blob: 96fd990c71c44c622f1177311b014e9e61d076fe [file] [log] [blame]
/*
* Functions related to OMAP3 SDRC.
*
* This file has been created after exctracting and consolidating
* the SDRC related content from mem.c and board.c, also created
* generic init function (mem_init).
*
* Copyright (C) 2004-2010
* Texas Instruments Incorporated - http://www.ti.com/
*
* Author :
* Vaibhav Hiremath <hvaibhav@ti.com>
*
* Original implementation by (mem.c, board.c) :
* Sunil Kumar <sunilsaini05@gmail.com>
* Shashi Ranjan <shashiranjanmca05@gmail.com>
* Manikandan Pillai <mani.pillai@ti.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/mem.h>
#include <asm/arch/sys_proto.h>
extern omap3_sysinfo sysinfo;
static struct sdrc *sdrc_base = (struct sdrc *)OMAP34XX_SDRC_BASE;
/*
* is_mem_sdr -
* - Return 1 if mem type in use is SDR
*/
u32 is_mem_sdr(void)
{
if (readl(&sdrc_base->cs[CS0].mr) == SDRC_MR_0_SDR)
return 1;
return 0;
}
/*
* make_cs1_contiguous -
* - For es2 and above remap cs1 behind cs0 to allow command line
* mem=xyz use all memory with out discontinuous support compiled in.
* Could do it at the ATAG, but there really is two banks...
* - Called as part of 2nd phase DDR init.
*/
void make_cs1_contiguous(void)
{
u32 size, a_add_low, a_add_high;
size = get_sdr_cs_size(CS0);
size >>= 25; /* divide by 32 MiB to find size to offset CS1 */
a_add_high = (size & 3) << 8; /* set up low field */
a_add_low = (size & 0x3C) >> 2; /* set up high field */
writel((a_add_high | a_add_low), &sdrc_base->cs_cfg);
}
/*
* get_sdr_cs_size -
* - Get size of chip select 0/1
*/
u32 get_sdr_cs_size(u32 cs)
{
u32 size;
/* get ram size field */
size = readl(&sdrc_base->cs[cs].mcfg) >> 8;
size &= 0x3FF; /* remove unwanted bits */
size <<= 21; /* multiply by 2 MiB to find size in MB */
return size;
}
/*
* get_sdr_cs_offset -
* - Get offset of cs from cs0 start
*/
u32 get_sdr_cs_offset(u32 cs)
{
u32 offset;
if (!cs)
return 0;
offset = readl(&sdrc_base->cs_cfg);
offset = (offset & 15) << 27 | (offset & 0x30) >> 17;
return offset;
}
/*
* do_sdrc_init -
* - Initialize the SDRAM for use.
* - Sets up SDRC timings for CS0
* - code called once in C-Stack only context for CS0 and a possible 2nd
* time depending on memory configuration from stack+global context
*/
void do_sdrc_init(u32 cs, u32 early)
{
struct sdrc_actim *sdrc_actim_base;
if (cs)
sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
else
sdrc_actim_base = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
if (early) {
/* reset sdrc controller */
writel(SOFTRESET, &sdrc_base->sysconfig);
wait_on_value(RESETDONE, RESETDONE, &sdrc_base->status,
12000000);
writel(0, &sdrc_base->sysconfig);
/* setup sdrc to ball mux */
writel(SDRC_SHARING, &sdrc_base->sharing);
/* Disable Power Down of CKE cuz of 1 CKE on combo part */
writel(WAKEUPPROC | SRFRONRESET | PAGEPOLICY_HIGH,
&sdrc_base->power);
writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
sdelay(0x20000);
}
writel(RASWIDTH_13BITS | CASWIDTH_10BITS | ADDRMUXLEGACY |
RAMSIZE_128 | BANKALLOCATION | B32NOT16 | B32NOT16 |
DEEPPD | DDR_SDRAM, &sdrc_base->cs[cs].mcfg);
writel(ARCV | ARE_ARCV_1, &sdrc_base->cs[cs].rfr_ctrl);
writel(V_ACTIMA_165, &sdrc_actim_base->ctrla);
writel(V_ACTIMB_165, &sdrc_actim_base->ctrlb);
writel(CMD_NOP, &sdrc_base->cs[cs].manual);
writel(CMD_PRECHARGE, &sdrc_base->cs[cs].manual);
writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
writel(CMD_AUTOREFRESH, &sdrc_base->cs[cs].manual);
/*
* CAS latency 3, Write Burst = Read Burst, Serial Mode,
* Burst length = 4
*/
writel(CASL3 | BURSTLENGTH4, &sdrc_base->cs[cs].mr);
if (!mem_ok(cs))
writel(0, &sdrc_base->cs[cs].mcfg);
}
/*
* dram_init -
* - Sets uboots idea of sdram size
*/
int dram_init(void)
{
DECLARE_GLOBAL_DATA_PTR;
unsigned int size0 = 0, size1 = 0;
size0 = get_sdr_cs_size(CS0);
/*
* If a second bank of DDR is attached to CS1 this is
* where it can be started. Early init code will init
* memory on CS0.
*/
if ((sysinfo.mtype == DDR_COMBO) || (sysinfo.mtype == DDR_STACKED)) {
do_sdrc_init(CS1, NOT_EARLY);
make_cs1_contiguous();
size1 = get_sdr_cs_size(CS1);
}
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
gd->bd->bi_dram[0].size = size0;
gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + get_sdr_cs_offset(CS1);
gd->bd->bi_dram[1].size = size1;
return 0;
}
/*
* mem_init -
* - Init the sdrc chip,
* - Selects CS0 and CS1,
*/
void mem_init(void)
{
/* only init up first bank here */
do_sdrc_init(CS0, EARLY_INIT);
}