| /* |
| * QTests for the Xilinx ZynqMP CAN controller. |
| * |
| * Copyright (c) 2020 Xilinx Inc. |
| * |
| * Written-by: Vikram Garhwal<fnu.vikram@xilinx.com> |
| * |
| * Permission is hereby granted, free of charge, to any person obtaining a copy |
| * of this software and associated documentation files (the "Software"), to deal |
| * in the Software without restriction, including without limitation the rights |
| * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell |
| * copies of the Software, and to permit persons to whom the Software is |
| * furnished to do so, subject to the following conditions: |
| * |
| * The above copyright notice and this permission notice shall be included in |
| * all copies or substantial portions of the Software. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR |
| * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, |
| * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL |
| * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER |
| * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, |
| * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN |
| * THE SOFTWARE. |
| */ |
| |
| #include "qemu/osdep.h" |
| #include "libqtest.h" |
| |
| /* Base address. */ |
| #define CAN0_BASE_ADDR 0xFF060000 |
| #define CAN1_BASE_ADDR 0xFF070000 |
| |
| /* Register addresses. */ |
| #define R_SRR_OFFSET 0x00 |
| #define R_MSR_OFFSET 0x04 |
| #define R_SR_OFFSET 0x18 |
| #define R_ISR_OFFSET 0x1C |
| #define R_ICR_OFFSET 0x24 |
| #define R_TXID_OFFSET 0x30 |
| #define R_TXDLC_OFFSET 0x34 |
| #define R_TXDATA1_OFFSET 0x38 |
| #define R_TXDATA2_OFFSET 0x3C |
| #define R_RXID_OFFSET 0x50 |
| #define R_RXDLC_OFFSET 0x54 |
| #define R_RXDATA1_OFFSET 0x58 |
| #define R_RXDATA2_OFFSET 0x5C |
| #define R_AFR 0x60 |
| #define R_AFMR1 0x64 |
| #define R_AFIR1 0x68 |
| #define R_AFMR2 0x6C |
| #define R_AFIR2 0x70 |
| #define R_AFMR3 0x74 |
| #define R_AFIR3 0x78 |
| #define R_AFMR4 0x7C |
| #define R_AFIR4 0x80 |
| |
| /* CAN modes. */ |
| #define CONFIG_MODE 0x00 |
| #define NORMAL_MODE 0x00 |
| #define LOOPBACK_MODE 0x02 |
| #define SNOOP_MODE 0x04 |
| #define SLEEP_MODE 0x01 |
| #define ENABLE_CAN (1 << 1) |
| #define STATUS_NORMAL_MODE (1 << 3) |
| #define STATUS_LOOPBACK_MODE (1 << 1) |
| #define STATUS_SNOOP_MODE (1 << 12) |
| #define STATUS_SLEEP_MODE (1 << 2) |
| #define ISR_TXOK (1 << 1) |
| #define ISR_RXOK (1 << 4) |
| |
| static void match_rx_tx_data(const uint32_t *buf_tx, const uint32_t *buf_rx, |
| uint8_t can_timestamp) |
| { |
| uint16_t size = 0; |
| uint8_t len = 4; |
| |
| while (size < len) { |
| if (R_RXID_OFFSET + 4 * size == R_RXDLC_OFFSET) { |
| g_assert_cmpint(buf_rx[size], ==, buf_tx[size] + can_timestamp); |
| } else { |
| g_assert_cmpint(buf_rx[size], ==, buf_tx[size]); |
| } |
| |
| size++; |
| } |
| } |
| |
| static void read_data(QTestState *qts, uint64_t can_base_addr, uint32_t *buf_rx) |
| { |
| uint32_t int_status; |
| |
| /* Read the interrupt on CAN rx. */ |
| int_status = qtest_readl(qts, can_base_addr + R_ISR_OFFSET) & ISR_RXOK; |
| |
| g_assert_cmpint(int_status, ==, ISR_RXOK); |
| |
| /* Read the RX register data for CAN. */ |
| buf_rx[0] = qtest_readl(qts, can_base_addr + R_RXID_OFFSET); |
| buf_rx[1] = qtest_readl(qts, can_base_addr + R_RXDLC_OFFSET); |
| buf_rx[2] = qtest_readl(qts, can_base_addr + R_RXDATA1_OFFSET); |
| buf_rx[3] = qtest_readl(qts, can_base_addr + R_RXDATA2_OFFSET); |
| |
| /* Clear the RX interrupt. */ |
| qtest_writel(qts, CAN1_BASE_ADDR + R_ICR_OFFSET, ISR_RXOK); |
| } |
| |
| static void send_data(QTestState *qts, uint64_t can_base_addr, |
| const uint32_t *buf_tx) |
| { |
| uint32_t int_status; |
| |
| /* Write the TX register data for CAN. */ |
| qtest_writel(qts, can_base_addr + R_TXID_OFFSET, buf_tx[0]); |
| qtest_writel(qts, can_base_addr + R_TXDLC_OFFSET, buf_tx[1]); |
| qtest_writel(qts, can_base_addr + R_TXDATA1_OFFSET, buf_tx[2]); |
| qtest_writel(qts, can_base_addr + R_TXDATA2_OFFSET, buf_tx[3]); |
| |
| /* Read the interrupt on CAN for tx. */ |
| int_status = qtest_readl(qts, can_base_addr + R_ISR_OFFSET) & ISR_TXOK; |
| |
| g_assert_cmpint(int_status, ==, ISR_TXOK); |
| |
| /* Clear the interrupt for tx. */ |
| qtest_writel(qts, CAN0_BASE_ADDR + R_ICR_OFFSET, ISR_TXOK); |
| } |
| |
| /* |
| * This test will be transferring data from CAN0 and CAN1 through canbus. CAN0 |
| * initiate the data transfer to can-bus, CAN1 receives the data. Test compares |
| * the data sent from CAN0 with received on CAN1. |
| */ |
| static void test_can_bus(void) |
| { |
| const uint32_t buf_tx[4] = { 0xFF, 0x80000000, 0x12345678, 0x87654321 }; |
| uint32_t buf_rx[4] = { 0x00, 0x00, 0x00, 0x00 }; |
| uint32_t status = 0; |
| uint8_t can_timestamp = 1; |
| |
| QTestState *qts = qtest_init("-machine xlnx-zcu102" |
| " -object can-bus,id=canbus" |
| " -machine canbus0=canbus" |
| " -machine canbus1=canbus" |
| ); |
| |
| /* Configure the CAN0 and CAN1. */ |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_MSR_OFFSET, NORMAL_MODE); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_MSR_OFFSET, NORMAL_MODE); |
| |
| /* Check here if CAN0 and CAN1 are in normal mode. */ |
| status = qtest_readl(qts, CAN0_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_NORMAL_MODE); |
| |
| status = qtest_readl(qts, CAN1_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_NORMAL_MODE); |
| |
| send_data(qts, CAN0_BASE_ADDR, buf_tx); |
| |
| read_data(qts, CAN1_BASE_ADDR, buf_rx); |
| match_rx_tx_data(buf_tx, buf_rx, can_timestamp); |
| |
| qtest_quit(qts); |
| } |
| |
| /* |
| * This test is performing loopback mode on CAN0 and CAN1. Data sent from TX of |
| * each CAN0 and CAN1 are compared with RX register data for respective CAN. |
| */ |
| static void test_can_loopback(void) |
| { |
| uint32_t buf_tx[4] = { 0xFF, 0x80000000, 0x12345678, 0x87654321 }; |
| uint32_t buf_rx[4] = { 0x00, 0x00, 0x00, 0x00 }; |
| uint32_t status = 0; |
| |
| QTestState *qts = qtest_init("-machine xlnx-zcu102" |
| " -object can-bus,id=canbus" |
| " -machine canbus0=canbus" |
| " -machine canbus1=canbus" |
| ); |
| |
| /* Configure the CAN0 in loopback mode. */ |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, CONFIG_MODE); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_MSR_OFFSET, LOOPBACK_MODE); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| |
| /* Check here if CAN0 is set in loopback mode. */ |
| status = qtest_readl(qts, CAN0_BASE_ADDR + R_SR_OFFSET); |
| |
| g_assert_cmpint(status, ==, STATUS_LOOPBACK_MODE); |
| |
| send_data(qts, CAN0_BASE_ADDR, buf_tx); |
| read_data(qts, CAN0_BASE_ADDR, buf_rx); |
| match_rx_tx_data(buf_tx, buf_rx, 0); |
| |
| /* Configure the CAN1 in loopback mode. */ |
| qtest_writel(qts, CAN1_BASE_ADDR + R_SRR_OFFSET, CONFIG_MODE); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_MSR_OFFSET, LOOPBACK_MODE); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| |
| /* Check here if CAN1 is set in loopback mode. */ |
| status = qtest_readl(qts, CAN1_BASE_ADDR + R_SR_OFFSET); |
| |
| g_assert_cmpint(status, ==, STATUS_LOOPBACK_MODE); |
| |
| send_data(qts, CAN1_BASE_ADDR, buf_tx); |
| read_data(qts, CAN1_BASE_ADDR, buf_rx); |
| match_rx_tx_data(buf_tx, buf_rx, 0); |
| |
| qtest_quit(qts); |
| } |
| |
| /* |
| * Enable filters for CAN1. This will filter incoming messages with ID. In this |
| * test message will pass through filter 2. |
| */ |
| static void test_can_filter(void) |
| { |
| uint32_t buf_tx[4] = { 0x14, 0x80000000, 0x12345678, 0x87654321 }; |
| uint32_t buf_rx[4] = { 0x00, 0x00, 0x00, 0x00 }; |
| uint32_t status = 0; |
| uint8_t can_timestamp = 1; |
| |
| QTestState *qts = qtest_init("-machine xlnx-zcu102" |
| " -object can-bus,id=canbus" |
| " -machine canbus0=canbus" |
| " -machine canbus1=canbus" |
| ); |
| |
| /* Configure the CAN0 and CAN1. */ |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_MSR_OFFSET, NORMAL_MODE); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_MSR_OFFSET, NORMAL_MODE); |
| |
| /* Check here if CAN0 and CAN1 are in normal mode. */ |
| status = qtest_readl(qts, CAN0_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_NORMAL_MODE); |
| |
| status = qtest_readl(qts, CAN1_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_NORMAL_MODE); |
| |
| /* Set filter for CAN1 for incoming messages. */ |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFR, 0x0); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFMR1, 0xF7); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFIR1, 0x121F); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFMR2, 0x5431); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFIR2, 0x14); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFMR3, 0x1234); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFIR3, 0x5431); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFMR4, 0xFFF); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFIR4, 0x1234); |
| |
| qtest_writel(qts, CAN1_BASE_ADDR + R_AFR, 0xF); |
| |
| send_data(qts, CAN0_BASE_ADDR, buf_tx); |
| |
| read_data(qts, CAN1_BASE_ADDR, buf_rx); |
| match_rx_tx_data(buf_tx, buf_rx, can_timestamp); |
| |
| qtest_quit(qts); |
| } |
| |
| /* Testing sleep mode on CAN0 while CAN1 is in normal mode. */ |
| static void test_can_sleepmode(void) |
| { |
| uint32_t buf_tx[4] = { 0x14, 0x80000000, 0x12345678, 0x87654321 }; |
| uint32_t buf_rx[4] = { 0x00, 0x00, 0x00, 0x00 }; |
| uint32_t status = 0; |
| uint8_t can_timestamp = 1; |
| |
| QTestState *qts = qtest_init("-machine xlnx-zcu102" |
| " -object can-bus,id=canbus" |
| " -machine canbus0=canbus" |
| " -machine canbus1=canbus" |
| ); |
| |
| /* Configure the CAN0. */ |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, CONFIG_MODE); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_MSR_OFFSET, SLEEP_MODE); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| |
| qtest_writel(qts, CAN1_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_MSR_OFFSET, NORMAL_MODE); |
| |
| /* Check here if CAN0 is in SLEEP mode and CAN1 in normal mode. */ |
| status = qtest_readl(qts, CAN0_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_SLEEP_MODE); |
| |
| status = qtest_readl(qts, CAN1_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_NORMAL_MODE); |
| |
| send_data(qts, CAN1_BASE_ADDR, buf_tx); |
| |
| /* |
| * Once CAN1 sends data on can-bus. CAN0 should exit sleep mode. |
| * Check the CAN0 status now. It should exit the sleep mode and receive the |
| * incoming data. |
| */ |
| status = qtest_readl(qts, CAN0_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_NORMAL_MODE); |
| |
| read_data(qts, CAN0_BASE_ADDR, buf_rx); |
| |
| match_rx_tx_data(buf_tx, buf_rx, can_timestamp); |
| |
| qtest_quit(qts); |
| } |
| |
| /* Testing Snoop mode on CAN0 while CAN1 is in normal mode. */ |
| static void test_can_snoopmode(void) |
| { |
| uint32_t buf_tx[4] = { 0x14, 0x80000000, 0x12345678, 0x87654321 }; |
| uint32_t buf_rx[4] = { 0x00, 0x00, 0x00, 0x00 }; |
| uint32_t status = 0; |
| uint8_t can_timestamp = 1; |
| |
| QTestState *qts = qtest_init("-machine xlnx-zcu102" |
| " -object can-bus,id=canbus" |
| " -machine canbus0=canbus" |
| " -machine canbus1=canbus" |
| ); |
| |
| /* Configure the CAN0. */ |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, CONFIG_MODE); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_MSR_OFFSET, SNOOP_MODE); |
| qtest_writel(qts, CAN0_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| |
| qtest_writel(qts, CAN1_BASE_ADDR + R_SRR_OFFSET, ENABLE_CAN); |
| qtest_writel(qts, CAN1_BASE_ADDR + R_MSR_OFFSET, NORMAL_MODE); |
| |
| /* Check here if CAN0 is in SNOOP mode and CAN1 in normal mode. */ |
| status = qtest_readl(qts, CAN0_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_SNOOP_MODE); |
| |
| status = qtest_readl(qts, CAN1_BASE_ADDR + R_SR_OFFSET); |
| g_assert_cmpint(status, ==, STATUS_NORMAL_MODE); |
| |
| send_data(qts, CAN1_BASE_ADDR, buf_tx); |
| |
| read_data(qts, CAN0_BASE_ADDR, buf_rx); |
| |
| match_rx_tx_data(buf_tx, buf_rx, can_timestamp); |
| |
| qtest_quit(qts); |
| } |
| |
| int main(int argc, char **argv) |
| { |
| g_test_init(&argc, &argv, NULL); |
| |
| qtest_add_func("/net/can/can_bus", test_can_bus); |
| qtest_add_func("/net/can/can_loopback", test_can_loopback); |
| qtest_add_func("/net/can/can_filter", test_can_filter); |
| qtest_add_func("/net/can/can_test_snoopmode", test_can_snoopmode); |
| qtest_add_func("/net/can/can_test_sleepmode", test_can_sleepmode); |
| |
| return g_test_run(); |
| } |