blob: b64bf93bcb748e52d8f6ffbf729bef90b9c1826c [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2016-2017
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "mx6_common.h"
#define CFG_SYS_UBOOT_BASE (CFG_SYS_FLASH_BASE + 0x80000)
/*
* Below defines are set but NOT really used since we by
* design force U-Boot run when we boot in development
* mode from SD card (SD2)
*/
#define CFG_MXC_UART_BASE UART1_BASE
/* MMC Configuration */
#define CFG_SYS_FSL_USDHC_NUM 2
#define CFG_SYS_FSL_ESDHC_ADDR 0
/* NOR 16-bit mode */
#define CFG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
/* NOR Flash MTD */
#define CFG_SYS_FLASH_BANKS_LIST { (CFG_SYS_FLASH_BASE) }
#define CFG_SYS_FLASH_BANKS_SIZES { (32 * SZ_1M) }
/* Ethernet Configuration */
#define CFG_FEC_MXC_PHYADDR 1
#define CFG_EXTRA_ENV_SETTINGS \
"console=ttymxc0,115200 quiet\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"boot_os=yes\0" \
"kernelsize=0x300000\0" \
"disable_giga=yes\0" \
"download_kernel=" \
"tftpboot ${loadaddr} ${kernel_file};\0" \
"get_boot_medium=" \
"setenv boot_medium nor;" \
"setexpr.l _src_sbmr1 *0x020d8004;" \
"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
"if test ${_b_medium} = 40; then " \
"setenv boot_medium sdcard;" \
"fi\0" \
"kernel_file=fitImage\0" \
"boot_sd=" \
"echo '#######################';" \
"echo '# Factory SDcard Boot #';" \
"echo '#######################';" \
"setenv mmcdev 1;" \
"setenv mmcfactorydev 0;" \
"setenv mmcfactorypart 1;" \
"run factory_flash_img;\0" \
"boot_nor=" \
"setenv kernelnor 0x08180000;" \
"setenv bootargs console=${console} " \
CONFIG_MTDPARTS_DEFAULT " " \
"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
"bootm ${loadaddr};reset;\0" \
"boot_recovery=" \
"echo '#######################';" \
"echo '# RECOVERY SWU Boot #';" \
"echo '#######################';" \
"setenv rootfsloadaddr 0x13000000;" \
"setenv swukernelnor 0x08980000;" \
"setenv swurootfsnor 0x09180000;" \
"setenv bootargs console=${console} " \
CONFIG_MTDPARTS_DEFAULT " " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}::off root=/dev/ram rw;" \
"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
"cp.l ${swukernelnor} ${loadaddr} ${kernelsize};" \
"bootm ${loadaddr} ${rootfsloadaddr};reset;\0" \
"boot_tftp=" \
"echo '#######################';" \
"echo '# TFTP Boot #';" \
"echo '#######################';" \
"if run download_kernel; then " \
"setenv bootargs console=${console} " \
"root=/dev/mmcblk0p2 rootwait;" \
"bootm $loadaddr};reset;" \
"fi\0" \
"bootcmd=" \
"if test -n ${recovery_status}; then " \
"run boot_recovery;" \
"else " \
"if test ! -n ${boot_medium}; then " \
"run get_boot_medium;" \
"if test ${boot_medium} = sdcard; then " \
"run boot_sd;" \
"else " \
"run boot_nor;" \
"fi;" \
"else " \
"if test ${boot_medium} = tftp; then " \
"run boot_tftp;" \
"fi;" \
"fi;" \
"fi\0" \
"bootdev=1\0" \
"bootpart=1\0" \
"netdev=eth0\0" \
"load_addr=0x11000000\0" \
"uboot_file=u-boot.img\0" \
"SPL_file=SPL\0" \
"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
"nor_img_addr=0x11000000\0" \
"nor_img_file=core-image-lwn-mccmon6.nor\0" \
"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
"nor_bank_start=" __stringify(CFG_SYS_FLASH_BASE) "\0" \
"nor_img_size=0x02000000\0" \
"factory_script_file=factory.scr\0" \
"factory_load_script=" \
"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
"${factory_script_file}; then " \
"load mmc ${mmcdev}:${mmcfactorypart} " \
"${loadaddr} ${factory_script_file};" \
"fi\0" \
"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
"source ${loadaddr}\0" \
"factory_flash_img="\
"echo 'Flash mccmon6 with factory images'; " \
"if run factory_load_script; then " \
"run factory_script;" \
"else " \
"echo No factory script: ${factory_script_file} found on " \
"device ${mmcdev};" \
"run factory_nor_img;" \
"run factory_eMMC_img;" \
"run factory_SPL_falcon_setup;" \
"fi\0" \
"factory_eMMC_img="\
"echo 'Update mccmon6 eMMC image'; " \
"if load mmc ${mmcdev}:${mmcfactorypart} " \
"${loadaddr} ${emmc_img_file}; then " \
"setexpr fw_sz ${filesize} / 0x200;" \
"setexpr fw_sz ${fw_sz} + 1;" \
"mmc dev ${mmcfactorydev};" \
"mmc write ${loadaddr} 0x0 ${fw_sz};" \
"fi\0" \
"factory_nor_img="\
"echo 'Update mccmon6 NOR image'; " \
"if load mmc ${mmcdev}:${mmcfactorypart} " \
"${nor_img_addr} ${nor_img_file}; then " \
"run nor_update;" \
"fi\0" \
"nor_update=" \
"protect off ${nor_bank_start} +${nor_img_size};" \
"erase ${nor_bank_start} +${nor_img_size};" \
"setexpr nor_img_size ${nor_img_size} / 4; " \
"cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
"factory_SPL_falcon_setup="\
"echo 'Write Falcon boot data'; " \
"setenv kernelnor 0x08180000;" \
"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
"spl export fdt ${loadaddr};" \
"setenv nor_img_addr ${fdtargsaddr};" \
"setenv nor_img_size 0x20000;" \
"setenv nor_bank_start " \
__stringify(CONFIG_CMD_SPL_NOR_OFS)";" \
"run nor_update\0" \
"tftp_nor_uboot="\
"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
"setenv nor_img_file u-boot.img; " \
"setenv nor_img_size 0x80000; " \
"setenv nor_bank_start 0x08080000; " \
"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
"run nor_update;" \
"fi\0" \
"tftp_nor_fitImg="\
"echo 'Update mccmon6 NOR fitImage via TFTP'; " \
"setenv nor_img_file fitImage; " \
"setenv nor_img_size 0x500000; " \
"setenv nor_bank_start 0x08180000; " \
"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
"run nor_update;" \
"fi\0" \
"tftp_nor_img="\
"echo 'Update mccmon6 NOR image via TFTP'; " \
"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
"run nor_update;" \
"fi\0" \
"tftp_nor_SPL="\
"if tftp ${load_addr} SPL_padded; then " \
"erase 0x08000000 +0x20000;" \
"cp.b ${load_addr} 0x08000000 0x20000;" \
"fi;\0" \
"tftp_sd_SPL="\
"if mmc dev 1; then " \
"if tftp ${load_addr} ${SPL_file}; then " \
"setexpr fw_sz ${filesize} / 0x200; " \
"setexpr fw_sz ${fw_sz} + 1; " \
"mmc write ${load_addr} 0x2 ${fw_sz};" \
"fi;" \
"fi;\0" \
"tftp_sd_uboot="\
"if mmc dev 1; then " \
"if run load_uboot; then " \
"setexpr fw_sz ${filesize} / 0x200; " \
"setexpr fw_sz ${fw_sz} + 1; " \
"mmc write ${load_addr} 0x8A ${fw_sz};" \
"fi;" \
"fi;\0"
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CFG_SYS_SDRAM_BASE PHYS_SDRAM
#define CFG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CFG_SYS_INIT_RAM_SIZE IRAM_SIZE
/* Environment organization */
/* Envs are stored in NOR flash */
#endif /* __CONFIG_H * */