| /* |
| * CFI parallel flash with Intel command set emulation |
| * |
| * Copyright (c) 2006 Thorsten Zitterell |
| * Copyright (c) 2005 Jocelyn Mayer |
| * |
| * This library is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU Lesser General Public |
| * License as published by the Free Software Foundation; either |
| * version 2 of the License, or (at your option) any later version. |
| * |
| * This library is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * Lesser General Public License for more details. |
| * |
| * You should have received a copy of the GNU Lesser General Public |
| * License along with this library; if not, see <http://www.gnu.org/licenses/>. |
| */ |
| |
| /* |
| * For now, this code can emulate flashes of 1, 2 or 4 bytes width. |
| * Supported commands/modes are: |
| * - flash read |
| * - flash write |
| * - flash ID read |
| * - sector erase |
| * - CFI queries |
| * |
| * It does not support timings |
| * It does not support flash interleaving |
| * It does not implement software data protection as found in many real chips |
| * It does not implement erase suspend/resume commands |
| * It does not implement multiple sectors erase |
| * |
| * It does not implement much more ... |
| */ |
| |
| #include "qemu/osdep.h" |
| #include "hw/block/block.h" |
| #include "hw/block/flash.h" |
| #include "hw/qdev-properties.h" |
| #include "sysemu/block-backend.h" |
| #include "qapi/error.h" |
| #include "qemu/timer.h" |
| #include "qemu/bitops.h" |
| #include "qemu/error-report.h" |
| #include "qemu/host-utils.h" |
| #include "qemu/log.h" |
| #include "qemu/module.h" |
| #include "qemu/option.h" |
| #include "hw/sysbus.h" |
| #include "migration/vmstate.h" |
| #include "sysemu/blockdev.h" |
| #include "sysemu/runstate.h" |
| #include "trace.h" |
| |
| /* #define PFLASH_DEBUG */ |
| #ifdef PFLASH_DEBUG |
| #define DPRINTF(fmt, ...) \ |
| do { \ |
| fprintf(stderr, "PFLASH: " fmt , ## __VA_ARGS__); \ |
| } while (0) |
| #else |
| #define DPRINTF(fmt, ...) do { } while (0) |
| #endif |
| |
| #define PFLASH_BE 0 |
| #define PFLASH_SECURE 1 |
| |
| struct PFlashCFI01 { |
| /*< private >*/ |
| SysBusDevice parent_obj; |
| /*< public >*/ |
| |
| BlockBackend *blk; |
| uint32_t nb_blocs; |
| uint64_t sector_len; |
| uint8_t bank_width; |
| uint8_t device_width; /* If 0, device width not specified. */ |
| uint8_t max_device_width; /* max device width in bytes */ |
| uint32_t features; |
| uint8_t wcycle; /* if 0, the flash is read normally */ |
| int ro; |
| uint8_t cmd; |
| uint8_t status; |
| uint16_t ident0; |
| uint16_t ident1; |
| uint16_t ident2; |
| uint16_t ident3; |
| uint8_t cfi_table[0x52]; |
| uint64_t counter; |
| unsigned int writeblock_size; |
| QEMUTimer *timer; |
| MemoryRegion mem; |
| char *name; |
| void *storage; |
| VMChangeStateEntry *vmstate; |
| bool old_multiple_chip_handling; |
| }; |
| |
| static int pflash_post_load(void *opaque, int version_id); |
| |
| static const VMStateDescription vmstate_pflash = { |
| .name = "pflash_cfi01", |
| .version_id = 1, |
| .minimum_version_id = 1, |
| .post_load = pflash_post_load, |
| .fields = (VMStateField[]) { |
| VMSTATE_UINT8(wcycle, PFlashCFI01), |
| VMSTATE_UINT8(cmd, PFlashCFI01), |
| VMSTATE_UINT8(status, PFlashCFI01), |
| VMSTATE_UINT64(counter, PFlashCFI01), |
| VMSTATE_END_OF_LIST() |
| } |
| }; |
| |
| static void pflash_timer (void *opaque) |
| { |
| PFlashCFI01 *pfl = opaque; |
| |
| trace_pflash_timer_expired(pfl->cmd); |
| /* Reset flash */ |
| pfl->status ^= 0x80; |
| memory_region_rom_device_set_romd(&pfl->mem, true); |
| pfl->wcycle = 0; |
| pfl->cmd = 0; |
| } |
| |
| /* Perform a CFI query based on the bank width of the flash. |
| * If this code is called we know we have a device_width set for |
| * this flash. |
| */ |
| static uint32_t pflash_cfi_query(PFlashCFI01 *pfl, hwaddr offset) |
| { |
| int i; |
| uint32_t resp = 0; |
| hwaddr boff; |
| |
| /* Adjust incoming offset to match expected device-width |
| * addressing. CFI query addresses are always specified in terms of |
| * the maximum supported width of the device. This means that x8 |
| * devices and x8/x16 devices in x8 mode behave differently. For |
| * devices that are not used at their max width, we will be |
| * provided with addresses that use higher address bits than |
| * expected (based on the max width), so we will shift them lower |
| * so that they will match the addresses used when |
| * device_width==max_device_width. |
| */ |
| boff = offset >> (ctz32(pfl->bank_width) + |
| ctz32(pfl->max_device_width) - ctz32(pfl->device_width)); |
| |
| if (boff >= sizeof(pfl->cfi_table)) { |
| return 0; |
| } |
| /* Now we will construct the CFI response generated by a single |
| * device, then replicate that for all devices that make up the |
| * bus. For wide parts used in x8 mode, CFI query responses |
| * are different than native byte-wide parts. |
| */ |
| resp = pfl->cfi_table[boff]; |
| if (pfl->device_width != pfl->max_device_width) { |
| /* The only case currently supported is x8 mode for a |
| * wider part. |
| */ |
| if (pfl->device_width != 1 || pfl->bank_width > 4) { |
| DPRINTF("%s: Unsupported device configuration: " |
| "device_width=%d, max_device_width=%d\n", |
| __func__, pfl->device_width, |
| pfl->max_device_width); |
| return 0; |
| } |
| /* CFI query data is repeated, rather than zero padded for |
| * wide devices used in x8 mode. |
| */ |
| for (i = 1; i < pfl->max_device_width; i++) { |
| resp = deposit32(resp, 8 * i, 8, pfl->cfi_table[boff]); |
| } |
| } |
| /* Replicate responses for each device in bank. */ |
| if (pfl->device_width < pfl->bank_width) { |
| for (i = pfl->device_width; |
| i < pfl->bank_width; i += pfl->device_width) { |
| resp = deposit32(resp, 8 * i, 8 * pfl->device_width, resp); |
| } |
| } |
| |
| return resp; |
| } |
| |
| |
| |
| /* Perform a device id query based on the bank width of the flash. */ |
| static uint32_t pflash_devid_query(PFlashCFI01 *pfl, hwaddr offset) |
| { |
| int i; |
| uint32_t resp; |
| hwaddr boff; |
| |
| /* Adjust incoming offset to match expected device-width |
| * addressing. Device ID read addresses are always specified in |
| * terms of the maximum supported width of the device. This means |
| * that x8 devices and x8/x16 devices in x8 mode behave |
| * differently. For devices that are not used at their max width, |
| * we will be provided with addresses that use higher address bits |
| * than expected (based on the max width), so we will shift them |
| * lower so that they will match the addresses used when |
| * device_width==max_device_width. |
| */ |
| boff = offset >> (ctz32(pfl->bank_width) + |
| ctz32(pfl->max_device_width) - ctz32(pfl->device_width)); |
| |
| /* Mask off upper bits which may be used in to query block |
| * or sector lock status at other addresses. |
| * Offsets 2/3 are block lock status, is not emulated. |
| */ |
| switch (boff & 0xFF) { |
| case 0: |
| resp = pfl->ident0; |
| trace_pflash_manufacturer_id(resp); |
| break; |
| case 1: |
| resp = pfl->ident1; |
| trace_pflash_device_id(resp); |
| break; |
| default: |
| trace_pflash_device_info(offset); |
| return 0; |
| break; |
| } |
| /* Replicate responses for each device in bank. */ |
| if (pfl->device_width < pfl->bank_width) { |
| for (i = pfl->device_width; |
| i < pfl->bank_width; i += pfl->device_width) { |
| resp = deposit32(resp, 8 * i, 8 * pfl->device_width, resp); |
| } |
| } |
| |
| return resp; |
| } |
| |
| static uint32_t pflash_data_read(PFlashCFI01 *pfl, hwaddr offset, |
| int width, int be) |
| { |
| uint8_t *p; |
| uint32_t ret; |
| |
| p = pfl->storage; |
| switch (width) { |
| case 1: |
| ret = p[offset]; |
| break; |
| case 2: |
| if (be) { |
| ret = p[offset] << 8; |
| ret |= p[offset + 1]; |
| } else { |
| ret = p[offset]; |
| ret |= p[offset + 1] << 8; |
| } |
| break; |
| case 4: |
| if (be) { |
| ret = p[offset] << 24; |
| ret |= p[offset + 1] << 16; |
| ret |= p[offset + 2] << 8; |
| ret |= p[offset + 3]; |
| } else { |
| ret = p[offset]; |
| ret |= p[offset + 1] << 8; |
| ret |= p[offset + 2] << 16; |
| ret |= p[offset + 3] << 24; |
| } |
| break; |
| default: |
| DPRINTF("BUG in %s\n", __func__); |
| abort(); |
| } |
| trace_pflash_data_read(offset, width, ret); |
| return ret; |
| } |
| |
| static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr offset, |
| int width, int be) |
| { |
| hwaddr boff; |
| uint32_t ret; |
| |
| ret = -1; |
| switch (pfl->cmd) { |
| default: |
| /* This should never happen : reset state & treat it as a read */ |
| DPRINTF("%s: unknown command state: %x\n", __func__, pfl->cmd); |
| pfl->wcycle = 0; |
| pfl->cmd = 0; |
| /* fall through to read code */ |
| case 0x00: |
| /* Flash area read */ |
| ret = pflash_data_read(pfl, offset, width, be); |
| break; |
| case 0x10: /* Single byte program */ |
| case 0x20: /* Block erase */ |
| case 0x28: /* Block erase */ |
| case 0x40: /* single byte program */ |
| case 0x50: /* Clear status register */ |
| case 0x60: /* Block /un)lock */ |
| case 0x70: /* Status Register */ |
| case 0xe8: /* Write block */ |
| /* Status register read. Return status from each device in |
| * bank. |
| */ |
| ret = pfl->status; |
| if (pfl->device_width && width > pfl->device_width) { |
| int shift = pfl->device_width * 8; |
| while (shift + pfl->device_width * 8 <= width * 8) { |
| ret |= pfl->status << shift; |
| shift += pfl->device_width * 8; |
| } |
| } else if (!pfl->device_width && width > 2) { |
| /* Handle 32 bit flash cases where device width is not |
| * set. (Existing behavior before device width added.) |
| */ |
| ret |= pfl->status << 16; |
| } |
| DPRINTF("%s: status %x\n", __func__, ret); |
| break; |
| case 0x90: |
| if (!pfl->device_width) { |
| /* Preserve old behavior if device width not specified */ |
| boff = offset & 0xFF; |
| if (pfl->bank_width == 2) { |
| boff = boff >> 1; |
| } else if (pfl->bank_width == 4) { |
| boff = boff >> 2; |
| } |
| |
| switch (boff) { |
| case 0: |
| ret = pfl->ident0 << 8 | pfl->ident1; |
| trace_pflash_manufacturer_id(ret); |
| break; |
| case 1: |
| ret = pfl->ident2 << 8 | pfl->ident3; |
| trace_pflash_device_id(ret); |
| break; |
| default: |
| trace_pflash_device_info(boff); |
| ret = 0; |
| break; |
| } |
| } else { |
| /* If we have a read larger than the bank_width, combine multiple |
| * manufacturer/device ID queries into a single response. |
| */ |
| int i; |
| for (i = 0; i < width; i += pfl->bank_width) { |
| ret = deposit32(ret, i * 8, pfl->bank_width * 8, |
| pflash_devid_query(pfl, |
| offset + i * pfl->bank_width)); |
| } |
| } |
| break; |
| case 0x98: /* Query mode */ |
| if (!pfl->device_width) { |
| /* Preserve old behavior if device width not specified */ |
| boff = offset & 0xFF; |
| if (pfl->bank_width == 2) { |
| boff = boff >> 1; |
| } else if (pfl->bank_width == 4) { |
| boff = boff >> 2; |
| } |
| |
| if (boff < sizeof(pfl->cfi_table)) { |
| ret = pfl->cfi_table[boff]; |
| } else { |
| ret = 0; |
| } |
| } else { |
| /* If we have a read larger than the bank_width, combine multiple |
| * CFI queries into a single response. |
| */ |
| int i; |
| for (i = 0; i < width; i += pfl->bank_width) { |
| ret = deposit32(ret, i * 8, pfl->bank_width * 8, |
| pflash_cfi_query(pfl, |
| offset + i * pfl->bank_width)); |
| } |
| } |
| |
| break; |
| } |
| trace_pflash_io_read(offset, width, ret, pfl->cmd, pfl->wcycle); |
| |
| return ret; |
| } |
| |
| /* update flash content on disk */ |
| static void pflash_update(PFlashCFI01 *pfl, int offset, |
| int size) |
| { |
| int offset_end; |
| if (pfl->blk) { |
| offset_end = offset + size; |
| /* widen to sector boundaries */ |
| offset = QEMU_ALIGN_DOWN(offset, BDRV_SECTOR_SIZE); |
| offset_end = QEMU_ALIGN_UP(offset_end, BDRV_SECTOR_SIZE); |
| blk_pwrite(pfl->blk, offset, pfl->storage + offset, |
| offset_end - offset, 0); |
| } |
| } |
| |
| static inline void pflash_data_write(PFlashCFI01 *pfl, hwaddr offset, |
| uint32_t value, int width, int be) |
| { |
| uint8_t *p = pfl->storage; |
| |
| trace_pflash_data_write(offset, width, value, pfl->counter); |
| switch (width) { |
| case 1: |
| p[offset] = value; |
| break; |
| case 2: |
| if (be) { |
| p[offset] = value >> 8; |
| p[offset + 1] = value; |
| } else { |
| p[offset] = value; |
| p[offset + 1] = value >> 8; |
| } |
| break; |
| case 4: |
| if (be) { |
| p[offset] = value >> 24; |
| p[offset + 1] = value >> 16; |
| p[offset + 2] = value >> 8; |
| p[offset + 3] = value; |
| } else { |
| p[offset] = value; |
| p[offset + 1] = value >> 8; |
| p[offset + 2] = value >> 16; |
| p[offset + 3] = value >> 24; |
| } |
| break; |
| } |
| |
| } |
| |
| static void pflash_write(PFlashCFI01 *pfl, hwaddr offset, |
| uint32_t value, int width, int be) |
| { |
| uint8_t *p; |
| uint8_t cmd; |
| |
| cmd = value; |
| |
| trace_pflash_io_write(offset, width, value, pfl->wcycle); |
| if (!pfl->wcycle) { |
| /* Set the device in I/O access mode */ |
| memory_region_rom_device_set_romd(&pfl->mem, false); |
| } |
| |
| switch (pfl->wcycle) { |
| case 0: |
| /* read mode */ |
| switch (cmd) { |
| case 0x00: /* ??? */ |
| goto reset_flash; |
| case 0x10: /* Single Byte Program */ |
| case 0x40: /* Single Byte Program */ |
| DPRINTF("%s: Single Byte Program\n", __func__); |
| break; |
| case 0x20: /* Block erase */ |
| p = pfl->storage; |
| offset &= ~(pfl->sector_len - 1); |
| |
| DPRINTF("%s: block erase at " TARGET_FMT_plx " bytes %x\n", |
| __func__, offset, (unsigned)pfl->sector_len); |
| |
| if (!pfl->ro) { |
| memset(p + offset, 0xff, pfl->sector_len); |
| pflash_update(pfl, offset, pfl->sector_len); |
| } else { |
| pfl->status |= 0x20; /* Block erase error */ |
| } |
| pfl->status |= 0x80; /* Ready! */ |
| break; |
| case 0x50: /* Clear status bits */ |
| DPRINTF("%s: Clear status bits\n", __func__); |
| pfl->status = 0x0; |
| goto reset_flash; |
| case 0x60: /* Block (un)lock */ |
| DPRINTF("%s: Block unlock\n", __func__); |
| break; |
| case 0x70: /* Status Register */ |
| DPRINTF("%s: Read status register\n", __func__); |
| pfl->cmd = cmd; |
| return; |
| case 0x90: /* Read Device ID */ |
| DPRINTF("%s: Read Device information\n", __func__); |
| pfl->cmd = cmd; |
| return; |
| case 0x98: /* CFI query */ |
| DPRINTF("%s: CFI query\n", __func__); |
| break; |
| case 0xe8: /* Write to buffer */ |
| DPRINTF("%s: Write to buffer\n", __func__); |
| /* FIXME should save @offset, @width for case 1+ */ |
| qemu_log_mask(LOG_UNIMP, |
| "%s: Write to buffer emulation is flawed\n", |
| __func__); |
| pfl->status |= 0x80; /* Ready! */ |
| break; |
| case 0xf0: /* Probe for AMD flash */ |
| DPRINTF("%s: Probe for AMD flash\n", __func__); |
| goto reset_flash; |
| case 0xff: /* Read array mode */ |
| DPRINTF("%s: Read array mode\n", __func__); |
| goto reset_flash; |
| default: |
| goto error_flash; |
| } |
| pfl->wcycle++; |
| pfl->cmd = cmd; |
| break; |
| case 1: |
| switch (pfl->cmd) { |
| case 0x10: /* Single Byte Program */ |
| case 0x40: /* Single Byte Program */ |
| DPRINTF("%s: Single Byte Program\n", __func__); |
| if (!pfl->ro) { |
| pflash_data_write(pfl, offset, value, width, be); |
| pflash_update(pfl, offset, width); |
| } else { |
| pfl->status |= 0x10; /* Programming error */ |
| } |
| pfl->status |= 0x80; /* Ready! */ |
| pfl->wcycle = 0; |
| break; |
| case 0x20: /* Block erase */ |
| case 0x28: |
| if (cmd == 0xd0) { /* confirm */ |
| pfl->wcycle = 0; |
| pfl->status |= 0x80; |
| } else if (cmd == 0xff) { /* read array mode */ |
| goto reset_flash; |
| } else |
| goto error_flash; |
| |
| break; |
| case 0xe8: |
| /* Mask writeblock size based on device width, or bank width if |
| * device width not specified. |
| */ |
| /* FIXME check @offset, @width */ |
| if (pfl->device_width) { |
| value = extract32(value, 0, pfl->device_width * 8); |
| } else { |
| value = extract32(value, 0, pfl->bank_width * 8); |
| } |
| DPRINTF("%s: block write of %x bytes\n", __func__, value); |
| pfl->counter = value; |
| pfl->wcycle++; |
| break; |
| case 0x60: |
| if (cmd == 0xd0) { |
| pfl->wcycle = 0; |
| pfl->status |= 0x80; |
| } else if (cmd == 0x01) { |
| pfl->wcycle = 0; |
| pfl->status |= 0x80; |
| } else if (cmd == 0xff) { |
| goto reset_flash; |
| } else { |
| DPRINTF("%s: Unknown (un)locking command\n", __func__); |
| goto reset_flash; |
| } |
| break; |
| case 0x98: |
| if (cmd == 0xff) { |
| goto reset_flash; |
| } else { |
| DPRINTF("%s: leaving query mode\n", __func__); |
| } |
| break; |
| default: |
| goto error_flash; |
| } |
| break; |
| case 2: |
| switch (pfl->cmd) { |
| case 0xe8: /* Block write */ |
| /* FIXME check @offset, @width */ |
| if (!pfl->ro) { |
| /* |
| * FIXME writing straight to memory is *wrong*. We |
| * should write to a buffer, and flush it to memory |
| * only on confirm command (see below). |
| */ |
| pflash_data_write(pfl, offset, value, width, be); |
| } else { |
| pfl->status |= 0x10; /* Programming error */ |
| } |
| |
| pfl->status |= 0x80; |
| |
| if (!pfl->counter) { |
| hwaddr mask = pfl->writeblock_size - 1; |
| mask = ~mask; |
| |
| DPRINTF("%s: block write finished\n", __func__); |
| pfl->wcycle++; |
| if (!pfl->ro) { |
| /* Flush the entire write buffer onto backing storage. */ |
| /* FIXME premature! */ |
| pflash_update(pfl, offset & mask, pfl->writeblock_size); |
| } else { |
| pfl->status |= 0x10; /* Programming error */ |
| } |
| } |
| |
| pfl->counter--; |
| break; |
| default: |
| goto error_flash; |
| } |
| break; |
| case 3: /* Confirm mode */ |
| switch (pfl->cmd) { |
| case 0xe8: /* Block write */ |
| if (cmd == 0xd0) { |
| /* FIXME this is where we should write out the buffer */ |
| pfl->wcycle = 0; |
| pfl->status |= 0x80; |
| } else { |
| qemu_log_mask(LOG_UNIMP, |
| "%s: Aborting write to buffer not implemented," |
| " the data is already written to storage!\n" |
| "Flash device reset into READ mode.\n", |
| __func__); |
| goto reset_flash; |
| } |
| break; |
| default: |
| goto error_flash; |
| } |
| break; |
| default: |
| /* Should never happen */ |
| DPRINTF("%s: invalid write state\n", __func__); |
| goto reset_flash; |
| } |
| return; |
| |
| error_flash: |
| qemu_log_mask(LOG_UNIMP, "%s: Unimplemented flash cmd sequence " |
| "(offset " TARGET_FMT_plx ", wcycle 0x%x cmd 0x%x value 0x%x)" |
| "\n", __func__, offset, pfl->wcycle, pfl->cmd, value); |
| |
| reset_flash: |
| trace_pflash_reset(); |
| memory_region_rom_device_set_romd(&pfl->mem, true); |
| pfl->wcycle = 0; |
| pfl->cmd = 0; |
| } |
| |
| |
| static MemTxResult pflash_mem_read_with_attrs(void *opaque, hwaddr addr, uint64_t *value, |
| unsigned len, MemTxAttrs attrs) |
| { |
| PFlashCFI01 *pfl = opaque; |
| bool be = !!(pfl->features & (1 << PFLASH_BE)); |
| |
| if ((pfl->features & (1 << PFLASH_SECURE)) && !attrs.secure) { |
| *value = pflash_data_read(opaque, addr, len, be); |
| } else { |
| *value = pflash_read(opaque, addr, len, be); |
| } |
| return MEMTX_OK; |
| } |
| |
| static MemTxResult pflash_mem_write_with_attrs(void *opaque, hwaddr addr, uint64_t value, |
| unsigned len, MemTxAttrs attrs) |
| { |
| PFlashCFI01 *pfl = opaque; |
| bool be = !!(pfl->features & (1 << PFLASH_BE)); |
| |
| if ((pfl->features & (1 << PFLASH_SECURE)) && !attrs.secure) { |
| return MEMTX_ERROR; |
| } else { |
| pflash_write(opaque, addr, value, len, be); |
| return MEMTX_OK; |
| } |
| } |
| |
| static const MemoryRegionOps pflash_cfi01_ops = { |
| .read_with_attrs = pflash_mem_read_with_attrs, |
| .write_with_attrs = pflash_mem_write_with_attrs, |
| .endianness = DEVICE_NATIVE_ENDIAN, |
| }; |
| |
| static void pflash_cfi01_realize(DeviceState *dev, Error **errp) |
| { |
| PFlashCFI01 *pfl = PFLASH_CFI01(dev); |
| uint64_t total_len; |
| int ret; |
| uint64_t blocks_per_device, sector_len_per_device, device_len; |
| int num_devices; |
| Error *local_err = NULL; |
| |
| if (pfl->sector_len == 0) { |
| error_setg(errp, "attribute \"sector-length\" not specified or zero."); |
| return; |
| } |
| if (pfl->nb_blocs == 0) { |
| error_setg(errp, "attribute \"num-blocks\" not specified or zero."); |
| return; |
| } |
| if (pfl->name == NULL) { |
| error_setg(errp, "attribute \"name\" not specified."); |
| return; |
| } |
| |
| total_len = pfl->sector_len * pfl->nb_blocs; |
| |
| /* These are only used to expose the parameters of each device |
| * in the cfi_table[]. |
| */ |
| num_devices = pfl->device_width ? (pfl->bank_width / pfl->device_width) : 1; |
| if (pfl->old_multiple_chip_handling) { |
| blocks_per_device = pfl->nb_blocs / num_devices; |
| sector_len_per_device = pfl->sector_len; |
| } else { |
| blocks_per_device = pfl->nb_blocs; |
| sector_len_per_device = pfl->sector_len / num_devices; |
| } |
| device_len = sector_len_per_device * blocks_per_device; |
| |
| memory_region_init_rom_device( |
| &pfl->mem, OBJECT(dev), |
| &pflash_cfi01_ops, |
| pfl, |
| pfl->name, total_len, &local_err); |
| if (local_err) { |
| error_propagate(errp, local_err); |
| return; |
| } |
| |
| pfl->storage = memory_region_get_ram_ptr(&pfl->mem); |
| sysbus_init_mmio(SYS_BUS_DEVICE(dev), &pfl->mem); |
| |
| if (pfl->blk) { |
| uint64_t perm; |
| pfl->ro = blk_is_read_only(pfl->blk); |
| perm = BLK_PERM_CONSISTENT_READ | (pfl->ro ? 0 : BLK_PERM_WRITE); |
| ret = blk_set_perm(pfl->blk, perm, BLK_PERM_ALL, errp); |
| if (ret < 0) { |
| return; |
| } |
| } else { |
| pfl->ro = 0; |
| } |
| |
| if (pfl->blk) { |
| if (!blk_check_size_and_read_all(pfl->blk, pfl->storage, total_len, |
| errp)) { |
| vmstate_unregister_ram(&pfl->mem, DEVICE(pfl)); |
| return; |
| } |
| } |
| |
| /* Default to devices being used at their maximum device width. This was |
| * assumed before the device_width support was added. |
| */ |
| if (!pfl->max_device_width) { |
| pfl->max_device_width = pfl->device_width; |
| } |
| |
| pfl->timer = timer_new_ns(QEMU_CLOCK_VIRTUAL, pflash_timer, pfl); |
| pfl->wcycle = 0; |
| pfl->cmd = 0; |
| pfl->status = 0x80; /* WSM ready */ |
| /* Hardcoded CFI table */ |
| /* Standard "QRY" string */ |
| pfl->cfi_table[0x10] = 'Q'; |
| pfl->cfi_table[0x11] = 'R'; |
| pfl->cfi_table[0x12] = 'Y'; |
| /* Command set (Intel) */ |
| pfl->cfi_table[0x13] = 0x01; |
| pfl->cfi_table[0x14] = 0x00; |
| /* Primary extended table address (none) */ |
| pfl->cfi_table[0x15] = 0x31; |
| pfl->cfi_table[0x16] = 0x00; |
| /* Alternate command set (none) */ |
| pfl->cfi_table[0x17] = 0x00; |
| pfl->cfi_table[0x18] = 0x00; |
| /* Alternate extended table (none) */ |
| pfl->cfi_table[0x19] = 0x00; |
| pfl->cfi_table[0x1A] = 0x00; |
| /* Vcc min */ |
| pfl->cfi_table[0x1B] = 0x45; |
| /* Vcc max */ |
| pfl->cfi_table[0x1C] = 0x55; |
| /* Vpp min (no Vpp pin) */ |
| pfl->cfi_table[0x1D] = 0x00; |
| /* Vpp max (no Vpp pin) */ |
| pfl->cfi_table[0x1E] = 0x00; |
| /* Reserved */ |
| pfl->cfi_table[0x1F] = 0x07; |
| /* Timeout for min size buffer write */ |
| pfl->cfi_table[0x20] = 0x07; |
| /* Typical timeout for block erase */ |
| pfl->cfi_table[0x21] = 0x0a; |
| /* Typical timeout for full chip erase (4096 ms) */ |
| pfl->cfi_table[0x22] = 0x00; |
| /* Reserved */ |
| pfl->cfi_table[0x23] = 0x04; |
| /* Max timeout for buffer write */ |
| pfl->cfi_table[0x24] = 0x04; |
| /* Max timeout for block erase */ |
| pfl->cfi_table[0x25] = 0x04; |
| /* Max timeout for chip erase */ |
| pfl->cfi_table[0x26] = 0x00; |
| /* Device size */ |
| pfl->cfi_table[0x27] = ctz32(device_len); /* + 1; */ |
| /* Flash device interface (8 & 16 bits) */ |
| pfl->cfi_table[0x28] = 0x02; |
| pfl->cfi_table[0x29] = 0x00; |
| /* Max number of bytes in multi-bytes write */ |
| if (pfl->bank_width == 1) { |
| pfl->cfi_table[0x2A] = 0x08; |
| } else { |
| pfl->cfi_table[0x2A] = 0x0B; |
| } |
| pfl->writeblock_size = 1 << pfl->cfi_table[0x2A]; |
| if (!pfl->old_multiple_chip_handling && num_devices > 1) { |
| pfl->writeblock_size *= num_devices; |
| } |
| |
| pfl->cfi_table[0x2B] = 0x00; |
| /* Number of erase block regions (uniform) */ |
| pfl->cfi_table[0x2C] = 0x01; |
| /* Erase block region 1 */ |
| pfl->cfi_table[0x2D] = blocks_per_device - 1; |
| pfl->cfi_table[0x2E] = (blocks_per_device - 1) >> 8; |
| pfl->cfi_table[0x2F] = sector_len_per_device >> 8; |
| pfl->cfi_table[0x30] = sector_len_per_device >> 16; |
| |
| /* Extended */ |
| pfl->cfi_table[0x31] = 'P'; |
| pfl->cfi_table[0x32] = 'R'; |
| pfl->cfi_table[0x33] = 'I'; |
| |
| pfl->cfi_table[0x34] = '1'; |
| pfl->cfi_table[0x35] = '0'; |
| |
| pfl->cfi_table[0x36] = 0x00; |
| pfl->cfi_table[0x37] = 0x00; |
| pfl->cfi_table[0x38] = 0x00; |
| pfl->cfi_table[0x39] = 0x00; |
| |
| pfl->cfi_table[0x3a] = 0x00; |
| |
| pfl->cfi_table[0x3b] = 0x00; |
| pfl->cfi_table[0x3c] = 0x00; |
| |
| pfl->cfi_table[0x3f] = 0x01; /* Number of protection fields */ |
| } |
| |
| static void pflash_cfi01_system_reset(DeviceState *dev) |
| { |
| PFlashCFI01 *pfl = PFLASH_CFI01(dev); |
| |
| /* |
| * The command 0x00 is not assigned by the CFI open standard, |
| * but QEMU historically uses it for the READ_ARRAY command (0xff). |
| */ |
| pfl->cmd = 0x00; |
| pfl->wcycle = 0; |
| memory_region_rom_device_set_romd(&pfl->mem, true); |
| /* |
| * The WSM ready timer occurs at most 150ns after system reset. |
| * This model deliberately ignores this delay. |
| */ |
| pfl->status = 0x80; |
| } |
| |
| static Property pflash_cfi01_properties[] = { |
| DEFINE_PROP_DRIVE("drive", PFlashCFI01, blk), |
| /* num-blocks is the number of blocks actually visible to the guest, |
| * ie the total size of the device divided by the sector length. |
| * If we're emulating flash devices wired in parallel the actual |
| * number of blocks per indvidual device will differ. |
| */ |
| DEFINE_PROP_UINT32("num-blocks", PFlashCFI01, nb_blocs, 0), |
| DEFINE_PROP_UINT64("sector-length", PFlashCFI01, sector_len, 0), |
| /* width here is the overall width of this QEMU device in bytes. |
| * The QEMU device may be emulating a number of flash devices |
| * wired up in parallel; the width of each individual flash |
| * device should be specified via device-width. If the individual |
| * devices have a maximum width which is greater than the width |
| * they are being used for, this maximum width should be set via |
| * max-device-width (which otherwise defaults to device-width). |
| * So for instance a 32-bit wide QEMU flash device made from four |
| * 16-bit flash devices used in 8-bit wide mode would be configured |
| * with width = 4, device-width = 1, max-device-width = 2. |
| * |
| * If device-width is not specified we default to backwards |
| * compatible behaviour which is a bad emulation of two |
| * 16 bit devices making up a 32 bit wide QEMU device. This |
| * is deprecated for new uses of this device. |
| */ |
| DEFINE_PROP_UINT8("width", PFlashCFI01, bank_width, 0), |
| DEFINE_PROP_UINT8("device-width", PFlashCFI01, device_width, 0), |
| DEFINE_PROP_UINT8("max-device-width", PFlashCFI01, max_device_width, 0), |
| DEFINE_PROP_BIT("big-endian", PFlashCFI01, features, PFLASH_BE, 0), |
| DEFINE_PROP_BIT("secure", PFlashCFI01, features, PFLASH_SECURE, 0), |
| DEFINE_PROP_UINT16("id0", PFlashCFI01, ident0, 0), |
| DEFINE_PROP_UINT16("id1", PFlashCFI01, ident1, 0), |
| DEFINE_PROP_UINT16("id2", PFlashCFI01, ident2, 0), |
| DEFINE_PROP_UINT16("id3", PFlashCFI01, ident3, 0), |
| DEFINE_PROP_STRING("name", PFlashCFI01, name), |
| DEFINE_PROP_BOOL("old-multiple-chip-handling", PFlashCFI01, |
| old_multiple_chip_handling, false), |
| DEFINE_PROP_END_OF_LIST(), |
| }; |
| |
| static void pflash_cfi01_class_init(ObjectClass *klass, void *data) |
| { |
| DeviceClass *dc = DEVICE_CLASS(klass); |
| |
| dc->reset = pflash_cfi01_system_reset; |
| dc->realize = pflash_cfi01_realize; |
| dc->props = pflash_cfi01_properties; |
| dc->vmsd = &vmstate_pflash; |
| set_bit(DEVICE_CATEGORY_STORAGE, dc->categories); |
| } |
| |
| |
| static const TypeInfo pflash_cfi01_info = { |
| .name = TYPE_PFLASH_CFI01, |
| .parent = TYPE_SYS_BUS_DEVICE, |
| .instance_size = sizeof(PFlashCFI01), |
| .class_init = pflash_cfi01_class_init, |
| }; |
| |
| static void pflash_cfi01_register_types(void) |
| { |
| type_register_static(&pflash_cfi01_info); |
| } |
| |
| type_init(pflash_cfi01_register_types) |
| |
| PFlashCFI01 *pflash_cfi01_register(hwaddr base, |
| const char *name, |
| hwaddr size, |
| BlockBackend *blk, |
| uint32_t sector_len, |
| int bank_width, |
| uint16_t id0, uint16_t id1, |
| uint16_t id2, uint16_t id3, |
| int be) |
| { |
| DeviceState *dev = qdev_create(NULL, TYPE_PFLASH_CFI01); |
| |
| if (blk) { |
| qdev_prop_set_drive(dev, "drive", blk, &error_abort); |
| } |
| assert(size % sector_len == 0); |
| qdev_prop_set_uint32(dev, "num-blocks", size / sector_len); |
| qdev_prop_set_uint64(dev, "sector-length", sector_len); |
| qdev_prop_set_uint8(dev, "width", bank_width); |
| qdev_prop_set_bit(dev, "big-endian", !!be); |
| qdev_prop_set_uint16(dev, "id0", id0); |
| qdev_prop_set_uint16(dev, "id1", id1); |
| qdev_prop_set_uint16(dev, "id2", id2); |
| qdev_prop_set_uint16(dev, "id3", id3); |
| qdev_prop_set_string(dev, "name", name); |
| qdev_init_nofail(dev); |
| |
| sysbus_mmio_map(SYS_BUS_DEVICE(dev), 0, base); |
| return PFLASH_CFI01(dev); |
| } |
| |
| BlockBackend *pflash_cfi01_get_blk(PFlashCFI01 *fl) |
| { |
| return fl->blk; |
| } |
| |
| MemoryRegion *pflash_cfi01_get_memory(PFlashCFI01 *fl) |
| { |
| return &fl->mem; |
| } |
| |
| /* |
| * Handle -drive if=pflash for machines that use properties. |
| * If @dinfo is null, do nothing. |
| * Else if @fl's property "drive" is already set, fatal error. |
| * Else set it to the BlockBackend with @dinfo. |
| */ |
| void pflash_cfi01_legacy_drive(PFlashCFI01 *fl, DriveInfo *dinfo) |
| { |
| Location loc; |
| |
| if (!dinfo) { |
| return; |
| } |
| |
| loc_push_none(&loc); |
| qemu_opts_loc_restore(dinfo->opts); |
| if (fl->blk) { |
| error_report("clashes with -machine"); |
| exit(1); |
| } |
| qdev_prop_set_drive(DEVICE(fl), "drive", |
| blk_by_legacy_dinfo(dinfo), &error_fatal); |
| loc_pop(&loc); |
| } |
| |
| static void postload_update_cb(void *opaque, int running, RunState state) |
| { |
| PFlashCFI01 *pfl = opaque; |
| |
| /* This is called after bdrv_invalidate_cache_all. */ |
| qemu_del_vm_change_state_handler(pfl->vmstate); |
| pfl->vmstate = NULL; |
| |
| DPRINTF("%s: updating bdrv for %s\n", __func__, pfl->name); |
| pflash_update(pfl, 0, pfl->sector_len * pfl->nb_blocs); |
| } |
| |
| static int pflash_post_load(void *opaque, int version_id) |
| { |
| PFlashCFI01 *pfl = opaque; |
| |
| if (!pfl->ro) { |
| pfl->vmstate = qemu_add_vm_change_state_handler(postload_update_cb, |
| pfl); |
| } |
| return 0; |
| } |
