| # See docs/tracing.txt for syntax documentation. |
| |
| # hw/misc/eccmemctl.c |
| ecc_mem_writel_mer(uint32_t val) "Write memory enable %08x" |
| ecc_mem_writel_mdr(uint32_t val) "Write memory delay %08x" |
| ecc_mem_writel_mfsr(uint32_t val) "Write memory fault status %08x" |
| ecc_mem_writel_vcr(uint32_t val) "Write slot configuration %08x" |
| ecc_mem_writel_dr(uint32_t val) "Write diagnostic %08x" |
| ecc_mem_writel_ecr0(uint32_t val) "Write event count 1 %08x" |
| ecc_mem_writel_ecr1(uint32_t val) "Write event count 2 %08x" |
| ecc_mem_readl_mer(uint32_t ret) "Read memory enable %08x" |
| ecc_mem_readl_mdr(uint32_t ret) "Read memory delay %08x" |
| ecc_mem_readl_mfsr(uint32_t ret) "Read memory fault status %08x" |
| ecc_mem_readl_vcr(uint32_t ret) "Read slot configuration %08x" |
| ecc_mem_readl_mfar0(uint32_t ret) "Read memory fault address 0 %08x" |
| ecc_mem_readl_mfar1(uint32_t ret) "Read memory fault address 1 %08x" |
| ecc_mem_readl_dr(uint32_t ret) "Read diagnostic %08x" |
| ecc_mem_readl_ecr0(uint32_t ret) "Read event count 1 %08x" |
| ecc_mem_readl_ecr1(uint32_t ret) "Read event count 2 %08x" |
| ecc_diag_mem_writeb(uint64_t addr, uint32_t val) "Write diagnostic %"PRId64" = %02x" |
| ecc_diag_mem_readb(uint64_t addr, uint32_t ret) "Read diagnostic %"PRId64"= %02x" |
| |
| # hw/misc/slavio_misc.c |
| slavio_misc_update_irq_raise(void) "Raise IRQ" |
| slavio_misc_update_irq_lower(void) "Lower IRQ" |
| slavio_set_power_fail(int power_failing, uint8_t config) "Power fail: %d, config: %d" |
| slavio_cfg_mem_writeb(uint32_t val) "Write config %02x" |
| slavio_cfg_mem_readb(uint32_t ret) "Read config %02x" |
| slavio_diag_mem_writeb(uint32_t val) "Write diag %02x" |
| slavio_diag_mem_readb(uint32_t ret) "Read diag %02x" |
| slavio_mdm_mem_writeb(uint32_t val) "Write modem control %02x" |
| slavio_mdm_mem_readb(uint32_t ret) "Read modem control %02x" |
| slavio_aux1_mem_writeb(uint32_t val) "Write aux1 %02x" |
| slavio_aux1_mem_readb(uint32_t ret) "Read aux1 %02x" |
| slavio_aux2_mem_writeb(uint32_t val) "Write aux2 %02x" |
| slavio_aux2_mem_readb(uint32_t ret) "Read aux2 %02x" |
| apc_mem_writeb(uint32_t val) "Write power management %02x" |
| apc_mem_readb(uint32_t ret) "Read power management %02x" |
| slavio_sysctrl_mem_writel(uint32_t val) "Write system control %08x" |
| slavio_sysctrl_mem_readl(uint32_t ret) "Read system control %08x" |
| slavio_led_mem_writew(uint32_t val) "Write diagnostic LED %04x" |
| slavio_led_mem_readw(uint32_t ret) "Read diagnostic LED %04x" |
| |
| # hw/misc/milkymist-hpdmc.c |
| milkymist_hpdmc_memory_read(uint32_t addr, uint32_t value) "addr=%08x value=%08x" |
| milkymist_hpdmc_memory_write(uint32_t addr, uint32_t value) "addr=%08x value=%08x" |
| |
| # hw/misc/milkymist-pfpu.c |
| milkymist_pfpu_memory_read(uint32_t addr, uint32_t value) "addr %08x value %08x" |
| milkymist_pfpu_memory_write(uint32_t addr, uint32_t value) "addr %08x value %08x" |
| milkymist_pfpu_vectout(uint32_t a, uint32_t b, uint32_t dma_ptr) "a %08x b %08x dma_ptr %08x" |
| milkymist_pfpu_pulse_irq(void) "Pulse IRQ" |
| |
| # hw/misc/aspeed_scu.c |
| aspeed_scu_write(uint64_t offset, unsigned size, uint32_t data) "To 0x%" PRIx64 " of size %u: 0x%" PRIx32 |
| |
| # hw/misc/mps2_scc.c |
| mps2_scc_read(uint64_t offset, uint64_t data, unsigned size) "MPS2 SCC read: offset 0x%" PRIx64 " data 0x%" PRIx64 " size %u" |
| mps2_scc_write(uint64_t offset, uint64_t data, unsigned size) "MPS2 SCC write: offset 0x%" PRIx64 " data 0x%" PRIx64 " size %u" |
| mps2_scc_reset(void) "MPS2 SCC: reset" |
| mps2_scc_leds(char led7, char led6, char led5, char led4, char led3, char led2, char led1, char led0) "MPS2 SCC LEDs: %c%c%c%c%c%c%c%c" |
| mps2_scc_cfg_write(unsigned function, unsigned device, uint32_t value) "MPS2 SCC config write: function %d device %d data 0x%" PRIx32 |
| mps2_scc_cfg_read(unsigned function, unsigned device, uint32_t value) "MPS2 SCC config read: function %d device %d data 0x%" PRIx32 |
