| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2016 Amarula Solutions B.V. |
| * Copyright (C) 2016 Engicam S.r.l. |
| * Author: Jagan Teki <jagan@amarulasolutions.com> |
| */ |
| |
| #include <common.h> |
| #include <image.h> |
| #include <init.h> |
| #include <serial.h> |
| #include <spl.h> |
| #include <linux/delay.h> |
| |
| #include <asm/io.h> |
| #include <asm/gpio.h> |
| #include <linux/sizes.h> |
| |
| #include <asm/arch/clock.h> |
| #include <asm/arch/crm_regs.h> |
| #include <asm/arch/iomux.h> |
| #include <asm/arch/mx6-ddr.h> |
| #include <asm/arch/mx6-pins.h> |
| #include <asm/arch/sys_proto.h> |
| |
| #include <asm/mach-imx/iomux-v3.h> |
| #include <asm/mach-imx/video.h> |
| |
| #ifdef CONFIG_SPL_LOAD_FIT |
| int board_fit_config_name_match(const char *name) |
| { |
| if (is_mx6dq() && !strcmp(name, "imx6q-icore")) |
| return 0; |
| else if (is_mx6dq() && !strcmp(name, "imx6q-icore-rqs")) |
| return 0; |
| else if (is_mx6dq() && !strcmp(name, "imx6q-icore-mipi")) |
| return 0; |
| else if ((is_mx6dl() || is_mx6solo()) && !strcmp(name, "imx6dl-icore")) |
| return 0; |
| else if ((is_mx6dl() || is_mx6solo()) && !strcmp(name, "imx6dl-icore-rqs")) |
| return 0; |
| else if ((is_mx6dl() || is_mx6solo()) && !strcmp(name, "imx6dl-icore-mipi")) |
| return 0; |
| else |
| return -1; |
| } |
| #endif |
| |
| #ifdef CONFIG_ENV_IS_IN_MMC |
| void board_boot_order(u32 *spl_boot_list) |
| { |
| u32 bmode = imx6_src_get_boot_mode(); |
| u8 boot_dev = BOOT_DEVICE_MMC1; |
| |
| switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) { |
| case IMX6_BMODE_SD: |
| case IMX6_BMODE_ESD: |
| /* SD/eSD - BOOT_DEVICE_MMC1 */ |
| break; |
| case IMX6_BMODE_MMC: |
| case IMX6_BMODE_EMMC: |
| /* MMC/eMMC */ |
| boot_dev = BOOT_DEVICE_MMC2; |
| break; |
| default: |
| /* Default - BOOT_DEVICE_MMC1 */ |
| printf("Wrong board boot order\n"); |
| break; |
| } |
| |
| spl_boot_list[0] = boot_dev; |
| } |
| #endif |
| |
| #ifdef CONFIG_SPL_OS_BOOT |
| int spl_start_uboot(void) |
| { |
| /* break into full u-boot on 'c' */ |
| if (serial_tstc() && serial_getc() == 'c') |
| return 1; |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_MX6QDL |
| /* |
| * Driving strength: |
| * 0x30 == 40 Ohm |
| * 0x28 == 48 Ohm |
| */ |
| #define IMX6DQ_DRIVE_STRENGTH 0x30 |
| #define IMX6SDL_DRIVE_STRENGTH 0x28 |
| |
| /* configure MX6Q/DUAL mmdc DDR io registers */ |
| static struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = { |
| .dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm7 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_cas = IMX6DQ_DRIVE_STRENGTH, |
| .dram_ras = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_reset = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdcke0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdcke1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH, |
| }; |
| |
| /* configure MX6Q/DUAL mmdc GRP io registers */ |
| static struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = { |
| .grp_b0ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b1ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b2ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b3ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b4ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b5ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b6ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b7ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_addds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_ddrpke = 0x00000000, |
| .grp_ddrmode = 0x00020000, |
| .grp_ctlds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ddr_type = 0x000c0000, |
| }; |
| |
| /* configure MX6SOLO/DUALLITE mmdc DDR io registers */ |
| struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = { |
| .dram_sdclk_0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdclk_1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_cas = IMX6SDL_DRIVE_STRENGTH, |
| .dram_ras = IMX6SDL_DRIVE_STRENGTH, |
| .dram_reset = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdcke0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdcke1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdodt0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdodt1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs2 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs3 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs4 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs5 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs6 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs7 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm2 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm3 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm4 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm5 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm6 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm7 = IMX6SDL_DRIVE_STRENGTH, |
| }; |
| |
| /* configure MX6SOLO/DUALLITE mmdc GRP io registers */ |
| struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { |
| .grp_ddr_type = 0x000c0000, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_ddrpke = 0x00000000, |
| .grp_addds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_ctlds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_ddrmode = 0x00020000, |
| .grp_b0ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b1ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b2ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b3ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b4ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b5ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b6ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b7ds = IMX6SDL_DRIVE_STRENGTH, |
| }; |
| |
| /* mt41j256 */ |
| static struct mx6_ddr3_cfg mt41j256 = { |
| .mem_speed = 1066, |
| .density = 2, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 13, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1375, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| .SRT = 0, |
| }; |
| |
| static struct mx6_mmdc_calibration mx6dq_mmdc_calib = { |
| .p0_mpwldectrl0 = 0x000E0009, |
| .p0_mpwldectrl1 = 0x0018000E, |
| .p1_mpwldectrl0 = 0x00000007, |
| .p1_mpwldectrl1 = 0x00000000, |
| .p0_mpdgctrl0 = 0x43280334, |
| .p0_mpdgctrl1 = 0x031C0314, |
| .p1_mpdgctrl0 = 0x4318031C, |
| .p1_mpdgctrl1 = 0x030C0258, |
| .p0_mprddlctl = 0x3E343A40, |
| .p1_mprddlctl = 0x383C3844, |
| .p0_mpwrdlctl = 0x40404440, |
| .p1_mpwrdlctl = 0x4C3E4446, |
| }; |
| |
| /* DDR 64bit */ |
| static struct mx6_ddr_sysinfo mem_q = { |
| .ddr_type = DDR_TYPE_DDR3, |
| .dsize = 2, |
| .cs1_mirror = 0, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, |
| .ncs = 1, |
| .bi_on = 1, |
| .rtt_nom = 2, |
| .rtt_wr = 2, |
| .ralat = 5, |
| .walat = 0, |
| .mif3_mode = 3, |
| .rst_to_cke = 0x23, |
| .sde_to_rst = 0x10, |
| }; |
| |
| static struct mx6_mmdc_calibration mx6dl_mmdc_calib = { |
| .p0_mpwldectrl0 = 0x001F0024, |
| .p0_mpwldectrl1 = 0x00110018, |
| .p1_mpwldectrl0 = 0x001F0024, |
| .p1_mpwldectrl1 = 0x00110018, |
| .p0_mpdgctrl0 = 0x4230022C, |
| .p0_mpdgctrl1 = 0x02180220, |
| .p1_mpdgctrl0 = 0x42440248, |
| .p1_mpdgctrl1 = 0x02300238, |
| .p0_mprddlctl = 0x44444A48, |
| .p1_mprddlctl = 0x46484A42, |
| .p0_mpwrdlctl = 0x38383234, |
| .p1_mpwrdlctl = 0x3C34362E, |
| }; |
| |
| /* DDR 64bit 1GB */ |
| static struct mx6_ddr_sysinfo mem_dl = { |
| .dsize = 2, |
| .cs1_mirror = 0, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, |
| .ncs = 1, |
| .bi_on = 1, |
| .rtt_nom = 1, |
| .rtt_wr = 1, |
| .ralat = 5, |
| .walat = 0, |
| .mif3_mode = 3, |
| .rst_to_cke = 0x23, |
| .sde_to_rst = 0x10, |
| }; |
| |
| /* DDR 32bit 512MB */ |
| static struct mx6_ddr_sysinfo mem_s = { |
| .dsize = 1, |
| .cs1_mirror = 0, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, |
| .ncs = 1, |
| .bi_on = 1, |
| .rtt_nom = 1, |
| .rtt_wr = 1, |
| .ralat = 5, |
| .walat = 0, |
| .mif3_mode = 3, |
| .rst_to_cke = 0x23, |
| .sde_to_rst = 0x10, |
| }; |
| #endif /* CONFIG_MX6QDL */ |
| |
| #ifdef CONFIG_MX6UL |
| static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = { |
| .grp_addds = 0x00000030, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_b0ds = 0x00000030, |
| .grp_ctlds = 0x00000030, |
| .grp_b1ds = 0x00000030, |
| .grp_ddrpke = 0x00000000, |
| .grp_ddrmode = 0x00020000, |
| .grp_ddr_type = 0x000c0000, |
| }; |
| |
| static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = { |
| .dram_dqm0 = 0x00000030, |
| .dram_dqm1 = 0x00000030, |
| .dram_ras = 0x00000030, |
| .dram_cas = 0x00000030, |
| .dram_odt0 = 0x00000030, |
| .dram_odt1 = 0x00000030, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdclk_0 = 0x00000008, |
| .dram_sdqs0 = 0x00000038, |
| .dram_sdqs1 = 0x00000030, |
| .dram_reset = 0x00000030, |
| }; |
| |
| static struct mx6_mmdc_calibration mx6_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00070007, |
| .p0_mpdgctrl0 = 0x41490145, |
| .p0_mprddlctl = 0x40404546, |
| .p0_mpwrdlctl = 0x4040524D, |
| }; |
| |
| struct mx6_ddr_sysinfo ddr_sysinfo = { |
| .dsize = 0, |
| .cs_density = 20, |
| .ncs = 1, |
| .cs1_mirror = 0, |
| .rtt_wr = 2, |
| .rtt_nom = 1, /* RTT_Nom = RZQ/2 */ |
| .walat = 1, /* Write additional latency */ |
| .ralat = 5, /* Read additional latency */ |
| .mif3_mode = 3, /* Command prediction working mode */ |
| .bi_on = 1, /* Bank interleaving enabled */ |
| .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ |
| .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ |
| .ddr_type = DDR_TYPE_DDR3, |
| }; |
| |
| static struct mx6_ddr3_cfg mem_ddr = { |
| .mem_speed = 800, |
| .density = 4, |
| .width = 16, |
| .banks = 8, |
| #ifdef TARGET_MX6UL_ISIOT |
| .rowaddr = 15, |
| #else |
| .rowaddr = 13, |
| #endif |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1375, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| }; |
| #endif /* CONFIG_MX6UL */ |
| |
| static void ccgr_init(void) |
| { |
| struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| |
| #ifdef CONFIG_MX6QDL |
| writel(0x00003F3F, &ccm->CCGR0); |
| writel(0x0030FC00, &ccm->CCGR1); |
| writel(0x000FC000, &ccm->CCGR2); |
| writel(0x3F300000, &ccm->CCGR3); |
| writel(0xFF00F300, &ccm->CCGR4); |
| writel(0x0F0000C3, &ccm->CCGR5); |
| writel(0x000003CC, &ccm->CCGR6); |
| #elif CONFIG_MX6UL |
| writel(0x00c03f3f, &ccm->CCGR0); |
| writel(0xfcffff00, &ccm->CCGR1); |
| writel(0x0cffffcc, &ccm->CCGR2); |
| writel(0x3f3c3030, &ccm->CCGR3); |
| writel(0xff00fffc, &ccm->CCGR4); |
| writel(0x033f30ff, &ccm->CCGR5); |
| writel(0x00c00fff, &ccm->CCGR6); |
| #endif |
| } |
| |
| static void spl_dram_init(void) |
| { |
| #ifdef CONFIG_MX6QDL |
| if (is_mx6solo()) { |
| mx6sdl_dram_iocfg(32, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| mx6_dram_cfg(&mem_s, &mx6dl_mmdc_calib, &mt41j256); |
| } else if (is_mx6dl()) { |
| mx6sdl_dram_iocfg(64, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| mx6_dram_cfg(&mem_dl, &mx6dl_mmdc_calib, &mt41j256); |
| } else if (is_mx6dq()) { |
| mx6dq_dram_iocfg(64, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs); |
| mx6_dram_cfg(&mem_q, &mx6dq_mmdc_calib, &mt41j256); |
| } |
| #elif CONFIG_MX6UL |
| mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs); |
| mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr); |
| #endif |
| |
| udelay(100); |
| } |
| |
| void board_init_f(ulong dummy) |
| { |
| ccgr_init(); |
| |
| /* setup AIPS and disable watchdog */ |
| arch_cpu_init(); |
| |
| if (!(is_mx6ul())) |
| gpr_init(); |
| |
| /* setup GP timer */ |
| timer_init(); |
| |
| /* Enable device tree and early DM support*/ |
| spl_early_init(); |
| |
| /* UART clocks enabled and gd valid - init serial console */ |
| preloader_console_init(); |
| |
| /* DDR initialization */ |
| spl_dram_init(); |
| } |