blob: 29951f7f122090953b0a3a0f6f383b568ce2e362 [file] [log] [blame]
/*
* (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2006
* Eric Schumann, Phytec Messatechnik GmbH
*
* (C) Copyright 2009
* Jon Smirl <jonsmirl@gmail.com>
*
* (C) Copyright 2009
* Eric Millbrandt, DEKA Research and Development Corporation
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_BOARDINFO "galaxy5200"
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */
#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 -> */
/* define gps port conf. */
/* register later on to */
/* enable UART function! */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_PING
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_USB
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_FAT
#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
#if (TEXT_BASE == 0xFE000000) /* Boot low */
#define CONFIG_SYS_LOWBOOT 1
#endif
/* RAMBOOT will be defined automatically in memory section */
#define MTDIDS_DEFAULT "nor0=physmap-flash.0"
#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \
"1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)"
/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */
/* even with bootdelay=0 */
#define CONFIG_BOOT_RETRY_TIME 120 /* Reset if no command is entered */
#define CONFIG_RESET_TO_RETRY
#define CONFIG_PREBOOT "echo;" \
"echo Welcome to U-Boot;"\
"echo"
#define CONFIG_BOOTCOMMAND "go ff300004 0; go ff300004 2 2;" \
"bootm ff040000 ff900000 fffc0000"
#define CONFIG_BOOTARGS "console=ttyPSC0,115200"
#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0"
/*
* IPB Bus clocking configuration.
*/
#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#define CONFIG_SYS_XLB_PIPELINING 1
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_INIT_MPC5XXX /* Reset devices on i2c bus */
/*
* EEPROM CAT24WC32 configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */
#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */
#define CONFIG_SYS_EEPROM_SIZE 4096
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
/*
* RTC configuration
*/
#define RTC
#define CONFIG_RTC_DS3231 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/*
* Flash configuration
*/
#define CONFIG_SYS_FLASH_BASE 0xfe000000
/*
* The flash size is autoconfigured, but arch/powerpc/cpu/mpc5xxx/cpu_init.c needs this
* variable defined
*/
#define CONFIG_SYS_FLASH_SIZE 0x02000000
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max num of sects on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
/* (= chip selects) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
/*
* Use hardware protection. This seems required, as the BDI uses hardware
* protection. Without this, U-Boot can't work with this sectors as its
* protection is software only by default.
*/
#define CONFIG_SYS_FLASH_PROTECTION 1
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_EEPROM 1
#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */
/* beginning of the EEPROM */
#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE
#define CONFIG_ENV_OVERWRITE 1
/*
* SDRAM configuration
*/
#define SDRAM_DDR 1
#define SDRAM_MODE 0x018D0000
#define SDRAM_EMODE 0x40090000
#define SDRAM_CONTROL 0x71500F00
#define SDRAM_CONFIG1 0x73711930
#define SDRAM_CONFIG2 0x47770000
/*
* Memory map
*/
#define CONFIG_SYS_MBAR 0xF0000000 /* MBAR has to be switched by other */
/* bootloader or debugger config */
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use SRAM until RAM will be available */
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
/* End of used area in SPRAM */
#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE
/* Size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_SIZE 128
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \
CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/* Chip Select configuration for NAND flash */
#define CONFIG_SYS_CS1_START 0x20000000
#define CONFIG_SYS_CS1_SIZE 0x90000
#define CONFIG_SYS_CS1_CFG 0x00025b00
/* Chip Select configuration for Epson S1D13513 */
#define CONFIG_SYS_CS3_START 0x10000000
#define CONFIG_SYS_CS3_SIZE 0x400000
#define CONFIG_SYS_CS3_CFG 0xffff3d10
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_MPC5xxx_FEC_MII100
#define CONFIG_PHY_ADDR 0x01
#define CONFIG_NO_AUTOLOAD 1
/*
* GPIO configuration
*
* GPS port configuration
*
* [29:31] = 01x
* AC97 on PSC1
* PSC1_0 -> AC97 SDATA out
* PSC1_1 -> AC97 SDTA in
* PSC1_2 -> AC97 SYNC out
* PSC1_3 -> AC97 bitclock out
* PSC1_4 -> AC97 reset out
*
* [28] = Reserved
*
* [25:27] = 110
* SPI on PSC2
* PSC2_0 -> MOSI
* PSC2_1 -> MISO
* PSC2_2 -> n/a
* PSC2_3 -> CLK
* PSC2_4 -> SS
*
* [24] = Reserved
*
* [20:23] = 0001
* USB on PSC3
* PSC3_0 -> USB_OE OE out
* PSC3_1 -> USB_TXN Tx- out
* PSC3_2 -> USB_TXP Tx+ out
* PSC3_3 -> USB_TXD
* PSC3_4 -> USB_RXP Rx+ in
* PSC3_5 -> USB_RXN Rx- in
* PSC3_6 -> USB_PWR PortPower out
* PSC3_7 -> USB_SPEED speed out
* PSC3_8 -> USB_SUSPEND suspend
* PSC3_9 -> USB_OVRCURNT overcurrent in
*
* [18:19] = 10
* Two UARTs
*
* [17] = 0
* USB differential mode
*
* [16] = 1
* PCI disabled
*
* [12:15] = 0101
* Ethernet 100Mbit with MD
* ETH_0 -> ETH Txen
* ETH_1 -> ETH TxD0
* ETH_2 -> ETH TxD1
* ETH_3 -> ETH TxD2
* ETH_4 -> ETH TxD3
* ETH_5 -> ETH Txerr
* ETH_6 -> ETH MDC
* ETH_7 -> ETH MDIO
* ETH_8 -> ETH RxDv
* ETH_9 -> ETH RxCLK
* ETH_10 -> ETH Collision
* ETH_11 -> ETH TxD
* ETH_12 -> ETH RxD0
* ETH_13 -> ETH RxD1
* ETH_14 -> ETH RxD2
* ETH_15 -> ETH RxD3
* ETH_16 -> ETH Rxerr
* ETH_17 -> ETH CRS
*
* [9:11] = 111
* SPI on PSC6
* PSC6_0 -> MISO
* PSC6_1 -> SS#
* PSC6_2 -> MOSI
* PSC6_3 -> CLK
*
* [8] = 0
* IrDA/USB 48MHz clock generated internally
*
* [6:7] = 01
* ATA chip selects on csb_4/5
* CSB_4 -> ATA_CS0 out
* CSB_5 -> ATA_CS1 out
*
* [5] = 1
* PSC3_4 is used as CS6
*
* [4] = 1
* PSC3_5 is used as CS7
*
* [2:3] = 00
* No Alternatives
*
* [1] = 0
* gpio_wkup_7 is GPIO
*
* [0] = 0
* gpio_wkup_6 is GPIO
*
*/
#define CONFIG_SYS_GPS_PORT_CONFIG 0x0d75a162
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_DISPLAY_BOARDINFO 1
#define CONFIG_SYS_HUSH_PARSER 1
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_CRC32_VERIFY 1
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_DNS | \
CONFIG_BOOTP_DNS2 | \
CONFIG_BOOTP_SEND_HOSTNAME )
#define CONFIG_VERSION_VARIABLE 1
/*
* Various low-level settings
*/
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
#define CONFIG_SYS_HID0_FINAL HID0_ICE
/* no burst access on the LPB */
#define CONFIG_SYS_CS_BURST 0x00000000
/* one deadcycle for the 33MHz statemachine */
#define CONFIG_SYS_CS_DEADCYCLE 0x33333331
#define CONFIG_SYS_BOOTCS_CFG 0x0002d900
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_RESET_ADDRESS 0xff000000
/*
* USB settings
*/
#define CONFIG_USB_CLOCK 0x0001bbbb
/* USB is on PSC3 */
#define CONFIG_PSC3_USB
#define CONFIG_USB_CONFIG 0x00000100
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
/*
* IDE/ATA stuff Supports IDE harddisk
*/
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
#define CONFIG_IDE_PREINIT
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
#define CONFIG_SYS_ATA_STRIDE 4
#define CONFIG_ATAPI 1
/* we enable IDE and FAT support, so we also need partition support */
#define CONFIG_DOS_PARTITION 1
/*
* Open Firmware flat tree
*/
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define OF_CPU "PowerPC,5200@0"
#define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN
#define OF_SOC "soc5200@f0000000"
#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2600"
#endif /* __CONFIG_H */