| /* |
| * QEMU aCube Sam460ex board emulation |
| * |
| * Copyright (c) 2012 François Revol |
| * Copyright (c) 2016-2018 BALATON Zoltan |
| * |
| * This file is derived from hw/ppc440_bamboo.c, |
| * the copyright for that material belongs to the original owners. |
| * |
| * This work is licensed under the GNU GPL license version 2 or later. |
| * |
| */ |
| |
| #include "qemu/osdep.h" |
| #include "qemu/units.h" |
| #include "qemu-common.h" |
| #include "qemu/error-report.h" |
| #include "qapi/error.h" |
| #include "hw/hw.h" |
| #include "hw/boards.h" |
| #include "sysemu/kvm.h" |
| #include "kvm_ppc.h" |
| #include "sysemu/device_tree.h" |
| #include "sysemu/block-backend.h" |
| #include "hw/loader.h" |
| #include "elf.h" |
| #include "exec/address-spaces.h" |
| #include "exec/memory.h" |
| #include "ppc440.h" |
| #include "ppc405.h" |
| #include "hw/block/flash.h" |
| #include "sysemu/sysemu.h" |
| #include "sysemu/qtest.h" |
| #include "hw/sysbus.h" |
| #include "hw/char/serial.h" |
| #include "hw/i2c/ppc4xx_i2c.h" |
| #include "hw/i2c/smbus.h" |
| #include "hw/usb/hcd-ehci.h" |
| #include "hw/ppc/fdt.h" |
| |
| #include <libfdt.h> |
| |
| #define BINARY_DEVICE_TREE_FILE "canyonlands.dtb" |
| #define UBOOT_FILENAME "u-boot-sam460-20100605.bin" |
| /* to extract the official U-Boot bin from the updater: */ |
| /* dd bs=1 skip=$(($(stat -c '%s' updater/updater-460) - 0x80000)) \ |
| if=updater/updater-460 of=u-boot-sam460-20100605.bin */ |
| |
| /* from Sam460 U-Boot include/configs/Sam460ex.h */ |
| #define FLASH_BASE 0xfff00000 |
| #define FLASH_BASE_H 0x4 |
| #define FLASH_SIZE (1 * MiB) |
| #define UBOOT_LOAD_BASE 0xfff80000 |
| #define UBOOT_SIZE 0x00080000 |
| #define UBOOT_ENTRY 0xfffffffc |
| |
| /* from U-Boot */ |
| #define EPAPR_MAGIC (0x45504150) |
| #define KERNEL_ADDR 0x1000000 |
| #define FDT_ADDR 0x1800000 |
| #define RAMDISK_ADDR 0x1900000 |
| |
| /* Sam460ex IRQ MAP: |
| IRQ0 = ETH_INT |
| IRQ1 = FPGA_INT |
| IRQ2 = PCI_INT (PCIA, PCIB, PCIC, PCIB) |
| IRQ3 = FPGA_INT2 |
| IRQ11 = RTC_INT |
| IRQ12 = SM502_INT |
| */ |
| |
| #define CPU_FREQ 1150000000 |
| #define PLB_FREQ 230000000 |
| #define OPB_FREQ 115000000 |
| #define EBC_FREQ 115000000 |
| #define UART_FREQ 11059200 |
| #define SDRAM_NR_BANKS 4 |
| |
| /* FIXME: See u-boot.git 8ac41e, also fix in ppc440_uc.c */ |
| static const unsigned int ppc460ex_sdram_bank_sizes[] = { |
| 1 * GiB, 512 * MiB, 256 * MiB, 128 * MiB, 64 * MiB, 32 * MiB, 0 |
| }; |
| |
| struct boot_info { |
| uint32_t dt_base; |
| uint32_t dt_size; |
| uint32_t entry; |
| }; |
| |
| /*****************************************************************************/ |
| /* SPD eeprom content from mips_malta.c */ |
| |
| struct _eeprom24c0x_t { |
| uint8_t tick; |
| uint8_t address; |
| uint8_t command; |
| uint8_t ack; |
| uint8_t scl; |
| uint8_t sda; |
| uint8_t data; |
| uint8_t contents[256]; |
| }; |
| |
| typedef struct _eeprom24c0x_t eeprom24c0x_t; |
| |
| static eeprom24c0x_t spd_eeprom = { |
| .contents = { |
| /* 00000000: */ 0x80, 0x08, 0xFF, 0x0D, 0x0A, 0xFF, 0x40, 0x00, |
| /* 00000008: */ 0x04, 0x75, 0x54, 0x00, 0x82, 0x08, 0x00, 0x01, |
| /* 00000010: */ 0x8F, 0x04, 0x02, 0x01, 0x01, 0x00, 0x00, 0x00, |
| /* 00000018: */ 0x00, 0x00, 0x00, 0x14, 0x0F, 0x14, 0x2D, 0xFF, |
| /* 00000020: */ 0x15, 0x08, 0x15, 0x08, 0x00, 0x00, 0x00, 0x00, |
| /* 00000028: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000030: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000038: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x12, 0xD0, |
| /* 00000040: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000048: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000050: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000058: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000060: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000068: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000070: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| /* 00000078: */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x64, 0xF4, |
| }, |
| }; |
| |
| static void generate_eeprom_spd(uint8_t *eeprom, ram_addr_t ram_size) |
| { |
| enum { SDR = 0x4, DDR1 = 0x7, DDR2 = 0x8 } type; |
| uint8_t *spd = spd_eeprom.contents; |
| uint8_t nbanks = 0; |
| uint16_t density = 0; |
| int i; |
| |
| /* work in terms of MB */ |
| ram_size /= MiB; |
| |
| while ((ram_size >= 4) && (nbanks <= 2)) { |
| int sz_log2 = MIN(31 - clz32(ram_size), 14); |
| nbanks++; |
| density |= 1 << (sz_log2 - 2); |
| ram_size -= 1 << sz_log2; |
| } |
| |
| /* split to 2 banks if possible */ |
| if ((nbanks == 1) && (density > 1)) { |
| nbanks++; |
| density >>= 1; |
| } |
| |
| if (density & 0xff00) { |
| density = (density & 0xe0) | ((density >> 8) & 0x1f); |
| type = DDR2; |
| } else if (!(density & 0x1f)) { |
| type = DDR2; |
| } else { |
| type = SDR; |
| } |
| |
| if (ram_size) { |
| warn_report("SPD cannot represent final " RAM_ADDR_FMT "MB" |
| " of SDRAM", ram_size); |
| } |
| |
| /* fill in SPD memory information */ |
| spd[2] = type; |
| spd[5] = nbanks; |
| spd[31] = density; |
| |
| /* XXX: this is totally random */ |
| spd[9] = 0x10; /* CAS tcyc */ |
| spd[18] = 0x20; /* CAS bit */ |
| spd[23] = 0x10; /* CAS tcyc */ |
| spd[25] = 0x10; /* CAS tcyc */ |
| |
| /* checksum */ |
| spd[63] = 0; |
| for (i = 0; i < 63; i++) { |
| spd[63] += spd[i]; |
| } |
| |
| /* copy for SMBUS */ |
| memcpy(eeprom, spd, sizeof(spd_eeprom.contents)); |
| } |
| |
| static void generate_eeprom_serial(uint8_t *eeprom) |
| { |
| int i, pos = 0; |
| uint8_t mac[6] = { 0x00 }; |
| uint8_t sn[5] = { 0x01, 0x23, 0x45, 0x67, 0x89 }; |
| |
| /* version */ |
| eeprom[pos++] = 0x01; |
| |
| /* count */ |
| eeprom[pos++] = 0x02; |
| |
| /* MAC address */ |
| eeprom[pos++] = 0x01; /* MAC */ |
| eeprom[pos++] = 0x06; /* length */ |
| memcpy(&eeprom[pos], mac, sizeof(mac)); |
| pos += sizeof(mac); |
| |
| /* serial number */ |
| eeprom[pos++] = 0x02; /* serial */ |
| eeprom[pos++] = 0x05; /* length */ |
| memcpy(&eeprom[pos], sn, sizeof(sn)); |
| pos += sizeof(sn); |
| |
| /* checksum */ |
| eeprom[pos] = 0; |
| for (i = 0; i < pos; i++) { |
| eeprom[pos] += eeprom[i]; |
| } |
| } |
| |
| /*****************************************************************************/ |
| |
| static int sam460ex_load_uboot(void) |
| { |
| DriveInfo *dinfo; |
| BlockBackend *blk = NULL; |
| hwaddr base = FLASH_BASE | ((hwaddr)FLASH_BASE_H << 32); |
| long bios_size = FLASH_SIZE; |
| int fl_sectors; |
| |
| dinfo = drive_get(IF_PFLASH, 0, 0); |
| if (dinfo) { |
| blk = blk_by_legacy_dinfo(dinfo); |
| bios_size = blk_getlength(blk); |
| } |
| fl_sectors = (bios_size + 65535) >> 16; |
| |
| if (!pflash_cfi01_register(base, NULL, "sam460ex.flash", bios_size, |
| blk, 64 * KiB, fl_sectors, |
| 1, 0x89, 0x18, 0x0000, 0x0, 1)) { |
| error_report("qemu: Error registering flash memory."); |
| /* XXX: return an error instead? */ |
| exit(1); |
| } |
| |
| if (!blk) { |
| /*error_report("No flash image given with the 'pflash' parameter," |
| " using default u-boot image");*/ |
| base = UBOOT_LOAD_BASE | ((hwaddr)FLASH_BASE_H << 32); |
| rom_add_file_fixed(UBOOT_FILENAME, base, -1); |
| } |
| |
| return 0; |
| } |
| |
| static int sam460ex_load_device_tree(hwaddr addr, |
| uint32_t ramsize, |
| hwaddr initrd_base, |
| hwaddr initrd_size, |
| const char *kernel_cmdline) |
| { |
| uint32_t mem_reg_property[] = { 0, 0, cpu_to_be32(ramsize) }; |
| char *filename; |
| int fdt_size; |
| void *fdt; |
| uint32_t tb_freq = CPU_FREQ; |
| uint32_t clock_freq = CPU_FREQ; |
| int offset; |
| |
| filename = qemu_find_file(QEMU_FILE_TYPE_BIOS, BINARY_DEVICE_TREE_FILE); |
| if (!filename) { |
| error_report("Couldn't find dtb file `%s'", BINARY_DEVICE_TREE_FILE); |
| exit(1); |
| } |
| fdt = load_device_tree(filename, &fdt_size); |
| if (!fdt) { |
| error_report("Couldn't load dtb file `%s'", filename); |
| g_free(filename); |
| exit(1); |
| } |
| g_free(filename); |
| |
| /* Manipulate device tree in memory. */ |
| |
| qemu_fdt_setprop(fdt, "/memory", "reg", mem_reg_property, |
| sizeof(mem_reg_property)); |
| |
| /* default FDT doesn't have a /chosen node... */ |
| qemu_fdt_add_subnode(fdt, "/chosen"); |
| |
| qemu_fdt_setprop_cell(fdt, "/chosen", "linux,initrd-start", initrd_base); |
| |
| qemu_fdt_setprop_cell(fdt, "/chosen", "linux,initrd-end", |
| (initrd_base + initrd_size)); |
| |
| qemu_fdt_setprop_string(fdt, "/chosen", "bootargs", kernel_cmdline); |
| |
| /* Copy data from the host device tree into the guest. Since the guest can |
| * directly access the timebase without host involvement, we must expose |
| * the correct frequencies. */ |
| if (kvm_enabled()) { |
| tb_freq = kvmppc_get_tbfreq(); |
| clock_freq = kvmppc_get_clockfreq(); |
| } |
| |
| qemu_fdt_setprop_cell(fdt, "/cpus/cpu@0", "clock-frequency", |
| clock_freq); |
| qemu_fdt_setprop_cell(fdt, "/cpus/cpu@0", "timebase-frequency", |
| tb_freq); |
| |
| /* Remove cpm node if it exists (it is not emulated) */ |
| offset = fdt_path_offset(fdt, "/cpm"); |
| if (offset >= 0) { |
| _FDT(fdt_nop_node(fdt, offset)); |
| } |
| |
| /* set serial port clocks */ |
| offset = fdt_node_offset_by_compatible(fdt, -1, "ns16550"); |
| while (offset >= 0) { |
| _FDT(fdt_setprop_cell(fdt, offset, "clock-frequency", UART_FREQ)); |
| offset = fdt_node_offset_by_compatible(fdt, offset, "ns16550"); |
| } |
| |
| /* some more clocks */ |
| qemu_fdt_setprop_cell(fdt, "/plb", "clock-frequency", |
| PLB_FREQ); |
| qemu_fdt_setprop_cell(fdt, "/plb/opb", "clock-frequency", |
| OPB_FREQ); |
| qemu_fdt_setprop_cell(fdt, "/plb/opb/ebc", "clock-frequency", |
| EBC_FREQ); |
| |
| rom_add_blob_fixed(BINARY_DEVICE_TREE_FILE, fdt, fdt_size, addr); |
| g_free(fdt); |
| |
| return fdt_size; |
| } |
| |
| /* Create reset TLB entries for BookE, mapping only the flash memory. */ |
| static void mmubooke_create_initial_mapping_uboot(CPUPPCState *env) |
| { |
| ppcemb_tlb_t *tlb = &env->tlb.tlbe[0]; |
| |
| /* on reset the flash is mapped by a shadow TLB, |
| * but since we don't implement them we need to use |
| * the same values U-Boot will use to avoid a fault. |
| */ |
| tlb->attr = 0; |
| tlb->prot = PAGE_VALID | ((PAGE_READ | PAGE_WRITE | PAGE_EXEC) << 4); |
| tlb->size = 0x10000000; /* up to 0xffffffff */ |
| tlb->EPN = 0xf0000000 & TARGET_PAGE_MASK; |
| tlb->RPN = (0xf0000000 & TARGET_PAGE_MASK) | 0x4; |
| tlb->PID = 0; |
| } |
| |
| /* Create reset TLB entries for BookE, spanning the 32bit addr space. */ |
| static void mmubooke_create_initial_mapping(CPUPPCState *env, |
| target_ulong va, |
| hwaddr pa) |
| { |
| ppcemb_tlb_t *tlb = &env->tlb.tlbe[0]; |
| |
| tlb->attr = 0; |
| tlb->prot = PAGE_VALID | ((PAGE_READ | PAGE_WRITE | PAGE_EXEC) << 4); |
| tlb->size = 1 << 31; /* up to 0x80000000 */ |
| tlb->EPN = va & TARGET_PAGE_MASK; |
| tlb->RPN = pa & TARGET_PAGE_MASK; |
| tlb->PID = 0; |
| } |
| |
| static void main_cpu_reset(void *opaque) |
| { |
| PowerPCCPU *cpu = opaque; |
| CPUPPCState *env = &cpu->env; |
| struct boot_info *bi = env->load_info; |
| |
| cpu_reset(CPU(cpu)); |
| |
| /* either we have a kernel to boot or we jump to U-Boot */ |
| if (bi->entry != UBOOT_ENTRY) { |
| env->gpr[1] = (16 * MiB) - 8; |
| env->gpr[3] = FDT_ADDR; |
| env->nip = bi->entry; |
| |
| /* Create a mapping for the kernel. */ |
| mmubooke_create_initial_mapping(env, 0, 0); |
| env->gpr[6] = tswap32(EPAPR_MAGIC); |
| env->gpr[7] = (16 * MiB) - 8; /* bi->ima_size; */ |
| |
| } else { |
| env->nip = UBOOT_ENTRY; |
| mmubooke_create_initial_mapping_uboot(env); |
| } |
| } |
| |
| static void sam460ex_init(MachineState *machine) |
| { |
| MemoryRegion *address_space_mem = get_system_memory(); |
| MemoryRegion *isa = g_new(MemoryRegion, 1); |
| MemoryRegion *ram_memories = g_new(MemoryRegion, SDRAM_NR_BANKS); |
| hwaddr ram_bases[SDRAM_NR_BANKS]; |
| hwaddr ram_sizes[SDRAM_NR_BANKS]; |
| MemoryRegion *l2cache_ram = g_new(MemoryRegion, 1); |
| qemu_irq *irqs, *uic[4]; |
| PCIBus *pci_bus; |
| PowerPCCPU *cpu; |
| CPUPPCState *env; |
| PPC4xxI2CState *i2c[2]; |
| hwaddr entry = UBOOT_ENTRY; |
| hwaddr loadaddr = 0; |
| target_long initrd_size = 0; |
| DeviceState *dev; |
| SysBusDevice *sbdev; |
| int success; |
| int i; |
| struct boot_info *boot_info; |
| const size_t smbus_eeprom_size = 8 * 256; |
| uint8_t *smbus_eeprom_buf = g_malloc0(smbus_eeprom_size); |
| |
| cpu = POWERPC_CPU(cpu_create(machine->cpu_type)); |
| env = &cpu->env; |
| if (env->mmu_model != POWERPC_MMU_BOOKE) { |
| error_report("Only MMU model BookE is supported by this machine."); |
| exit(1); |
| } |
| |
| #ifdef TARGET_PPCEMB |
| if (!qtest_enabled()) { |
| warn_report("qemu-system-ppcemb is deprecated, " |
| "please use qemu-system-ppc instead."); |
| } |
| #endif |
| |
| qemu_register_reset(main_cpu_reset, cpu); |
| boot_info = g_malloc0(sizeof(*boot_info)); |
| env->load_info = boot_info; |
| |
| ppc_booke_timers_init(cpu, CPU_FREQ, 0); |
| ppc_dcr_init(env, NULL, NULL); |
| |
| /* PLB arbitrer */ |
| ppc4xx_plb_init(env); |
| |
| /* interrupt controllers */ |
| irqs = g_malloc0(sizeof(*irqs) * PPCUIC_OUTPUT_NB); |
| irqs[PPCUIC_OUTPUT_INT] = ((qemu_irq *)env->irq_inputs)[PPC40x_INPUT_INT]; |
| irqs[PPCUIC_OUTPUT_CINT] = ((qemu_irq *)env->irq_inputs)[PPC40x_INPUT_CINT]; |
| uic[0] = ppcuic_init(env, irqs, 0xc0, 0, 1); |
| uic[1] = ppcuic_init(env, &uic[0][30], 0xd0, 0, 1); |
| uic[2] = ppcuic_init(env, &uic[0][10], 0xe0, 0, 1); |
| uic[3] = ppcuic_init(env, &uic[0][16], 0xf0, 0, 1); |
| |
| /* SDRAM controller */ |
| memset(ram_bases, 0, sizeof(ram_bases)); |
| memset(ram_sizes, 0, sizeof(ram_sizes)); |
| /* put all RAM on first bank because board has one slot |
| * and firmware only checks that */ |
| machine->ram_size = ppc4xx_sdram_adjust(machine->ram_size, 1, |
| ram_memories, ram_bases, ram_sizes, |
| ppc460ex_sdram_bank_sizes); |
| |
| /* FIXME: does 460EX have ECC interrupts? */ |
| ppc440_sdram_init(env, SDRAM_NR_BANKS, ram_memories, |
| ram_bases, ram_sizes, 1); |
| |
| /* generate SPD EEPROM data */ |
| for (i = 0; i < SDRAM_NR_BANKS; i++) { |
| generate_eeprom_spd(&smbus_eeprom_buf[i * 256], ram_sizes[i]); |
| } |
| generate_eeprom_serial(&smbus_eeprom_buf[4 * 256]); |
| generate_eeprom_serial(&smbus_eeprom_buf[6 * 256]); |
| |
| /* IIC controllers */ |
| dev = sysbus_create_simple(TYPE_PPC4xx_I2C, 0x4ef600700, uic[0][2]); |
| i2c[0] = PPC4xx_I2C(dev); |
| object_property_set_bool(OBJECT(dev), true, "realized", NULL); |
| smbus_eeprom_init(i2c[0]->bus, 8, smbus_eeprom_buf, smbus_eeprom_size); |
| g_free(smbus_eeprom_buf); |
| i2c_create_slave(i2c[0]->bus, "m41t80", 0x68); |
| |
| dev = sysbus_create_simple(TYPE_PPC4xx_I2C, 0x4ef600800, uic[0][3]); |
| i2c[1] = PPC4xx_I2C(dev); |
| |
| /* External bus controller */ |
| ppc405_ebc_init(env); |
| |
| /* CPR */ |
| ppc4xx_cpr_init(env); |
| |
| /* PLB to AHB bridge */ |
| ppc4xx_ahb_init(env); |
| |
| /* System DCRs */ |
| ppc4xx_sdr_init(env); |
| |
| /* MAL */ |
| ppc4xx_mal_init(env, 4, 16, &uic[2][3]); |
| |
| /* DMA */ |
| ppc4xx_dma_init(env, 0x200); |
| |
| /* 256K of L2 cache as memory */ |
| ppc4xx_l2sram_init(env); |
| /* FIXME: remove this after fixing l2sram mapping in ppc440_uc.c? */ |
| memory_region_init_ram(l2cache_ram, NULL, "ppc440.l2cache_ram", 256 * KiB, |
| &error_abort); |
| memory_region_add_subregion(address_space_mem, 0x400000000LL, l2cache_ram); |
| |
| /* USB */ |
| sysbus_create_simple(TYPE_PPC4xx_EHCI, 0x4bffd0400, uic[2][29]); |
| dev = qdev_create(NULL, "sysbus-ohci"); |
| qdev_prop_set_string(dev, "masterbus", "usb-bus.0"); |
| qdev_prop_set_uint32(dev, "num-ports", 6); |
| qdev_init_nofail(dev); |
| sbdev = SYS_BUS_DEVICE(dev); |
| sysbus_mmio_map(sbdev, 0, 0x4bffd0000); |
| sysbus_connect_irq(sbdev, 0, uic[2][30]); |
| usb_create_simple(usb_bus_find(-1), "usb-kbd"); |
| usb_create_simple(usb_bus_find(-1), "usb-mouse"); |
| |
| /* PCI bus */ |
| ppc460ex_pcie_init(env); |
| /* All PCI irqs are connected to the same UIC pin (cf. UBoot source) */ |
| dev = sysbus_create_simple("ppc440-pcix-host", 0xc0ec00000, uic[1][0]); |
| pci_bus = (PCIBus *)qdev_get_child_bus(dev, "pci.0"); |
| if (!pci_bus) { |
| error_report("couldn't create PCI controller!"); |
| exit(1); |
| } |
| memory_region_init_alias(isa, NULL, "isa_mmio", get_system_io(), |
| 0, 0x10000); |
| memory_region_add_subregion(get_system_memory(), 0xc08000000, isa); |
| |
| /* PCI devices */ |
| pci_create_simple(pci_bus, PCI_DEVFN(6, 0), "sm501"); |
| /* SoC has a single SATA port but we don't emulate that yet |
| * However, firmware and usual clients have driver for SiI311x |
| * so add one for convenience by default */ |
| if (defaults_enabled()) { |
| pci_create_simple(pci_bus, -1, "sii3112"); |
| } |
| |
| /* SoC has 4 UARTs |
| * but board has only one wired and two are present in fdt */ |
| if (serial_hd(0) != NULL) { |
| serial_mm_init(address_space_mem, 0x4ef600300, 0, uic[1][1], |
| PPC_SERIAL_MM_BAUDBASE, serial_hd(0), |
| DEVICE_BIG_ENDIAN); |
| } |
| if (serial_hd(1) != NULL) { |
| serial_mm_init(address_space_mem, 0x4ef600400, 0, uic[0][1], |
| PPC_SERIAL_MM_BAUDBASE, serial_hd(1), |
| DEVICE_BIG_ENDIAN); |
| } |
| |
| /* Load U-Boot image. */ |
| if (!machine->kernel_filename) { |
| success = sam460ex_load_uboot(); |
| if (success < 0) { |
| error_report("qemu: could not load firmware"); |
| exit(1); |
| } |
| } |
| |
| /* Load kernel. */ |
| if (machine->kernel_filename) { |
| success = load_uimage(machine->kernel_filename, &entry, &loadaddr, |
| NULL, NULL, NULL); |
| if (success < 0) { |
| uint64_t elf_entry, elf_lowaddr; |
| |
| success = load_elf(machine->kernel_filename, NULL, NULL, &elf_entry, |
| &elf_lowaddr, NULL, 1, PPC_ELF_MACHINE, 0, 0); |
| entry = elf_entry; |
| loadaddr = elf_lowaddr; |
| } |
| /* XXX try again as binary */ |
| if (success < 0) { |
| error_report("qemu: could not load kernel '%s'", |
| machine->kernel_filename); |
| exit(1); |
| } |
| } |
| |
| /* Load initrd. */ |
| if (machine->initrd_filename) { |
| initrd_size = load_image_targphys(machine->initrd_filename, |
| RAMDISK_ADDR, |
| machine->ram_size - RAMDISK_ADDR); |
| if (initrd_size < 0) { |
| error_report("qemu: could not load ram disk '%s' at %x", |
| machine->initrd_filename, RAMDISK_ADDR); |
| exit(1); |
| } |
| } |
| |
| /* If we're loading a kernel directly, we must load the device tree too. */ |
| if (machine->kernel_filename) { |
| int dt_size; |
| |
| dt_size = sam460ex_load_device_tree(FDT_ADDR, machine->ram_size, |
| RAMDISK_ADDR, initrd_size, |
| machine->kernel_cmdline); |
| |
| boot_info->dt_base = FDT_ADDR; |
| boot_info->dt_size = dt_size; |
| } |
| |
| boot_info->entry = entry; |
| } |
| |
| static void sam460ex_machine_init(MachineClass *mc) |
| { |
| mc->desc = "aCube Sam460ex"; |
| mc->init = sam460ex_init; |
| mc->default_cpu_type = POWERPC_CPU_TYPE_NAME("460exb"); |
| mc->default_ram_size = 512 * MiB; |
| } |
| |
| DEFINE_MACHINE("sam460ex", sam460ex_machine_init) |
