blob: 29a1197b5ae22c42ac21f8cfd67f83c6f787a09b [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause */
/*
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
*
* Configuration settings for the STM32MP15x CPU
*/
#ifndef __CONFIG_STM32MP15_COMMMON_H
#define __CONFIG_STM32MP15_COMMMON_H
#include <linux/sizes.h>
#include <asm/arch/stm32.h>
/*
* Configuration of the external SRAM memory used by U-Boot
*/
#define CFG_SYS_SDRAM_BASE STM32_DDR_BASE
/*
* For booting Linux, use the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_SYS_BOOTMAPSZ SZ_256M
/* NAND support */
/* Ethernet need */
#define STM32MP_FIP_IMAGE_GUID \
EFI_GUID(0x19d5df83, 0x11b0, 0x457b, 0xbe, 0x2c, \
0x75, 0x59, 0xc1, 0x31, 0x42, 0xa5)
/*****************************************************************************/
#ifdef CONFIG_DISTRO_DEFAULTS
/*****************************************************************************/
#if !defined(CONFIG_SPL_BUILD)
#ifdef CONFIG_CMD_MMC
#define BOOT_TARGET_MMC0(func) func(MMC, mmc, 0)
#define BOOT_TARGET_MMC1(func) func(MMC, mmc, 1)
#define BOOT_TARGET_MMC2(func) func(MMC, mmc, 2)
#else
#define BOOT_TARGET_MMC0(func)
#define BOOT_TARGET_MMC1(func)
#define BOOT_TARGET_MMC2(func)
#endif
#ifdef CONFIG_NET
#define BOOT_TARGET_PXE(func) func(PXE, pxe, na)
#else
#define BOOT_TARGET_PXE(func)
#endif
#ifdef CONFIG_CMD_UBIFS
#define BOOT_TARGET_UBIFS(func) func(UBIFS, ubifs, 0, UBI, boot)
#else
#define BOOT_TARGET_UBIFS(func)
#endif
#ifdef CONFIG_CMD_USB
#define BOOT_TARGET_USB(func) func(USB, usb, 0)
#else
#define BOOT_TARGET_USB(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_MMC1(func) \
BOOT_TARGET_UBIFS(func) \
BOOT_TARGET_MMC0(func) \
BOOT_TARGET_MMC2(func) \
BOOT_TARGET_USB(func) \
BOOT_TARGET_PXE(func)
/*
* default bootcmd for stm32mp15:
* for serial/usb: execute the stm32prog command
* for mmc boot (eMMC, SD card), distro boot on the same mmc device
* for nand or spi-nand boot, distro boot with ubifs on UBI partition
* for nor boot, use the default distro order in ${boot_targets}
*/
#define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
"echo \"Boot over ${boot_device}${boot_instance}!\";" \
"if test ${boot_device} = serial || test ${boot_device} = usb;" \
"then stm32prog ${boot_device} ${boot_instance}; " \
"else " \
"run env_check;" \
"if test ${boot_device} = mmc;" \
"then env set boot_targets \"mmc${boot_instance}\"; fi;" \
"if test ${boot_device} = nand ||" \
" test ${boot_device} = spi-nand ;" \
"then env set boot_targets ubifs0; fi;" \
"run distro_bootcmd;" \
"fi;\0"
#define STM32MP_EXTRA \
"env_check=if env info -p -d -q; then env save; fi\0" \
"boot_net_usb_start=true\0"
#ifndef STM32MP_BOARD_EXTRA_ENV
#define STM32MP_BOARD_EXTRA_ENV
#endif
#include <config_distro_bootcmd.h>
/*
* memory layout for 32M uncompressed/compressed kernel,
* 1M fdt, 1M script, 1M pxe and 1M for overlay
* and the ramdisk at the end.
*/
#define __KERNEL_ADDR_R __stringify(0xc2000000)
#define __FDT_ADDR_R __stringify(0xc4000000)
#define __SCRIPT_ADDR_R __stringify(0xc4100000)
#define __PXEFILE_ADDR_R __stringify(0xc4200000)
#define __FDTOVERLAY_ADDR_R __stringify(0xc4300000)
#define __RAMDISK_ADDR_R __stringify(0xc4400000)
#define STM32MP_MEM_LAYOUT \
"kernel_addr_r=" __KERNEL_ADDR_R "\0" \
"fdt_addr_r=" __FDT_ADDR_R "\0" \
"scriptaddr=" __SCRIPT_ADDR_R "\0" \
"pxefile_addr_r=" __PXEFILE_ADDR_R "\0" \
"fdtoverlay_addr_r=" __FDTOVERLAY_ADDR_R "\0" \
"ramdisk_addr_r=" __RAMDISK_ADDR_R "\0"
#define CFG_EXTRA_ENV_SETTINGS \
STM32MP_MEM_LAYOUT \
STM32MP_BOOTCMD \
BOOTENV \
STM32MP_EXTRA \
STM32MP_BOARD_EXTRA_ENV
#endif /* ifndef CONFIG_SPL_BUILD */
#endif /* ifdef CONFIG_DISTRO_DEFAULTS*/
#endif /* __CONFIG_STM32MP15_COMMMON_H */