev", "iMX8MQ");
#endif
return 0;
}