blob: c49b5be4762052ca7754471779e4032632e6161b [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2021 NXP
*/
#include <common.h>
#include <init.h>
#include <spl.h>
#include <asm/io.h>
#include <errno.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8ulp-pins.h>
#include <dm/uclass.h>
#include <dm/device.h>
#include <dm/uclass-internal.h>
#include <dm/device-internal.h>
#include <dm/lists.h>
#include <asm/arch/ddr.h>
#include <asm/arch/rdc.h>
#include <asm/arch/upower.h>
#include <asm/mach-imx/ele_api.h>
#include <asm/sections.h>
DECLARE_GLOBAL_DATA_PTR;
void spl_dram_init(void)
{
/* Reboot in dual boot setting no need to init ddr again */
bool ddr_enable = pcc_clock_is_enable(5, LPDDR4_PCC5_SLOT);
if (!ddr_enable) {
init_clk_ddr();
ddr_init(&dram_timing);
} else {
/* reinit pfd/pfddiv and lpavnic except pll4*/
cgc2_pll4_init(false);
}
}
u32 spl_boot_device(void)
{
return BOOT_DEVICE_BOOTROM;
}
int power_init_board(void)
{
if (IS_ENABLED(CONFIG_IMX8ULP_LD_MODE)) {
/* Set buck3 to 0.9v LD */
upower_pmic_i2c_write(0x22, 0x18);
} else if (IS_ENABLED(CONFIG_IMX8ULP_ND_MODE)) {
/* Set buck3 to 1.0v ND */
upower_pmic_i2c_write(0x22, 0x20);
} else {
/* Set buck3 to 1.1v OD */
upower_pmic_i2c_write(0x22, 0x28);
}
return 0;
}
void display_ele_fw_version(void)
{
u32 fw_version, sha1, res;
int ret;
ret = ele_get_fw_version(&fw_version, &sha1, &res);
if (ret) {
printf("ele get firmware version failed %d, 0x%x\n", ret, res);
} else {
printf("ELE firmware version %u.%u.%u-%x",
(fw_version & (0x00ff0000)) >> 16,
(fw_version & (0x0000ff00)) >> 8,
(fw_version & (0x000000ff)), sha1);
((fw_version & (0x80000000)) >> 31) == 1 ? puts("-dirty\n") : puts("\n");
}
}
void spl_board_init(void)
{
u32 res;
int ret;
ret = imx8ulp_dm_post_init();
if (ret)
return;
board_early_init_f();
preloader_console_init();
puts("Normal Boot\n");
display_ele_fw_version();
/* After AP set iomuxc0, the i2c can't work, Need M33 to set it now */
/* Load the lposc fuse to work around ROM issue. The fuse depends on S400 to read. */
if (is_soc_rev(CHIP_REV_1_0))
load_lposc_fuse();
upower_init();
power_init_board();
clock_init_late();
/* This must place after upower init, so access to MDA and MRC are valid */
/* Init XRDC MDA */
xrdc_init_mda();
/* Init XRDC MRC for VIDEO, DSP domains */
xrdc_init_mrc();
xrdc_init_pdac_msc();
/* DDR initialization */
spl_dram_init();
/* Call it after PS16 power up */
set_lpav_qos();
/* Enable A35 access to the CAAM */
ret = ele_release_caam(0x7, &res);
if (ret)
printf("ele release caam failed %d, 0x%x\n", ret, res);
/*
* RNG start only available on the A1 soc revision.
* Check some JTAG register for the SoC revision.
*/
if (!is_soc_rev(CHIP_REV_1_0)) {
ret = ele_start_rng();
if (ret)
printf("Fail to start RNG: %d\n", ret);
}
}
void board_init_f(ulong dummy)
{
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
timer_init();
arch_cpu_init();
board_init_r(NULL, 0);
}