hw/npu2-hw-procedures.c

// SPDX-License-Identifier: Apache-2.0 OR GPL-2.0-or-later
/*
 * NPU2 (POWER9) Hardware Procedures
 *
 * Copyright 2013-2019 IBM Corp.
 */

#include <skiboot.h>
#include <io.h>
#include <timebase.h>
#include <pci.h>
#include <pci-virt.h>
#include <interrupts.h>
#include <npu2.h>
#include <npu2-regs.h>
#include <xscom.h>

/* Set in npu2.c if there is an nvram override for the zcal settings on this
 * machine */
int nv_zcal_nominal = -1;

/* PHY Registers. The documentation for the PHY training is written in
 * terms of bits within an actual register so we use that
 * representation here. */
struct npu2_phy_reg {
	uint64_t offset;
	uint64_t start;
	uint64_t len;
};

/*
 * Currently unused, but documented here:
static struct npu2_phy_reg NPU2_PHY_RX_DATA_DAC_SPARE_MODE = {0x000, 63, 64};
static struct npu2_phy_reg NPU2_PHY_RX_DAC_CNTL6	   = {0x00c, 63, 64};
static struct npu2_phy_reg NPU2_PHY_RX_DAC_CNTL5	   = {0x028, 63, 64};
static struct npu2_phy_reg NPU2_PHY_RX_DAC_CNTL9	   = {0x030, 63, 64};
static struct npu2_phy_reg NPU2_PHY_RX_DAC_CNTL5_EO	   = {0x00a, 63, 64};
static struct npu2_phy_reg NPU2_PHY_RX_DAC_CNTL4	   = {0x026, 63, 64};
*/
static struct npu2_phy_reg NPU2_PHY_RX_RUN_LANE		   = {0x0c8, 48, 1};
static struct npu2_phy_reg NPU2_PHY_RX_IORESET		   = {0x096, 63, 1};
static struct npu2_phy_reg NPU2_PHY_TX_IORESET		   = {0x113, 48, 1};
static struct npu2_phy_reg NPU2_PHY_RX_PR_RESET		   = {0x096, 62, 1};
static struct npu2_phy_reg NPU2_PHY_RX_LANE_ANA_PDWN	   = {0x002, 54, 1};
static struct npu2_phy_reg NPU2_PHY_RX_LANE_DIG_PDWN	   = {0x088, 48, 1};
static struct npu2_phy_reg NPU2_PHY_RX_PR_IQ_RES_SEL	   = {0x004, 59, 3};
static struct npu2_phy_reg NPU2_PHY_RX_PR_PHASE_STEP	   = {0x08a, 60, 4};
static struct npu2_phy_reg NPU2_PHY_TX_LANE_PDWN	   = {0x101, 48, 1};
static struct npu2_phy_reg NPU2_PHY_RX_RUN_DCCAL	   = {0x0c8, 49, 1};
static struct npu2_phy_reg NPU2_PHY_RX_DCCAL_DONE	   = {0x0ca, 49, 1};
static struct npu2_phy_reg NPU2_PHY_RX_LANE_BUSY	   = {0x0ca, 50, 1};
static struct npu2_phy_reg NPU2_PHY_RX_B_BANK_CONTROLS	   = {0x002, 58, 6};
static struct npu2_phy_reg NPU2_PHY_TX_UNLOAD_CLK_DISABLE  = {0x103, 56, 1};
static struct npu2_phy_reg NPU2_PHY_TX_FIFO_INIT	   = {0x105, 53, 1};
static struct npu2_phy_reg NPU2_PHY_TX_RXCAL		   = {0x103, 57, 1};
static struct npu2_phy_reg NPU2_PHY_RX_INIT_DONE	   = {0x0ca, 48, 1};
static struct npu2_phy_reg NPU2_PHY_RX_PR_EDGE_TRACK_CNTL  = {0x092, 48, 2};
static struct npu2_phy_reg NPU2_PHY_RX_PR_BUMP_SL_1UI	   = {0x092, 57, 1};
static struct npu2_phy_reg NPU2_PHY_RX_PR_FW_OFF	   = {0x08a, 56, 1};
static struct npu2_phy_reg NPU2_PHY_RX_PR_FW_INERTIA_AMT   = {0x08a, 57, 3};
static struct npu2_phy_reg NPU2_PHY_RX_CFG_LTE_MC	   = {0x000, 60, 4};
static struct npu2_phy_reg NPU2_PHY_RX_A_INTEG_COARSE_GAIN = {0x00a, 48, 4};
static struct npu2_phy_reg NPU2_PHY_RX_A_CTLE_COARSE	   = {0x00c, 48, 5};
static struct npu2_phy_reg NPU2_PHY_RX_A_CTLE_GAIN	   = {0x00c, 53, 4};
static struct npu2_phy_reg NPU2_PHY_RX_B_INTEG_COARSE_GAIN = {0x026, 48, 4};
static struct npu2_phy_reg NPU2_PHY_RX_B_CTLE_COARSE	   = {0x028, 48, 5};
static struct npu2_phy_reg NPU2_PHY_RX_B_CTLE_GAIN	   = {0x028, 53, 4};
static struct npu2_phy_reg NPU2_PHY_RX_E_INTEG_COARSE_GAIN = {0x030, 48, 4};
static struct npu2_phy_reg NPU2_PHY_RX_E_CTLE_COARSE	   = {0x032, 48, 5};
static struct npu2_phy_reg NPU2_PHY_RX_E_CTLE_GAIN	   = {0x032, 53, 4};

/* These registers are per-PHY, not per lane */
static struct npu2_phy_reg NPU2_PHY_RX_SPEED_SELECT	       = {0x262, 51, 2};
static struct npu2_phy_reg NPU2_PHY_RX_AC_COUPLED	       = {0x262, 53, 1};
static struct npu2_phy_reg NPU2_PHY_TX_ZCAL_SWO_EN	       = {0x3c9, 48, 1};
static struct npu2_phy_reg NPU2_PHY_TX_ZCAL_REQ		       = {0x3c1, 49, 1};
static struct npu2_phy_reg NPU2_PHY_TX_ZCAL_DONE	       = {0x3c1, 50, 1};
static struct npu2_phy_reg NPU2_PHY_TX_ZCAL_ERROR	       = {0x3c1, 51, 1};
static struct npu2_phy_reg NPU2_PHY_TX_ZCAL_N		       = {0x3c3, 48, 9};
static struct npu2_phy_reg NPU2_PHY_TX_ZCAL_P		       = {0x3c5, 48, 9};
static struct npu2_phy_reg NPU2_PHY_TX_FFE_BOOST_EN	       = {0x34b, 59, 1};
static struct npu2_phy_reg NPU2_PHY_TX_PSEG_PRE_EN	       = {0x34d, 51, 5};
static struct npu2_phy_reg NPU2_PHY_TX_PSEG_PRE_SELECT	       = {0x34d, 56, 5};
static struct npu2_phy_reg NPU2_PHY_TX_NSEG_PRE_EN	       = {0x34f, 51, 5};
static struct npu2_phy_reg NPU2_PHY_TX_NSEG_PRE_SELECT	       = {0x34f, 56, 5};
static struct npu2_phy_reg NPU2_PHY_TX_PSEG_POST_EN	       = {0x361, 49, 7};
static struct npu2_phy_reg NPU2_PHY_TX_PSEG_POST_SELECT        = {0x361, 56, 7};
static struct npu2_phy_reg NPU2_PHY_TX_NSEG_POST_EN	       = {0x363, 49, 7};
static struct npu2_phy_reg NPU2_PHY_TX_NSEG_POST_SELECT        = {0x363, 56, 7};
static struct npu2_phy_reg NPU2_PHY_TX_PSEG_MARGINPU_EN        = {0x351, 48, 8};
static struct npu2_phy_reg NPU2_PHY_TX_NSEG_MARGINPU_EN        = {0x353, 48, 8};
static struct npu2_phy_reg NPU2_PHY_TX_PSEG_MARGINPD_EN        = {0x351, 56, 8};
static struct npu2_phy_reg NPU2_PHY_TX_NSEG_MARGINPD_EN        = {0x353, 56, 8};
static struct npu2_phy_reg NPU2_PHY_TX_MARGINPU_SELECT	       = {0x355, 48, 8};
static struct npu2_phy_reg NPU2_PHY_TX_MARGINPD_SELECT	       = {0x355, 56, 8};
static struct npu2_phy_reg NPU2_PHY_TX_PSEG_MAIN_EN	       = {0x357, 51, 7};
static struct npu2_phy_reg NPU2_PHY_TX_NSEG_MAIN_EN	       = {0x359, 51, 7};
/* Currently unused, but documented here
static struct npu2_phy_reg NPU2_PHY_RX_HIST_MIN_EYE_WIDTH      = {0x24e, 54, 8};
static struct npu2_phy_reg NPU2_PHY_RX_HIST_MIN_EYE_WIDTH_LANE = {0x24e, 49, 5};
static struct npu2_phy_reg NPU2_PHY_RX_HIST_MIN_EYE_WIDTH_VALID= {0x24e, 48, 1};
*/
static struct npu2_phy_reg NPU2_PHY_RX_RC_ENABLE_AUTO_RECAL    = {0x25c, 51, 1};

static struct npu2_phy_reg NPU2_PHY_RX_CLKDIST_PDWN	       = {0x204, 48, 3};
static struct npu2_phy_reg NPU2_PHY_RX_IREF_PDWN	       = {0x230, 54, 1};
static struct npu2_phy_reg NPU2_PHY_TX_CLKDIST_PDWN	       = {0x305, 48, 3};
static struct npu2_phy_reg NPU2_PHY_RX_CTL_DATASM_CLKDIST_PDWN = {0x2e0, 60, 1};
static struct npu2_phy_reg NPU2_PHY_TX_DRV_DATA_PATTERN_GCRMSG = {0x309, 50, 4};

#define NPU2_PHY_REG(scom_base, reg, lane)					\
	SETFIELD(PPC_BITMASK(27, 31), ((reg)->offset << 42) | scom_base, lane)

#define NPU2_MAX_PHY_LANE			23

/* This is a bit of a gross hack but it does the job */
#define FOR_EACH_LANE(ndev, lane) \
	for (lane = 0; lane <= NPU2_MAX_PHY_LANE; lane++)	\
		if (!(ndev->lane_mask & (1 << (NPU2_MAX_PHY_LANE - lane)))) \
			continue;				\
		else

typedef uint32_t (*step)(struct npu2_dev *);

struct procedure {
	const char *name;
	step steps[];
};

#define DEFINE_PROCEDURE(NAME, STEPS...)		\
	static struct procedure procedure_##NAME =	\
	{.name = #NAME, .steps = {NAME, ##STEPS}}

#define PROCEDURE_INPROGRESS	(1 << 31)
#define PROCEDURE_COMPLETE	(1 << 30)
#define PROCEDURE_NEXT		(1 << 29)
#define PROCEDURE_FAILED	2
#define PROCEDURE_ABORTED 	3
#define PROCEDURE_UNSUPPORTED	4

/* Mask defining which status bits we want to expose */
#define PROCEDURE_STATUS_MASK	0xc000000f

static void phy_write_lane(struct npu2_dev *ndev, struct npu2_phy_reg *reg, int lane, uint64_t val)
{
	uint64_t old_val, reg_addr;
	int rc;
	uint64_t mask = PPC_BITMASK(reg->start, reg->start + reg->len - 1);

	/* Check to make sure we're not trying to specify a lane to a
	 * non-per-lane register */
	if (lane >= 0)
		assert(reg->offset < 0x200);
	else
		assert(reg->offset >= 0x200);

	reg_addr = NPU2_PHY_REG(ndev->pl_xscom_base, reg, lane);
	rc = xscom_read(ndev->npu->chip_id, reg_addr, &old_val);
	if (rc)
		NPU2DEVERR(ndev, "error %d reading scom 0x%llx\n", rc, reg_addr);
	val = SETFIELD(mask, old_val, val);
	rc = xscom_write(ndev->npu->chip_id, reg_addr, val);
	if (rc)
		NPU2DEVERR(ndev, "error %d writing scom 0x%llx\n", rc, reg_addr);
}

static uint64_t phy_read_lane(struct npu2_dev *ndev, struct npu2_phy_reg *reg, int lane)
{
	uint64_t val, reg_addr;
	int rc;
	uint64_t mask = PPC_BITMASK(reg->start, reg->start + reg->len - 1);

	/* Check to make sure we're not trying to specify a lane to a
	 * non-per-lane register */
	if (lane >= 0)
		assert(reg->offset < 0x200);
	else
		assert(reg->offset >= 0x200);

	reg_addr = NPU2_PHY_REG(ndev->pl_xscom_base, reg, lane);
	rc = xscom_read(ndev->npu->chip_id, reg_addr, &val);
	if (rc)
		NPU2DEVERR(ndev, "error %d reading scom 0x%llx\n", rc, reg_addr);

	return GETFIELD(mask, val);
}

#define phy_write(ndev, reg, val) phy_write_lane(ndev, reg, -1, val)
#define phy_read(ndev, reg) phy_read_lane(ndev, reg, -1)

static uint32_t stop(struct npu2_dev *npu_dev __unused)
{
	return PROCEDURE_COMPLETE | PROCEDURE_ABORTED;
}
DEFINE_PROCEDURE(stop);

static uint32_t nop(struct npu2_dev *npu_dev __unused)
{
	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(nop);

/*
 * Return the obus (0 or 1) of a device
 *
 * Using the brick index is dangerous, because it varies for a link
 * depending on the mode (opencapi or nvlink)
 */
static int obus_index(struct npu2_dev *ndev)
{
	if ((ndev->pl_xscom_base & 0x3F000000) == 0x09000000)
		return 0;
	else
		return 1;
}

/*
 * Return the brick number (0-2) within an obus chiplet.
 * Only valid for nvlink devices
 */
static int obus_brick_index(struct npu2_dev *ndev)
{
	int index = ndev->brick_index % 3;

	assert(ndev->type != NPU2_DEV_TYPE_OPENCAPI);
	/* On the second obus chiplet, index is reversed */
	if ((ndev->pl_xscom_base & 0x3F000000) != 0x09000000)
		return 2 - index;

	return index;
}

static void set_iovalid(struct npu2_dev *ndev, bool raise)
{
	uint64_t addr, val, mask;
	int rc;

	if (ndev->type == NPU2_DEV_TYPE_OPENCAPI)
		return;

	addr = (ndev->pl_xscom_base & 0x3F000000) | 0x9;
	mask = PPC_BIT(6 + obus_brick_index(ndev));
	val = raise ? mask : 0;

	rc = xscom_write_mask(ndev->npu->chip_id, addr, val, mask);
	if (rc)
		NPU2DEVERR(ndev, "error %d writing scom 0x%llx\n", rc, addr);
}

static bool poll_fence_status(struct npu2_dev *ndev, uint64_t val)
{
	uint64_t fs;
	int i;

	for (i = 0; i < 4096; i++) {
		fs = npu2_read(ndev->npu, NPU2_NTL_CQ_FENCE_STATUS(ndev));
		if ((fs & 0xc000000000000000UL) == val)
			return true;
	}

	NPU2DEVERR(ndev, "NPU2_NTL_CQ_FENCE_STATUS timeout (0x%llx)\n", val);
	return false;
}

/* Procedure 1.2.1 - Reset NPU/NDL */
uint32_t reset_ntl(struct npu2_dev *ndev)
{
	uint64_t val, check;
	int lane, i;

	set_iovalid(ndev, true);

	/* Power on clocks */
	phy_write(ndev, &NPU2_PHY_RX_CLKDIST_PDWN, 0);
	phy_write(ndev, &NPU2_PHY_RX_IREF_PDWN, 1);
	phy_write(ndev, &NPU2_PHY_TX_CLKDIST_PDWN, 0);
	phy_write(ndev, &NPU2_PHY_RX_CTL_DATASM_CLKDIST_PDWN, 0);

	FOR_EACH_LANE(ndev, lane) {
		phy_write_lane(ndev, &NPU2_PHY_RX_LANE_ANA_PDWN, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_RX_LANE_DIG_PDWN, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_TX_LANE_PDWN, lane, 0);
	}

	/* Clear fence state for the brick */
	val = npu2_read(ndev->npu, NPU2_MISC_FENCE_STATE);
	if (val) {
		NPU2DEVINF(ndev, "Clearing all bricks fence\n");
		npu2_write(ndev->npu, NPU2_MISC_FENCE_STATE, val);
		for (i = 0, check = 0; i < 4096; i++) {
			check = npu2_read(ndev->npu, NPU2_NTL_CQ_FENCE_STATUS(ndev));
			if (!check)
				break;
		}
		if (check)
			NPU2DEVERR(ndev, "Clearing NPU2_MISC_FENCE_STATE=0x%llx timeout, current=0x%llx\n",
					val, check);
	}

	/* Write PRI */
	val = SETFIELD(PPC_BITMASK(0,1), 0ull, obus_brick_index(ndev));
	npu2_write_mask(ndev->npu, NPU2_NTL_PRI_CFG(ndev), val, -1ULL);

	val = NPU2_NTL_MISC_CFG2_NDL_RX_PARITY_ENA;
	npu2_write_mask(ndev->npu, NPU2_NTL_MISC_CFG2(ndev), 0ull, val);

	/* NTL Reset */
	val = npu2_read(ndev->npu, NPU2_NTL_MISC_CFG1(ndev));
	val |= PPC_BIT(8) | PPC_BIT(9);
	npu2_write(ndev->npu, NPU2_NTL_MISC_CFG1(ndev), val);

	if (!poll_fence_status(ndev, 0xc000000000000000UL))
		return PROCEDURE_COMPLETE | PROCEDURE_FAILED;

	return PROCEDURE_NEXT;
}

static uint32_t reset_ndl(struct npu2_dev *ndev)
{
	uint64_t val;

	val = npu2_read_4b(ndev->npu, NPU2_NTL_DL_CONTROL(ndev));
	val |= PPC_BIT32(0) | PPC_BIT32(1);
	npu2_write_4b(ndev->npu, NPU2_NTL_DL_CONTROL(ndev), val);

	val = npu2_read_4b(ndev->npu, NPU2_NTL_DL_CONTROL(ndev));
	val &= ~(PPC_BIT32(0) | PPC_BIT32(1));
	npu2_write_4b(ndev->npu, NPU2_NTL_DL_CONTROL(ndev), val);

	val = PPC_BIT32(0);
	npu2_write_4b(ndev->npu, NPU2_NTL_DL_CONFIG(ndev), val);

	return PROCEDURE_NEXT;
}

static uint32_t reset_ntl_release(struct npu2_dev *ndev)
{
	uint64_t val;
	uint64_t npu2_fir;
	uint64_t npu2_fir_addr;
	int i;

	/* Clear FIR bits */
	npu2_fir_addr = NPU2_FIR_REGISTER_0;
	npu2_fir = 0;

	for (i = 0; i < NPU2_TOTAL_FIR_REGISTERS; i++) {
		xscom_write(ndev->npu->chip_id, npu2_fir_addr, npu2_fir);
		npu2_fir_addr += NPU2_FIR_OFFSET;

	}

	val = npu2_read(ndev->npu, NPU2_NTL_MISC_CFG1(ndev));
	val &= 0xFFBFFFFFFFFFFFFFUL;
	npu2_write(ndev->npu, NPU2_NTL_MISC_CFG1(ndev), val);

	if (!poll_fence_status(ndev, 0x8000000000000000UL))
		return PROCEDURE_COMPLETE | PROCEDURE_FAILED;

	return PROCEDURE_NEXT;
}

static uint32_t reset_ntl_finish(struct npu2_dev *ndev)
{
	/* Credit Setup */
	npu2_write(ndev->npu, NPU2_NTL_CRED_HDR_CREDIT_TX(ndev), 0x0200000000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_PRB_HDR_CREDIT_TX(ndev), 0x0200000000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_ATR_HDR_CREDIT_TX(ndev), 0x0200000000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_RSP_HDR_CREDIT_TX(ndev), 0x0200000000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_CRED_DATA_CREDIT_TX(ndev), 0x1000000000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_RSP_DATA_CREDIT_TX(ndev), 0x1000000000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_CRED_HDR_CREDIT_RX(ndev), 0x0000BE0000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_DBD_HDR_CREDIT_RX(ndev), 0x0000640000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_ATSD_HDR_CREDIT_RX(ndev), 0x0000200000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_RSP_HDR_CREDIT_RX(ndev), 0x0000BE0000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_CRED_DATA_CREDIT_RX(ndev), 0x0001000000000000UL);
	npu2_write(ndev->npu, NPU2_NTL_RSP_DATA_CREDIT_RX(ndev), 0x0001000000000000UL);

	npu2_set_link_flag(ndev, NPU2_DEV_DL_RESET);

	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(reset_ntl, reset_ndl, reset_ntl_release, reset_ntl_finish);

/* Procedure 1.2.2 - Reset I/O PHY Lanes */
static uint32_t phy_reset(struct npu2_dev *ndev)
{
	int lane;

	set_iovalid(ndev, false);

	/* Power on clocks */
	phy_write(ndev, &NPU2_PHY_RX_CLKDIST_PDWN, 0);
	phy_write(ndev, &NPU2_PHY_RX_IREF_PDWN, 1);
	phy_write(ndev, &NPU2_PHY_TX_CLKDIST_PDWN, 0);
	phy_write(ndev, &NPU2_PHY_RX_CTL_DATASM_CLKDIST_PDWN, 0);

	FOR_EACH_LANE(ndev, lane)
		phy_write_lane(ndev, &NPU2_PHY_RX_RUN_LANE, lane, 0);

	return PROCEDURE_NEXT;
}

static uint32_t phy_reset_wait(struct npu2_dev *ndev)
{
	int lane;

	/* Wait for all lanes to become inactive */
	FOR_EACH_LANE(ndev, lane)
		if (phy_read_lane(ndev, &NPU2_PHY_RX_LANE_BUSY, lane))
			return PROCEDURE_INPROGRESS;

	FOR_EACH_LANE(ndev, lane) {
		/* Set lane in reset */
		phy_write_lane(ndev, &NPU2_PHY_RX_IORESET, lane, 1);
		phy_write_lane(ndev, &NPU2_PHY_TX_IORESET, lane, 1);

		/* Release lane from reset */
		phy_write_lane(ndev, &NPU2_PHY_RX_IORESET, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_TX_IORESET, lane, 0);

		/* Reset the phase rotator */
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_RESET, lane, 1);
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_RESET, lane, 0);
	}

	return PROCEDURE_NEXT;
}

/* Procedure 1.2.3 - Initialise I/O PHY Registers */
static uint32_t phy_reset_complete(struct npu2_dev *ndev)
{
	int lane;

	FOR_EACH_LANE(ndev, lane) {
		phy_write_lane(ndev, &NPU2_PHY_RX_LANE_ANA_PDWN, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_RX_LANE_DIG_PDWN, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_IQ_RES_SEL, lane, 0x7);
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_PHASE_STEP, lane, 0xc);
		phy_write_lane(ndev, &NPU2_PHY_TX_LANE_PDWN, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_FW_INERTIA_AMT, lane, 4);
		phy_write_lane(ndev, &NPU2_PHY_RX_CFG_LTE_MC, lane, 3);
		phy_write_lane(ndev, &NPU2_PHY_RX_A_INTEG_COARSE_GAIN, lane, 11);
		phy_write_lane(ndev, &NPU2_PHY_RX_B_INTEG_COARSE_GAIN, lane, 11);
		phy_write_lane(ndev, &NPU2_PHY_RX_E_INTEG_COARSE_GAIN, lane, 11);

		if (ndev->type == NPU2_DEV_TYPE_OPENCAPI) {
			phy_write_lane(ndev, &NPU2_PHY_RX_A_CTLE_GAIN, lane, 0);
			phy_write_lane(ndev, &NPU2_PHY_RX_B_CTLE_GAIN, lane, 0);
			phy_write_lane(ndev, &NPU2_PHY_RX_E_CTLE_GAIN, lane, 0);

			phy_write_lane(ndev, &NPU2_PHY_RX_A_CTLE_COARSE, lane, 20);
			phy_write_lane(ndev, &NPU2_PHY_RX_B_CTLE_COARSE, lane, 20);
			phy_write_lane(ndev, &NPU2_PHY_RX_E_CTLE_COARSE, lane, 20);
		}
	}

	set_iovalid(ndev, true);

	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(phy_reset, phy_reset_wait, phy_reset_complete);

/* Procedure 1.2.6 - I/O PHY Tx Impedance Calibration */
static uint32_t phy_tx_zcal(struct npu2_dev *ndev)
{
	if (ndev->npu->tx_zcal_complete[obus_index(ndev)])
		return PROCEDURE_COMPLETE;

	/* Turn off SW enable and enable zcal state machine */
	phy_write(ndev, &NPU2_PHY_TX_ZCAL_SWO_EN, 0);

	/* Start impedance calibration state machine */
	phy_write(ndev, &NPU2_PHY_TX_ZCAL_REQ, 1);

	return PROCEDURE_NEXT;
}

static uint32_t phy_tx_zcal_wait(struct npu2_dev *ndev)
{
	int done, error;

	done = phy_read(ndev, &NPU2_PHY_TX_ZCAL_DONE);
	error = phy_read(ndev, &NPU2_PHY_TX_ZCAL_ERROR);

	/* We have never seen this in the field and it is not expected.
	 * Therefore it's best to error out which will complain loudly. Nominal
	 * vaules may be set in nvram to ignore this error. */
	if (error && nv_zcal_nominal < 0) {
		NPU2DEVERR(ndev, "ZCAL failed. Nominal values may be used by"
			   " setting nvram variable nv_zcal_override = 50\n");
		NPU2DEVERR(ndev, "However this may impact link performance\n");
		return PROCEDURE_COMPLETE | PROCEDURE_FAILED;
	}

	if (!done)
		return PROCEDURE_INPROGRESS;

	return PROCEDURE_NEXT;
}

#define MARGIN_RATIO		(0)
#define FFE_PRE_COEFF		(0)
#define FFE_POST_COEFF		(0)

#define PRE_WIDTH		(5)
#define POST_WIDTH		(7)
#define MAIN_WIDTH		(7)
#define ZCAL_MIN		(16 * 2)
#define ZCAL_MAX		(33 * 2)
#define PRECURSOR_X2_MAX	(4 * 2 + 1)
#define POSTCURSOR_X2_MAX	(6 * 2 + 1)
#define MARGIN_X2_MAX		(8 * 2)
#define MAIN_X2_MAX		((6 * 2) + 1)
#define TOTAL_X2_MAX		(PRECURSOR_X2_MAX + POSTCURSOR_X2_MAX + 2*MARGIN_X2_MAX + MAIN_X2_MAX)

static uint32_t therm(uint32_t dec)
{
	return ((0x1 << dec) - 1);
}

static uint32_t therm_with_half(uint32_t dec, uint8_t width)
{
	/* If the LSB of the 2r equivalent is on, then we need to set the 2r bit (MSB) */
	uint32_t half_on = ( dec & 0x1 ) << ( width - 1 );

	/* Shift the 2r equivalent to a 1r value and convert to a thermometer code. */
	uint32_t x1_equiv = ((1 << (dec >> 1 )) - 1);

	/* Combine 1r equivalent thermometer code + the 2r MSB value. */
	return half_on | x1_equiv;
}

static uint32_t phy_tx_zcal_calculate(struct npu2_dev *ndev)
{
	int p_value, n_value;
	int ffe_pre_coeff = FFE_PRE_COEFF;
	int ffe_post_coeff = FFE_POST_COEFF;
	uint32_t zcal_n;
	uint32_t zcal_p;
	uint32_t p_main_enable = MAIN_X2_MAX;
	uint32_t p_margin_pu_enable = MARGIN_X2_MAX;
	uint32_t p_margin_pd_enable = MARGIN_X2_MAX;
	uint32_t p_precursor_select;
	uint32_t p_postcursor_select;
	uint32_t margin_pu_select;
	uint32_t n_main_enable = MAIN_X2_MAX;
	uint32_t n_margin_pu_enable = MARGIN_X2_MAX;
	uint32_t n_margin_pd_enable = MARGIN_X2_MAX;
	uint32_t n_precursor_select;
	uint32_t n_postcursor_select;
	uint32_t margin_pd_select;
	uint32_t margin_select;

	if (nv_zcal_nominal < 0) {
		/* Convert the value from 8R to 2R by / 4 */
		zcal_n = phy_read(ndev, &NPU2_PHY_TX_ZCAL_N) / 4;
		zcal_p = phy_read(ndev, &NPU2_PHY_TX_ZCAL_P) / 4;
	} else {
		zcal_n = zcal_p = nv_zcal_nominal;
		NPU2DEVINF(ndev, "Using nominal values for zcal, performance may be impacted\n");
	}

	/* Again, if the hardware detects an unexpected condition it's
	 * better just to fail loudly. */
	if ((zcal_n < ZCAL_MIN) || (zcal_n > ZCAL_MAX) ||
	    (zcal_p < ZCAL_MIN) || (zcal_p > ZCAL_MAX))
		return PROCEDURE_COMPLETE | PROCEDURE_FAILED;

	if (ndev->type == NPU2_DEV_TYPE_OPENCAPI &&
	    platform.ocapi->phy_setup) {
		ffe_pre_coeff = platform.ocapi->phy_setup->tx_ffe_pre_coeff;
		ffe_post_coeff = platform.ocapi->phy_setup->tx_ffe_post_coeff;
	}

	p_value = zcal_p - TOTAL_X2_MAX;
	p_precursor_select = (p_value * ffe_pre_coeff)/128;
	p_postcursor_select = (p_value * ffe_post_coeff)/128;
	margin_pu_select = (p_value * MARGIN_RATIO)/256;

	if (p_value % 2) {
		p_main_enable--;
		p_value++;
	}

	while (p_value < 0) {
		if (p_main_enable > 1) {
			p_main_enable -= 2;
		} else if ((p_margin_pu_enable + p_margin_pd_enable) > 0) {
			if (p_margin_pu_enable == p_margin_pd_enable)
				p_margin_pd_enable -= 2;
			else
				p_margin_pu_enable -= 2;
		}
		p_value += 2;
	}

	n_value = zcal_n - TOTAL_X2_MAX;
	n_precursor_select = (n_value * ffe_pre_coeff)/128;
	n_postcursor_select = (n_value * ffe_post_coeff)/128;
	margin_pd_select = (p_value * MARGIN_RATIO)/256;

	if (n_value % 2) {
		n_main_enable--;
		n_value++;
	}

	while (n_value < 0) {
		if (n_main_enable > 1) {
			n_main_enable -= 2;
		} else if ((n_margin_pu_enable + n_margin_pd_enable) > 0) {
			if (n_margin_pu_enable == n_margin_pd_enable)
				n_margin_pd_enable -= 2;
			else
				n_margin_pu_enable -= 2;
		}
		n_value += 2;
	}

	margin_select = therm((margin_pu_select + 1)/2) &
		therm((margin_pd_select + 1)/2) &
		therm((p_margin_pu_enable + 1)/2) &
		therm((p_margin_pd_enable + 1)/2) &
		therm((n_margin_pu_enable + 1)/2) &
		therm((n_margin_pd_enable + 1)/2);

	phy_write(ndev, &NPU2_PHY_TX_PSEG_PRE_EN, therm_with_half(PRECURSOR_X2_MAX, PRE_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_PSEG_PRE_SELECT, therm_with_half(p_precursor_select, PRE_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_PSEG_POST_EN, therm_with_half(POSTCURSOR_X2_MAX, POST_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_PSEG_POST_SELECT, therm_with_half(p_postcursor_select, POST_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_PSEG_MARGINPU_EN, therm((p_margin_pu_enable + 1)/2));
	phy_write(ndev, &NPU2_PHY_TX_PSEG_MARGINPD_EN, therm((p_margin_pd_enable + 1)/2));
	phy_write(ndev, &NPU2_PHY_TX_PSEG_MAIN_EN, therm_with_half(p_main_enable, MAIN_WIDTH));

	phy_write(ndev, &NPU2_PHY_TX_NSEG_PRE_EN, therm_with_half(PRECURSOR_X2_MAX, PRE_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_NSEG_PRE_SELECT, therm_with_half(n_precursor_select, PRE_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_NSEG_POST_EN, therm_with_half(POSTCURSOR_X2_MAX, POST_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_NSEG_POST_SELECT, therm_with_half(n_postcursor_select, POST_WIDTH));
	phy_write(ndev, &NPU2_PHY_TX_NSEG_MARGINPU_EN, therm((n_margin_pu_enable + 1)/2));
	phy_write(ndev, &NPU2_PHY_TX_NSEG_MARGINPD_EN, therm((n_margin_pd_enable + 1)/2));
	phy_write(ndev, &NPU2_PHY_TX_NSEG_MAIN_EN, therm_with_half(n_main_enable, MAIN_WIDTH));

	phy_write(ndev, &NPU2_PHY_TX_MARGINPU_SELECT, therm(margin_select + 1)/2);
	phy_write(ndev, &NPU2_PHY_TX_MARGINPD_SELECT, therm(margin_select + 1)/2);

	ndev->npu->tx_zcal_complete[obus_index(ndev)] = 1;
	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(phy_tx_zcal, phy_tx_zcal_wait, phy_tx_zcal_calculate);

/* Procedure 1.2.8 - Enable Downstream Link Training */
static uint32_t phy_enable_tx_rxcal(struct npu2_dev *ndev)
{
	int lane;

	FOR_EACH_LANE(ndev, lane)
		phy_write_lane(ndev, &NPU2_PHY_TX_RXCAL, lane, 1);

	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(phy_enable_tx_rxcal);

/* Procedure 1.2.9 - Disable Downstream Link Training */
static uint32_t phy_disable_tx_rxcal(struct npu2_dev *ndev)
{
	int lane;

	FOR_EACH_LANE(ndev, lane)
		phy_write_lane(ndev, &NPU2_PHY_TX_RXCAL, lane, 0);

	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(phy_disable_tx_rxcal);

/* Procedure 1.2.4 - I/O PHY DC Calibration */
static uint32_t phy_rx_dccal(struct npu2_dev *ndev)
{
	int lane;

	set_iovalid(ndev, false);

	FOR_EACH_LANE(ndev, lane)
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_FW_OFF, lane, 1);

	FOR_EACH_LANE(ndev, lane)
		phy_write_lane(ndev, &NPU2_PHY_RX_RUN_DCCAL, lane, 1);

	return PROCEDURE_NEXT;
}

static uint32_t phy_rx_dccal_complete(struct npu2_dev *ndev)
{
	int lane;

	FOR_EACH_LANE(ndev, lane)
		if (!phy_read_lane(ndev, &NPU2_PHY_RX_DCCAL_DONE, lane))
			return PROCEDURE_INPROGRESS;

	FOR_EACH_LANE(ndev, lane)
		phy_write_lane(ndev, &NPU2_PHY_RX_RUN_DCCAL, lane, 0);

	FOR_EACH_LANE(ndev, lane) {
		phy_write_lane(ndev, &NPU2_PHY_RX_B_BANK_CONTROLS, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_EDGE_TRACK_CNTL, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_RX_PR_FW_OFF, lane, 0);
	}

	set_iovalid(ndev, true);

	return PROCEDURE_NEXT;
}

static uint32_t phy_rx_clock_sel(struct npu2_dev *ndev)
{
	if (ndev->type != NPU2_DEV_TYPE_OPENCAPI) {
		/*
		 * Change the RX clk mux control to be done by
		 * software instead of HW. This avoids glitches caused
		 * by changing the mux setting.
		 *
		 * Work around a known DL bug by doing these writes
		 * twice.
		 */
		npu2_write_mask_4b(ndev->npu, NPU2_NTL_DL_CLK_CTRL(ndev),
				0x80000002, 0x80000003);
		npu2_write_mask_4b(ndev->npu, NPU2_NTL_DL_CLK_CTRL(ndev),
				0x80000002, 0x80000003);

		npu2_write_mask_4b(ndev->npu, NPU2_NTL_DL_CLK_CTRL(ndev),
				0x80000000, 0x80000003);
		npu2_write_mask_4b(ndev->npu, NPU2_NTL_DL_CLK_CTRL(ndev),
				0x80000000, 0x80000003);
	}
	return PROCEDURE_NEXT;
}

/* Procedure 1.2.5 - IO PHY Tx FIFO Init */
static uint32_t phy_tx_fifo_init(struct npu2_dev *ndev)
{
	int lane;

	FOR_EACH_LANE(ndev, lane) {
		phy_write_lane(ndev, &NPU2_PHY_TX_UNLOAD_CLK_DISABLE, lane, 0);
		phy_write_lane(ndev, &NPU2_PHY_TX_FIFO_INIT, lane, 1);
		phy_write_lane(ndev, &NPU2_PHY_TX_UNLOAD_CLK_DISABLE, lane, 1);
	}

	return PROCEDURE_COMPLETE;
}

/* We group TX FIFO init in here mainly because that's what was done
 * on NVLink1 */
DEFINE_PROCEDURE(phy_rx_dccal, phy_rx_dccal_complete, phy_rx_clock_sel,
		 phy_tx_fifo_init);

/* Procedure 1.2.7 - I/O PHY Upstream Link Training */
static uint32_t phy_rx_training(struct npu2_dev *ndev)
{
	int lane;

	FOR_EACH_LANE(ndev, lane)
		phy_write_lane(ndev, &NPU2_PHY_RX_RUN_LANE, lane, 1);

	return PROCEDURE_NEXT;
}

static uint32_t phy_rx_training_wait(struct npu2_dev *ndev)
{
	int lane;

	FOR_EACH_LANE(ndev, lane)
		if (!phy_read_lane(ndev, &NPU2_PHY_RX_INIT_DONE, lane))
			return PROCEDURE_INPROGRESS;

	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(phy_rx_training, phy_rx_training_wait);

static uint32_t check_credit(struct npu2_dev *ndev, uint64_t reg,
			     const char *reg_name, uint64_t expected)
{
	uint64_t val;

	val = npu2_read(ndev->npu, reg);
	if (val == expected)
		return 0;

	NPU2DEVERR(ndev, "%s: expected 0x%llx, read 0x%llx\n",
		   reg_name, expected, val);

	return 1;
}

#define CHECK_CREDIT(ndev, reg, expected) \
	check_credit(ndev, reg(ndev), #reg, expected);

static uint32_t check_credits(struct npu2_dev *ndev)
{
	uint64_t val;

	CHECK_CREDIT(ndev, NPU2_NTL_CRED_HDR_CREDIT_RX, 0x0BE0BE0000000000ULL);
	CHECK_CREDIT(ndev, NPU2_NTL_RSP_HDR_CREDIT_RX, 0x0BE0BE0000000000ULL);
	CHECK_CREDIT(ndev, NPU2_NTL_CRED_DATA_CREDIT_RX, 0x1001000000000000ULL);
	CHECK_CREDIT(ndev, NPU2_NTL_RSP_DATA_CREDIT_RX, 0x1001000000000000ULL);
	CHECK_CREDIT(ndev, NPU2_NTL_DBD_HDR_CREDIT_RX, 0x0640640000000000ULL);
	CHECK_CREDIT(ndev, NPU2_NTL_ATSD_HDR_CREDIT_RX, 0x0200200000000000ULL);

	val = npu2_read(ndev->npu, NPU2_NTL_MISC_CFG1(ndev));
	val &= 0xFF3FFFFFFFFFFFFFUL;
	npu2_write(ndev->npu, NPU2_NTL_MISC_CFG1(ndev), val);

	if (!poll_fence_status(ndev, 0x0))
		return PROCEDURE_COMPLETE | PROCEDURE_FAILED;

	val = NPU2_NTL_MISC_CFG2_NDL_RX_PARITY_ENA;
	npu2_write_mask(ndev->npu, NPU2_NTL_MISC_CFG2(ndev), val, val);

	return PROCEDURE_COMPLETE;
}
DEFINE_PROCEDURE(check_credits);

static struct procedure *npu_procedures[] = {
	&procedure_stop,
	&procedure_nop,
	NULL,
	NULL,
	&procedure_phy_reset,
	&procedure_phy_tx_zcal,
	&procedure_phy_rx_dccal,
	&procedure_phy_enable_tx_rxcal,
	&procedure_phy_disable_tx_rxcal,
	&procedure_phy_rx_training,
	&procedure_reset_ntl,

	/* Place holders for pre-terminate and terminate procedures */
	&procedure_nop,
	&procedure_nop,
	&procedure_check_credits
};

/* Run a procedure step(s) and return status */
static uint32_t get_procedure_status(struct npu2_dev *dev)
{
	uint32_t result;
	uint16_t procedure = dev->procedure_number;
	uint16_t step = dev->procedure_step;
	const char *name = npu_procedures[procedure]->name;

	do {
		result = npu_procedures[procedure]->steps[step](dev);

		if (result & PROCEDURE_NEXT) {
			step++;
			NPU2DEVINF(dev, "Running procedure %s step %d\n", name, step);
		}
	} while (result & PROCEDURE_NEXT);

	dev->procedure_step = step;

	if (result & PROCEDURE_COMPLETE)
		NPU2DEVINF(dev, "Procedure %s complete\n", name);
	else if (mftb() > dev->procedure_tb + msecs_to_tb(1000)) {
		NPU2DEVINF(dev, "Procedure %s timed out\n", name);
		result = PROCEDURE_COMPLETE | PROCEDURE_FAILED;
	}

	/* Mask off internal state bits */
	dev->procedure_status = result & PROCEDURE_STATUS_MASK;

	return dev->procedure_status;
}

static int64_t npu_dev_procedure_read(struct npu2_dev *dev, uint32_t offset,
				      uint32_t size, uint32_t *data)
{
	int64_t rc = OPAL_SUCCESS;

	if (size != 4) {
		/* Short config reads are not supported */
		prlog(PR_ERR, "NPU%d: Short read of procedure register\n", npu2_dev_to_phb(dev)->opal_id);
		return OPAL_PARAMETER;
	}

	*data = 0;

	switch (offset) {
	case 0:
		/* Only run the procedure if not already complete */
		if (dev->procedure_status & PROCEDURE_COMPLETE)
			*data = dev->procedure_status;
		else
			*data = get_procedure_status(dev);

		break;

	case 4:
		*data = dev->procedure_number;
		break;

	default:
		prlog(PR_ERR, "NPU%d: Invalid vendor specific offset 0x%08x\n",
		      npu2_dev_to_phb(dev)->opal_id, offset);
		rc = OPAL_PARAMETER;
	}

	return rc;
}

static int64_t npu_dev_procedure_write(struct npu2_dev *dev, uint32_t offset,
				       uint32_t size, uint32_t data)
{
	const char *name;
	int64_t rc = OPAL_SUCCESS;

	if (size != 4) {
		/* Short config writes are not supported */
		prlog(PR_ERR, "NPU%d: Short read of procedure register\n",
		      npu2_dev_to_phb(dev)->opal_id);
		return OPAL_PARAMETER;
	}

	switch (offset) {
	case 0:
		/* We ignore writes to the status register */
		NPU2DEVINF(dev, "Ignoring writes to status register\n");
		break;

	case 4:
		if (data >= ARRAY_SIZE(npu_procedures) ||
		    !npu_procedures[data]) {
			NPU2DEVINF(dev, "Unsupported procedure number %d\n", data);
			dev->procedure_status = PROCEDURE_COMPLETE
				| PROCEDURE_UNSUPPORTED;
			break;
		}

		name = npu_procedures[data]->name;
		if (dev->procedure_number == data
		    && !(dev->procedure_status & PROCEDURE_COMPLETE))
			NPU2DEVINF(dev, "Restarting procedure %s\n", name);
		else
			NPU2DEVINF(dev, "Starting procedure %s\n", name);

		dev->procedure_status = PROCEDURE_INPROGRESS;
		dev->procedure_number = data;
		dev->procedure_step = 0;
		dev->procedure_tb = mftb();
		break;

	default:
		NPU2DEVINF(dev, "Invalid vendor specific offset 0x%08x\n", offset);
		rc = OPAL_PARAMETER;
	}

	return rc;
}

int64_t npu2_dev_procedure(void *dev, struct pci_cfg_reg_filter *pcrf,
			   uint32_t offset, uint32_t len, uint32_t *data,
			   bool write)
{
	struct pci_virt_device *pvd = dev;
	struct npu2_dev *ndev = pvd->data;

	if (write)
		return npu_dev_procedure_write(ndev, offset - pcrf->start,
					       len, *data);

	return npu_dev_procedure_read(ndev, offset - pcrf->start, len, data);
}

void npu2_dev_procedure_reset(struct npu2_dev *dev)
{
	uint64_t val;

	/* Fence the brick */
	val = npu2_read(dev->npu, NPU2_NTL_MISC_CFG1(dev));
	val |= PPC_BIT(8) | PPC_BIT(9);
	npu2_write(dev->npu, NPU2_NTL_MISC_CFG1(dev), val);

	npu2_clear_link_flag(dev, NPU2_DEV_DL_RESET);
}

static uint32_t run_procedure(struct npu2_dev *dev, uint16_t procedure_number)
{
	struct procedure *proc;
	const char *name;
	uint32_t result;

	assert(procedure_number <= ARRAY_SIZE(npu_procedures));
	proc = npu_procedures[procedure_number];
	assert(proc);

	name = proc->name;
	NPU2DEVINF(dev, "Running procedure %s\n", name);
	dev->procedure_status = PROCEDURE_INPROGRESS;
	dev->procedure_number = procedure_number;
	dev->procedure_step = 0;
	dev->procedure_tb = mftb();

	result = get_procedure_status(dev);
	while (!(result & PROCEDURE_COMPLETE)) {
		time_wait_ms(1);
		result = get_procedure_status(dev);
	}
	return result;
}

void npu2_opencapi_bump_ui_lane(struct npu2_dev *dev)
{
	uint64_t reg;
	uint64_t status_xscom;
	int lane, bit = 7;

	status_xscom = OB_ODL_TRAINING_STATUS(dev->brick_index);
	xscom_read(dev->npu->chip_id, status_xscom, &reg);
	reg = GETFIELD(OB_ODL_TRAINING_STATUS_STS_RX_PATTERN_B, reg);

	FOR_EACH_LANE(dev, lane) {
		if (reg & (1 << bit--))
			continue;
		prlog(PR_TRACE, "OCAPI: bumpui bumping lane %d\n", lane);
		for (int i = 0; i < 4; i++) {
			phy_write_lane(dev, &NPU2_PHY_RX_PR_BUMP_SL_1UI, lane, 1);
			phy_write_lane(dev, &NPU2_PHY_RX_PR_BUMP_SL_1UI, lane, 0);
		}
	}
}

void npu2_opencapi_phy_init(struct npu2_dev *dev)
{
	if (platform.ocapi->phy_setup) {
		OCAPIINF(dev, "Enabling platform-specific PHY setup\n");
		phy_write(dev, &NPU2_PHY_TX_FFE_BOOST_EN,
			  platform.ocapi->phy_setup->tx_ffe_boost_en);
	}

	run_procedure(dev, 5); /* procedure_phy_tx_zcal */
	/*
	 * This is only required for OpenCAPI - Hostboot tries to set this
	 * on systems where it can tell a link is OpenCAPI, but for
	 * Witherspoon it needs to be done in skiboot after device detection.
	 */
	phy_write(dev, &NPU2_PHY_RX_RC_ENABLE_AUTO_RECAL, 0x1);
	phy_write(dev, &NPU2_PHY_RX_AC_COUPLED, 1);

	switch (dev->link_speed) {
	case 20000000000UL:
		OCAPIINF(dev, "Link speed set at 20Gb/s\n");
		phy_write(dev, &NPU2_PHY_RX_SPEED_SELECT, 1);
		break;
	case 25000000000UL:
	case 25781250000UL:
		OCAPIINF(dev, "Link speed set at 25.xGb/s\n");
		phy_write(dev, &NPU2_PHY_RX_SPEED_SELECT, 0);
		break;
	default:
		OCAPIERR(dev, "Invalid link speed!\n");
		assert(false);
	}
}

int npu2_opencapi_phy_reset(struct npu2_dev *dev)
{
	int rc;

	rc = run_procedure(dev, 4); /* procedure_phy_reset */
	if (rc != PROCEDURE_COMPLETE)
		return -1;
	rc = run_procedure(dev, 6); /* procedure_phy_rx_dccal */
	if (rc != PROCEDURE_COMPLETE)
		return -1;
	return 0;
}

void npu2_opencapi_phy_prbs31(struct npu2_dev *dev)
{
	phy_write(dev, &NPU2_PHY_TX_DRV_DATA_PATTERN_GCRMSG, 0xD);
}