docs/throttle.txt - qemu - Git at Google

 The QEMU throttling infrastructure
 ==================================
 Copyright (C) 2016 Igalia, S.L.
 Author: Alberto Garcia <berto@igalia.com>

 This work is licensed under the terms of the GNU GPL, version 2 or
 later. See the COPYING file in the top-level directory.

 Introduction
 ------------
 QEMU includes a throttling module that can be used to set limits to
 I/O operations. The code itself is generic and independent of the I/O
 units, but it is currently used to limit the number of bytes per second
 and operations per second (IOPS) when performing disk I/O.

 This document explains how to use the throttling code in QEMU, and how
 it works internally. The implementation is in throttle.c.


 Using throttling to limit disk I/O
 ----------------------------------
 Two aspects of the disk I/O can be limited: the number of bytes per
 second and the number of operations per second (IOPS). For each one of
 them the user can set a global limit or separate limits for read and
 write operations. This gives us a total of six different parameters.

 I/O limits can be set using the throttling.* parameters of -drive, or
 using the QMP 'block_set_io_throttle' command. These are the names of
 the parameters for both cases:

 |-----------------------+-----------------------|
 | -drive                | block_set_io_throttle |
 |-----------------------+-----------------------|
 | throttling.iops-total | iops                  |
 | throttling.iops-read  | iops_rd               |
 | throttling.iops-write | iops_wr               |
 | throttling.bps-total  | bps                   |
 | throttling.bps-read   | bps_rd                |
 | throttling.bps-write  | bps_wr                |
 |-----------------------+-----------------------|

 It is possible to set limits for both IOPS and bps at the same time,
 and for each case we can decide whether to have separate read and
 write limits or not, but note that if iops-total is set then neither
 iops-read nor iops-write can be set. The same applies to bps-total and
 bps-read/write.

 The default value of these parameters is 0, and it means 'unlimited'.

 In its most basic usage, the user can add a drive to QEMU with a limit
 of 100 IOPS with the following -drive line:

    -drive file=hd0.qcow2,throttling.iops-total=100

 We can do the same using QMP. In this case all these parameters are
 mandatory, so we must set to 0 the ones that we don't want to limit:

    { "execute": "block_set_io_throttle",
      "arguments": {
         "device": "virtio0",
         "iops": 100,
         "iops_rd": 0,
         "iops_wr": 0,
         "bps": 0,
         "bps_rd": 0,
         "bps_wr": 0
      }
    }


 I/O bursts
 ----------
 In addition to the basic limits we have just seen, QEMU allows the
 user to do bursts of I/O for a configurable amount of time. A burst is
 an amount of I/O that can exceed the basic limit. Bursts are useful to
 allow better performance when there are peaks of activity (the OS
 boots, a service needs to be restarted) while keeping the average
 limits lower the rest of the time.

 Two parameters control bursts: their length and the maximum amount of
 I/O they allow. These two can be configured separately for each one of
 the six basic parameters described in the previous section, but in
 this section we'll use 'iops-total' as an example.

 The I/O limit during bursts is set using 'iops-total-max', and the
 maximum length (in seconds) is set with 'iops-total-max-length'. So if
 we want to configure a drive with a basic limit of 100 IOPS and allow
 bursts of 2000 IOPS for 60 seconds, we would do it like this (the line
 is split for clarity):

    -drive file=hd0.qcow2,
           throttling.iops-total=100,
           throttling.iops-total-max=2000,
           throttling.iops-total-max-length=60

 Or, with QMP:

    { "execute": "block_set_io_throttle",
      "arguments": {
         "device": "virtio0",
         "iops": 100,
         "iops_rd": 0,
         "iops_wr": 0,
         "bps": 0,
         "bps_rd": 0,
         "bps_wr": 0,
         "iops_max": 2000,
         "iops_max_length": 60,
      }
    }

 With this, the user can perform I/O on hd0.qcow2 at a rate of 2000
 IOPS for 1 minute before it's throttled down to 100 IOPS.

 The user will be able to do bursts again if there's a sufficiently
 long period of time with unused I/O (see below for details).

 The default value for 'iops-total-max' is 0 and it means that bursts
 are not allowed. 'iops-total-max-length' can only be set if
 'iops-total-max' is set as well, and its default value is 1 second.

 Here's the complete list of parameters for configuring bursts:

 |----------------------------------+-----------------------|
 | -drive                           | block_set_io_throttle |
 |----------------------------------+-----------------------|
 | throttling.iops-total-max        | iops_max              |
 | throttling.iops-total-max-length | iops_max_length       |
 | throttling.iops-read-max         | iops_rd_max           |
 | throttling.iops-read-max-length  | iops_rd_max_length    |
 | throttling.iops-write-max        | iops_wr_max           |
 | throttling.iops-write-max-length | iops_wr_max_length    |
 | throttling.bps-total-max         | bps_max               |
 | throttling.bps-total-max-length  | bps_max_length        |
 | throttling.bps-read-max          | bps_rd_max            |
 | throttling.bps-read-max-length   | bps_rd_max_length     |
 | throttling.bps-write-max         | bps_wr_max            |
 | throttling.bps-write-max-length  | bps_wr_max_length     |
 |----------------------------------+-----------------------|


 Controlling the size of I/O operations
 --------------------------------------
 When applying IOPS limits all I/O operations are treated equally
 regardless of their size. This means that the user can take advantage
 of this in order to circumvent the limits and submit one huge I/O
 request instead of several smaller ones.

 QEMU provides a setting called throttling.iops-size to prevent this
 from happening. This setting specifies the size (in bytes) of an I/O
 request for accounting purposes. Larger requests will be counted
 proportionally to this size.

 For example, if iops-size is set to 4096 then an 8KB request will be
 counted as two, and a 6KB request will be counted as one and a
 half. This only applies to requests larger than iops-size: smaller
 requests will be always counted as one, no matter their size.

 The default value of iops-size is 0 and it means that the size of the
 requests is never taken into account when applying IOPS limits.


 Applying I/O limits to groups of disks
 --------------------------------------
 In all the examples so far we have seen how to apply limits to the I/O
 performed on individual drives, but QEMU allows grouping drives so
 they all share the same limits.

 The way it works is that each drive with I/O limits is assigned to a
 group named using the throttling.group parameter. If this parameter is
 not specified, then the device name (i.e. 'virtio0', 'ide0-hd0') will
 be used as the group name.

 Limits set using the throttling.* parameters discussed earlier in this
 document apply to the combined I/O of all members of a group.

 Consider this example:

    -drive file=hd1.qcow2,throttling.iops-total=6000,throttling.group=foo
    -drive file=hd2.qcow2,throttling.iops-total=6000,throttling.group=foo
    -drive file=hd3.qcow2,throttling.iops-total=3000,throttling.group=bar
    -drive file=hd4.qcow2,throttling.iops-total=6000,throttling.group=foo
    -drive file=hd5.qcow2,throttling.iops-total=3000,throttling.group=bar
    -drive file=hd6.qcow2,throttling.iops-total=5000

 Here hd1, hd2 and hd4 are all members of a group named 'foo' with a
 combined IOPS limit of 6000, and hd3 and hd5 are members of 'bar'. hd6
 is left alone (technically it is part of a 1-member group).

 Limits are applied in a round-robin fashion so if there are concurrent
 I/O requests on several drives of the same group they will be
 distributed evenly.

 When I/O limits are applied to an existing drive using the QMP command
 'block_set_io_throttle', the following things need to be taken into
 account:

    - I/O limits are shared within the same group, so new values will
      affect all members and overwrite the previous settings. In other
      words: if different limits are applied to members of the same
      group, the last one wins.

    - If 'group' is unset it is assumed to be the current group of that
      drive. If the drive is not in a group yet, it will be added to a
      group named after the device name.

    - If 'group' is set then the drive will be moved to that group if
      it was member of a different one. In this case the limits
      specified in the parameters will be applied to the new group
      only.

    - I/O limits can be disabled by setting all of them to 0. In this
      case the device will be removed from its group and the rest of
      its members will not be affected. The 'group' parameter is
      ignored.


 The Leaky Bucket algorithm
 --------------------------
 I/O limits in QEMU are implemented using the leaky bucket algorithm
 (specifically the "Leaky bucket as a meter" variant).

 This algorithm uses the analogy of a bucket that leaks water
 constantly. The water that gets into the bucket represents the I/O
 that has been performed, and no more I/O is allowed once the bucket is
 full.

 To see the way this corresponds to the throttling parameters in QEMU,
 consider the following values:

   iops-total=100
   iops-total-max=2000
   iops-total-max-length=60

   - Water leaks from the bucket at a rate of 100 IOPS.
   - Water can be added to the bucket at a rate of 2000 IOPS.
   - The size of the bucket is 2000 x 60 = 120000
   - If 'iops-total-max-length' is unset then it defaults to 1 and the
     size of the bucket is 2000.
   - If 'iops-total-max' is unset then 'iops-total-max-length' must be
     unset as well. In this case the bucket size is 100.

 The bucket is initially empty, therefore water can be added until it's
 full at a rate of 2000 IOPS (the burst rate). Once the bucket is full
 we can only add as much water as it leaks, therefore the I/O rate is
 reduced to 100 IOPS. If we add less water than it leaks then the
 bucket will start to empty, allowing for bursts again.

 Note that since water is leaking from the bucket even during bursts,
 it will take a bit more than 60 seconds at 2000 IOPS to fill it
 up. After those 60 seconds the bucket will have leaked 60 x 100 =
 6000, allowing for 3 more seconds of I/O at 2000 IOPS.

 Also, due to the way the algorithm works, longer burst can be done at
 a lower I/O rate, e.g. 1000 IOPS during 120 seconds.
	The QEMU throttling infrastructure
	==================================
	Copyright (C) 2016 Igalia, S.L.
	Author: Alberto Garcia <berto@igalia.com>

	This work is licensed under the terms of the GNU GPL, version 2 or
	later. See the COPYING file in the top-level directory.

	Introduction
	------------
	QEMU includes a throttling module that can be used to set limits to
	I/O operations. The code itself is generic and independent of the I/O
	units, but it is currently used to limit the number of bytes per second
	and operations per second (IOPS) when performing disk I/O.

	This document explains how to use the throttling code in QEMU, and how
	it works internally. The implementation is in throttle.c.


	Using throttling to limit disk I/O
	----------------------------------
	Two aspects of the disk I/O can be limited: the number of bytes per
	second and the number of operations per second (IOPS). For each one of
	them the user can set a global limit or separate limits for read and
	write operations. This gives us a total of six different parameters.

	I/O limits can be set using the throttling.* parameters of -drive, or
	using the QMP 'block_set_io_throttle' command. These are the names of
	the parameters for both cases:

	\|-----------------------+-----------------------\|
	\| -drive \| block_set_io_throttle \|
	\|-----------------------+-----------------------\|
	\| throttling.iops-total \| iops \|
	\| throttling.iops-read \| iops_rd \|
	\| throttling.iops-write \| iops_wr \|
	\| throttling.bps-total \| bps \|
	\| throttling.bps-read \| bps_rd \|
	\| throttling.bps-write \| bps_wr \|
	\|-----------------------+-----------------------\|

	It is possible to set limits for both IOPS and bps at the same time,
	and for each case we can decide whether to have separate read and
	write limits or not, but note that if iops-total is set then neither
	iops-read nor iops-write can be set. The same applies to bps-total and
	bps-read/write.

	The default value of these parameters is 0, and it means 'unlimited'.

	In its most basic usage, the user can add a drive to QEMU with a limit
	of 100 IOPS with the following -drive line:

	-drive file=hd0.qcow2,throttling.iops-total=100

	We can do the same using QMP. In this case all these parameters are
	mandatory, so we must set to 0 the ones that we don't want to limit:

	{ "execute": "block_set_io_throttle",
	"arguments": {
	"device": "virtio0",
	"iops": 100,
	"iops_rd": 0,
	"iops_wr": 0,
	"bps": 0,
	"bps_rd": 0,
	"bps_wr": 0
	}
	}


	I/O bursts
	----------
	In addition to the basic limits we have just seen, QEMU allows the
	user to do bursts of I/O for a configurable amount of time. A burst is
	an amount of I/O that can exceed the basic limit. Bursts are useful to
	allow better performance when there are peaks of activity (the OS
	boots, a service needs to be restarted) while keeping the average
	limits lower the rest of the time.

	Two parameters control bursts: their length and the maximum amount of
	I/O they allow. These two can be configured separately for each one of
	the six basic parameters described in the previous section, but in
	this section we'll use 'iops-total' as an example.

	The I/O limit during bursts is set using 'iops-total-max', and the
	maximum length (in seconds) is set with 'iops-total-max-length'. So if
	we want to configure a drive with a basic limit of 100 IOPS and allow
	bursts of 2000 IOPS for 60 seconds, we would do it like this (the line
	is split for clarity):

	-drive file=hd0.qcow2,
	throttling.iops-total=100,
	throttling.iops-total-max=2000,
	throttling.iops-total-max-length=60

	Or, with QMP:

	{ "execute": "block_set_io_throttle",
	"arguments": {
	"device": "virtio0",
	"iops": 100,
	"iops_rd": 0,
	"iops_wr": 0,
	"bps": 0,
	"bps_rd": 0,
	"bps_wr": 0,
	"iops_max": 2000,
	"iops_max_length": 60,
	}
	}

	With this, the user can perform I/O on hd0.qcow2 at a rate of 2000
	IOPS for 1 minute before it's throttled down to 100 IOPS.

	The user will be able to do bursts again if there's a sufficiently
	long period of time with unused I/O (see below for details).

	The default value for 'iops-total-max' is 0 and it means that bursts
	are not allowed. 'iops-total-max-length' can only be set if
	'iops-total-max' is set as well, and its default value is 1 second.

	Here's the complete list of parameters for configuring bursts:

	\|----------------------------------+-----------------------\|
	\| -drive \| block_set_io_throttle \|
	\|----------------------------------+-----------------------\|
	\| throttling.iops-total-max \| iops_max \|
	\| throttling.iops-total-max-length \| iops_max_length \|
	\| throttling.iops-read-max \| iops_rd_max \|
	\| throttling.iops-read-max-length \| iops_rd_max_length \|
	\| throttling.iops-write-max \| iops_wr_max \|
	\| throttling.iops-write-max-length \| iops_wr_max_length \|
	\| throttling.bps-total-max \| bps_max \|
	\| throttling.bps-total-max-length \| bps_max_length \|
	\| throttling.bps-read-max \| bps_rd_max \|
	\| throttling.bps-read-max-length \| bps_rd_max_length \|
	\| throttling.bps-write-max \| bps_wr_max \|
	\| throttling.bps-write-max-length \| bps_wr_max_length \|
	\|----------------------------------+-----------------------\|


	Controlling the size of I/O operations
	--------------------------------------
	When applying IOPS limits all I/O operations are treated equally
	regardless of their size. This means that the user can take advantage
	of this in order to circumvent the limits and submit one huge I/O
	request instead of several smaller ones.

	QEMU provides a setting called throttling.iops-size to prevent this
	from happening. This setting specifies the size (in bytes) of an I/O
	request for accounting purposes. Larger requests will be counted
	proportionally to this size.

	For example, if iops-size is set to 4096 then an 8KB request will be
	counted as two, and a 6KB request will be counted as one and a
	half. This only applies to requests larger than iops-size: smaller
	requests will be always counted as one, no matter their size.

	The default value of iops-size is 0 and it means that the size of the
	requests is never taken into account when applying IOPS limits.


	Applying I/O limits to groups of disks
	--------------------------------------
	In all the examples so far we have seen how to apply limits to the I/O
	performed on individual drives, but QEMU allows grouping drives so
	they all share the same limits.

	The way it works is that each drive with I/O limits is assigned to a
	group named using the throttling.group parameter. If this parameter is
	not specified, then the device name (i.e. 'virtio0', 'ide0-hd0') will
	be used as the group name.

	Limits set using the throttling.* parameters discussed earlier in this
	document apply to the combined I/O of all members of a group.

	Consider this example:

	-drive file=hd1.qcow2,throttling.iops-total=6000,throttling.group=foo
	-drive file=hd2.qcow2,throttling.iops-total=6000,throttling.group=foo
	-drive file=hd3.qcow2,throttling.iops-total=3000,throttling.group=bar
	-drive file=hd4.qcow2,throttling.iops-total=6000,throttling.group=foo
	-drive file=hd5.qcow2,throttling.iops-total=3000,throttling.group=bar
	-drive file=hd6.qcow2,throttling.iops-total=5000

	Here hd1, hd2 and hd4 are all members of a group named 'foo' with a
	combined IOPS limit of 6000, and hd3 and hd5 are members of 'bar'. hd6
	is left alone (technically it is part of a 1-member group).

	Limits are applied in a round-robin fashion so if there are concurrent
	I/O requests on several drives of the same group they will be
	distributed evenly.

	When I/O limits are applied to an existing drive using the QMP command
	'block_set_io_throttle', the following things need to be taken into
	account:

	- I/O limits are shared within the same group, so new values will
	affect all members and overwrite the previous settings. In other
	words: if different limits are applied to members of the same
	group, the last one wins.

	- If 'group' is unset it is assumed to be the current group of that
	drive. If the drive is not in a group yet, it will be added to a
	group named after the device name.

	- If 'group' is set then the drive will be moved to that group if
	it was member of a different one. In this case the limits
	specified in the parameters will be applied to the new group
	only.

	- I/O limits can be disabled by setting all of them to 0. In this
	case the device will be removed from its group and the rest of
	its members will not be affected. The 'group' parameter is
	ignored.


	The Leaky Bucket algorithm
	--------------------------
	I/O limits in QEMU are implemented using the leaky bucket algorithm
	(specifically the "Leaky bucket as a meter" variant).

	This algorithm uses the analogy of a bucket that leaks water
	constantly. The water that gets into the bucket represents the I/O
	that has been performed, and no more I/O is allowed once the bucket is
	full.

	To see the way this corresponds to the throttling parameters in QEMU,
	consider the following values:

	iops-total=100
	iops-total-max=2000
	iops-total-max-length=60

	- Water leaks from the bucket at a rate of 100 IOPS.
	- Water can be added to the bucket at a rate of 2000 IOPS.
	- The size of the bucket is 2000 x 60 = 120000
	- If 'iops-total-max-length' is unset then it defaults to 1 and the
	size of the bucket is 2000.
	- If 'iops-total-max' is unset then 'iops-total-max-length' must be
	unset as well. In this case the bucket size is 100.

	The bucket is initially empty, therefore water can be added until it's
	full at a rate of 2000 IOPS (the burst rate). Once the bucket is full
	we can only add as much water as it leaks, therefore the I/O rate is
	reduced to 100 IOPS. If we add less water than it leaks then the
	bucket will start to empty, allowing for bursts again.

	Note that since water is leaking from the bucket even during bursts,
	it will take a bit more than 60 seconds at 2000 IOPS to fill it
	up. After those 60 seconds the bucket will have leaked 60 x 100 =
	6000, allowing for 3 more seconds of I/O at 2000 IOPS.

	Also, due to the way the algorithm works, longer burst can be done at
	a lower I/O rate, e.g. 1000 IOPS during 120 seconds.