Google Git
Sign in
qemu / skiboot / refs/tags/v6.0.24 / . / hw / p8-i2c.c
blob: 1bcd7cc8b42079ba9146fa27017cf3661289d344 [file] [log] [blame]
/* Copyright 2013-2017 IBM Corp.
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or
* implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
#undef DEBUG
#include <opal.h>
#include <skiboot.h>
#include <mem_region-malloc.h>
#include <lock.h>
#include <chip.h>
#include <i2c.h>
#include <xscom.h>
#include <timebase.h>
#include <timer.h>
#include <opal-msg.h>
#include <errorlog.h>
#include <centaur.h>
DEFINE_LOG_ENTRY(OPAL_RC_I2C_INIT, OPAL_PLATFORM_ERR_EVT, OPAL_I2C,
OPAL_IO_SUBSYSTEM, OPAL_PREDICTIVE_ERR_DEGRADED_PERF,
OPAL_NA);
DEFINE_LOG_ENTRY(OPAL_RC_I2C_START_REQ, OPAL_INPUT_OUTPUT_ERR_EVT, OPAL_I2C,
OPAL_IO_SUBSYSTEM, OPAL_INFO, OPAL_NA);
DEFINE_LOG_ENTRY(OPAL_RC_I2C_TIMEOUT, OPAL_INPUT_OUTPUT_ERR_EVT, OPAL_I2C,
OPAL_IO_SUBSYSTEM, OPAL_INFO, OPAL_NA);
DEFINE_LOG_ENTRY(OPAL_RC_I2C_TRANSFER, OPAL_INPUT_OUTPUT_ERR_EVT, OPAL_I2C,
OPAL_IO_SUBSYSTEM, OPAL_INFO, OPAL_NA);
DEFINE_LOG_ENTRY(OPAL_RC_I2C_RESET, OPAL_INPUT_OUTPUT_ERR_EVT, OPAL_I2C,
OPAL_IO_SUBSYSTEM, OPAL_INFO, OPAL_NA);
#ifdef DEBUG
#define DBG(fmt...) prlog(PR_ERR, "I2C: " fmt)
#define I2C_TIMEOUT_IRQ_MS 100 /* 100ms/byte timeout */
#define I2C_TIMEOUT_POLL_MS 4000 /* 4s/byte timeout */
#else
#define DBG(fmt...) prlog(PR_TRACE, "I2C: " fmt)
#define I2C_TIMEOUT_IRQ_MS 1 /* 1ms/byte timeout */
#define I2C_TIMEOUT_POLL_MS 4000 /* 4s/byte timeout */
#endif
/* How long to keep the sensor cache disabled after an access
* in milliseconds
*/
#define SENSOR_CACHE_EN_DELAY 10
#define USEC_PER_SEC 1000000
#define USEC_PER_MSEC 1000
#define I2C_RESET_DELAY_MS 5 /* 5 msecs */
#define I2C_FIFO_HI_LVL 4
#define I2C_FIFO_LO_LVL 4
/*
* I2C registers set.
* Below is the offset of registers from base which is stored in the
* 'struct p8_i2c_master'
*/
/* I2C FIFO register */
#define I2C_FIFO_REG 0x4
#define I2C_FIFO PPC_BITMASK(0, 7)
/* I2C command register */
#define I2C_CMD_REG 0x5
#define I2C_CMD_WITH_START PPC_BIT(0)
#define I2C_CMD_WITH_ADDR PPC_BIT(1)
#define I2C_CMD_READ_CONT PPC_BIT(2)
#define I2C_CMD_WITH_STOP PPC_BIT(3)
#define I2C_CMD_INTR_STEERING PPC_BITMASK(6,7) /* P9 */
#define I2C_CMD_INTR_STEER_HOST 1
#define I2C_CMD_INTR_STEER_OCC 2
#define I2C_CMD_DEV_ADDR PPC_BITMASK(8, 14)
#define I2C_CMD_READ_NOT_WRITE PPC_BIT(15)
#define I2C_CMD_LEN_BYTES PPC_BITMASK(16, 31)
#define I2C_MAX_TFR_LEN 0xfff0ull
/* I2C mode register */
#define I2C_MODE_REG 0x6
#define I2C_MODE_BIT_RATE_DIV PPC_BITMASK(0, 15)
#define I2C_MODE_PORT_NUM PPC_BITMASK(16, 21)
#define I2C_MODE_ENHANCED PPC_BIT(28)
#define I2C_MODE_DIAGNOSTIC PPC_BIT(29)
#define I2C_MODE_PACING_ALLOW PPC_BIT(30)
#define I2C_MODE_WRAP PPC_BIT(31)
/* I2C watermark register */
#define I2C_WATERMARK_REG 0x7
#define I2C_WATERMARK_HIGH PPC_BITMASK(16, 19)
#define I2C_WATERMARK_LOW PPC_BITMASK(24, 27)
/* I2C interrupt mask, condition and interrupt registers */
#define I2C_INTR_MASK_REG 0x8
#define I2C_INTR_COND_REG 0x9
#define I2C_INTR_REG 0xa
#define I2C_INTR_ALL PPC_BITMASK(16, 31)
#define I2C_INTR_INVALID_CMD PPC_BIT(16)
#define I2C_INTR_LBUS_PARITY_ERR PPC_BIT(17)
#define I2C_INTR_BKEND_OVERRUN_ERR PPC_BIT(18)
#define I2C_INTR_BKEND_ACCESS_ERR PPC_BIT(19)
#define I2C_INTR_ARBT_LOST_ERR PPC_BIT(20)
#define I2C_INTR_NACK_RCVD_ERR PPC_BIT(21)
#define I2C_INTR_DATA_REQ PPC_BIT(22)
#define I2C_INTR_CMD_COMP PPC_BIT(23)
#define I2C_INTR_STOP_ERR PPC_BIT(24)
#define I2C_INTR_I2C_BUSY PPC_BIT(25)
#define I2C_INTR_NOT_I2C_BUSY PPC_BIT(26)
#define I2C_INTR_SCL_EQ_1 PPC_BIT(28)
#define I2C_INTR_SCL_EQ_0 PPC_BIT(29)
#define I2C_INTR_SDA_EQ_1 PPC_BIT(30)
#define I2C_INTR_SDA_EQ_0 PPC_BIT(31)
/* I2C status register */
#define I2C_RESET_I2C_REG 0xb
#define I2C_RESET_ERRORS 0xc
#define I2C_STAT_REG 0xb
#define I2C_STAT_INVALID_CMD PPC_BIT(0)
#define I2C_STAT_LBUS_PARITY_ERR PPC_BIT(1)
#define I2C_STAT_BKEND_OVERRUN_ERR PPC_BIT(2)
#define I2C_STAT_BKEND_ACCESS_ERR PPC_BIT(3)
#define I2C_STAT_ARBT_LOST_ERR PPC_BIT(4)
#define I2C_STAT_NACK_RCVD_ERR PPC_BIT(5)
#define I2C_STAT_DATA_REQ PPC_BIT(6)
#define I2C_STAT_CMD_COMP PPC_BIT(7)
#define I2C_STAT_STOP_ERR PPC_BIT(8)
#define I2C_STAT_UPPER_THRS PPC_BITMASK(9, 15)
#define I2C_STAT_ANY_I2C_INTR PPC_BIT(16)
#define I2C_STAT_PORT_HISTORY_BUSY PPC_BIT(19)
#define I2C_STAT_SCL_INPUT_LEVEL PPC_BIT(20)
#define I2C_STAT_SDA_INPUT_LEVEL PPC_BIT(21)
#define I2C_STAT_PORT_BUSY PPC_BIT(22)
#define I2C_STAT_INTERFACE_BUSY PPC_BIT(23)
#define I2C_STAT_FIFO_ENTRY_COUNT PPC_BITMASK(24, 31)
#define I2C_STAT_ANY_ERR (I2C_STAT_INVALID_CMD | I2C_STAT_LBUS_PARITY_ERR | \
I2C_STAT_BKEND_OVERRUN_ERR | \
I2C_STAT_BKEND_ACCESS_ERR | I2C_STAT_ARBT_LOST_ERR | \
I2C_STAT_NACK_RCVD_ERR | I2C_STAT_STOP_ERR)
/* Pseudo-status used for timeouts */
#define I2C_STAT_PSEUDO_TIMEOUT PPC_BIT(63)
/* I2C extended status register */
#define I2C_EXTD_STAT_REG 0xc
#define I2C_EXTD_STAT_FIFO_SIZE PPC_BITMASK(0, 7)
#define I2C_EXTD_STAT_MSM_CURSTATE PPC_BITMASK(11, 15)
#define I2C_EXTD_STAT_SCL_IN_SYNC PPC_BIT(16)
#define I2C_EXTD_STAT_SDA_IN_SYNC PPC_BIT(17)
#define I2C_EXTD_STAT_S_SCL PPC_BIT(18)
#define I2C_EXTD_STAT_S_SDA PPC_BIT(19)
#define I2C_EXTD_STAT_M_SCL PPC_BIT(20)
#define I2C_EXTD_STAT_M_SDA PPC_BIT(21)
#define I2C_EXTD_STAT_HIGH_WATER PPC_BIT(22)
#define I2C_EXTD_STAT_LOW_WATER PPC_BIT(23)
#define I2C_EXTD_STAT_I2C_BUSY PPC_BIT(24)
#define I2C_EXTD_STAT_SELF_BUSY PPC_BIT(25)
#define I2C_EXTD_STAT_I2C_VERSION PPC_BITMASK(27, 31)
/* I2C residual front end/back end length */
#define I2C_RESIDUAL_LEN_REG 0xd
#define I2C_RESIDUAL_FRONT_END PPC_BITMASK(0, 15)
#define I2C_RESIDUAL_BACK_END PPC_BITMASK(16, 31)
/* Port busy register */
#define I2C_PORT_BUSY_REG 0xe
#define I2C_SET_S_SCL_REG 0xd
#define I2C_RESET_S_SCL_REG 0xf
#define I2C_SET_S_SDA_REG 0x10
#define I2C_RESET_S_SDA_REG 0x11
enum p8_i2c_master_type {
I2C_POWER8,
I2C_CENTAUR,
MAX_I2C_TYPE,
};
struct p8_i2c_master {
struct lock lock; /* Lock to guard the members */
enum p8_i2c_master_type type; /* P8 vs. Centaur */
uint64_t start_time; /* Request start time */
uint64_t last_update;
uint64_t poll_interval; /* Polling interval */
uint64_t xscom_base; /* xscom base of i2cm */
uint32_t fifo_size; /* Maximum size of FIFO */
uint32_t chip_id; /* Chip the i2cm sits on */
uint32_t engine_id; /* Engine# on chip */
uint8_t obuf[4]; /* Offset buffer */
uint32_t bytes_sent;
bool irq_ok; /* Interrupt working ? */
bool occ_cache_dis; /* I have disabled the cache */
bool occ_lock_acquired; /* Acquired lock from OCC */
enum request_state {
state_idle,
state_occache_dis,
state_offset,
state_data,
state_error,
state_recovery,
} state;
struct list_head req_list; /* Request queue head */
struct timer poller;
struct timer timeout;
struct timer recovery;
struct timer sensor_cache;
uint8_t recovery_pass;
struct list_node link;
struct list_head ports;
};
struct p8_i2c_master_port {
struct i2c_bus bus; /* Abstract bus struct for the client */
struct p8_i2c_master *master;
uint32_t port_num;
uint32_t bit_rate_div; /* Divisor to set bus speed*/
uint64_t byte_timeout; /* Timeout per byte */
struct list_node link;
};
struct p8_i2c_request {
struct i2c_request req;
uint32_t port_num;
uint64_t timeout;
};
static int occ_i2c_unlock(struct p8_i2c_master *master);
static int64_t i2cm_read_reg(struct p8_i2c_master *m, int reg, uint64_t *val)
{
return xscom_read(m->chip_id, m->xscom_base + reg, val);
}
static int64_t i2cm_write_reg(struct p8_i2c_master *m, int reg, uint64_t val)
{
return xscom_write(m->chip_id, m->xscom_base + reg, val);
}
static void p8_i2c_print_debug_info(struct p8_i2c_master_port *port,
struct i2c_request *req, uint64_t end_time)
{
struct p8_i2c_master *master = port->master;
uint64_t cmd, mode, stat, estat, intm, intc;
int rc;
/* Print master and request structure bits */
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER),
"I2C: Chip %08x Eng. %d Port %d--\n"
" xscom_base=0x%016llx\tstate=%d\tbytes_sent=%d\n",
master->chip_id, master->engine_id, port->port_num,
master->xscom_base, master->state, master->bytes_sent);
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: Request info--\n"
" addr=0x%04x\toffset_bytes=%d\toffset=%d\tlen=%d\n",
req->dev_addr, req->offset_bytes, req->offset,
req->rw_len);
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: "
" start_time=%016llx end_time=%016llx (duration=%016llx)\n",
master->start_time, end_time, end_time - master->start_time);
/* Dump the current state of i2c registers */
rc = xscom_read(master->chip_id, master->xscom_base + I2C_CMD_REG,
&cmd);
if (rc) {
prlog(PR_DEBUG, "I2C: Failed to read CMD_REG\n");
cmd = 0ull;
}
rc = xscom_read(master->chip_id, master->xscom_base + I2C_MODE_REG,
&mode);
if (rc) {
prlog(PR_DEBUG, "I2C: Failed to read MODE_REG\n");
mode = 0ull;
}
rc = xscom_read(master->chip_id, master->xscom_base + I2C_STAT_REG,
&stat);
if (rc) {
prlog(PR_DEBUG, "I2C: Failed to read STAT_REG\n");
stat = 0ull;
}
rc = xscom_read(master->chip_id, master->xscom_base + I2C_EXTD_STAT_REG,
&estat);
if (rc) {
prlog(PR_DEBUG, "I2C: Failed to read EXTD_STAT_REG\n");
estat = 0ull;
}
rc = xscom_read(master->chip_id, master->xscom_base + I2C_INTR_MASK_REG,
&intm);
if (rc) {
prlog(PR_DEBUG, "I2C: Failed to read INTR_MASK_REG\n");
intm = 0ull;
}
rc = xscom_read(master->chip_id, master->xscom_base + I2C_INTR_COND_REG,
&intc);
if (rc) {
prlog(PR_DEBUG, "I2C: Failed to read INTR_COND_REG\n");
intc = 0ull;
}
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: Register dump--\n"
" cmd:0x%016llx\tmode:0x%016llx\tstat:0x%016llx\n"
" estat:0x%016llx\tintm:0x%016llx\tintc:0x%016llx\n",
cmd, mode, stat, estat, intm, intc);
}
static bool p8_i2c_has_irqs(struct p8_i2c_master *master)
{
struct proc_chip *chip;
/* Centaur I2C doesn't have interrupts */
if (master->type == I2C_CENTAUR)
return false;
chip = get_chip(master->chip_id);
/* The i2c interrupts was only added to Murano DD2.1 and Venice
* DD2.0. When operating without interrupts, we need to bump the
* timeouts as we rely solely on the polls from Linux which can
* be up to 2s apart !
*
* Also we don't have interrupts for the Centaur i2c.
*/
switch (chip->type) {
case PROC_CHIP_P8_MURANO:
return chip->ec_level >= 0x21;
case PROC_CHIP_P8_VENICE:
return chip->ec_level >= 0x20;
case PROC_CHIP_P8_NAPLES:
case PROC_CHIP_P9_NIMBUS:
case PROC_CHIP_P9_CUMULUS:
return true;
default:
return false;
}
}
static int p8_i2c_enable_irqs(struct p8_i2c_master *master)
{
int rc;
/* Enable the interrupts */
rc = xscom_write(master->chip_id, master->xscom_base +
I2C_INTR_COND_REG, I2C_STAT_ANY_ERR >> 16 |
I2C_INTR_CMD_COMP | I2C_INTR_DATA_REQ);
if (rc)
prlog(PR_ERR, "I2C: Failed to enable the interrupts\n");
return rc;
}
static void p8_i2c_reset_timeout(struct p8_i2c_master *master,
struct i2c_request *req)
{
struct p8_i2c_request *request;
uint64_t now = mftb();
master->last_update = now;
request = container_of(req, struct p8_i2c_request, req);
schedule_timer_at(&master->timeout, now + request->timeout);
}
static int p8_i2c_prog_watermark(struct p8_i2c_master *master)
{
uint64_t watermark;
int rc;
rc = xscom_read(master->chip_id, master->xscom_base + I2C_WATERMARK_REG,
&watermark);
if (rc) {
prlog(PR_ERR, "I2C: Failed to read the WATERMARK_REG\n");
return rc;
}
/* Set the high/low watermark */
watermark = SETFIELD(I2C_WATERMARK_HIGH, watermark, I2C_FIFO_HI_LVL);
watermark = SETFIELD(I2C_WATERMARK_LOW, watermark, I2C_FIFO_LO_LVL);
rc = xscom_write(master->chip_id, master->xscom_base +
I2C_WATERMARK_REG, watermark);
if (rc)
prlog(PR_ERR, "I2C: Failed to set high/low watermark level\n");
return rc;
}
static int p8_i2c_prog_mode(struct p8_i2c_master_port *port, bool enhanced_mode)
{
struct p8_i2c_master *master = port->master;
struct i2c_request *req = list_top(&master->req_list,
struct i2c_request, link);
struct p8_i2c_request *request =
container_of(req, struct p8_i2c_request, req);
uint64_t mode, omode;
int rc;
rc = xscom_read(master->chip_id, master->xscom_base +
I2C_MODE_REG, &mode);
if (rc) {
prlog(PR_ERR, "I2C: Failed to read the MODE_REG\n");
return rc;
}
omode = mode;
mode = SETFIELD(I2C_MODE_PORT_NUM, mode, request->port_num);
mode = SETFIELD(I2C_MODE_BIT_RATE_DIV, mode, port->bit_rate_div);
if (enhanced_mode)
mode |= I2C_MODE_ENHANCED;
else
mode &= ~I2C_MODE_ENHANCED;
if (mode == omode)
return 0;
rc = xscom_write(master->chip_id, master->xscom_base + I2C_MODE_REG,
mode);
if (rc)
prlog(PR_ERR, "I2C: Failed to write the MODE_REG\n");
return rc;
}
static void p8_i2c_complete_request(struct p8_i2c_master *master,
struct i2c_request *req, int ret)
{
struct p8_i2c_request *request =
container_of(req, struct p8_i2c_request, req);
/* We only complete the current top level request */
assert(req == list_top(&master->req_list, struct i2c_request, link));
cancel_timer_async(&master->timeout);
request->timeout = 0ul;
list_del(&req->link);
master->state = state_idle;
req->result = ret;
/* Schedule re-enabling of sensor cache */
if (master->occ_cache_dis)
schedule_timer(&master->sensor_cache,
msecs_to_tb(SENSOR_CACHE_EN_DELAY));
/* If we're done with i2c master, allow OCC to use it */
if (master->occ_lock_acquired && list_empty(&master->req_list))
occ_i2c_unlock(master);
unlock(&master->lock);
if (req->completion)
req->completion(ret, req);
/* req might have been freed at this point */
lock(&master->lock);
}
static int p8_i2c_engine_reset(struct p8_i2c_master_port *port)
{
struct p8_i2c_master *master = port->master;
int rc;
/* Reset the i2c engine */
rc = xscom_write(master->chip_id, master->xscom_base +
I2C_RESET_I2C_REG, 0);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_RESET), "I2C: Failed "
"to reset the i2c engine\n");
return rc;
}
/* Reprogram the watermark and mode */
rc = p8_i2c_prog_watermark(port->master);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_RESET), "I2C: Failed to"
"program the WATERMARK_REG\n");
return rc;
}
rc = p8_i2c_prog_mode(port, false);
if (rc)
log_simple_error(&e_info(OPAL_RC_I2C_RESET), "I2C: Failed to"
"program the MODE_REG\n");
return rc;
}
static void p8_i2c_translate_error(struct i2c_request *req, uint64_t status)
{
/* Assuming there are not more than one type of error simultaneously */
if (status & I2C_STAT_NACK_RCVD_ERR)
req->result = OPAL_I2C_NACK_RCVD;
else if (status & I2C_STAT_INVALID_CMD)
req->result = OPAL_I2C_INVALID_CMD;
else if (status & I2C_STAT_LBUS_PARITY_ERR)
req->result = OPAL_I2C_LBUS_PARITY;
else if (status & I2C_STAT_BKEND_OVERRUN_ERR)
req->result = OPAL_I2C_BKEND_OVERRUN;
else if (status & I2C_STAT_BKEND_ACCESS_ERR)
req->result = OPAL_I2C_BKEND_ACCESS;
else if (status & I2C_STAT_ARBT_LOST_ERR)
req->result = OPAL_I2C_ARBT_LOST;
else if (status & I2C_STAT_STOP_ERR)
req->result = OPAL_I2C_STOP_ERR;
else if (status & I2C_STAT_PSEUDO_TIMEOUT)
req->result = OPAL_I2C_TIMEOUT;
}
static int p8_i2c_reset_port(struct p8_i2c_master_port *p)
{
struct p8_i2c_master *master = p->master;
int reset_loops, rc;
uint64_t status;
/* FIXME: this should per per-port rather than per-master */
master->state = state_error;
/*
* Put the master into enhanced STOP mode when recovering the
* port. This causes the master to send additional STOP conditions
* to work around some particularly stupid I2C devices and it's
* required on secure I2C masters since they will not send a bare
* stop condition.
*/
rc = p8_i2c_prog_mode(p, true);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_RESET),
"I2C: Failed to enable enhanced mode\n");
return -1;
}
rc = xscom_write(master->chip_id, master->xscom_base +
I2C_CMD_REG, I2C_CMD_WITH_STOP);
if (rc)
goto err;
/* Wait for COMMAND COMPLETE */
for (reset_loops = 0; reset_loops < 10; reset_loops++) {
time_wait_ms(10);
rc = xscom_read(master->chip_id,
master->xscom_base + I2C_STAT_REG,
&status);
if (rc)
goto err;
if (status & I2C_STAT_CMD_COMP)
break;
}
if (status & I2C_STAT_CMD_COMP)
return 0;
err:
prerror("I2C: Failed to reset c%de%dp%d\n",
master->chip_id, master->engine_id, p->port_num);
return -1;
}
static void p8_i2c_status_error(struct p8_i2c_master_port *port,
struct i2c_request *req,
uint64_t status, uint64_t end_time)
{
struct p8_i2c_master *master = port->master;
int rc;
/* Display any error other than I2C_INTR_NACK_RCVD_ERR or
* timeout since getting NACK's is normal if Linux is probing
* the bus and timeouts will have already logged something.
*/
if (!(status & (I2C_STAT_NACK_RCVD_ERR | I2C_STAT_PSEUDO_TIMEOUT))) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER),
"I2C: Transfer error occurred\n");
p8_i2c_print_debug_info(port, req, end_time);
} else if (status == I2C_STAT_PSEUDO_TIMEOUT) {
log_simple_error(&e_info(OPAL_RC_I2C_TIMEOUT),
"I2C: request timed out!\n");
p8_i2c_print_debug_info(port, req, end_time);
}
p8_i2c_translate_error(req, status);
rc = p8_i2c_engine_reset(port);
if (rc)
goto exit;
if (status & (I2C_STAT_LBUS_PARITY_ERR | I2C_STAT_ARBT_LOST_ERR |
I2C_STAT_STOP_ERR)) {
/*
* Don't bother issuing a STOP command for those errors
* just get rid of the current request and start off with
* the fresh one in the list
*/
p8_i2c_complete_request(master, req, req->result);
} else {
if (p8_i2c_reset_port(port))
goto exit;
/* Enable the interrupt */
p8_i2c_enable_irqs(master);
}
return;
exit:
p8_i2c_complete_request(master, req, req->result);
}
static int p8_i2c_fifo_read(struct p8_i2c_master *master,
uint8_t *buf, uint32_t count)
{
uint64_t fifo;
uint32_t i;
int rc = 0;
for (i = 0; i < count; i++, buf++) {
rc = xscom_read(master->chip_id, master->xscom_base +
I2C_FIFO_REG, &fifo);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER),
"I2C: Failed to read the fifo\n");
break;
}
*buf = GETFIELD(I2C_FIFO, fifo);
}
return rc;
}
static int p8_i2c_fifo_write(struct p8_i2c_master *master,
uint8_t *buf, uint32_t count)
{
uint64_t fifo;
uint32_t i;
int rc = 0;
for (i = 0; i < count; i++, buf++) {
fifo = SETFIELD(I2C_FIFO, 0ull, *buf);
rc = xscom_write(master->chip_id, master->xscom_base +
I2C_FIFO_REG, fifo);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER),
"I2C: Failed to write the fifo\n");
break;
}
}
return rc;
}
static void p8_i2c_status_data_request(struct p8_i2c_master *master,
struct i2c_request *req,
uint64_t status)
{
uint32_t fifo_count, fifo_free, count;
uint8_t *buf;
int rc = 0;
fifo_count = GETFIELD(I2C_STAT_FIFO_ENTRY_COUNT, status);
fifo_free = master->fifo_size - fifo_count;
DBG("Data request, state=%d fifo_count=%d/%d bytes_sent=%d\n",
master->state, fifo_count, master->fifo_size, master->bytes_sent);
switch(master->state) {
case state_offset:
/* We assume the offset can always be written in one go */
if (fifo_free < req->offset_bytes) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER),
"I2C: Fifo too small for offset !\n");
rc = OPAL_HARDWARE;
} else {
rc = p8_i2c_fifo_write(master, master->obuf,
req->offset_bytes);
}
/* For read, wait address phase to complete */
if (rc || req->op != SMBUS_WRITE)
break;
/* For writes, transition to data phase now */
master->state = state_data;
fifo_free -= req->offset_bytes;
/* Fall through */
case state_data:
/* Sanity check */
if (master->bytes_sent >= req->rw_len) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: "
"Data req with no data to send sent=%d "
"req=%d\n", master->bytes_sent,
req->rw_len);
rc = OPAL_HARDWARE;
break;
}
/* Get next chunk */
buf = req->rw_buf + master->bytes_sent;
count = req->rw_len - master->bytes_sent;
/* Check direction */
if (req->op == I2C_READ || req->op == SMBUS_READ) {
if (count > fifo_count)
count = fifo_count;
rc = p8_i2c_fifo_read(master, buf, count);
} else {
if (count > fifo_free)
count = fifo_free;
rc = p8_i2c_fifo_write(master, buf, count);
}
if (rc == 0)
master->bytes_sent += count;
break;
default:
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: Invalid "
"state %d in data req !\n", master->state);
rc = OPAL_WRONG_STATE;
}
if (rc) {
p8_i2c_complete_request(master, req, rc);
} else {
p8_i2c_enable_irqs(master);
p8_i2c_reset_timeout(master, req);
}
}
static void p8_i2c_complete_offset(struct p8_i2c_master *master,
struct i2c_request *req)
{
uint64_t cmd;
int rc = 0;
DBG("Completing offset phase\n");
/* If it's a write, we should only get here for empty
* write commands
*/
if (req->op == SMBUS_WRITE && req->rw_len != 0) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: Write "
"completion in offset state !\n");
rc = OPAL_HARDWARE;
goto complete;
}
/* Switch to data phase */
master->state = state_data;
/* If it's not a read command, or there are no data to read,
* then we complete the command
*/
if (req->op != SMBUS_READ || req->rw_len == 0)
goto complete;
/* Otherwise, let's start the data phase */
cmd = I2C_CMD_WITH_START | I2C_CMD_WITH_ADDR |
I2C_CMD_WITH_STOP | I2C_CMD_READ_NOT_WRITE;
cmd = SETFIELD(I2C_CMD_DEV_ADDR, cmd, req->dev_addr);
cmd = SETFIELD(I2C_CMD_LEN_BYTES, cmd, req->rw_len);
cmd = SETFIELD(I2C_CMD_INTR_STEERING, cmd, I2C_CMD_INTR_STEER_HOST);
DBG("Command: %016llx, state: %d\n", cmd, master->state);
/* Send command */
rc = xscom_write(master->chip_id, master->xscom_base + I2C_CMD_REG,
cmd);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: Failed "
"to write the CMD_REG\n");
goto complete;
}
/* Enable the interrupts */
p8_i2c_enable_irqs(master);
p8_i2c_reset_timeout(master, req);
return;
complete:
p8_i2c_complete_request(master, req, rc);
}
static void p8_i2c_status_cmd_completion(struct p8_i2c_master *master,
struct i2c_request *req,
uint64_t end_time __unused)
{
int rc;
DBG("Command completion, state=%d bytes_sent=%d\n",
master->state, master->bytes_sent);
DBG(" start_time=%016llx end_time=%016llx (duration=%016llx)\n",
master->start_time, end_time, end_time - master->start_time);
/* If we complete an offset, we probably need to transition
* do a data read, check if that all makes sense
*/
if (master->state == state_offset) {
p8_i2c_complete_offset(master, req);
return;
}
/* If we are not already in error state, check if we have
* completed our data transfer properly
*/
if (master->state != state_error && master->bytes_sent != req->rw_len) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER), "I2C: Request "
"complete with residual data req=%d done=%d\n",
req->rw_len, master->bytes_sent);
/* Should we error out here ? */
}
rc = master->state == state_error ? req->result : OPAL_SUCCESS;
p8_i2c_complete_request(master, req, rc);
}
static void p8_i2c_check_status(struct p8_i2c_master *master)
{
struct p8_i2c_master_port *port;
struct p8_i2c_request *request;
uint64_t status, deadline, now;
struct i2c_request *req;
int rc;
/*
* When idle or waiting for the occ to release the bus there's
* nothing to check. Error states are handled when starting
* a new request.
*/
if (master->state == state_idle || master->state == state_occache_dis)
return;
/* A non-idle master should always have a pending request */
req = list_top(&master->req_list, struct i2c_request, link);
if (!req) {
prerror("I2C: Master is not idle and has no pending request\n");
return;
}
rc = i2cm_read_reg(master, I2C_STAT_REG, &status);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER),
"I2C: Failed to read the STAT_REG\n");
return;
}
/* Mask the interrupts for this engine */
rc = i2cm_write_reg(master, I2C_INTR_REG, ~I2C_INTR_ALL);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_TRANSFER),
"I2C: Failed to disable the interrupts\n");
return;
}
/* Get port for current request */
port = container_of(req->bus, struct p8_i2c_master_port, bus);
now = mftb();
request = container_of(req, struct p8_i2c_request, req);
deadline = master->last_update + request->timeout;
if (status & I2C_STAT_ANY_ERR)
p8_i2c_status_error(port, req, status & I2C_STAT_ANY_ERR, now);
else if (status & I2C_STAT_DATA_REQ)
p8_i2c_status_data_request(master, req, status);
else if (status & I2C_STAT_CMD_COMP)
p8_i2c_status_cmd_completion(master, req, now);
else if (tb_compare(now, deadline) == TB_AAFTERB)
p8_i2c_status_error(port, req, I2C_STAT_PSEUDO_TIMEOUT, now);
else
p8_i2c_enable_irqs(master);
}
static int p8_i2c_check_initial_status(struct p8_i2c_master_port *port)
{
struct p8_i2c_master *master = port->master;
uint64_t status, estat;
int rc;
master->recovery_pass++;
/* Read status register */
rc = xscom_read(master->chip_id, master->xscom_base + I2C_STAT_REG,
&status);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: Failed "
"to read the STAT_REG\n");
return rc;
}
rc = xscom_read(master->chip_id,
master->xscom_base + I2C_EXTD_STAT_REG,
&estat);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: Failed "
"to read the EXTD_STAT_REG\n");
return rc;
}
if (estat & (I2C_EXTD_STAT_I2C_BUSY | I2C_EXTD_STAT_SELF_BUSY)) {
DBG("Initial estat busy ! %016llx\n", estat);
/* Just a warning for now */
}
/* Nothing happened ? Go back */
if (status & I2C_STAT_ANY_ERR) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: "
"Initial error status 0x%016llx\n", status);
if (master->recovery_pass > 1) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: "
"Error stuck, aborting !!\n");
return OPAL_HARDWARE;
}
/* Mark state as "recovery" to block any other activity */
master->state = state_recovery;
/* Reset the engine */
p8_i2c_engine_reset(port);
/* Delay 5ms for bus to settle */
schedule_timer(&master->recovery, msecs_to_tb(5));
return OPAL_BUSY;
}
/* Still busy ? */
if (!(status & I2C_STAT_CMD_COMP)) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: Initial "
"command complete not set\n");
if (master->recovery_pass > 5) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: "
"Command stuck, aborting !!\n");
return OPAL_HARDWARE;
}
master->state = state_recovery;
/* Delay 5ms for bus to settle */
schedule_timer(&master->recovery, msecs_to_tb(5));
return OPAL_BUSY;
}
master->recovery_pass = 0;
return 0;
}
/*
* On POWER9, the I2C may also wish to use some of the i2cm engines,
* to do things like read sensor data. There's a couple of shared
* registers with the OCC to negotiate locking of the i2cm engines.
* See occ/src/occ_405/lock/lock.c
*/
static bool occ_uses_master(struct p8_i2c_master *master)
{
/* OCC uses I2CM Engines 1,2 and 3, only on POWER9 */
if (master->type == I2C_POWER8 && proc_gen == proc_gen_p9)
return master->engine_id >= 1;
return false;
}
#define OCCFLG_BASE 0x00000000006C08A
#define OCCFLG_CLEAR 0x00000000006C08B
#define OCCFLG_SET 0x00000000006C08C
static int occ_i2c_lock(struct p8_i2c_master *master)
{
u64 occflags, busflag;
int rc;
if (!occ_uses_master(master))
return 0;
if (master->occ_lock_acquired)
return 0;
rc = xscom_read(master->chip_id, OCCFLG_BASE, &occflags);
if (rc) {
prerror("I2C: Failed to read OCC FLAG register\n");
return rc;
}
assert(master->engine_id > 0);
busflag = PPC_BIT(16 + (master->engine_id - 1) * 2);
DBG("I2C: c%de%d: occflags = %llx (locks = %x:%x:%x)\n",
master->chip_id, master->engine_id, (u64) occflags,
(u32) GETFIELD(PPC_BITMASK(16, 17), occflags),
(u32) GETFIELD(PPC_BITMASK(18, 19), occflags),
(u32) GETFIELD(PPC_BITMASK(20, 21), occflags));
rc = xscom_write(master->chip_id, OCCFLG_SET, busflag);
if (rc) {
prerror("I2C: Failed to write OCC FLAG register\n");
return rc;
}
/* If the OCC also has this bus locked then wait for IRQ */
if (occflags & (busflag >> 1)) {
DBG("I2C: c%de%d: Master in use by OCC\n",
master->chip_id, master->engine_id);
return 1;
}
master->occ_lock_acquired = true;
return 0;
}
static int occ_i2c_unlock(struct p8_i2c_master *master)
{
u64 busflag, occflags;
int rc;
if (!occ_uses_master(master))
return 0;
rc = xscom_read(master->chip_id, OCCFLG_BASE, &occflags);
if (rc) {
prerror("I2C: Failed to read OCC Flag register\n");
return rc;
}
busflag = PPC_BIT(16 + (master->engine_id - 1) * 2);
if (!(occflags & busflag)) {
DBG("I2C: spurious unlock for c%de%d already cleared (flags = %.16llx)",
master->chip_id, master->engine_id, occflags);
}
rc = xscom_write(master->chip_id, OCCFLG_CLEAR, busflag);
if (rc)
prerror("I2C: Failed to write OCC Flag register\n");
master->occ_lock_acquired = false;
return rc;
}
static int p8_i2c_start_request(struct p8_i2c_master *master,
struct i2c_request *req)
{
struct p8_i2c_master_port *port;
struct p8_i2c_request *request =
container_of(req, struct p8_i2c_request, req);
uint64_t cmd, poll_interval;
int64_t rc;
DBG("Starting req %d len=%d addr=%02x (offset=%x)\n",
req->op, req->rw_len, req->dev_addr, req->offset);
/* Get port */
port = container_of(req->bus, struct p8_i2c_master_port, bus);
/* Check if we need to disable the OCC cache first */
if (master->type == I2C_CENTAUR && !master->occ_cache_dis) {
DBG("Disabling OCC cache...\n");
rc = centaur_disable_sensor_cache(master->chip_id);
if (rc < 0) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ),
"I2C: Failed "
"to disable the sensor cache\n");
return rc;
}
master->occ_cache_dis = true;
/* Do we need to wait ? */
if (rc > 0) {
DBG("Waiting %lld\n", rc);
master->state = state_occache_dis;
schedule_timer(&master->recovery, rc);
return 0;
}
}
/*
* on P9 we need to set the "I2C master using bit" so we don't
* conflict with the OCC's use of the i2c master.
*/
rc = occ_i2c_lock(master);
if (rc < 0) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ),
"I2C: Failed to get I2CM lock from OCC\n");
return rc;
}
if (rc > 0) {
/* Wait for OCC IRQ */
master->state = state_occache_dis;
schedule_timer(&master->recovery, msecs_to_tb(10));
return 0;
}
/* Convert the offset if needed */
if (req->offset_bytes) {
int i;
for (i = 0; i < req->offset_bytes; i++) {
uint8_t b;
b = req->offset >> (8 * (req->offset_bytes - i - 1));
master->obuf[i] = b;
}
DBG("Offset %d bytes: %02x %02x %02x %02x\n",
req->offset_bytes, master->obuf[0], master->obuf[1],
master->obuf[2], master->obuf[3]);
}
/* Program mode register */
rc = p8_i2c_prog_mode(port, false);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: Failed "
"to program the MODE_REG\n");
return rc;
}
/* Check status */
rc = p8_i2c_check_initial_status(port);
if (rc != OPAL_BUSY)
master->recovery_pass = 0;
if (rc)
return rc;
/* program the watermark register */
rc = p8_i2c_prog_watermark(master);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_INIT),
"I2C: Failed to program the WATERMARK_REG\n");
return rc;
}
/* Initialize bytes_sent */
master->bytes_sent = 0;
/* Set up the command register */
cmd = I2C_CMD_WITH_START | I2C_CMD_WITH_ADDR;
cmd = SETFIELD(I2C_CMD_DEV_ADDR, cmd, req->dev_addr);
cmd = SETFIELD(I2C_CMD_INTR_STEERING, cmd, I2C_CMD_INTR_STEER_HOST);
switch (req->op) {
case I2C_READ:
cmd |= I2C_CMD_READ_NOT_WRITE;
/* Fall through */
case I2C_WRITE:
cmd |= I2C_CMD_WITH_STOP;
cmd = SETFIELD(I2C_CMD_LEN_BYTES, cmd, req->rw_len);
master->state = state_data;
break;
case SMBUS_READ:
cmd = SETFIELD(I2C_CMD_LEN_BYTES, cmd, req->offset_bytes);
master->state = state_offset;
break;
case SMBUS_WRITE:
cmd |= I2C_CMD_WITH_STOP;
cmd = SETFIELD(I2C_CMD_LEN_BYTES, cmd,
req->rw_len + req->offset_bytes);
master->state = state_offset;
break;
default:
return OPAL_PARAMETER;
}
DBG("Command: %016llx, state: %d\n", cmd, master->state);
master->start_time = mftb();
/* Send command */
rc = xscom_write(master->chip_id, master->xscom_base + I2C_CMD_REG,
cmd);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_START_REQ), "I2C: Failed "
"to write the CMD_REG\n");
return rc;
}
/* Enable the interrupts */
p8_i2c_enable_irqs(master);
/* Run a poll timer for boot cases or non-working interrupts
* cases
*/
if (!opal_booting() && master->irq_ok)
poll_interval = TIMER_POLL;
else
poll_interval = master->poll_interval;
schedule_timer(&master->poller, poll_interval);
/* If we don't have a user-set timeout then use the master's default */
if (!request->timeout)
request->timeout = port->byte_timeout;
/* Start the timeout */
p8_i2c_reset_timeout(master, req);
return OPAL_SUCCESS;
}
static void p8_i2c_check_work(struct p8_i2c_master *master)
{
struct i2c_request *req;
int rc;
while (master->state == state_idle && !list_empty(&master->req_list)) {
req = list_top(&master->req_list, struct i2c_request, link);
rc = p8_i2c_start_request(master, req);
if (rc) {
/*
* If it didn't work the first three times then
* odds are it's not going to work on the 4th.
*/
if (rc && req->retries > 3)
p8_i2c_complete_request(master, req, rc);
else
req->retries++;
}
}
}
/* OCC IRQ Handler for I2C Ownership Change*/
void p9_i2c_bus_owner_change(u32 chip_id)
{
struct proc_chip *chip = get_chip(chip_id);
struct p8_i2c_master *master = NULL;
assert(chip);
list_for_each(&chip->i2cms, master, link) {
lock(&master->lock);
/* spurious */
if (master->state != state_occache_dis)
goto done;
/* Can we now lock this master? */
if (occ_i2c_lock(master))
goto done;
/* clear the existing wait timer */
cancel_timer_async(&master->recovery);
/* re-start the request now that we own the master */
master->state = state_idle;
p8_i2c_check_work(master);
p8_i2c_check_status(master);
done:
unlock(&master->lock);
}
}
static int p8_i2c_queue_request(struct i2c_request *req)
{
struct i2c_bus *bus = req->bus;
struct p8_i2c_master_port *port =
container_of(bus, struct p8_i2c_master_port, bus);
struct p8_i2c_master *master = port->master;
int rc = 0;
/* Parameter check */
if (req->rw_len > I2C_MAX_TFR_LEN) {
prlog(PR_ERR, "I2C: Too large transfer %d bytes\n", req->rw_len);
return OPAL_PARAMETER;
}
if (req->offset_bytes > 4) {
prlog(PR_ERR, "I2C: Invalid offset size %d\n", req->offset_bytes);
return OPAL_PARAMETER;
}
lock(&master->lock);
list_add_tail(&master->req_list, &req->link);
p8_i2c_check_work(master);
unlock(&master->lock);
return rc;
}
static struct i2c_request *p8_i2c_alloc_request(struct i2c_bus *bus)
{
struct p8_i2c_master_port *port =
container_of(bus, struct p8_i2c_master_port, bus);
struct p8_i2c_request *request;
request = zalloc(sizeof(*request));
if (!request) {
prlog(PR_ERR, "I2C: Failed to allocate i2c request\n");
return NULL;
}
request->port_num = port->port_num;
request->req.bus = bus;
return &request->req;
}
static void p8_i2c_free_request(struct i2c_request *req)
{
struct p8_i2c_request *request =
container_of(req, struct p8_i2c_request, req);
free(request);
}
static void p8_i2c_set_request_timeout(struct i2c_request *req,
uint64_t duration)
{
struct p8_i2c_request *request =
container_of(req, struct p8_i2c_request, req);
request->timeout = msecs_to_tb(duration);
}
static uint64_t p8_i2c_run_request(struct i2c_request *req)
{
struct i2c_bus *bus = req->bus;
struct p8_i2c_master_port *port =
container_of(bus, struct p8_i2c_master_port, bus);
struct p8_i2c_master *master = port->master;
uint64_t poll_interval = 0;
lock(&master->lock);
p8_i2c_check_status(master);
p8_i2c_check_work(master);
poll_interval = master->poll_interval;
unlock(&master->lock);
return poll_interval;
}
static inline uint32_t p8_i2c_get_bit_rate_divisor(uint32_t lb_freq,
uint32_t bus_speed)
{
assert(bus_speed > 0);
return (((lb_freq / bus_speed) - 1) / 4);
}
static inline uint64_t p8_i2c_get_poll_interval(uint32_t bus_speed)
{
uint64_t usec;
assert(bus_speed > 0);
/* Polling Interval = 8 * (1/bus_speed) * (1/10) -> convert to uSec */
usec = ((8 * USEC_PER_SEC) / (10 * bus_speed));
return usecs_to_tb(usec);
}
static void p8_i2c_timeout(struct timer *t __unused, void *data,
uint64_t __unused now)
{
struct p8_i2c_master *master = data;
lock(&master->lock);
DBG("timeout on c%de%d\n", master->chip_id, master->engine_id);
/*
* Run through the usual status checks. It's possible to get spurious
* timeouts due to races between the interrupt/poller paths and the
* timeout handler. So we do all the checking, all the time.
*/
p8_i2c_check_status(master);
p8_i2c_check_work(master);
unlock(&master->lock);
}
static void p8_i2c_recover(struct timer *t __unused, void *data,
uint64_t now __unused)
{
struct p8_i2c_master *master = data;
lock(&master->lock);
/*
* The recovery timer can race with the OCC interrupt. If the interrupt
* comes in just before this is called, then we'll get a spurious
* timeout which we need to ignore.
*/
if (master->state != state_recovery &&
master->state != state_occache_dis) {
unlock(&master->lock);
return;
}
master->state = state_idle;
/* We may or may not still have work pending, re-enable the sensor cache
* immediately if we don't (we just waited the recovery time so there is
* little point waiting longer).
*/
if (master->occ_cache_dis && list_empty(&master->req_list)) {
DBG("Re-enabling OCC cache after recovery\n");
centaur_enable_sensor_cache(master->chip_id);
master->occ_cache_dis = false;
}
if (master->occ_lock_acquired && list_empty(&master->req_list))
occ_i2c_unlock(master);
/* Re-check for new work */
p8_i2c_check_work(master);
unlock(&master->lock);
}
static void p8_i2c_enable_scache(struct timer *t __unused, void *data,
uint64_t now __unused)
{
struct p8_i2c_master *master = data;
lock(&master->lock);
/* Check if we are still idle */
if (master->state == state_idle && master->occ_cache_dis) {
DBG("Re-enabling OCC cache\n");
centaur_enable_sensor_cache(master->chip_id);
master->occ_cache_dis = false;
}
unlock(&master->lock);
}
static void p8_i2c_poll(struct timer *t __unused, void *data, uint64_t now)
{
struct p8_i2c_master *master = data;
/*
* This is called when the interrupt isn't functional or
* generally from the opal pollers, so fast while booting
* and slowly when Linux is up.
*/
/* Lockless fast bailout */
if (master->state == state_idle)
return;
lock(&master->lock);
p8_i2c_check_status(master);
if (master->state != state_idle)
schedule_timer_at(&master->poller, now + master->poll_interval);
p8_i2c_check_work(master);
unlock(&master->lock);
}
void p8_i2c_interrupt(uint32_t chip_id)
{
struct proc_chip *chip = get_chip(chip_id);
struct p8_i2c_master *master = NULL;
assert(chip);
list_for_each(&chip->i2cms, master, link) {
/* Lockless fast bailout (shared interrupt) */
if (master->state == state_idle)
continue;
lock(&master->lock);
/* Run the state machine */
p8_i2c_check_status(master);
/* Check for new work */
p8_i2c_check_work(master);
unlock(&master->lock);
}
}
static const char *compat[] = {
"ibm,power8-i2cm",
"ibm,centaur-i2cm"
};
static void p8_i2c_add_bus_prop(struct p8_i2c_master_port *port)
{
const struct dt_property *c, *p;
struct dt_node *np = port->bus.dt_node;
char name[32];
c = dt_find_property(np, "compatible");
p = dt_find_property(np, "ibm,port-name");
if (!c) {
if (port->master->type == I2C_POWER8)
dt_add_property_strings(np, "compatible",
"ibm,power8-i2c-port",
"ibm,opal-i2c");
else if (port->master->type == I2C_CENTAUR)
dt_add_property_strings(np, "compatible",
"ibm,centaur-i2c-port",
"ibm,opal-i2c");
}
if (!p) {
if (port->master->type == I2C_POWER8)
snprintf(name, sizeof(name), "p8_%08x_e%dp%d",
port->master->chip_id, port->master->engine_id,
port->port_num);
else if (port->master->type == I2C_CENTAUR)
snprintf(name, sizeof(name), "cen_%08x_e%dp%d",
port->master->chip_id, port->master->engine_id,
port->port_num);
dt_add_property_string(np, "ibm,port-name", name);
}
}
static void p8_i2c_init_one(struct dt_node *i2cm, enum p8_i2c_master_type type)
{
struct p8_i2c_master_port *port;
uint32_t lb_freq, count, max_bus_speed;
struct dt_node *i2cm_port;
struct p8_i2c_master *master;
struct list_head *chip_list;
uint64_t ex_stat, default_timeout;
static bool irq_printed;
int64_t rc;
master = zalloc(sizeof(*master));
if (!master) {
log_simple_error(&e_info(OPAL_RC_I2C_INIT),
"I2C: Failed to allocate master "
"structure\n");
return;
}
master->type = type;
/* Local bus speed in Hz */
lb_freq = dt_prop_get_u32(i2cm, "clock-frequency");
/* Initialise the i2c master structure */
master->state = state_idle;
master->chip_id = dt_get_chip_id(i2cm);
master->engine_id = dt_prop_get_u32(i2cm, "chip-engine#");
master->xscom_base = dt_get_address(i2cm, 0, NULL);
if (master->type == I2C_CENTAUR) {
struct centaur_chip *centaur = get_centaur(master->chip_id);
if (centaur == NULL) {
log_simple_error(&e_info(OPAL_RC_I2C_INIT),
"I2C: Failed to get centaur 0x%x ",
master->chip_id);
free(master);
return;
}
chip_list = &centaur->i2cms;
/* Detect bad device-tree from HostBoot giving us bogus
* i2c masters
*/
if (master->engine_id > 0) {
prlog(PR_ERR, "I2C: Skipping Centaur Master #1\n");
free(master);
return;
}
} else {
struct proc_chip *chip = get_chip(master->chip_id);
assert(chip);
chip_list = &chip->i2cms;
}
init_timer(&master->timeout, p8_i2c_timeout, master);
init_timer(&master->poller, p8_i2c_poll, master);
init_timer(&master->recovery, p8_i2c_recover, master);
init_timer(&master->sensor_cache, p8_i2c_enable_scache, master);
prlog(PR_INFO, "I2C: Chip %08x Eng. %d Clock %d Mhz\n",
master->chip_id, master->engine_id, lb_freq / 1000000);
/* Disable OCC cache during inits */
if (master->type == I2C_CENTAUR) {
rc = centaur_disable_sensor_cache(master->chip_id);
if (rc < 0) {
log_simple_error(&e_info(OPAL_RC_I2C_INIT), "I2C: "
"Error %lld disabling sensor cache\n",
rc);
/* Ignore error and move on ... */
} else
time_wait(rc);
}
rc = xscom_read(master->chip_id, master->xscom_base +
I2C_EXTD_STAT_REG, &ex_stat);
if (rc) {
log_simple_error(&e_info(OPAL_RC_I2C_INIT), "I2C: "
"Failed to read EXTD_STAT_REG\n");
if (master->type == I2C_CENTAUR)
centaur_enable_sensor_cache(master->chip_id);
free(master);
return;
}
master->fifo_size = GETFIELD(I2C_EXTD_STAT_FIFO_SIZE, ex_stat);
list_head_init(&master->req_list);
list_head_init(&master->ports);
/* Check if interrupt is usable */
master->irq_ok = p8_i2c_has_irqs(master);
if (!irq_printed) {
irq_printed = true;
prlog(PR_INFO, "I2C: Interrupts %sfunctional\n",
master->irq_ok ? "" : "non-");
}
/* Re-enable the sensor cache, we aren't touching HW anymore */
if (master->type == I2C_CENTAUR)
centaur_enable_sensor_cache(master->chip_id);
/* Allocate ports driven by this master */
count = 0;
dt_for_each_child(i2cm, i2cm_port)
count++;
port = zalloc(sizeof(*port) * count);
if (!port) {
log_simple_error(&e_info(OPAL_RC_I2C_INIT),
"I2C: Insufficient memory\n");
free(master);
return;
}
/* Add master to chip's list */
list_add_tail(chip_list, &master->link);
max_bus_speed = 0;
default_timeout = master->irq_ok ?
I2C_TIMEOUT_IRQ_MS :
I2C_TIMEOUT_POLL_MS;
dt_for_each_child(i2cm, i2cm_port) {
uint64_t timeout_ms;
uint32_t speed;
port->port_num = dt_prop_get_u32(i2cm_port, "reg");
port->master = master;
speed = dt_prop_get_u32(i2cm_port, "bus-frequency");
if (speed > max_bus_speed)
max_bus_speed = speed;
port->bit_rate_div =
p8_i2c_get_bit_rate_divisor(lb_freq, speed);
port->bus.dt_node = i2cm_port;
port->bus.queue_req = p8_i2c_queue_request;
port->bus.alloc_req = p8_i2c_alloc_request;
port->bus.free_req = p8_i2c_free_request;
port->bus.set_req_timeout = p8_i2c_set_request_timeout;
port->bus.run_req = p8_i2c_run_request;
timeout_ms = dt_prop_get_u32_def(i2cm_port, "timeout-ms",
default_timeout);
port->byte_timeout = msecs_to_tb(timeout_ms);
i2c_add_bus(&port->bus);
list_add_tail(&master->ports, &port->link);
/* Add OPAL properties to the bus node */
p8_i2c_add_bus_prop(port);
prlog(PR_INFO, " P%d: <%s> %d kHz\n",
port->port_num,
(char *)dt_prop_get(i2cm_port,
"ibm,port-name"), speed/1000);
port++;
}
/* When at runtime and we have the i2c irq, we just use it
* (see p8_i2c_start_request), but in the situation where
* one of those isn't the case (e.g. during boot), we need
* a better poll interval to efficiently crank the i2c machine.
* poll_interval is that interval.
*/
master->poll_interval = (max_bus_speed) ? p8_i2c_get_poll_interval(max_bus_speed) : TIMER_POLL;
}
void p8_i2c_init(void)
{
struct dt_node *i2cm;
int i;
for (i = 0; i < MAX_I2C_TYPE; i++) {
dt_for_each_compatible(dt_root, i2cm, compat[i])
p8_i2c_init_one(i2cm, i);
}
}