|  | /* | 
|  | * QEMU TEWS TPCI200 IndustryPack carrier emulation | 
|  | * | 
|  | * Copyright (C) 2012 Igalia, S.L. | 
|  | * Author: Alberto Garcia <berto@igalia.com> | 
|  | * | 
|  | * This code is licensed under the GNU GPL v2 or (at your option) any | 
|  | * later version. | 
|  | */ | 
|  |  | 
|  | #include "qemu/osdep.h" | 
|  | #include "qemu/units.h" | 
|  | #include "hw/ipack/ipack.h" | 
|  | #include "hw/irq.h" | 
|  | #include "hw/pci/pci_device.h" | 
|  | #include "migration/vmstate.h" | 
|  | #include "qemu/bitops.h" | 
|  | #include "qemu/module.h" | 
|  | #include "qom/object.h" | 
|  |  | 
|  | /* #define DEBUG_TPCI */ | 
|  |  | 
|  | #ifdef DEBUG_TPCI | 
|  | #define DPRINTF(fmt, ...) \ | 
|  | do { fprintf(stderr, "TPCI200: " fmt, ## __VA_ARGS__); } while (0) | 
|  | #else | 
|  | #define DPRINTF(fmt, ...) do { } while (0) | 
|  | #endif | 
|  |  | 
|  | #define N_MODULES 4 | 
|  |  | 
|  | #define IP_ID_SPACE  2 | 
|  | #define IP_INT_SPACE 3 | 
|  | #define IP_IO_SPACE_ADDR_MASK  0x7F | 
|  | #define IP_ID_SPACE_ADDR_MASK  0x3F | 
|  | #define IP_INT_SPACE_ADDR_MASK 0x3F | 
|  |  | 
|  | #define STATUS_INT(IP, INTNO) BIT((IP) * 2 + (INTNO)) | 
|  | #define STATUS_TIME(IP)       BIT((IP) + 12) | 
|  | #define STATUS_ERR_ANY        0xF00 | 
|  |  | 
|  | #define CTRL_CLKRATE          BIT(0) | 
|  | #define CTRL_RECOVER          BIT(1) | 
|  | #define CTRL_TIME_INT         BIT(2) | 
|  | #define CTRL_ERR_INT          BIT(3) | 
|  | #define CTRL_INT_EDGE(INTNO)  BIT(4 + (INTNO)) | 
|  | #define CTRL_INT(INTNO)       BIT(6 + (INTNO)) | 
|  |  | 
|  | #define REG_REV_ID    0x00 | 
|  | #define REG_IP_A_CTRL 0x02 | 
|  | #define REG_IP_B_CTRL 0x04 | 
|  | #define REG_IP_C_CTRL 0x06 | 
|  | #define REG_IP_D_CTRL 0x08 | 
|  | #define REG_RESET     0x0A | 
|  | #define REG_STATUS    0x0C | 
|  | #define IP_N_FROM_REG(REG) ((REG) / 2 - 1) | 
|  |  | 
|  | struct TPCI200State { | 
|  | PCIDevice dev; | 
|  | IPackBus bus; | 
|  | MemoryRegion mmio; | 
|  | MemoryRegion io; | 
|  | MemoryRegion las0; | 
|  | MemoryRegion las1; | 
|  | MemoryRegion las2; | 
|  | MemoryRegion las3; | 
|  | bool big_endian[3]; | 
|  | uint8_t ctrl[N_MODULES]; | 
|  | uint16_t status; | 
|  | uint8_t int_set; | 
|  | }; | 
|  |  | 
|  | #define TYPE_TPCI200 "tpci200" | 
|  |  | 
|  | OBJECT_DECLARE_SIMPLE_TYPE(TPCI200State, TPCI200) | 
|  |  | 
|  | static const uint8_t local_config_regs[] = { | 
|  | 0x00, 0xFF, 0xFF, 0x0F, 0x00, 0xFC, 0xFF, 0x0F, 0x00, 0x00, 0x00, | 
|  | 0x0E, 0x00, 0x00, 0x00, 0x0F, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, | 
|  | 0x00, 0x08, 0x01, 0x00, 0x00, 0x04, 0x01, 0x00, 0x00, 0x00, 0x01, | 
|  | 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0xA0, 0x60, 0x41, 0xD4, | 
|  | 0xA2, 0x20, 0x41, 0x14, 0xA2, 0x20, 0x41, 0x14, 0xA2, 0x20, 0x01, | 
|  | 0x14, 0x00, 0x00, 0x00, 0x00, 0x81, 0x00, 0x00, 0x08, 0x01, 0x02, | 
|  | 0x00, 0x04, 0x01, 0x00, 0x00, 0x01, 0x01, 0x00, 0x80, 0x02, 0x41, | 
|  | 0x00, 0x00, 0x00, 0x00, 0x40, 0x7A, 0x00, 0x52, 0x92, 0x24, 0x02 | 
|  | }; | 
|  |  | 
|  | static void adjust_addr(bool big_endian, hwaddr *addr, unsigned size) | 
|  | { | 
|  | /* During 8 bit access in big endian mode, | 
|  | odd and even addresses are swapped */ | 
|  | if (big_endian && size == 1) { | 
|  | *addr ^= 1; | 
|  | } | 
|  | } | 
|  |  | 
|  | static uint64_t adjust_value(bool big_endian, uint64_t *val, unsigned size) | 
|  | { | 
|  | /* Local spaces only support 8/16 bit access, | 
|  | * so there's no need to care for sizes > 2 */ | 
|  | if (big_endian && size == 2) { | 
|  | *val = bswap16(*val); | 
|  | } | 
|  | return *val; | 
|  | } | 
|  |  | 
|  | static void tpci200_set_irq(void *opaque, int intno, int level) | 
|  | { | 
|  | IPackDevice *ip = opaque; | 
|  | IPackBus *bus = IPACK_BUS(qdev_get_parent_bus(DEVICE(ip))); | 
|  | PCIDevice *pcidev = PCI_DEVICE(BUS(bus)->parent); | 
|  | TPCI200State *dev = TPCI200(pcidev); | 
|  | unsigned ip_n = ip->slot; | 
|  | uint16_t prev_status = dev->status; | 
|  |  | 
|  | assert(ip->slot >= 0 && ip->slot < N_MODULES); | 
|  |  | 
|  | /* The requested interrupt must be enabled in the IP CONTROL | 
|  | * register */ | 
|  | if (!(dev->ctrl[ip_n] & CTRL_INT(intno))) { | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* Update the interrupt status in the IP STATUS register */ | 
|  | if (level) { | 
|  | dev->status |=  STATUS_INT(ip_n, intno); | 
|  | } else { | 
|  | dev->status &= ~STATUS_INT(ip_n, intno); | 
|  | } | 
|  |  | 
|  | /* Return if there are no changes */ | 
|  | if (dev->status == prev_status) { | 
|  | return; | 
|  | } | 
|  |  | 
|  | DPRINTF("IP %u INT%u#: %u\n", ip_n, intno, level); | 
|  |  | 
|  | /* Check if the interrupt is edge sensitive */ | 
|  | if (dev->ctrl[ip_n] & CTRL_INT_EDGE(intno)) { | 
|  | if (level) { | 
|  | pci_set_irq(&dev->dev, !dev->int_set); | 
|  | pci_set_irq(&dev->dev,  dev->int_set); | 
|  | } | 
|  | } else { | 
|  | unsigned i, j; | 
|  | uint16_t level_status = dev->status; | 
|  |  | 
|  | /* Check if there are any level sensitive interrupts set by | 
|  | removing the ones that are edge sensitive from the status | 
|  | register */ | 
|  | for (i = 0; i < N_MODULES; i++) { | 
|  | for (j = 0; j < 2; j++) { | 
|  | if (dev->ctrl[i] & CTRL_INT_EDGE(j)) { | 
|  | level_status &= ~STATUS_INT(i, j); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | if (level_status && !dev->int_set) { | 
|  | pci_irq_assert(&dev->dev); | 
|  | dev->int_set = 1; | 
|  | } else if (!level_status && dev->int_set) { | 
|  | pci_irq_deassert(&dev->dev); | 
|  | dev->int_set = 0; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static uint64_t tpci200_read_cfg(void *opaque, hwaddr addr, unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | uint8_t ret = 0; | 
|  | if (addr < ARRAY_SIZE(local_config_regs)) { | 
|  | ret = local_config_regs[addr]; | 
|  | } | 
|  | /* Endianness is stored in the first bit of these registers */ | 
|  | if ((addr == 0x2b && s->big_endian[0]) || | 
|  | (addr == 0x2f && s->big_endian[1]) || | 
|  | (addr == 0x33 && s->big_endian[2])) { | 
|  | ret |= 1; | 
|  | } | 
|  | DPRINTF("Read from LCR 0x%x: 0x%x\n", (unsigned) addr, (unsigned) ret); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void tpci200_write_cfg(void *opaque, hwaddr addr, uint64_t val, | 
|  | unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | /* Endianness is stored in the first bit of these registers */ | 
|  | if (addr == 0x2b || addr == 0x2f || addr == 0x33) { | 
|  | unsigned las = (addr - 0x2b) / 4; | 
|  | s->big_endian[las] = val & 1; | 
|  | DPRINTF("LAS%u big endian mode: %u\n", las, (unsigned) val & 1); | 
|  | } else { | 
|  | DPRINTF("Write to LCR 0x%x: 0x%x\n", (unsigned) addr, (unsigned) val); | 
|  | } | 
|  | } | 
|  |  | 
|  | static uint64_t tpci200_read_las0(void *opaque, hwaddr addr, unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | uint64_t ret = 0; | 
|  |  | 
|  | switch (addr) { | 
|  |  | 
|  | case REG_REV_ID: | 
|  | DPRINTF("Read REVISION ID\n"); /* Current value is 0x00 */ | 
|  | break; | 
|  |  | 
|  | case REG_IP_A_CTRL: | 
|  | case REG_IP_B_CTRL: | 
|  | case REG_IP_C_CTRL: | 
|  | case REG_IP_D_CTRL: | 
|  | { | 
|  | unsigned ip_n = IP_N_FROM_REG(addr); | 
|  | ret = s->ctrl[ip_n]; | 
|  | DPRINTF("Read IP %c CONTROL: 0x%x\n", 'A' + ip_n, (unsigned) ret); | 
|  | } | 
|  | break; | 
|  |  | 
|  | case REG_RESET: | 
|  | DPRINTF("Read RESET\n"); /* Not implemented */ | 
|  | break; | 
|  |  | 
|  | case REG_STATUS: | 
|  | ret = s->status; | 
|  | DPRINTF("Read STATUS: 0x%x\n", (unsigned) ret); | 
|  | break; | 
|  |  | 
|  | /* Reserved */ | 
|  | default: | 
|  | DPRINTF("Unsupported read from LAS0 0x%x\n", (unsigned) addr); | 
|  | break; | 
|  | } | 
|  |  | 
|  | return adjust_value(s->big_endian[0], &ret, size); | 
|  | } | 
|  |  | 
|  | static void tpci200_write_las0(void *opaque, hwaddr addr, uint64_t val, | 
|  | unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  |  | 
|  | adjust_value(s->big_endian[0], &val, size); | 
|  |  | 
|  | switch (addr) { | 
|  |  | 
|  | case REG_REV_ID: | 
|  | DPRINTF("Write Revision ID: 0x%x\n", (unsigned) val); /* No effect */ | 
|  | break; | 
|  |  | 
|  | case REG_IP_A_CTRL: | 
|  | case REG_IP_B_CTRL: | 
|  | case REG_IP_C_CTRL: | 
|  | case REG_IP_D_CTRL: | 
|  | { | 
|  | unsigned ip_n = IP_N_FROM_REG(addr); | 
|  | s->ctrl[ip_n] = val; | 
|  | DPRINTF("Write IP %c CONTROL: 0x%x\n", 'A' + ip_n, (unsigned) val); | 
|  | } | 
|  | break; | 
|  |  | 
|  | case REG_RESET: | 
|  | DPRINTF("Write RESET: 0x%x\n", (unsigned) val); /* Not implemented */ | 
|  | break; | 
|  |  | 
|  | case REG_STATUS: | 
|  | { | 
|  | unsigned i; | 
|  |  | 
|  | for (i = 0; i < N_MODULES; i++) { | 
|  | IPackDevice *ip = ipack_device_find(&s->bus, i); | 
|  |  | 
|  | if (ip != NULL) { | 
|  | if (val & STATUS_INT(i, 0)) { | 
|  | DPRINTF("Clear IP %c INT0# status\n", 'A' + i); | 
|  | qemu_irq_lower(ip->irq[0]); | 
|  | } | 
|  | if (val & STATUS_INT(i, 1)) { | 
|  | DPRINTF("Clear IP %c INT1# status\n", 'A' + i); | 
|  | qemu_irq_lower(ip->irq[1]); | 
|  | } | 
|  | } | 
|  |  | 
|  | if (val & STATUS_TIME(i)) { | 
|  | DPRINTF("Clear IP %c timeout\n", 'A' + i); | 
|  | s->status &= ~STATUS_TIME(i); | 
|  | } | 
|  | } | 
|  |  | 
|  | if (val & STATUS_ERR_ANY) { | 
|  | DPRINTF("Unexpected write to STATUS register: 0x%x\n", | 
|  | (unsigned) val); | 
|  | } | 
|  | } | 
|  | break; | 
|  |  | 
|  | /* Reserved */ | 
|  | default: | 
|  | DPRINTF("Unsupported write to LAS0 0x%x: 0x%x\n", | 
|  | (unsigned) addr, (unsigned) val); | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | static uint64_t tpci200_read_las1(void *opaque, hwaddr addr, unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | IPackDevice *ip; | 
|  | uint64_t ret = 0; | 
|  | unsigned ip_n, space; | 
|  | uint8_t offset; | 
|  |  | 
|  | adjust_addr(s->big_endian[1], &addr, size); | 
|  |  | 
|  | /* | 
|  | * The address is divided into the IP module number (0-4), the IP | 
|  | * address space (I/O, ID, INT) and the offset within that space. | 
|  | */ | 
|  | ip_n = addr >> 8; | 
|  | space = (addr >> 6) & 3; | 
|  | ip = ipack_device_find(&s->bus, ip_n); | 
|  |  | 
|  | if (ip == NULL) { | 
|  | DPRINTF("Read LAS1: IP module %u not installed\n", ip_n); | 
|  | } else { | 
|  | IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); | 
|  | switch (space) { | 
|  |  | 
|  | case IP_ID_SPACE: | 
|  | offset = addr & IP_ID_SPACE_ADDR_MASK; | 
|  | if (k->id_read) { | 
|  | ret = k->id_read(ip, offset); | 
|  | } | 
|  | break; | 
|  |  | 
|  | case IP_INT_SPACE: | 
|  | offset = addr & IP_INT_SPACE_ADDR_MASK; | 
|  |  | 
|  | /* Read address 0 to ACK IP INT0# and address 2 to ACK IP INT1# */ | 
|  | if (offset == 0 || offset == 2) { | 
|  | unsigned intno = offset / 2; | 
|  | bool int_set = s->status & STATUS_INT(ip_n, intno); | 
|  | bool int_edge_sensitive = s->ctrl[ip_n] & CTRL_INT_EDGE(intno); | 
|  | if (int_set && !int_edge_sensitive) { | 
|  | qemu_irq_lower(ip->irq[intno]); | 
|  | } | 
|  | } | 
|  |  | 
|  | if (k->int_read) { | 
|  | ret = k->int_read(ip, offset); | 
|  | } | 
|  | break; | 
|  |  | 
|  | default: | 
|  | offset = addr & IP_IO_SPACE_ADDR_MASK; | 
|  | if (k->io_read) { | 
|  | ret = k->io_read(ip, offset); | 
|  | } | 
|  | break; | 
|  | } | 
|  | } | 
|  |  | 
|  | return adjust_value(s->big_endian[1], &ret, size); | 
|  | } | 
|  |  | 
|  | static void tpci200_write_las1(void *opaque, hwaddr addr, uint64_t val, | 
|  | unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | IPackDevice *ip; | 
|  | unsigned ip_n, space; | 
|  | uint8_t offset; | 
|  |  | 
|  | adjust_addr(s->big_endian[1], &addr, size); | 
|  | adjust_value(s->big_endian[1], &val, size); | 
|  |  | 
|  | /* | 
|  | * The address is divided into the IP module number, the IP | 
|  | * address space (I/O, ID, INT) and the offset within that space. | 
|  | */ | 
|  | ip_n = addr >> 8; | 
|  | space = (addr >> 6) & 3; | 
|  | ip = ipack_device_find(&s->bus, ip_n); | 
|  |  | 
|  | if (ip == NULL) { | 
|  | DPRINTF("Write LAS1: IP module %u not installed\n", ip_n); | 
|  | } else { | 
|  | IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); | 
|  | switch (space) { | 
|  |  | 
|  | case IP_ID_SPACE: | 
|  | offset = addr & IP_ID_SPACE_ADDR_MASK; | 
|  | if (k->id_write) { | 
|  | k->id_write(ip, offset, val); | 
|  | } | 
|  | break; | 
|  |  | 
|  | case IP_INT_SPACE: | 
|  | offset = addr & IP_INT_SPACE_ADDR_MASK; | 
|  | if (k->int_write) { | 
|  | k->int_write(ip, offset, val); | 
|  | } | 
|  | break; | 
|  |  | 
|  | default: | 
|  | offset = addr & IP_IO_SPACE_ADDR_MASK; | 
|  | if (k->io_write) { | 
|  | k->io_write(ip, offset, val); | 
|  | } | 
|  | break; | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static uint64_t tpci200_read_las2(void *opaque, hwaddr addr, unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | IPackDevice *ip; | 
|  | uint64_t ret = 0; | 
|  | unsigned ip_n; | 
|  | uint32_t offset; | 
|  |  | 
|  | adjust_addr(s->big_endian[2], &addr, size); | 
|  |  | 
|  | /* | 
|  | * The address is divided into the IP module number and the offset | 
|  | * within the IP module MEM space. | 
|  | */ | 
|  | ip_n = addr >> 23; | 
|  | offset = addr & 0x7fffff; | 
|  | ip = ipack_device_find(&s->bus, ip_n); | 
|  |  | 
|  | if (ip == NULL) { | 
|  | DPRINTF("Read LAS2: IP module %u not installed\n", ip_n); | 
|  | } else { | 
|  | IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); | 
|  | if (k->mem_read16) { | 
|  | ret = k->mem_read16(ip, offset); | 
|  | } | 
|  | } | 
|  |  | 
|  | return adjust_value(s->big_endian[2], &ret, size); | 
|  | } | 
|  |  | 
|  | static void tpci200_write_las2(void *opaque, hwaddr addr, uint64_t val, | 
|  | unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | IPackDevice *ip; | 
|  | unsigned ip_n; | 
|  | uint32_t offset; | 
|  |  | 
|  | adjust_addr(s->big_endian[2], &addr, size); | 
|  | adjust_value(s->big_endian[2], &val, size); | 
|  |  | 
|  | /* | 
|  | * The address is divided into the IP module number and the offset | 
|  | * within the IP module MEM space. | 
|  | */ | 
|  | ip_n = addr >> 23; | 
|  | offset = addr & 0x7fffff; | 
|  | ip = ipack_device_find(&s->bus, ip_n); | 
|  |  | 
|  | if (ip == NULL) { | 
|  | DPRINTF("Write LAS2: IP module %u not installed\n", ip_n); | 
|  | } else { | 
|  | IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); | 
|  | if (k->mem_write16) { | 
|  | k->mem_write16(ip, offset, val); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static uint64_t tpci200_read_las3(void *opaque, hwaddr addr, unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | IPackDevice *ip; | 
|  | uint64_t ret = 0; | 
|  | /* | 
|  | * The address is divided into the IP module number and the offset | 
|  | * within the IP module MEM space. | 
|  | */ | 
|  | unsigned ip_n = addr >> 22; | 
|  | uint32_t offset = addr & 0x3fffff; | 
|  |  | 
|  | ip = ipack_device_find(&s->bus, ip_n); | 
|  |  | 
|  | if (ip == NULL) { | 
|  | DPRINTF("Read LAS3: IP module %u not installed\n", ip_n); | 
|  | } else { | 
|  | IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); | 
|  | if (k->mem_read8) { | 
|  | ret = k->mem_read8(ip, offset); | 
|  | } | 
|  | } | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static void tpci200_write_las3(void *opaque, hwaddr addr, uint64_t val, | 
|  | unsigned size) | 
|  | { | 
|  | TPCI200State *s = opaque; | 
|  | IPackDevice *ip; | 
|  | /* | 
|  | * The address is divided into the IP module number and the offset | 
|  | * within the IP module MEM space. | 
|  | */ | 
|  | unsigned ip_n = addr >> 22; | 
|  | uint32_t offset = addr & 0x3fffff; | 
|  |  | 
|  | ip = ipack_device_find(&s->bus, ip_n); | 
|  |  | 
|  | if (ip == NULL) { | 
|  | DPRINTF("Write LAS3: IP module %u not installed\n", ip_n); | 
|  | } else { | 
|  | IPackDeviceClass *k = IPACK_DEVICE_GET_CLASS(ip); | 
|  | if (k->mem_write8) { | 
|  | k->mem_write8(ip, offset, val); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static const MemoryRegionOps tpci200_cfg_ops = { | 
|  | .read = tpci200_read_cfg, | 
|  | .write = tpci200_write_cfg, | 
|  | .endianness = DEVICE_NATIVE_ENDIAN, | 
|  | .valid =  { | 
|  | .min_access_size = 1, | 
|  | .max_access_size = 4 | 
|  | }, | 
|  | .impl = { | 
|  | .min_access_size = 1, | 
|  | .max_access_size = 1 | 
|  | } | 
|  | }; | 
|  |  | 
|  | static const MemoryRegionOps tpci200_las0_ops = { | 
|  | .read = tpci200_read_las0, | 
|  | .write = tpci200_write_las0, | 
|  | .endianness = DEVICE_NATIVE_ENDIAN, | 
|  | .valid =  { | 
|  | .min_access_size = 2, | 
|  | .max_access_size = 2 | 
|  | } | 
|  | }; | 
|  |  | 
|  | static const MemoryRegionOps tpci200_las1_ops = { | 
|  | .read = tpci200_read_las1, | 
|  | .write = tpci200_write_las1, | 
|  | .endianness = DEVICE_NATIVE_ENDIAN, | 
|  | .valid =  { | 
|  | .min_access_size = 1, | 
|  | .max_access_size = 2 | 
|  | } | 
|  | }; | 
|  |  | 
|  | static const MemoryRegionOps tpci200_las2_ops = { | 
|  | .read = tpci200_read_las2, | 
|  | .write = tpci200_write_las2, | 
|  | .endianness = DEVICE_NATIVE_ENDIAN, | 
|  | .valid =  { | 
|  | .min_access_size = 1, | 
|  | .max_access_size = 2 | 
|  | } | 
|  | }; | 
|  |  | 
|  | static const MemoryRegionOps tpci200_las3_ops = { | 
|  | .read = tpci200_read_las3, | 
|  | .write = tpci200_write_las3, | 
|  | .endianness = DEVICE_NATIVE_ENDIAN, | 
|  | .valid =  { | 
|  | .min_access_size = 1, | 
|  | .max_access_size = 1 | 
|  | } | 
|  | }; | 
|  |  | 
|  | static void tpci200_realize(PCIDevice *pci_dev, Error **errp) | 
|  | { | 
|  | TPCI200State *s = TPCI200(pci_dev); | 
|  | uint8_t *c = s->dev.config; | 
|  |  | 
|  | pci_set_word(c + PCI_COMMAND, 0x0003); | 
|  | pci_set_word(c + PCI_STATUS,  0x0280); | 
|  |  | 
|  | pci_set_byte(c + PCI_INTERRUPT_PIN, 0x01); /* Interrupt pin A */ | 
|  |  | 
|  | pci_set_byte(c + PCI_CAPABILITY_LIST, 0x40); | 
|  | pci_set_long(c + 0x40, 0x48014801); | 
|  | pci_set_long(c + 0x48, 0x00024C06); | 
|  | pci_set_long(c + 0x4C, 0x00000003); | 
|  |  | 
|  | memory_region_init_io(&s->mmio, OBJECT(s), &tpci200_cfg_ops, | 
|  | s, "tpci200_mmio", 128); | 
|  | memory_region_init_io(&s->io, OBJECT(s),   &tpci200_cfg_ops, | 
|  | s, "tpci200_io",   128); | 
|  | memory_region_init_io(&s->las0, OBJECT(s), &tpci200_las0_ops, | 
|  | s, "tpci200_las0", 256); | 
|  | memory_region_init_io(&s->las1, OBJECT(s), &tpci200_las1_ops, | 
|  | s, "tpci200_las1", 1024); | 
|  | memory_region_init_io(&s->las2, OBJECT(s), &tpci200_las2_ops, | 
|  | s, "tpci200_las2", 32 * MiB); | 
|  | memory_region_init_io(&s->las3, OBJECT(s), &tpci200_las3_ops, | 
|  | s, "tpci200_las3", 16 * MiB); | 
|  | pci_register_bar(&s->dev, 0, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->mmio); | 
|  | pci_register_bar(&s->dev, 1, PCI_BASE_ADDRESS_SPACE_IO,     &s->io); | 
|  | pci_register_bar(&s->dev, 2, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las0); | 
|  | pci_register_bar(&s->dev, 3, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las1); | 
|  | pci_register_bar(&s->dev, 4, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las2); | 
|  | pci_register_bar(&s->dev, 5, PCI_BASE_ADDRESS_SPACE_MEMORY, &s->las3); | 
|  |  | 
|  | ipack_bus_init(&s->bus, sizeof(s->bus), DEVICE(pci_dev), | 
|  | N_MODULES, tpci200_set_irq); | 
|  | } | 
|  |  | 
|  | static const VMStateDescription vmstate_tpci200 = { | 
|  | .name = "tpci200", | 
|  | .version_id = 1, | 
|  | .minimum_version_id = 1, | 
|  | .fields = (const VMStateField[]) { | 
|  | VMSTATE_PCI_DEVICE(dev, TPCI200State), | 
|  | VMSTATE_BOOL_ARRAY(big_endian, TPCI200State, 3), | 
|  | VMSTATE_UINT8_ARRAY(ctrl, TPCI200State, N_MODULES), | 
|  | VMSTATE_UINT16(status, TPCI200State), | 
|  | VMSTATE_UINT8(int_set, TPCI200State), | 
|  | VMSTATE_END_OF_LIST() | 
|  | } | 
|  | }; | 
|  |  | 
|  | static void tpci200_class_init(ObjectClass *klass, void *data) | 
|  | { | 
|  | DeviceClass *dc = DEVICE_CLASS(klass); | 
|  | PCIDeviceClass *k = PCI_DEVICE_CLASS(klass); | 
|  |  | 
|  | k->realize = tpci200_realize; | 
|  | k->vendor_id = PCI_VENDOR_ID_TEWS; | 
|  | k->device_id = PCI_DEVICE_ID_TEWS_TPCI200; | 
|  | k->class_id = PCI_CLASS_BRIDGE_OTHER; | 
|  | k->subsystem_vendor_id = PCI_VENDOR_ID_TEWS; | 
|  | k->subsystem_id = 0x300A; | 
|  | set_bit(DEVICE_CATEGORY_INPUT, dc->categories); | 
|  | dc->desc = "TEWS TPCI200 IndustryPack carrier"; | 
|  | dc->vmsd = &vmstate_tpci200; | 
|  | } | 
|  |  | 
|  | static const TypeInfo tpci200_info = { | 
|  | .name          = TYPE_TPCI200, | 
|  | .parent        = TYPE_PCI_DEVICE, | 
|  | .instance_size = sizeof(TPCI200State), | 
|  | .class_init    = tpci200_class_init, | 
|  | .interfaces = (InterfaceInfo[]) { | 
|  | { INTERFACE_CONVENTIONAL_PCI_DEVICE }, | 
|  | { }, | 
|  | }, | 
|  | }; | 
|  |  | 
|  | static void tpci200_register_types(void) | 
|  | { | 
|  | type_register_static(&tpci200_info); | 
|  | } | 
|  |  | 
|  | type_init(tpci200_register_types) |