| menu "ClearFog configuration" |
| depends on TARGET_CLEARFOG |
| |
| config TARGET_CLEARFOG_BASE |
| bool "Use ClearFog Base static configuration" |
| help |
| Use the ClearFog Base as the static configuration instead of the |
| default which uses the ClearFog Pro. |
| |
| Runtime board detection is always attempted and used if available. The |
| static configuration is used as a fallback in cases where runtime |
| detection is disabled, is not available in hardware, or otherwise fails. |
| |
| Only newer revisions of the ClearFog product line support runtime |
| detection via additional EEPROM hardware. This option enables selecting |
| the Base variant for older hardware revisions. |
| |
| config CLEARFOG_CON3_SATA |
| bool "Use CON3 slot in SATA mode" |
| help |
| Use the CON3 port with SATA protocol instead of the default PCIe. |
| The ClearFog port allows usage of either mSATA or miniPCIe |
| modules, but the desired protocol must be configured at build |
| time since it affects the SerDes topology layout. |
| |
| config CLEARFOG_CON2_SATA |
| bool "Use CON2 slot in SATA mode" |
| depends on !TARGET_CLEARFOG_BASE |
| help |
| Use the CON2 port with SATA protocol instead of the default PCIe. |
| The ClearFog port allows usage of either mSATA or miniPCIe |
| modules, but the desired protocol must be configured at build |
| time since it affects the SerDes topology layout. |
| |
| config CLEARFOG_SFP_25GB |
| bool "Enable 2.5 Gbps mode for SFP" |
| help |
| Set the SFP module connection to support 2.5 Gbps transfer speed for the |
| SGMII connection (requires a supporting SFP). By default, transfer speed |
| of 1.25 Gbps is used, suitable for a more common 1 Gbps SFP module. |
| |
| choice CLEARFOG_GTR_SERDES0 |
| prompt "Select Clearfog GTR SerDes 0 Function" |
| default CLEARFOG_GTR_SERDES0_PCIE |
| help |
| Select function for SerDes 0 which is shared between CON3 and CON18 |
| for either pci-e or sata. |
| |
| config CLEARFOG_GTR_SERDES0_PCIE |
| bool "PCI-E on CON3" |
| help |
| Configure SerDes 0 for PCI-E to enable CON3 mini-PCI-E connector. |
| |
| config CLEARFOG_GTR_SERDES0_SATA |
| bool "SATA on CON18" |
| help |
| Configure SerDes 0 for SATA to enable CON18 SATA connector. |
| |
| endchoice |
| |
| config ENV_SIZE |
| hex "Environment Size" |
| default 0x10000 |
| |
| config ENV_OFFSET |
| hex "Environment offset" |
| default 0xF0000 |
| |
| config ENV_SECT_SIZE |
| hex "Environment Sector-Size" |
| # Use SPI flash erase block size of 4 KiB |
| default 0x1000 if MVEBU_SPL_BOOT_DEVICE_SPI || MVEBU_SPL_BOOT_DEVICE_SATA |
| # Use optimistic 64 KiB erase block, will vary between actual media |
| default 0x10000 if MVEBU_SPL_BOOT_DEVICE_MMC || MVEBU_SPL_BOOT_DEVICE_UART |
| |
| endmenu |
