blob: b37c6fe218da48a6ca5b4da478a66f72ca5a9081 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2016 Stefano Babic <sbabic@denx.de>
*/
/*
* Please note: there are two version of the board
* one with NAND and the other with eMMC.
* Both NAND and eMMC cannot be set because they share the
* same pins (SD4)
*/
#include <common.h>
#include <init.h>
#include <net.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/mx6-ddr.h>
#include <asm/global_data.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/arch/sys_proto.h>
#include <asm/sections.h>
#include <dm.h>
DECLARE_GLOBAL_DATA_PTR;
#define IMX6Q_DRIVE_STRENGTH 0x30
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
int board_mmc_get_env_dev(int devno)
{
return devno - 1;
}
#ifdef CONFIG_CMD_NAND
static void setup_gpmi_nand(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* gate ENFC_CLK_ROOT clock first,before clk source switch */
clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
/* config gpmi and bch clock to 100 MHz */
clrsetbits_le32(&mxc_ccm->cs2cdr,
MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
/* enable ENFC_CLK_ROOT clock */
setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
/* enable gpmi and bch clock gating */
setbits_le32(&mxc_ccm->CCGR4,
MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
/* enable apbh clock gating */
setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
}
#endif
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_CMD_NAND
setup_gpmi_nand();
#endif
return 0;
}
#ifdef CONFIG_CMD_BMODE
/*
* BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4
* see Table 8-11 and Table 5-9
* BOOT_CFG1[7] = 1 (boot from NAND)
* BOOT_CFG1[5] = 0 - raw NAND
* BOOT_CFG1[4] = 0 - default pad settings
* BOOT_CFG1[3:2] = 00 - devices = 1
* BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3
* BOOT_CFG2[4:3] = 00 - Boot Search Count = 2
* BOOT_CFG2[2:1] = 01 - Pages In Block = 64
* BOOT_CFG2[0] = 0 - Reset time 12ms
*/
static const struct boot_mode board_boot_modes[] = {
/* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */
{"nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00)},
{"mmc0", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
{NULL, 0},
};
#endif
int board_late_init(void)
{
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
return 0;
}
#ifdef CONFIG_SPL_BUILD
#include <spl.h>
#include <linux/libfdt.h>
static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
.dram_sdclk_0 = 0x00000030,
.dram_sdclk_1 = 0x00000030,
.dram_cas = 0x00000030,
.dram_ras = 0x00000030,
.dram_reset = 0x00000030,
.dram_sdcke0 = 0x00000030,
.dram_sdcke1 = 0x00000030,
.dram_sdba2 = 0x00000000,
.dram_sdodt0 = 0x00000030,
.dram_sdodt1 = 0x00000030,
.dram_sdqs0 = 0x00000030,
.dram_sdqs1 = 0x00000030,
.dram_sdqs2 = 0x00000030,
.dram_sdqs3 = 0x00000030,
.dram_sdqs4 = 0x00000030,
.dram_sdqs5 = 0x00000030,
.dram_sdqs6 = 0x00000030,
.dram_sdqs7 = 0x00000030,
.dram_dqm0 = 0x00000030,
.dram_dqm1 = 0x00000030,
.dram_dqm2 = 0x00000030,
.dram_dqm3 = 0x00000030,
.dram_dqm4 = 0x00000030,
.dram_dqm5 = 0x00000030,
.dram_dqm6 = 0x00000030,
.dram_dqm7 = 0x00000030,
};
static const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
.grp_ddr_type = 0x000C0000,
.grp_ddrmode_ctl = 0x00020000,
.grp_ddrpke = 0x00000000,
.grp_addds = IMX6Q_DRIVE_STRENGTH,
.grp_ctlds = IMX6Q_DRIVE_STRENGTH,
.grp_ddrmode = 0x00020000,
.grp_b0ds = IMX6Q_DRIVE_STRENGTH,
.grp_b1ds = IMX6Q_DRIVE_STRENGTH,
.grp_b2ds = IMX6Q_DRIVE_STRENGTH,
.grp_b3ds = IMX6Q_DRIVE_STRENGTH,
.grp_b4ds = IMX6Q_DRIVE_STRENGTH,
.grp_b5ds = IMX6Q_DRIVE_STRENGTH,
.grp_b6ds = IMX6Q_DRIVE_STRENGTH,
.grp_b7ds = IMX6Q_DRIVE_STRENGTH,
};
static const struct mx6_mmdc_calibration mx6_mmcd_calib = {
.p0_mpwldectrl0 = 0x00140014,
.p0_mpwldectrl1 = 0x000A0015,
.p1_mpwldectrl0 = 0x000A001E,
.p1_mpwldectrl1 = 0x000A0015,
.p0_mpdgctrl0 = 0x43080314,
.p0_mpdgctrl1 = 0x02680300,
.p1_mpdgctrl0 = 0x430C0318,
.p1_mpdgctrl1 = 0x03000254,
.p0_mprddlctl = 0x3A323234,
.p1_mprddlctl = 0x3E3C3242,
.p0_mpwrdlctl = 0x2A2E3632,
.p1_mpwrdlctl = 0x3C323E34,
};
static struct mx6_ddr3_cfg mem_ddr = {
.mem_speed = 1600,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
.SRT = 1,
};
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0x00FFF300, &ccm->CCGR4);
writel(0x0F0000C3, &ccm->CCGR5);
writel(0x000003FF, &ccm->CCGR6);
}
static void spl_dram_init(void)
{
struct mx6_ddr_sysinfo sysinfo = {
/* width of data bus:0=16,1=32,2=64 */
.dsize = 2,
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
/* single chip select */
.ncs = 1,
.cs1_mirror = 0,
.rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
.rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
.walat = 1, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.ddr_type = DDR_TYPE_DDR3,
.refsel = 1, /* Refresh cycles at 32KHz */
.refr = 7, /* 8 refresh commands per refresh cycle */
};
mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
}
void board_boot_order(u32 *spl_boot_list)
{
spl_boot_list[0] = spl_boot_device();
printf("Boot device %x\n", spl_boot_list[0]);
switch (spl_boot_list[0]) {
case BOOT_DEVICE_SPI:
spl_boot_list[1] = BOOT_DEVICE_UART;
break;
case BOOT_DEVICE_MMC1:
spl_boot_list[1] = BOOT_DEVICE_SPI;
spl_boot_list[2] = BOOT_DEVICE_UART;
break;
default:
printf("Boot device %x\n", spl_boot_list[0]);
}
}
void board_init_f(ulong dummy)
{
/* setup clock gating */
ccgr_init();
/* setup AIPS and disable watchdog */
arch_cpu_init();
/* setup AXI */
gpr_init();
/* setup GP timer */
timer_init();
/* DDR initialization */
spl_dram_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* Enable device tree and early DM support*/
spl_early_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
}
/*
* Manually probe the SPI bus devices, as this does not happen when the
* SPI Flash is probed, which then fails to find the bus.
*/
void spl_board_init(void)
{
struct udevice *udev;
int ret = uclass_get_device_by_name(UCLASS_SPI, "spi@2008000", &udev);
if (ret) {
printf("SPI bus probe failed, err = %d\n", ret);
};
}
#endif