| /* |
| * ARM RealView Baseboard System emulation. |
| * |
| * Copyright (c) 2006-2007 CodeSourcery. |
| * Written by Paul Brook |
| * |
| * This code is licensed under the GPL. |
| */ |
| |
| #include "qemu/osdep.h" |
| #include "qapi/error.h" |
| #include "cpu.h" |
| #include "hw/sysbus.h" |
| #include "hw/arm/boot.h" |
| #include "hw/arm/primecell.h" |
| #include "hw/core/split-irq.h" |
| #include "hw/net/lan9118.h" |
| #include "hw/net/smc91c111.h" |
| #include "hw/pci/pci.h" |
| #include "hw/qdev-core.h" |
| #include "net/net.h" |
| #include "sysemu/sysemu.h" |
| #include "hw/boards.h" |
| #include "hw/i2c/i2c.h" |
| #include "qemu/error-report.h" |
| #include "hw/char/pl011.h" |
| #include "hw/cpu/a9mpcore.h" |
| #include "hw/intc/realview_gic.h" |
| #include "hw/irq.h" |
| #include "hw/i2c/arm_sbcon_i2c.h" |
| #include "hw/sd/sd.h" |
| #include "audio/audio.h" |
| #include "target/arm/cpu-qom.h" |
| |
| #define SMP_BOOT_ADDR 0xe0000000 |
| #define SMP_BOOTREG_ADDR 0x10000030 |
| |
| /* Board init. */ |
| |
| static struct arm_boot_info realview_binfo = { |
| .smp_loader_start = SMP_BOOT_ADDR, |
| .smp_bootreg_addr = SMP_BOOTREG_ADDR, |
| }; |
| |
| /* The following two lists must be consistent. */ |
| enum realview_board_type { |
| BOARD_EB, |
| BOARD_EB_MPCORE, |
| BOARD_PB_A8, |
| BOARD_PBX_A9, |
| }; |
| |
| static const int realview_board_id[] = { |
| 0x33b, |
| 0x33b, |
| 0x769, |
| 0x76d |
| }; |
| |
| static void split_irq_from_named(DeviceState *src, const char* outname, |
| qemu_irq out1, qemu_irq out2) { |
| DeviceState *splitter = qdev_new(TYPE_SPLIT_IRQ); |
| |
| qdev_prop_set_uint32(splitter, "num-lines", 2); |
| |
| qdev_realize_and_unref(splitter, NULL, &error_fatal); |
| |
| qdev_connect_gpio_out(splitter, 0, out1); |
| qdev_connect_gpio_out(splitter, 1, out2); |
| qdev_connect_gpio_out_named(src, outname, 0, |
| qdev_get_gpio_in(splitter, 0)); |
| } |
| |
| static void realview_init(MachineState *machine, |
| enum realview_board_type board_type) |
| { |
| ARMCPU *cpu = NULL; |
| CPUARMState *env; |
| MemoryRegion *sysmem = get_system_memory(); |
| MemoryRegion *ram_lo; |
| MemoryRegion *ram_hi = g_new(MemoryRegion, 1); |
| MemoryRegion *ram_alias = g_new(MemoryRegion, 1); |
| MemoryRegion *ram_hack = g_new(MemoryRegion, 1); |
| DeviceState *dev, *sysctl, *gpio2, *pl041; |
| SysBusDevice *busdev; |
| qemu_irq pic[64]; |
| PCIBus *pci_bus = NULL; |
| DriveInfo *dinfo; |
| I2CBus *i2c; |
| int n; |
| unsigned int smp_cpus = machine->smp.cpus; |
| qemu_irq cpu_irq[4]; |
| int is_mpcore = 0; |
| int is_pb = 0; |
| uint32_t proc_id = 0; |
| uint32_t sys_id; |
| ram_addr_t low_ram_size; |
| ram_addr_t ram_size = machine->ram_size; |
| hwaddr periphbase = 0; |
| |
| switch (board_type) { |
| case BOARD_EB: |
| break; |
| case BOARD_EB_MPCORE: |
| is_mpcore = 1; |
| periphbase = 0x10100000; |
| break; |
| case BOARD_PB_A8: |
| is_pb = 1; |
| break; |
| case BOARD_PBX_A9: |
| is_mpcore = 1; |
| is_pb = 1; |
| periphbase = 0x1f000000; |
| break; |
| } |
| |
| for (n = 0; n < smp_cpus; n++) { |
| Object *cpuobj = object_new(machine->cpu_type); |
| |
| /* By default A9,A15 and ARM1176 CPUs have EL3 enabled. This board |
| * does not currently support EL3 so the CPU EL3 property is disabled |
| * before realization. |
| */ |
| if (object_property_find(cpuobj, "has_el3")) { |
| object_property_set_bool(cpuobj, "has_el3", false, &error_fatal); |
| } |
| |
| if (is_pb && is_mpcore) { |
| object_property_set_int(cpuobj, "reset-cbar", periphbase, |
| &error_fatal); |
| } |
| |
| qdev_realize(DEVICE(cpuobj), NULL, &error_fatal); |
| |
| cpu_irq[n] = qdev_get_gpio_in(DEVICE(cpuobj), ARM_CPU_IRQ); |
| } |
| cpu = ARM_CPU(first_cpu); |
| env = &cpu->env; |
| if (arm_feature(env, ARM_FEATURE_V7)) { |
| if (is_mpcore) { |
| proc_id = 0x0c000000; |
| } else { |
| proc_id = 0x0e000000; |
| } |
| } else if (arm_feature(env, ARM_FEATURE_V6K)) { |
| proc_id = 0x06000000; |
| } else if (arm_feature(env, ARM_FEATURE_V6)) { |
| proc_id = 0x04000000; |
| } else { |
| proc_id = 0x02000000; |
| } |
| |
| if (is_pb && ram_size > 0x20000000) { |
| /* Core tile RAM. */ |
| ram_lo = g_new(MemoryRegion, 1); |
| low_ram_size = ram_size - 0x20000000; |
| ram_size = 0x20000000; |
| memory_region_init_ram(ram_lo, NULL, "realview.lowmem", low_ram_size, |
| &error_fatal); |
| memory_region_add_subregion(sysmem, 0x20000000, ram_lo); |
| } |
| |
| memory_region_init_ram(ram_hi, NULL, "realview.highmem", ram_size, |
| &error_fatal); |
| low_ram_size = ram_size; |
| if (low_ram_size > 0x10000000) |
| low_ram_size = 0x10000000; |
| /* SDRAM at address zero. */ |
| memory_region_init_alias(ram_alias, NULL, "realview.alias", |
| ram_hi, 0, low_ram_size); |
| memory_region_add_subregion(sysmem, 0, ram_alias); |
| if (is_pb) { |
| /* And again at a high address. */ |
| memory_region_add_subregion(sysmem, 0x70000000, ram_hi); |
| } else { |
| ram_size = low_ram_size; |
| } |
| |
| sys_id = is_pb ? 0x01780500 : 0xc1400400; |
| sysctl = qdev_new("realview_sysctl"); |
| qdev_prop_set_uint32(sysctl, "sys_id", sys_id); |
| qdev_prop_set_uint32(sysctl, "proc_id", proc_id); |
| sysbus_realize_and_unref(SYS_BUS_DEVICE(sysctl), &error_fatal); |
| sysbus_mmio_map(SYS_BUS_DEVICE(sysctl), 0, 0x10000000); |
| |
| if (is_mpcore) { |
| dev = qdev_new(is_pb ? TYPE_A9MPCORE_PRIV : "realview_mpcore"); |
| qdev_prop_set_uint32(dev, "num-cpu", smp_cpus); |
| busdev = SYS_BUS_DEVICE(dev); |
| sysbus_realize_and_unref(busdev, &error_fatal); |
| sysbus_mmio_map(busdev, 0, periphbase); |
| for (n = 0; n < smp_cpus; n++) { |
| sysbus_connect_irq(busdev, n, cpu_irq[n]); |
| } |
| sysbus_create_varargs("l2x0", periphbase + 0x2000, NULL); |
| /* Both A9 and 11MPCore put the GIC CPU i/f at base + 0x100 */ |
| realview_binfo.gic_cpu_if_addr = periphbase + 0x100; |
| } else { |
| uint32_t gic_addr = is_pb ? 0x1e000000 : 0x10040000; |
| /* For now just create the nIRQ GIC, and ignore the others. */ |
| dev = sysbus_create_simple(TYPE_REALVIEW_GIC, gic_addr, cpu_irq[0]); |
| } |
| for (n = 0; n < 64; n++) { |
| pic[n] = qdev_get_gpio_in(dev, n); |
| } |
| |
| pl041 = qdev_new("pl041"); |
| qdev_prop_set_uint32(pl041, "nc_fifo_depth", 512); |
| if (machine->audiodev) { |
| qdev_prop_set_string(pl041, "audiodev", machine->audiodev); |
| } |
| sysbus_realize_and_unref(SYS_BUS_DEVICE(pl041), &error_fatal); |
| sysbus_mmio_map(SYS_BUS_DEVICE(pl041), 0, 0x10004000); |
| sysbus_connect_irq(SYS_BUS_DEVICE(pl041), 0, pic[19]); |
| |
| sysbus_create_simple("pl050_keyboard", 0x10006000, pic[20]); |
| sysbus_create_simple("pl050_mouse", 0x10007000, pic[21]); |
| |
| pl011_create(0x10009000, pic[12], serial_hd(0)); |
| pl011_create(0x1000a000, pic[13], serial_hd(1)); |
| pl011_create(0x1000b000, pic[14], serial_hd(2)); |
| pl011_create(0x1000c000, pic[15], serial_hd(3)); |
| |
| /* DMA controller is optional, apparently. */ |
| dev = qdev_new("pl081"); |
| object_property_set_link(OBJECT(dev), "downstream", OBJECT(sysmem), |
| &error_fatal); |
| busdev = SYS_BUS_DEVICE(dev); |
| sysbus_realize_and_unref(busdev, &error_fatal); |
| sysbus_mmio_map(busdev, 0, 0x10030000); |
| sysbus_connect_irq(busdev, 0, pic[24]); |
| |
| sysbus_create_simple("sp804", 0x10011000, pic[4]); |
| sysbus_create_simple("sp804", 0x10012000, pic[5]); |
| |
| sysbus_create_simple("pl061", 0x10013000, pic[6]); |
| sysbus_create_simple("pl061", 0x10014000, pic[7]); |
| gpio2 = sysbus_create_simple("pl061", 0x10015000, pic[8]); |
| |
| sysbus_create_simple("pl111", 0x10020000, pic[23]); |
| |
| dev = sysbus_create_varargs("pl181", 0x10005000, pic[17], pic[18], NULL); |
| /* Wire up MMC card detect and read-only signals. These have |
| * to go to both the PL061 GPIO and the sysctl register. |
| * Note that the PL181 orders these lines (readonly,inserted) |
| * and the PL061 has them the other way about. Also the card |
| * detect line is inverted. |
| */ |
| split_irq_from_named(dev, "card-read-only", |
| qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_WPROT), |
| qdev_get_gpio_in(gpio2, 1)); |
| |
| split_irq_from_named(dev, "card-inserted", |
| qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_CARDIN), |
| qemu_irq_invert(qdev_get_gpio_in(gpio2, 0))); |
| |
| dinfo = drive_get(IF_SD, 0, 0); |
| if (dinfo) { |
| DeviceState *card; |
| |
| card = qdev_new(TYPE_SD_CARD); |
| qdev_prop_set_drive_err(card, "drive", blk_by_legacy_dinfo(dinfo), |
| &error_fatal); |
| qdev_realize_and_unref(card, qdev_get_child_bus(dev, "sd-bus"), |
| &error_fatal); |
| } |
| |
| sysbus_create_simple("pl031", 0x10017000, pic[10]); |
| |
| if (!is_pb) { |
| dev = qdev_new("realview_pci"); |
| busdev = SYS_BUS_DEVICE(dev); |
| sysbus_realize_and_unref(busdev, &error_fatal); |
| sysbus_mmio_map(busdev, 0, 0x10019000); /* PCI controller registers */ |
| sysbus_mmio_map(busdev, 1, 0x60000000); /* PCI self-config */ |
| sysbus_mmio_map(busdev, 2, 0x61000000); /* PCI config */ |
| sysbus_mmio_map(busdev, 3, 0x62000000); /* PCI I/O */ |
| sysbus_mmio_map(busdev, 4, 0x63000000); /* PCI memory window 1 */ |
| sysbus_mmio_map(busdev, 5, 0x64000000); /* PCI memory window 2 */ |
| sysbus_mmio_map(busdev, 6, 0x68000000); /* PCI memory window 3 */ |
| sysbus_connect_irq(busdev, 0, pic[48]); |
| sysbus_connect_irq(busdev, 1, pic[49]); |
| sysbus_connect_irq(busdev, 2, pic[50]); |
| sysbus_connect_irq(busdev, 3, pic[51]); |
| pci_bus = (PCIBus *)qdev_get_child_bus(dev, "pci"); |
| if (machine_usb(machine)) { |
| pci_create_simple(pci_bus, -1, "pci-ohci"); |
| } |
| n = drive_get_max_bus(IF_SCSI); |
| while (n >= 0) { |
| dev = DEVICE(pci_create_simple(pci_bus, -1, "lsi53c895a")); |
| lsi53c8xx_handle_legacy_cmdline(dev); |
| n--; |
| } |
| } |
| |
| if (qemu_find_nic_info(is_pb ? "lan9118" : "smc91c111", true, NULL)) { |
| if (is_pb) { |
| lan9118_init(0x4e000000, pic[28]); |
| } else { |
| smc91c111_init(0x4e000000, pic[28]); |
| } |
| } |
| |
| if (pci_bus) { |
| pci_init_nic_devices(pci_bus, "rtl8139"); |
| } |
| |
| dev = sysbus_create_simple(TYPE_ARM_SBCON_I2C, 0x10002000, NULL); |
| i2c = (I2CBus *)qdev_get_child_bus(dev, "i2c"); |
| i2c_slave_create_simple(i2c, "ds1338", 0x68); |
| |
| /* Memory map for RealView Emulation Baseboard: */ |
| /* 0x10000000 System registers. */ |
| /* 0x10001000 System controller. */ |
| /* 0x10002000 Two-Wire Serial Bus. */ |
| /* 0x10003000 Reserved. */ |
| /* 0x10004000 AACI. */ |
| /* 0x10005000 MCI. */ |
| /* 0x10006000 KMI0. */ |
| /* 0x10007000 KMI1. */ |
| /* 0x10008000 Character LCD. (EB) */ |
| /* 0x10009000 UART0. */ |
| /* 0x1000a000 UART1. */ |
| /* 0x1000b000 UART2. */ |
| /* 0x1000c000 UART3. */ |
| /* 0x1000d000 SSPI. */ |
| /* 0x1000e000 SCI. */ |
| /* 0x1000f000 Reserved. */ |
| /* 0x10010000 Watchdog. */ |
| /* 0x10011000 Timer 0+1. */ |
| /* 0x10012000 Timer 2+3. */ |
| /* 0x10013000 GPIO 0. */ |
| /* 0x10014000 GPIO 1. */ |
| /* 0x10015000 GPIO 2. */ |
| /* 0x10002000 Two-Wire Serial Bus - DVI. (PB) */ |
| /* 0x10017000 RTC. */ |
| /* 0x10018000 DMC. */ |
| /* 0x10019000 PCI controller config. */ |
| /* 0x10020000 CLCD. */ |
| /* 0x10030000 DMA Controller. */ |
| /* 0x10040000 GIC1. (EB) */ |
| /* 0x10050000 GIC2. (EB) */ |
| /* 0x10060000 GIC3. (EB) */ |
| /* 0x10070000 GIC4. (EB) */ |
| /* 0x10080000 SMC. */ |
| /* 0x1e000000 GIC1. (PB) */ |
| /* 0x1e001000 GIC2. (PB) */ |
| /* 0x1e002000 GIC3. (PB) */ |
| /* 0x1e003000 GIC4. (PB) */ |
| /* 0x40000000 NOR flash. */ |
| /* 0x44000000 DoC flash. */ |
| /* 0x48000000 SRAM. */ |
| /* 0x4c000000 Configuration flash. */ |
| /* 0x4e000000 Ethernet. */ |
| /* 0x4f000000 USB. */ |
| /* 0x50000000 PISMO. */ |
| /* 0x54000000 PISMO. */ |
| /* 0x58000000 PISMO. */ |
| /* 0x5c000000 PISMO. */ |
| /* 0x60000000 PCI. */ |
| /* 0x60000000 PCI Self Config. */ |
| /* 0x61000000 PCI Config. */ |
| /* 0x62000000 PCI IO. */ |
| /* 0x63000000 PCI mem 0. */ |
| /* 0x64000000 PCI mem 1. */ |
| /* 0x68000000 PCI mem 2. */ |
| |
| /* ??? Hack to map an additional page of ram for the secondary CPU |
| startup code. I guess this works on real hardware because the |
| BootROM happens to be in ROM/flash or in memory that isn't clobbered |
| until after Linux boots the secondary CPUs. */ |
| memory_region_init_ram(ram_hack, NULL, "realview.hack", 0x1000, |
| &error_fatal); |
| memory_region_add_subregion(sysmem, SMP_BOOT_ADDR, ram_hack); |
| |
| realview_binfo.ram_size = ram_size; |
| realview_binfo.board_id = realview_board_id[board_type]; |
| realview_binfo.loader_start = (board_type == BOARD_PB_A8 ? 0x70000000 : 0); |
| arm_load_kernel(cpu, machine, &realview_binfo); |
| } |
| |
| static void realview_eb_init(MachineState *machine) |
| { |
| realview_init(machine, BOARD_EB); |
| } |
| |
| static void realview_eb_mpcore_init(MachineState *machine) |
| { |
| realview_init(machine, BOARD_EB_MPCORE); |
| } |
| |
| static void realview_pb_a8_init(MachineState *machine) |
| { |
| realview_init(machine, BOARD_PB_A8); |
| } |
| |
| static void realview_pbx_a9_init(MachineState *machine) |
| { |
| realview_init(machine, BOARD_PBX_A9); |
| } |
| |
| static void realview_eb_class_init(ObjectClass *oc, void *data) |
| { |
| MachineClass *mc = MACHINE_CLASS(oc); |
| |
| mc->desc = "ARM RealView Emulation Baseboard (ARM926EJ-S)"; |
| mc->init = realview_eb_init; |
| mc->block_default_type = IF_SCSI; |
| mc->ignore_memory_transaction_failures = true; |
| mc->default_cpu_type = ARM_CPU_TYPE_NAME("arm926"); |
| |
| machine_add_audiodev_property(mc); |
| } |
| |
| static const TypeInfo realview_eb_type = { |
| .name = MACHINE_TYPE_NAME("realview-eb"), |
| .parent = TYPE_MACHINE, |
| .class_init = realview_eb_class_init, |
| }; |
| |
| static void realview_eb_mpcore_class_init(ObjectClass *oc, void *data) |
| { |
| MachineClass *mc = MACHINE_CLASS(oc); |
| |
| mc->desc = "ARM RealView Emulation Baseboard (ARM11MPCore)"; |
| mc->init = realview_eb_mpcore_init; |
| mc->block_default_type = IF_SCSI; |
| mc->max_cpus = 4; |
| mc->ignore_memory_transaction_failures = true; |
| mc->default_cpu_type = ARM_CPU_TYPE_NAME("arm11mpcore"); |
| |
| machine_add_audiodev_property(mc); |
| } |
| |
| static const TypeInfo realview_eb_mpcore_type = { |
| .name = MACHINE_TYPE_NAME("realview-eb-mpcore"), |
| .parent = TYPE_MACHINE, |
| .class_init = realview_eb_mpcore_class_init, |
| }; |
| |
| static void realview_pb_a8_class_init(ObjectClass *oc, void *data) |
| { |
| MachineClass *mc = MACHINE_CLASS(oc); |
| |
| mc->desc = "ARM RealView Platform Baseboard for Cortex-A8"; |
| mc->init = realview_pb_a8_init; |
| mc->ignore_memory_transaction_failures = true; |
| mc->default_cpu_type = ARM_CPU_TYPE_NAME("cortex-a8"); |
| |
| machine_add_audiodev_property(mc); |
| } |
| |
| static const TypeInfo realview_pb_a8_type = { |
| .name = MACHINE_TYPE_NAME("realview-pb-a8"), |
| .parent = TYPE_MACHINE, |
| .class_init = realview_pb_a8_class_init, |
| }; |
| |
| static void realview_pbx_a9_class_init(ObjectClass *oc, void *data) |
| { |
| MachineClass *mc = MACHINE_CLASS(oc); |
| |
| mc->desc = "ARM RealView Platform Baseboard Explore for Cortex-A9"; |
| mc->init = realview_pbx_a9_init; |
| mc->max_cpus = 4; |
| mc->ignore_memory_transaction_failures = true; |
| mc->default_cpu_type = ARM_CPU_TYPE_NAME("cortex-a9"); |
| |
| machine_add_audiodev_property(mc); |
| } |
| |
| static const TypeInfo realview_pbx_a9_type = { |
| .name = MACHINE_TYPE_NAME("realview-pbx-a9"), |
| .parent = TYPE_MACHINE, |
| .class_init = realview_pbx_a9_class_init, |
| }; |
| |
| static void realview_machine_init(void) |
| { |
| type_register_static(&realview_eb_type); |
| type_register_static(&realview_eb_mpcore_type); |
| type_register_static(&realview_pb_a8_type); |
| type_register_static(&realview_pbx_a9_type); |
| } |
| |
| type_init(realview_machine_init) |
