| /* |
| * MAX7310 8-port GPIO expansion chip. |
| * |
| * Copyright (c) 2006 Openedhand Ltd. |
| * Written by Andrzej Zaborowski <balrog@zabor.org> |
| * |
| * This file is licensed under GNU GPL. |
| */ |
| |
| #include "hw.h" |
| #include "i2c.h" |
| |
| struct max7310_s { |
| i2c_slave i2c; |
| int i2c_command_byte; |
| int len; |
| |
| uint8_t level; |
| uint8_t direction; |
| uint8_t polarity; |
| uint8_t status; |
| uint8_t command; |
| qemu_irq handler[8]; |
| qemu_irq *gpio_in; |
| }; |
| |
| void max7310_reset(i2c_slave *i2c) |
| { |
| struct max7310_s *s = (struct max7310_s *) i2c; |
| s->level &= s->direction; |
| s->direction = 0xff; |
| s->polarity = 0xf0; |
| s->status = 0x01; |
| s->command = 0x00; |
| } |
| |
| static int max7310_rx(i2c_slave *i2c) |
| { |
| struct max7310_s *s = (struct max7310_s *) i2c; |
| |
| switch (s->command) { |
| case 0x00: /* Input port */ |
| return s->level ^ s->polarity; |
| break; |
| |
| case 0x01: /* Output port */ |
| return s->level & ~s->direction; |
| break; |
| |
| case 0x02: /* Polarity inversion */ |
| return s->polarity; |
| |
| case 0x03: /* Configuration */ |
| return s->direction; |
| |
| case 0x04: /* Timeout */ |
| return s->status; |
| break; |
| |
| case 0xff: /* Reserved */ |
| return 0xff; |
| |
| default: |
| #ifdef VERBOSE |
| printf("%s: unknown register %02x\n", __FUNCTION__, s->command); |
| #endif |
| break; |
| } |
| return 0xff; |
| } |
| |
| static int max7310_tx(i2c_slave *i2c, uint8_t data) |
| { |
| struct max7310_s *s = (struct max7310_s *) i2c; |
| uint8_t diff; |
| int line; |
| |
| if (s->len ++ > 1) { |
| #ifdef VERBOSE |
| printf("%s: message too long (%i bytes)\n", __FUNCTION__, s->len); |
| #endif |
| return 1; |
| } |
| |
| if (s->i2c_command_byte) { |
| s->command = data; |
| s->i2c_command_byte = 0; |
| return 0; |
| } |
| |
| switch (s->command) { |
| case 0x01: /* Output port */ |
| for (diff = (data ^ s->level) & ~s->direction; diff; |
| diff &= ~(1 << line)) { |
| line = ffs(diff) - 1; |
| if (s->handler[line]) |
| qemu_set_irq(s->handler[line], (data >> line) & 1); |
| } |
| s->level = (s->level & s->direction) | (data & ~s->direction); |
| break; |
| |
| case 0x02: /* Polarity inversion */ |
| s->polarity = data; |
| break; |
| |
| case 0x03: /* Configuration */ |
| s->level &= ~(s->direction ^ data); |
| s->direction = data; |
| break; |
| |
| case 0x04: /* Timeout */ |
| s->status = data; |
| break; |
| |
| case 0x00: /* Input port - ignore writes */ |
| break; |
| default: |
| #ifdef VERBOSE |
| printf("%s: unknown register %02x\n", __FUNCTION__, s->command); |
| #endif |
| return 1; |
| } |
| |
| return 0; |
| } |
| |
| static void max7310_event(i2c_slave *i2c, enum i2c_event event) |
| { |
| struct max7310_s *s = (struct max7310_s *) i2c; |
| s->len = 0; |
| |
| switch (event) { |
| case I2C_START_SEND: |
| s->i2c_command_byte = 1; |
| break; |
| case I2C_FINISH: |
| #ifdef VERBOSE |
| if (s->len == 1) |
| printf("%s: message too short (%i bytes)\n", __FUNCTION__, s->len); |
| #endif |
| break; |
| default: |
| break; |
| } |
| } |
| |
| static void max7310_save(QEMUFile *f, void *opaque) |
| { |
| struct max7310_s *s = (struct max7310_s *) opaque; |
| |
| qemu_put_be32(f, s->i2c_command_byte); |
| qemu_put_be32(f, s->len); |
| |
| qemu_put_8s(f, &s->level); |
| qemu_put_8s(f, &s->direction); |
| qemu_put_8s(f, &s->polarity); |
| qemu_put_8s(f, &s->status); |
| qemu_put_8s(f, &s->command); |
| |
| i2c_slave_save(f, &s->i2c); |
| } |
| |
| static int max7310_load(QEMUFile *f, void *opaque, int version_id) |
| { |
| struct max7310_s *s = (struct max7310_s *) opaque; |
| |
| s->i2c_command_byte = qemu_get_be32(f); |
| s->len = qemu_get_be32(f); |
| |
| qemu_get_8s(f, &s->level); |
| qemu_get_8s(f, &s->direction); |
| qemu_get_8s(f, &s->polarity); |
| qemu_get_8s(f, &s->status); |
| qemu_get_8s(f, &s->command); |
| |
| i2c_slave_load(f, &s->i2c); |
| return 0; |
| } |
| |
| static void max7310_gpio_set(void *opaque, int line, int level) |
| { |
| struct max7310_s *s = (struct max7310_s *) opaque; |
| if (line >= ARRAY_SIZE(s->handler) || line < 0) |
| hw_error("bad GPIO line"); |
| |
| if (level) |
| s->level |= s->direction & (1 << line); |
| else |
| s->level &= ~(s->direction & (1 << line)); |
| } |
| |
| /* MAX7310 is SMBus-compatible (can be used with only SMBus protocols), |
| * but also accepts sequences that are not SMBus so return an I2C device. */ |
| struct i2c_slave *max7310_init(i2c_bus *bus) |
| { |
| struct max7310_s *s = (struct max7310_s *) |
| i2c_slave_init(bus, 0, sizeof(struct max7310_s)); |
| s->i2c.event = max7310_event; |
| s->i2c.recv = max7310_rx; |
| s->i2c.send = max7310_tx; |
| s->gpio_in = qemu_allocate_irqs(max7310_gpio_set, s, |
| ARRAY_SIZE(s->handler)); |
| |
| max7310_reset(&s->i2c); |
| |
| register_savevm("max7310", -1, 0, max7310_save, max7310_load, s); |
| |
| return &s->i2c; |
| } |
| |
| qemu_irq *max7310_gpio_in_get(i2c_slave *i2c) |
| { |
| struct max7310_s *s = (struct max7310_s *) i2c; |
| return s->gpio_in; |
| } |
| |
| void max7310_gpio_out_set(i2c_slave *i2c, int line, qemu_irq handler) |
| { |
| struct max7310_s *s = (struct max7310_s *) i2c; |
| if (line >= ARRAY_SIZE(s->handler) || line < 0) |
| hw_error("bad GPIO line"); |
| |
| s->handler[line] = handler; |
| } |