| /* |
| * Intel XScale PXA255/270 GPIO controller emulation. |
| * |
| * Copyright (c) 2006 Openedhand Ltd. |
| * Written by Andrzej Zaborowski <balrog@zabor.org> |
| * |
| * This code is licensed under the GPL. |
| */ |
| |
| #include "qemu/osdep.h" |
| #include "cpu.h" |
| #include "hw/hw.h" |
| #include "hw/irq.h" |
| #include "hw/qdev-properties.h" |
| #include "hw/sysbus.h" |
| #include "migration/vmstate.h" |
| #include "hw/arm/pxa.h" |
| #include "qemu/log.h" |
| #include "qemu/module.h" |
| |
| #define PXA2XX_GPIO_BANKS 4 |
| |
| #define TYPE_PXA2XX_GPIO "pxa2xx-gpio" |
| #define PXA2XX_GPIO(obj) \ |
| OBJECT_CHECK(PXA2xxGPIOInfo, (obj), TYPE_PXA2XX_GPIO) |
| |
| typedef struct PXA2xxGPIOInfo PXA2xxGPIOInfo; |
| struct PXA2xxGPIOInfo { |
| /*< private >*/ |
| SysBusDevice parent_obj; |
| /*< public >*/ |
| |
| MemoryRegion iomem; |
| qemu_irq irq0, irq1, irqX; |
| int lines; |
| int ncpu; |
| ARMCPU *cpu; |
| |
| /* XXX: GNU C vectors are more suitable */ |
| uint32_t ilevel[PXA2XX_GPIO_BANKS]; |
| uint32_t olevel[PXA2XX_GPIO_BANKS]; |
| uint32_t dir[PXA2XX_GPIO_BANKS]; |
| uint32_t rising[PXA2XX_GPIO_BANKS]; |
| uint32_t falling[PXA2XX_GPIO_BANKS]; |
| uint32_t status[PXA2XX_GPIO_BANKS]; |
| uint32_t gafr[PXA2XX_GPIO_BANKS * 2]; |
| |
| uint32_t prev_level[PXA2XX_GPIO_BANKS]; |
| qemu_irq handler[PXA2XX_GPIO_BANKS * 32]; |
| qemu_irq read_notify; |
| }; |
| |
| static struct { |
| enum { |
| GPIO_NONE, |
| GPLR, |
| GPSR, |
| GPCR, |
| GPDR, |
| GRER, |
| GFER, |
| GEDR, |
| GAFR_L, |
| GAFR_U, |
| } reg; |
| int bank; |
| } pxa2xx_gpio_regs[0x200] = { |
| [0 ... 0x1ff] = { GPIO_NONE, 0 }, |
| #define PXA2XX_REG(reg, a0, a1, a2, a3) \ |
| [a0] = { reg, 0 }, [a1] = { reg, 1 }, [a2] = { reg, 2 }, [a3] = { reg, 3 }, |
| |
| PXA2XX_REG(GPLR, 0x000, 0x004, 0x008, 0x100) |
| PXA2XX_REG(GPSR, 0x018, 0x01c, 0x020, 0x118) |
| PXA2XX_REG(GPCR, 0x024, 0x028, 0x02c, 0x124) |
| PXA2XX_REG(GPDR, 0x00c, 0x010, 0x014, 0x10c) |
| PXA2XX_REG(GRER, 0x030, 0x034, 0x038, 0x130) |
| PXA2XX_REG(GFER, 0x03c, 0x040, 0x044, 0x13c) |
| PXA2XX_REG(GEDR, 0x048, 0x04c, 0x050, 0x148) |
| PXA2XX_REG(GAFR_L, 0x054, 0x05c, 0x064, 0x06c) |
| PXA2XX_REG(GAFR_U, 0x058, 0x060, 0x068, 0x070) |
| }; |
| |
| static void pxa2xx_gpio_irq_update(PXA2xxGPIOInfo *s) |
| { |
| if (s->status[0] & (1 << 0)) |
| qemu_irq_raise(s->irq0); |
| else |
| qemu_irq_lower(s->irq0); |
| |
| if (s->status[0] & (1 << 1)) |
| qemu_irq_raise(s->irq1); |
| else |
| qemu_irq_lower(s->irq1); |
| |
| if ((s->status[0] & ~3) | s->status[1] | s->status[2] | s->status[3]) |
| qemu_irq_raise(s->irqX); |
| else |
| qemu_irq_lower(s->irqX); |
| } |
| |
| /* Bitmap of pins used as standby and sleep wake-up sources. */ |
| static const int pxa2xx_gpio_wake[PXA2XX_GPIO_BANKS] = { |
| 0x8003fe1b, 0x002001fc, 0xec080000, 0x0012007f, |
| }; |
| |
| static void pxa2xx_gpio_set(void *opaque, int line, int level) |
| { |
| PXA2xxGPIOInfo *s = (PXA2xxGPIOInfo *) opaque; |
| CPUState *cpu = CPU(s->cpu); |
| int bank; |
| uint32_t mask; |
| |
| if (line >= s->lines) { |
| printf("%s: No GPIO pin %i\n", __func__, line); |
| return; |
| } |
| |
| bank = line >> 5; |
| mask = 1U << (line & 31); |
| |
| if (level) { |
| s->status[bank] |= s->rising[bank] & mask & |
| ~s->ilevel[bank] & ~s->dir[bank]; |
| s->ilevel[bank] |= mask; |
| } else { |
| s->status[bank] |= s->falling[bank] & mask & |
| s->ilevel[bank] & ~s->dir[bank]; |
| s->ilevel[bank] &= ~mask; |
| } |
| |
| if (s->status[bank] & mask) |
| pxa2xx_gpio_irq_update(s); |
| |
| /* Wake-up GPIOs */ |
| if (cpu->halted && (mask & ~s->dir[bank] & pxa2xx_gpio_wake[bank])) { |
| cpu_interrupt(cpu, CPU_INTERRUPT_EXITTB); |
| } |
| } |
| |
| static void pxa2xx_gpio_handler_update(PXA2xxGPIOInfo *s) { |
| uint32_t level, diff; |
| int i, bit, line; |
| for (i = 0; i < PXA2XX_GPIO_BANKS; i ++) { |
| level = s->olevel[i] & s->dir[i]; |
| |
| for (diff = s->prev_level[i] ^ level; diff; diff ^= 1 << bit) { |
| bit = ctz32(diff); |
| line = bit + 32 * i; |
| qemu_set_irq(s->handler[line], (level >> bit) & 1); |
| } |
| |
| s->prev_level[i] = level; |
| } |
| } |
| |
| static uint64_t pxa2xx_gpio_read(void *opaque, hwaddr offset, |
| unsigned size) |
| { |
| PXA2xxGPIOInfo *s = (PXA2xxGPIOInfo *) opaque; |
| uint32_t ret; |
| int bank; |
| if (offset >= 0x200) |
| return 0; |
| |
| bank = pxa2xx_gpio_regs[offset].bank; |
| switch (pxa2xx_gpio_regs[offset].reg) { |
| case GPDR: /* GPIO Pin-Direction registers */ |
| return s->dir[bank]; |
| |
| case GPSR: /* GPIO Pin-Output Set registers */ |
| qemu_log_mask(LOG_GUEST_ERROR, |
| "pxa2xx GPIO: read from write only register GPSR\n"); |
| return 0; |
| |
| case GPCR: /* GPIO Pin-Output Clear registers */ |
| qemu_log_mask(LOG_GUEST_ERROR, |
| "pxa2xx GPIO: read from write only register GPCR\n"); |
| return 0; |
| |
| case GRER: /* GPIO Rising-Edge Detect Enable registers */ |
| return s->rising[bank]; |
| |
| case GFER: /* GPIO Falling-Edge Detect Enable registers */ |
| return s->falling[bank]; |
| |
| case GAFR_L: /* GPIO Alternate Function registers */ |
| return s->gafr[bank * 2]; |
| |
| case GAFR_U: /* GPIO Alternate Function registers */ |
| return s->gafr[bank * 2 + 1]; |
| |
| case GPLR: /* GPIO Pin-Level registers */ |
| ret = (s->olevel[bank] & s->dir[bank]) | |
| (s->ilevel[bank] & ~s->dir[bank]); |
| qemu_irq_raise(s->read_notify); |
| return ret; |
| |
| case GEDR: /* GPIO Edge Detect Status registers */ |
| return s->status[bank]; |
| |
| default: |
| hw_error("%s: Bad offset " REG_FMT "\n", __func__, offset); |
| } |
| |
| return 0; |
| } |
| |
| static void pxa2xx_gpio_write(void *opaque, hwaddr offset, |
| uint64_t value, unsigned size) |
| { |
| PXA2xxGPIOInfo *s = (PXA2xxGPIOInfo *) opaque; |
| int bank; |
| if (offset >= 0x200) |
| return; |
| |
| bank = pxa2xx_gpio_regs[offset].bank; |
| switch (pxa2xx_gpio_regs[offset].reg) { |
| case GPDR: /* GPIO Pin-Direction registers */ |
| s->dir[bank] = value; |
| pxa2xx_gpio_handler_update(s); |
| break; |
| |
| case GPSR: /* GPIO Pin-Output Set registers */ |
| s->olevel[bank] |= value; |
| pxa2xx_gpio_handler_update(s); |
| break; |
| |
| case GPCR: /* GPIO Pin-Output Clear registers */ |
| s->olevel[bank] &= ~value; |
| pxa2xx_gpio_handler_update(s); |
| break; |
| |
| case GRER: /* GPIO Rising-Edge Detect Enable registers */ |
| s->rising[bank] = value; |
| break; |
| |
| case GFER: /* GPIO Falling-Edge Detect Enable registers */ |
| s->falling[bank] = value; |
| break; |
| |
| case GAFR_L: /* GPIO Alternate Function registers */ |
| s->gafr[bank * 2] = value; |
| break; |
| |
| case GAFR_U: /* GPIO Alternate Function registers */ |
| s->gafr[bank * 2 + 1] = value; |
| break; |
| |
| case GEDR: /* GPIO Edge Detect Status registers */ |
| s->status[bank] &= ~value; |
| pxa2xx_gpio_irq_update(s); |
| break; |
| |
| default: |
| hw_error("%s: Bad offset " REG_FMT "\n", __func__, offset); |
| } |
| } |
| |
| static const MemoryRegionOps pxa_gpio_ops = { |
| .read = pxa2xx_gpio_read, |
| .write = pxa2xx_gpio_write, |
| .endianness = DEVICE_NATIVE_ENDIAN, |
| }; |
| |
| DeviceState *pxa2xx_gpio_init(hwaddr base, |
| ARMCPU *cpu, DeviceState *pic, int lines) |
| { |
| CPUState *cs = CPU(cpu); |
| DeviceState *dev; |
| |
| dev = qdev_create(NULL, TYPE_PXA2XX_GPIO); |
| qdev_prop_set_int32(dev, "lines", lines); |
| qdev_prop_set_int32(dev, "ncpu", cs->cpu_index); |
| qdev_init_nofail(dev); |
| |
| sysbus_mmio_map(SYS_BUS_DEVICE(dev), 0, base); |
| sysbus_connect_irq(SYS_BUS_DEVICE(dev), 0, |
| qdev_get_gpio_in(pic, PXA2XX_PIC_GPIO_0)); |
| sysbus_connect_irq(SYS_BUS_DEVICE(dev), 1, |
| qdev_get_gpio_in(pic, PXA2XX_PIC_GPIO_1)); |
| sysbus_connect_irq(SYS_BUS_DEVICE(dev), 2, |
| qdev_get_gpio_in(pic, PXA2XX_PIC_GPIO_X)); |
| |
| return dev; |
| } |
| |
| static void pxa2xx_gpio_initfn(Object *obj) |
| { |
| SysBusDevice *sbd = SYS_BUS_DEVICE(obj); |
| DeviceState *dev = DEVICE(sbd); |
| PXA2xxGPIOInfo *s = PXA2XX_GPIO(dev); |
| |
| memory_region_init_io(&s->iomem, obj, &pxa_gpio_ops, |
| s, "pxa2xx-gpio", 0x1000); |
| sysbus_init_mmio(sbd, &s->iomem); |
| sysbus_init_irq(sbd, &s->irq0); |
| sysbus_init_irq(sbd, &s->irq1); |
| sysbus_init_irq(sbd, &s->irqX); |
| } |
| |
| static void pxa2xx_gpio_realize(DeviceState *dev, Error **errp) |
| { |
| PXA2xxGPIOInfo *s = PXA2XX_GPIO(dev); |
| |
| s->cpu = ARM_CPU(qemu_get_cpu(s->ncpu)); |
| |
| qdev_init_gpio_in(dev, pxa2xx_gpio_set, s->lines); |
| qdev_init_gpio_out(dev, s->handler, s->lines); |
| } |
| |
| /* |
| * Registers a callback to notify on GPLR reads. This normally |
| * shouldn't be needed but it is used for the hack on Spitz machines. |
| */ |
| void pxa2xx_gpio_read_notifier(DeviceState *dev, qemu_irq handler) |
| { |
| PXA2xxGPIOInfo *s = PXA2XX_GPIO(dev); |
| |
| s->read_notify = handler; |
| } |
| |
| static const VMStateDescription vmstate_pxa2xx_gpio_regs = { |
| .name = "pxa2xx-gpio", |
| .version_id = 1, |
| .minimum_version_id = 1, |
| .fields = (VMStateField[]) { |
| VMSTATE_UINT32_ARRAY(ilevel, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS), |
| VMSTATE_UINT32_ARRAY(olevel, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS), |
| VMSTATE_UINT32_ARRAY(dir, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS), |
| VMSTATE_UINT32_ARRAY(rising, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS), |
| VMSTATE_UINT32_ARRAY(falling, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS), |
| VMSTATE_UINT32_ARRAY(status, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS), |
| VMSTATE_UINT32_ARRAY(gafr, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS * 2), |
| VMSTATE_UINT32_ARRAY(prev_level, PXA2xxGPIOInfo, PXA2XX_GPIO_BANKS), |
| VMSTATE_END_OF_LIST(), |
| }, |
| }; |
| |
| static Property pxa2xx_gpio_properties[] = { |
| DEFINE_PROP_INT32("lines", PXA2xxGPIOInfo, lines, 0), |
| DEFINE_PROP_INT32("ncpu", PXA2xxGPIOInfo, ncpu, 0), |
| DEFINE_PROP_END_OF_LIST(), |
| }; |
| |
| static void pxa2xx_gpio_class_init(ObjectClass *klass, void *data) |
| { |
| DeviceClass *dc = DEVICE_CLASS(klass); |
| |
| dc->desc = "PXA2xx GPIO controller"; |
| device_class_set_props(dc, pxa2xx_gpio_properties); |
| dc->vmsd = &vmstate_pxa2xx_gpio_regs; |
| dc->realize = pxa2xx_gpio_realize; |
| } |
| |
| static const TypeInfo pxa2xx_gpio_info = { |
| .name = TYPE_PXA2XX_GPIO, |
| .parent = TYPE_SYS_BUS_DEVICE, |
| .instance_size = sizeof(PXA2xxGPIOInfo), |
| .instance_init = pxa2xx_gpio_initfn, |
| .class_init = pxa2xx_gpio_class_init, |
| }; |
| |
| static void pxa2xx_gpio_register_types(void) |
| { |
| type_register_static(&pxa2xx_gpio_info); |
| } |
| |
| type_init(pxa2xx_gpio_register_types) |