| /* |
| * QEMU TEWS TPCI200 IndustryPack carrier emulation |
| * |
| * Copyright (C) 2012 Igalia, S.L. |
| * Author: Alberto Garcia <agarcia@igalia.com> |
| * |
| * This code is licensed under the GNU GPL v2 or (at your option) any |
| * later version. |
| */ |
| |
| #include "hw/ipack/ipack.h" |
| #include "hw/pci/pci.h" |
| #include "qemu/bitops.h" |
| #include <stdio.h> |
| |
| /* #define DEBUG_TPCI */ |
| |
| #ifdef DEBUG_TPCI |
| #define DPRINTF(fmt, ...) \ |
| do { fprintf(stderr, "TPCI200: " fmt, ## __VA_ARGS__); } while (0) |
| #else |
| #define DPRINTF(fmt, ...) do { } while (0) |
| #endif |
| |
| #define N_MODULES 4 |
| |
| #define IP_ID_SPACE 2 |
| #define IP_INT_SPACE 3 |
| #define IP_IO_SPACE_ADDR_MASK 0x7F |
| #define IP_ID_SPACE_ADDR_MASK 0x3F |
| #define IP_INT_SPACE_ADDR_MASK 0x3F |
| |
| #define STATUS_INT(IP, INTNO) BIT((IP) * 2 + (INTNO)) |
| #define STATUS_TIME(IP) BIT((IP) + 12) |
| #define STATUS_ERR_ANY 0xF00 |
| |
| #define CTRL_CLKRATE BIT(0) |
| #define CTRL_RECOVER BIT(1) |
| #define CTRL_TIME_INT BIT(2) |
| #define CTRL_ERR_INT BIT(3) |
| #define CTRL_INT_EDGE(INTNO) BIT(4 + (INTNO)) |
| #define CTRL_INT(INTNO) BIT(6 + (INTNO)) |
| |
| #define REG_REV_ID 0x00 |
| #define REG_IP_A_CTRL 0x02 |
| #define REG_IP_B_CTRL 0x04 |
| #define REG_IP_C_CTRL 0x06 |
| #define REG_IP_D_CTRL 0x08 |
| #define REG_RESET 0x0A |
| #define REG_STATUS 0x0C |
| #define IP_N_FROM_REG(REG) ((REG) / 2 - 1) |
| |
| typedef struct { |
| PCIDevice dev; |
| IPackBus bus; |
| MemoryRegion mmio; |
| MemoryRegion io; |
| MemoryRegion las0; |
| MemoryRegion las1; |
| MemoryRegion las2; |
| MemoryRegion las3; |
| bool big_endian[3]; |
| uint8_t ctrl[N_MODULES]; |
| uint16_t status; |
| uint8_t int_set; |
| } TPCI200State; |
| |
| #define TYPE_TPCI200 "tpci200" |
| |
| #define TPCI200(obj) \ |
| OBJECT_CHECK(TPCI200State, (obj), TYPE_TPCI200) |
| |
| static const uint8_t local_config_regs[] = { |
| 0x00, 0xFF, 0xFF, 0x0F, 0x00, 0xFC, 0xFF, 0x0F, 0x00, 0x00, 0x00, |
| 0x0E, 0x00, 0x00, 0x00, 0x0F, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, |
| 0x00, 0x08, 0x01, 0x00, 0x00, 0x04, 0x01, 0x00, 0x00, 0x00, 0x01, |
| 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0xA0, 0x60, 0x41, 0xD4, |
| 0xA2, 0x20, 0x41, 0x14, 0xA2, 0x20, 0x41, 0x14, 0xA2, 0x20, 0x01, |
| 0x14, 0x00, 0x00, 0x00, 0x00, 0x81, 0x00, 0x00, 0x08, 0x01, 0x02, |
| 0x00, 0x04, 0x01, 0x00, 0x00, 0x01, 0x01, 0x00, 0x80, 0x02, 0x41, |
| 0x00, 0x00, 0x00, 0x00, 0x40, 0x7A, 0x00, 0x52, 0x92, 0x24, 0x02 |
| }; |
| |
| static void adjust_addr(bool big_endian, hwaddr *addr, unsigned size) |
| { |
| /* During 8 bit access in big endian mode, |
| odd and even addresses are swapped */ |
| if (big_endian && size == 1) { |
| *addr ^= 1; |
| } |
| } |
| |
| static uint64_t adjust_value(bool big_endian, uint64_t *val, unsigned size) |
| { |
| /* Local spaces only support 8/16 bit access, |
| * so there's no need to care for sizes > 2 */ |
| if (big_endian && size == 2) { |
| *val = bswap16(*val); |
| } |
| return *val; |
| } |
| |
| static void tpci200_set_irq(void *opaque, int intno, int level) |
| { |
| IPackDevice *ip = opaque; |
| IPackBus *bus = IPACK_BUS(qdev_get_parent_bus(DEVICE(ip))); |
| PCIDevice *pcidev = PCI_DEVICE(BUS(bus)->parent); |
| TPCI200State *dev = TPCI200(pcidev); |
| unsigned ip_n = ip->slot; |
| uint16_t prev_status = dev->status; |
| |
| assert(ip->slot >= 0 && ip->slot < N_MODULES); |
| |
| /* The requested interrupt must be enabled in the IP CONTROL |
| * register */ |
| if (!(dev->ctrl[ip_n] & CTRL_INT(intno))) { |
| return; |
| } |
| |
| /* Update the interrupt status in the IP STATUS register */ |
| if (level) { |
| dev->status |= STATUS_INT(ip_n, intno); |
| } else { |
| dev->status &= ~STATUS_INT(ip_n, intno); |
| } |
| |
| /* Return if there are no changes */ |
| if (dev->status == prev_status) { |
| return; |
| } |
| |
| DPRINTF("IP %u INT%u#: %u\n", ip_n, intno, level); |
| |
| /* Check if the interrupt is edge sensitive */ |
| if (dev->ctrl[ip_n] & CTRL_INT_EDGE(intno)) { |
| if (level) { |
| pci_set_irq(&dev->dev, !dev->int_set); |
| pci_set_irq(&dev->dev, dev->int_set); |
| } |
| } else { |
| unsigned i, j; |
| uint16_t level_status = dev->status; |
| |
| /* Check if there are any level sensitive interrupts set by |
| removing the ones that are edge sensitive from the status |
| register */ |
| for (i = 0; i < N_MODULES; i++) { |
| for (j = 0; j < 2; j++) { |
| if (dev->ctrl[i] & CTRL_INT_EDGE(j)) { |
| level_status &= ~STATUS_INT(i, j); |
| } |
| } |
| } |
| |
| if (level_status && !dev->int_set) { |
| pci_irq_assert(&dev->dev); |
| dev->int_set = 1; |
| } else if (!level_status && dev->int_set) { |
| pci_irq_deassert(&dev->dev); |
| dev->int_set = 0; |
| } |
| } |
| } |
| |
| static uint64_t tpci200_read_cfg(void *opaque, hwaddr addr, unsigned size) |
| { |
| TPCI200State *s = opaque; |
| uint8_t ret = 0; |
| if (addr < ARRAY_SIZE(local_config_regs)) { |
| ret = local_config_regs[addr]; |
| } |
| /* Endianness is stored in the first bit of these registers */ |
| if ((addr == 0x2b && s->big_endian[0]) || |
| (addr == 0x2f && s->big_endian[1]) || |
| (addr == 0x33 && s->big_endian[2])) { |
| ret |= 1; |
| } |
| DPRINTF("Read from LCR 0x%x: 0x%x\n", (unsigned) addr, (unsigned) ret); |
| return ret; |
| } |
| |
| static void tpci200_write_cfg(void *opaque, hwaddr addr, uint64_t val, |
| unsigned size) |
| { |
| TPCI200State *s = opaque; |
| /* Endianness is stored in the first bit of these registers */ |
| if (addr == 0x2b || addr == 0x2f || addr == 0x33) { |
| unsigned las = (addr - 0x2b) / 4; |
| s->big_endian[las] = val & 1; |
| DPRINTF("LAS%u big endian mode: %u\n", las, (unsigned) val & 1); |
| } else { |
| DPRINTF("Write to LCR 0x%x: 0x%x\n", (unsigned) addr, (unsigned) val); |
| } |
| } |
| |
| static uint64_t tpci200_read_las0(void *opaque, hwaddr addr, unsigned size) |
| { |
| TPCI200State *s = opaque; |
| uint64_t ret = 0; |
| |
| switch (addr) { |
| |
| case REG_REV_ID: |
| DPRINTF("Read REVISION ID\n"); /* Current value is 0x00 */ |
| break; |
| |
| case REG_IP_A_CTRL: |
| case REG_IP_B_CTRL: |
| case REG_IP_C_CTRL: |
| case REG_IP_D_CTRL: |
| { |
| unsigned ip_n = IP_N_FROM_REG(addr); |
| ret = s->ctrl[ip_n]; |
| DPRINTF("Read IP %c CONTROL: 0x%x\n", 'A' + ip_n, (unsigned) ret); |
| } |
| break; |
| |
| case REG_RESET: |
| DPRINTF("Read RESET\n"); /* Not implemented */ |
| break; |
| |
| case REG_STATUS: |
| ret = s->status; |
| DPRINTF("Read STATUS: 0x%x\n", (unsigned) ret); |
| break; |
| |
| /* Reserved */ |
| default: |
| DPRINTF("Unsupported read from LAS0 0x%x\n", (unsigned) addr); |
| break; |
| } |
| |
| return adjust_value(s->big_endian[0], &ret, size); |
| } |
| |
| static void tpci200_write_las0(void *opaque, hwaddr addr, uint64_t val, |
| unsigned size) |
| { |
| TPCI200State *s = opaque; |
| |
| adjust_value(s->big_endian[0], &val, size); |
| |
| switch (addr) { |
| |
| case REG_REV_ID: |
| DPRINTF("Write Revision ID: 0x%x\n", (unsigned) val); /* No effect */ |
| break; |
| |
| case REG_IP_A_CTRL: |
| case REG_IP_B_CTRL: |
| case REG_IP_C_CTRL: |
| case REG_IP_D_CTRL: |
| { |
| unsigned ip_n = IP_N_FROM_REG(addr); |
| s->ctrl[ip_n] = val; |
| DPRINTF("Write IP %c CONTROL: 0x%x\n", 'A' + ip_n, (unsigned) val); |
| } |
| break; |
| |
| case REG_RESET: |
| DPRINTF("Write RESET: 0x%x\n", (unsigned) val); /* Not implemented */ |
| break; |
| |
| case REG_STATUS: |
| { |
| unsigned i; |
| |
| for (i = 0; i < N_MODULES; i++) { |
| IPackDevice *ip = ipack_device_find(&s->bus, i); |
| |
| if (ip != NULL) { |
| if (val & STATUS_INT(i, 0)) { |
| DPRINTF("Clear IP %c INT0# status\n", 'A' + i); |
| qemu_irq_lower(ip->irq[0]); |
| } |
| if (val & STATUS_INT(i, 1)) { |
| DPRINTF("Clear IP %c INT1# status\n", 'A' + i); |
| qemu_irq_lower(ip->irq[1]); |
| } |
| } |
| |
| if (val & STATUS_TIME(i)) { |
| DPRINTF("Clear IP %c timeout\n", 'A' + i); |
| s->status &= ~STATUS_TIME(i); |
| } |
| } |
| |
| if (val & STATUS_ERR_ANY) { |
| DPRINTF("Unexpected write to STATUS register: 0x%x\n", |
| (unsigned) val); |
| } |
| } |
| break; |
| |
| /* Reserved */ |
| default: |
| DPRINTF("Unsupported write to LAS0 0x%x: 0x%x\n", |
| (unsigned) addr, (unsigned) val); |
| break; |
| } |
| } |
| |
| static uint64_t tpci200_read_las1(void *opaque, hwaddr addr, unsigned size) |
| { |
| TPCI200State *s = opaque; |
| IPackDevice *ip; |
| uint64_t ret = 0; |
| unsigned ip_n, space; |
| uint8_t offset; |
| |
| adjust_addr(s->big_endian[1], &addr, size); |
| |
| /* |
| * The address is divided into the IP module number (0-4), the IP |
| * address space (I/O, ID, INT) and the offset within that space. |
| */ |
| ip_n = addr >> 8; |
| space = (addr >> 6) & 3; |
| ip = ipack_device_find(&s->bus, ip_n); |
| |
| if (ip == NULL) { |
| DPRINTF("Read LAS1: IP module %u not installed\n", ip_n); |
| } else { |
| IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); |
| switch (space) { |
| |
| case IP_ID_SPACE: |
| offset = addr & IP_ID_SPACE_ADDR_MASK; |
| if (k->id_read) { |
| ret = k->id_read(ip, offset); |
| } |
| break; |
| |
| case IP_INT_SPACE: |
| offset = addr & IP_INT_SPACE_ADDR_MASK; |
| |
| /* Read address 0 to ACK IP INT0# and address 2 to ACK IP INT1# */ |
| if (offset == 0 || offset == 2) { |
| unsigned intno = offset / 2; |
| bool int_set = s->status & STATUS_INT(ip_n, intno); |
| bool int_edge_sensitive = s->ctrl[ip_n] & CTRL_INT_EDGE(intno); |
| if (int_set && !int_edge_sensitive) { |
| qemu_irq_lower(ip->irq[intno]); |
| } |
| } |
| |
| if (k->int_read) { |
| ret = k->int_read(ip, offset); |
| } |
| break; |
| |
| default: |
| offset = addr & IP_IO_SPACE_ADDR_MASK; |
| if (k->io_read) { |
| ret = k->io_read(ip, offset); |
| } |
| break; |
| } |
| } |
| |
| return adjust_value(s->big_endian[1], &ret, size); |
| } |
| |
| static void tpci200_write_las1(void *opaque, hwaddr addr, uint64_t val, |
| unsigned size) |
| { |
| TPCI200State *s = opaque; |
| IPackDevice *ip; |
| unsigned ip_n, space; |
| uint8_t offset; |
| |
| adjust_addr(s->big_endian[1], &addr, size); |
| adjust_value(s->big_endian[1], &val, size); |
| |
| /* |
| * The address is divided into the IP module number, the IP |
| * address space (I/O, ID, INT) and the offset within that space. |
| */ |
| ip_n = addr >> 8; |
| space = (addr >> 6) & 3; |
| ip = ipack_device_find(&s->bus, ip_n); |
| |
| if (ip == NULL) { |
| DPRINTF("Write LAS1: IP module %u not installed\n", ip_n); |
| } else { |
| IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); |
| switch (space) { |
| |
| case IP_ID_SPACE: |
| offset = addr & IP_ID_SPACE_ADDR_MASK; |
| if (k->id_write) { |
| k->id_write(ip, offset, val); |
| } |
| break; |
| |
| case IP_INT_SPACE: |
| offset = addr & IP_INT_SPACE_ADDR_MASK; |
| if (k->int_write) { |
| k->int_write(ip, offset, val); |
| } |
| break; |
| |
| default: |
| offset = addr & IP_IO_SPACE_ADDR_MASK; |
| if (k->io_write) { |
| k->io_write(ip, offset, val); |
| } |
| break; |
| } |
| } |
| } |
| |
| static uint64_t tpci200_read_las2(void *opaque, hwaddr addr, unsigned size) |
| { |
| TPCI200State *s = opaque; |
| IPackDevice *ip; |
| uint64_t ret = 0; |
| unsigned ip_n; |
| uint32_t offset; |
| |
| adjust_addr(s->big_endian[2], &addr, size); |
| |
| /* |
| * The address is divided into the IP module number and the offset |
| * within the IP module MEM space. |
| */ |
| ip_n = addr >> 23; |
| offset = addr & 0x7fffff; |
| ip = ipack_device_find(&s->bus, ip_n); |
| |
| if (ip == NULL) { |
| DPRINTF("Read LAS2: IP module %u not installed\n", ip_n); |
| } else { |
| IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); |
| if (k->mem_read16) { |
| ret = k->mem_read16(ip, offset); |
| } |
| } |
| |
| return adjust_value(s->big_endian[2], &ret, size); |
| } |
| |
| static void tpci200_write_las2(void *opaque, hwaddr addr, uint64_t val, |
| unsigned size) |
| { |
| TPCI200State *s = opaque; |
| IPackDevice *ip; |
| unsigned ip_n; |
| uint32_t offset; |
| |
| adjust_addr(s->big_endian[2], &addr, size); |
| adjust_value(s->big_endian[2], &val, size); |
| |
| /* |
| * The address is divided into the IP module number and the offset |
| * within the IP module MEM space. |
| */ |
| ip_n = addr >> 23; |
| offset = addr & 0x7fffff; |
| ip = ipack_device_find(&s->bus, ip_n); |
| |
| if (ip == NULL) { |
| DPRINTF("Write LAS2: IP module %u not installed\n", ip_n); |
| } else { |
| IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); |
| if (k->mem_write16) { |
| k->mem_write16(ip, offset, val); |
| } |
| } |
| } |
| |
| static uint64_t tpci200_read_las3(void *opaque, hwaddr addr, unsigned size) |
| { |
| TPCI200State *s = opaque; |
| IPackDevice *ip; |
| uint64_t ret = 0; |
| /* |
| * The address is divided into the IP module number and the offset |
| * within the IP module MEM space. |
| */ |
| unsigned ip_n = addr >> 22; |
| uint32_t offset = addr & 0x3fffff; |
| |
| ip = ipack_device_find(&s->bus, ip_n); |
| |
| if (ip == NULL) { |
| DPRINTF("Read LAS3: IP module %u not installed\n", ip_n); |
| } else { |
| IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); |
| if (k->mem_read8) { |
| ret = k->mem_read8(ip, offset); |
| } |
| } |
| |
| return ret; |
| } |
| |
| static void tpci200_write_las3(void *opaque, hwaddr addr, uint64_t val, |
| unsigned size) |
| { |
| TPCI200State *s = opaque; |
| IPackDevice *ip; |
| /* |
| * The address is divided into the IP module number and the offset |
| * within the IP module MEM space. |
| */ |
| unsigned ip_n = addr >> 22; |
| uint32_t offset = addr & 0x3fffff; |
| |
| ip = ipack_device_find(&s->bus, ip_n); |
| |
| if (ip == NULL) { |
| DPRINTF("Write LAS3: IP module %u not installed\n", ip_n); |
| } else { |
| IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); |
| if (k->mem_write8) { |
| k->mem_write8(ip, offset, val); |
| } |
| } |
| } |
| |
| static const MemoryRegionOps tpci200_cfg_ops = { |
| .read = tpci200_read_cfg, |
| .write = tpci200_write_cfg, |
| .endianness = DEVICE_NATIVE_ENDIAN, |
| .valid = { |
| .min_access_size = 1, |
| .max_access_size = 4 |
| }, |
| .impl = { |
| .min_access_size = 1, |
| .max_access_size = 1 |
| } |
| }; |
| |
| static const MemoryRegionOps tpci200_las0_ops = { |
| .read = tpci200_read_las0, |
| .write = tpci200_write_las0, |
| .endianness = DEVICE_NATIVE_ENDIAN, |
| .valid = { |
| .min_access_size = 2, |
| .max_access_size = 2 |
| } |
| }; |
| |
| static const MemoryRegionOps tpci200_las1_ops = { |
| .read = tpci200_read_las1, |
| .write = tpci200_write_las1, |
| .endianness = DEVICE_NATIVE_ENDIAN, |
| .valid = { |
| .min_access_size = 1, |
| .max_access_size = 2 |
| } |
| }; |
| |
| static const MemoryRegionOps tpci200_las2_ops = { |
| .read = tpci200_read_las2, |
| .write = tpci200_write_las2, |
| .endianness = DEVICE_NATIVE_ENDIAN, |
| .valid = { |
| .min_access_size = 1, |
| .max_access_size = 2 |
| } |
| }; |
| |
| static const MemoryRegionOps tpci200_las3_ops = { |
| .read = tpci200_read_las3, |
| .write = tpci200_write_las3, |
| .endianness = DEVICE_NATIVE_ENDIAN, |
| .valid = { |
| .min_access_size = 1, |
| .max_access_size = 1 |
| } |
| }; |
| |
| static int tpci200_initfn(PCIDevice *pci_dev) |
| { |
| TPCI200State *s = TPCI200(pci_dev); |
| uint8_t *c = s->dev.config; |
| |
| pci_set_word(c + PCI_COMMAND, 0x0003); |
| pci_set_word(c + PCI_STATUS, 0x0280); |
| |
| pci_set_byte(c + PCI_INTERRUPT_PIN, 0x01); /* Interrupt pin A */ |
| |
| pci_set_byte(c + PCI_CAPABILITY_LIST, 0x40); |
| pci_set_long(c + 0x40, 0x48014801); |
| pci_set_long(c + 0x48, 0x00024C06); |
| pci_set_long(c + 0x4C, 0x00000003); |
| |
| memory_region_init_io(&s->mmio, OBJECT(s), &tpci200_cfg_ops, |
| s, "tpci200_mmio", 128); |
| memory_region_init_io(&s->io, OBJECT(s), &tpci200_cfg_ops, |
| s, "tpci200_io", 128); |
| memory_region_init_io(&s->las0, OBJECT(s), &tpci200_las0_ops, |
| s, "tpci200_las0", 256); |
| memory_region_init_io(&s->las1, OBJECT(s), &tpci200_las1_ops, |
| s, "tpci200_las1", 1024); |
| memory_region_init_io(&s->las2, OBJECT(s), &tpci200_las2_ops, |
| s, "tpci200_las2", 1024*1024*32); |
| memory_region_init_io(&s->las3, OBJECT(s), &tpci200_las3_ops, |
| s, "tpci200_las3", 1024*1024*16); |
| pci_register_bar(&s->dev, 0, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->mmio); |
| pci_register_bar(&s->dev, 1, PCI_BASE_ADDRESS_SPACE_IO, &s->io); |
| pci_register_bar(&s->dev, 2, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las0); |
| pci_register_bar(&s->dev, 3, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las1); |
| pci_register_bar(&s->dev, 4, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las2); |
| pci_register_bar(&s->dev, 5, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las3); |
| |
| ipack_bus_new_inplace(&s->bus, sizeof(s->bus), DEVICE(pci_dev), NULL, |
| N_MODULES, tpci200_set_irq); |
| |
| return 0; |
| } |
| |
| static const VMStateDescription vmstate_tpci200 = { |
| .name = "tpci200", |
| .version_id = 1, |
| .minimum_version_id = 1, |
| .fields = (VMStateField[]) { |
| VMSTATE_PCI_DEVICE(dev, TPCI200State), |
| VMSTATE_BOOL_ARRAY(big_endian, TPCI200State, 3), |
| VMSTATE_UINT8_ARRAY(ctrl, TPCI200State, N_MODULES), |
| VMSTATE_UINT16(status, TPCI200State), |
| VMSTATE_UINT8(int_set, TPCI200State), |
| VMSTATE_END_OF_LIST() |
| } |
| }; |
| |
| static void tpci200_class_init(ObjectClass *klass, void *data) |
| { |
| DeviceClass *dc = DEVICE_CLASS(klass); |
| PCIDeviceClass *k = PCI_DEVICE_CLASS(klass); |
| |
| k->init = tpci200_initfn; |
| k->vendor_id = PCI_VENDOR_ID_TEWS; |
| k->device_id = PCI_DEVICE_ID_TEWS_TPCI200; |
| k->class_id = PCI_CLASS_BRIDGE_OTHER; |
| k->subsystem_vendor_id = PCI_VENDOR_ID_TEWS; |
| k->subsystem_id = 0x300A; |
| set_bit(DEVICE_CATEGORY_INPUT, dc->categories); |
| dc->desc = "TEWS TPCI200 IndustryPack carrier"; |
| dc->vmsd = &vmstate_tpci200; |
| } |
| |
| static const TypeInfo tpci200_info = { |
| .name = TYPE_TPCI200, |
| .parent = TYPE_PCI_DEVICE, |
| .instance_size = sizeof(TPCI200State), |
| .class_init = tpci200_class_init, |
| }; |
| |
| static void tpci200_register_types(void) |
| { |
| type_register_static(&tpci200_info); |
| } |
| |
| type_init(tpci200_register_types) |