hw/arm_timer.c - qemu - Git at Google

 /*
  * ARM PrimeCell Timer modules.
  *
  * Copyright (c) 2005-2006 CodeSourcery.
  * Written by Paul Brook
  *
  * This code is licenced under the GPL.
  */

 #include "hw.h"
 #include "qemu-timer.h"
 #include "primecell.h"

 /* Common timer implementation.  */

 #define TIMER_CTRL_ONESHOT      (1 << 0)
 #define TIMER_CTRL_32BIT        (1 << 1)
 #define TIMER_CTRL_DIV1         (0 << 2)
 #define TIMER_CTRL_DIV16        (1 << 2)
 #define TIMER_CTRL_DIV256       (2 << 2)
 #define TIMER_CTRL_IE           (1 << 5)
 #define TIMER_CTRL_PERIODIC     (1 << 6)
 #define TIMER_CTRL_ENABLE       (1 << 7)

 typedef struct {
     ptimer_state *timer;
     uint32_t control;
     uint32_t limit;
     int freq;
     int int_level;
     qemu_irq irq;
 } arm_timer_state;

 /* Check all active timers, and schedule the next timer interrupt.  */

 static void arm_timer_update(arm_timer_state *s)
 {
     /* Update interrupts.  */
     if (s->int_level && (s->control & TIMER_CTRL_IE)) {
         qemu_irq_raise(s->irq);
     } else {
         qemu_irq_lower(s->irq);
     }
 }

 static uint32_t arm_timer_read(void *opaque, target_phys_addr_t offset)
 {
     arm_timer_state *s = (arm_timer_state *)opaque;

     switch (offset >> 2) {
     case 0: /* TimerLoad */
     case 6: /* TimerBGLoad */
         return s->limit;
     case 1: /* TimerValue */
         return ptimer_get_count(s->timer);
     case 2: /* TimerControl */
         return s->control;
     case 4: /* TimerRIS */
         return s->int_level;
     case 5: /* TimerMIS */
         if ((s->control & TIMER_CTRL_IE) == 0)
             return 0;
         return s->int_level;
     default:
         hw_error("arm_timer_read: Bad offset %x\n", (int)offset);
         return 0;
     }
 }

 /* Reset the timer limit after settings have changed.  */
 static void arm_timer_recalibrate(arm_timer_state *s, int reload)
 {
     uint32_t limit;

     if ((s->control & TIMER_CTRL_PERIODIC) == 0) {
         /* Free running.  */
         if (s->control & TIMER_CTRL_32BIT)
             limit = 0xffffffff;
         else
             limit = 0xffff;
     } else {
           /* Periodic.  */
           limit = s->limit;
     }
     ptimer_set_limit(s->timer, limit, reload);
 }

 static void arm_timer_write(void *opaque, target_phys_addr_t offset,
                             uint32_t value)
 {
     arm_timer_state *s = (arm_timer_state *)opaque;
     int freq;

     switch (offset >> 2) {
     case 0: /* TimerLoad */
         s->limit = value;
         arm_timer_recalibrate(s, 1);
         break;
     case 1: /* TimerValue */
         /* ??? Linux seems to want to write to this readonly register.
            Ignore it.  */
         break;
     case 2: /* TimerControl */
         if (s->control & TIMER_CTRL_ENABLE) {
             /* Pause the timer if it is running.  This may cause some
                inaccuracy dure to rounding, but avoids a whole lot of other
                messyness.  */
             ptimer_stop(s->timer);
         }
         s->control = value;
         freq = s->freq;
         /* ??? Need to recalculate expiry time after changing divisor.  */
         switch ((value >> 2) & 3) {
         case 1: freq >>= 4; break;
         case 2: freq >>= 8; break;
         }
         arm_timer_recalibrate(s, 0);
         ptimer_set_freq(s->timer, freq);
         if (s->control & TIMER_CTRL_ENABLE) {
             /* Restart the timer if still enabled.  */
             ptimer_run(s->timer, (s->control & TIMER_CTRL_ONESHOT) != 0);
         }
         break;
     case 3: /* TimerIntClr */
         s->int_level = 0;
         break;
     case 6: /* TimerBGLoad */
         s->limit = value;
         arm_timer_recalibrate(s, 0);
         break;
     default:
         hw_error("arm_timer_write: Bad offset %x\n", (int)offset);
     }
     arm_timer_update(s);
 }

 static void arm_timer_tick(void *opaque)
 {
     arm_timer_state *s = (arm_timer_state *)opaque;
     s->int_level = 1;
     arm_timer_update(s);
 }

 static void arm_timer_save(QEMUFile *f, void *opaque)
 {
     arm_timer_state *s = (arm_timer_state *)opaque;
     qemu_put_be32(f, s->control);
     qemu_put_be32(f, s->limit);
     qemu_put_be32(f, s->int_level);
     qemu_put_ptimer(f, s->timer);
 }

 static int arm_timer_load(QEMUFile *f, void *opaque, int version_id)
 {
     arm_timer_state *s = (arm_timer_state *)opaque;

     if (version_id != 1)
         return -EINVAL;

     s->control = qemu_get_be32(f);
     s->limit = qemu_get_be32(f);
     s->int_level = qemu_get_be32(f);
     qemu_get_ptimer(f, s->timer);
     return 0;
 }

 static void *arm_timer_init(uint32_t freq, qemu_irq irq)
 {
     arm_timer_state *s;
     QEMUBH *bh;

     s = (arm_timer_state *)qemu_mallocz(sizeof(arm_timer_state));
     s->irq = irq;
     s->freq = freq;
     s->control = TIMER_CTRL_IE;

     bh = qemu_bh_new(arm_timer_tick, s);
     s->timer = ptimer_init(bh);
     register_savevm("arm_timer", -1, 1, arm_timer_save, arm_timer_load, s);
     return s;
 }

 /* ARM PrimeCell SP804 dual timer module.
    Docs for this device don't seem to be publicly available.  This
    implementation is based on guesswork, the linux kernel sources and the
    Integrator/CP timer modules.  */

 typedef struct {
     void *timer[2];
     int level[2];
     qemu_irq irq;
 } sp804_state;

 /* Merge the IRQs from the two component devices.  */
 static void sp804_set_irq(void *opaque, int irq, int level)
 {
     sp804_state *s = (sp804_state *)opaque;

     s->level[irq] = level;
     qemu_set_irq(s->irq, s->level[0] || s->level[1]);
 }

 static uint32_t sp804_read(void *opaque, target_phys_addr_t offset)
 {
     sp804_state *s = (sp804_state *)opaque;

     /* ??? Don't know the PrimeCell ID for this device.  */
     if (offset < 0x20) {
         return arm_timer_read(s->timer[0], offset);
     } else {
         return arm_timer_read(s->timer[1], offset - 0x20);
     }
 }

 static void sp804_write(void *opaque, target_phys_addr_t offset,
                         uint32_t value)
 {
     sp804_state *s = (sp804_state *)opaque;

     if (offset < 0x20) {
         arm_timer_write(s->timer[0], offset, value);
     } else {
         arm_timer_write(s->timer[1], offset - 0x20, value);
     }
 }

 static CPUReadMemoryFunc *sp804_readfn[] = {
    sp804_read,
    sp804_read,
    sp804_read
 };

 static CPUWriteMemoryFunc *sp804_writefn[] = {
    sp804_write,
    sp804_write,
    sp804_write
 };

 static void sp804_save(QEMUFile *f, void *opaque)
 {
     sp804_state *s = (sp804_state *)opaque;
     qemu_put_be32(f, s->level[0]);
     qemu_put_be32(f, s->level[1]);
 }

 static int sp804_load(QEMUFile *f, void *opaque, int version_id)
 {
     sp804_state *s = (sp804_state *)opaque;

     if (version_id != 1)
         return -EINVAL;

     s->level[0] = qemu_get_be32(f);
     s->level[1] = qemu_get_be32(f);
     return 0;
 }

 void sp804_init(uint32_t base, qemu_irq irq)
 {
     int iomemtype;
     sp804_state *s;
     qemu_irq *qi;

     s = (sp804_state *)qemu_mallocz(sizeof(sp804_state));
     qi = qemu_allocate_irqs(sp804_set_irq, s, 2);
     s->irq = irq;
     /* ??? The timers are actually configurable between 32kHz and 1MHz, but
        we don't implement that.  */
     s->timer[0] = arm_timer_init(1000000, qi[0]);
     s->timer[1] = arm_timer_init(1000000, qi[1]);
     iomemtype = cpu_register_io_memory(0, sp804_readfn,
                                        sp804_writefn, s);
     cpu_register_physical_memory(base, 0x00001000, iomemtype);
     register_savevm("sp804", -1, 1, sp804_save, sp804_load, s);
 }


 /* Integrator/CP timer module.  */

 typedef struct {
     void *timer[3];
 } icp_pit_state;

 static uint32_t icp_pit_read(void *opaque, target_phys_addr_t offset)
 {
     icp_pit_state *s = (icp_pit_state *)opaque;
     int n;

     /* ??? Don't know the PrimeCell ID for this device.  */
     n = offset >> 8;
     if (n > 3) {
         hw_error("sp804_read: Bad timer %d\n", n);
     }

     return arm_timer_read(s->timer[n], offset & 0xff);
 }

 static void icp_pit_write(void *opaque, target_phys_addr_t offset,
                           uint32_t value)
 {
     icp_pit_state *s = (icp_pit_state *)opaque;
     int n;

     n = offset >> 8;
     if (n > 3) {
         hw_error("sp804_write: Bad timer %d\n", n);
     }

     arm_timer_write(s->timer[n], offset & 0xff, value);
 }


 static CPUReadMemoryFunc *icp_pit_readfn[] = {
    icp_pit_read,
    icp_pit_read,
    icp_pit_read
 };

 static CPUWriteMemoryFunc *icp_pit_writefn[] = {
    icp_pit_write,
    icp_pit_write,
    icp_pit_write
 };

 void icp_pit_init(uint32_t base, qemu_irq *pic, int irq)
 {
     int iomemtype;
     icp_pit_state *s;

     s = (icp_pit_state *)qemu_mallocz(sizeof(icp_pit_state));
     /* Timer 0 runs at the system clock speed (40MHz).  */
     s->timer[0] = arm_timer_init(40000000, pic[irq]);
     /* The other two timers run at 1MHz.  */
     s->timer[1] = arm_timer_init(1000000, pic[irq + 1]);
     s->timer[2] = arm_timer_init(1000000, pic[irq + 2]);

     iomemtype = cpu_register_io_memory(0, icp_pit_readfn,
                                        icp_pit_writefn, s);
     cpu_register_physical_memory(base, 0x00001000, iomemtype);
     /* This device has no state to save/restore.  The component timers will
        save themselves.  */
 }
	/*
	* ARM PrimeCell Timer modules.
	*
	* Copyright (c) 2005-2006 CodeSourcery.
	* Written by Paul Brook
	*
	* This code is licenced under the GPL.
	*/

	#include "hw.h"
	#include "qemu-timer.h"
	#include "primecell.h"

	/* Common timer implementation. */

	#define TIMER_CTRL_ONESHOT (1 << 0)
	#define TIMER_CTRL_32BIT (1 << 1)
	#define TIMER_CTRL_DIV1 (0 << 2)
	#define TIMER_CTRL_DIV16 (1 << 2)
	#define TIMER_CTRL_DIV256 (2 << 2)
	#define TIMER_CTRL_IE (1 << 5)
	#define TIMER_CTRL_PERIODIC (1 << 6)
	#define TIMER_CTRL_ENABLE (1 << 7)

	typedef struct {
	ptimer_state *timer;
	uint32_t control;
	uint32_t limit;
	int freq;
	int int_level;
	qemu_irq irq;
	} arm_timer_state;

	/* Check all active timers, and schedule the next timer interrupt. */

	static void arm_timer_update(arm_timer_state *s)
	{
	/* Update interrupts. */
	if (s->int_level && (s->control & TIMER_CTRL_IE)) {
	qemu_irq_raise(s->irq);
	} else {
	qemu_irq_lower(s->irq);
	}
	}

	static uint32_t arm_timer_read(void *opaque, target_phys_addr_t offset)
	{
	arm_timer_state s = (arm_timer_state )opaque;

	switch (offset >> 2) {
	case 0: /* TimerLoad */
	case 6: /* TimerBGLoad */
	return s->limit;
	case 1: /* TimerValue */
	return ptimer_get_count(s->timer);
	case 2: /* TimerControl */
	return s->control;
	case 4: /* TimerRIS */
	return s->int_level;
	case 5: /* TimerMIS */
	if ((s->control & TIMER_CTRL_IE) == 0)
	return 0;
	return s->int_level;
	default:
	hw_error("arm_timer_read: Bad offset %x\n", (int)offset);
	return 0;
	}
	}

	/* Reset the timer limit after settings have changed. */
	static void arm_timer_recalibrate(arm_timer_state *s, int reload)
	{
	uint32_t limit;

	if ((s->control & TIMER_CTRL_PERIODIC) == 0) {
	/* Free running. */
	if (s->control & TIMER_CTRL_32BIT)
	limit = 0xffffffff;
	else
	limit = 0xffff;
	} else {
	/* Periodic. */
	limit = s->limit;
	}
	ptimer_set_limit(s->timer, limit, reload);
	}

	static void arm_timer_write(void *opaque, target_phys_addr_t offset,
	uint32_t value)
	{
	arm_timer_state s = (arm_timer_state )opaque;
	int freq;

	switch (offset >> 2) {
	case 0: /* TimerLoad */
	s->limit = value;
	arm_timer_recalibrate(s, 1);
	break;
	case 1: /* TimerValue */
	/* ??? Linux seems to want to write to this readonly register.
	Ignore it. */
	break;
	case 2: /* TimerControl */
	if (s->control & TIMER_CTRL_ENABLE) {
	/* Pause the timer if it is running. This may cause some
	inaccuracy dure to rounding, but avoids a whole lot of other
	messyness. */
	ptimer_stop(s->timer);
	}
	s->control = value;
	freq = s->freq;
	/* ??? Need to recalculate expiry time after changing divisor. */
	switch ((value >> 2) & 3) {
	case 1: freq >>= 4; break;
	case 2: freq >>= 8; break;
	}
	arm_timer_recalibrate(s, 0);
	ptimer_set_freq(s->timer, freq);
	if (s->control & TIMER_CTRL_ENABLE) {
	/* Restart the timer if still enabled. */
	ptimer_run(s->timer, (s->control & TIMER_CTRL_ONESHOT) != 0);
	}
	break;
	case 3: /* TimerIntClr */
	s->int_level = 0;
	break;
	case 6: /* TimerBGLoad */
	s->limit = value;
	arm_timer_recalibrate(s, 0);
	break;
	default:
	hw_error("arm_timer_write: Bad offset %x\n", (int)offset);
	}
	arm_timer_update(s);
	}

	static void arm_timer_tick(void *opaque)
	{
	arm_timer_state s = (arm_timer_state )opaque;
	s->int_level = 1;
	arm_timer_update(s);
	}

	static void arm_timer_save(QEMUFile f, void opaque)
	{
	arm_timer_state s = (arm_timer_state )opaque;
	qemu_put_be32(f, s->control);
	qemu_put_be32(f, s->limit);
	qemu_put_be32(f, s->int_level);
	qemu_put_ptimer(f, s->timer);
	}

	static int arm_timer_load(QEMUFile f, void opaque, int version_id)
	{
	arm_timer_state s = (arm_timer_state )opaque;

	if (version_id != 1)
	return -EINVAL;

	s->control = qemu_get_be32(f);
	s->limit = qemu_get_be32(f);
	s->int_level = qemu_get_be32(f);
	qemu_get_ptimer(f, s->timer);
	return 0;
	}

	static void *arm_timer_init(uint32_t freq, qemu_irq irq)
	{
	arm_timer_state *s;
	QEMUBH *bh;

	s = (arm_timer_state *)qemu_mallocz(sizeof(arm_timer_state));
	s->irq = irq;
	s->freq = freq;
	s->control = TIMER_CTRL_IE;

	bh = qemu_bh_new(arm_timer_tick, s);
	s->timer = ptimer_init(bh);
	register_savevm("arm_timer", -1, 1, arm_timer_save, arm_timer_load, s);
	return s;
	}

	/* ARM PrimeCell SP804 dual timer module.
	Docs for this device don't seem to be publicly available. This
	implementation is based on guesswork, the linux kernel sources and the
	Integrator/CP timer modules. */

	typedef struct {
	void *timer[2];
	int level[2];
	qemu_irq irq;
	} sp804_state;

	/* Merge the IRQs from the two component devices. */
	static void sp804_set_irq(void *opaque, int irq, int level)
	{
	sp804_state s = (sp804_state )opaque;

	s->level[irq] = level;
	qemu_set_irq(s->irq, s->level[0] \|\| s->level[1]);
	}

	static uint32_t sp804_read(void *opaque, target_phys_addr_t offset)
	{
	sp804_state s = (sp804_state )opaque;

	/* ??? Don't know the PrimeCell ID for this device. */
	if (offset < 0x20) {
	return arm_timer_read(s->timer[0], offset);
	} else {
	return arm_timer_read(s->timer[1], offset - 0x20);
	}
	}

	static void sp804_write(void *opaque, target_phys_addr_t offset,
	uint32_t value)
	{
	sp804_state s = (sp804_state )opaque;

	if (offset < 0x20) {
	arm_timer_write(s->timer[0], offset, value);
	} else {
	arm_timer_write(s->timer[1], offset - 0x20, value);
	}
	}

	static CPUReadMemoryFunc *sp804_readfn[] = {
	sp804_read,
	sp804_read,
	sp804_read
	};

	static CPUWriteMemoryFunc *sp804_writefn[] = {
	sp804_write,
	sp804_write,
	sp804_write
	};

	static void sp804_save(QEMUFile f, void opaque)
	{
	sp804_state s = (sp804_state )opaque;
	qemu_put_be32(f, s->level[0]);
	qemu_put_be32(f, s->level[1]);
	}

	static int sp804_load(QEMUFile f, void opaque, int version_id)
	{
	sp804_state s = (sp804_state )opaque;

	if (version_id != 1)
	return -EINVAL;

	s->level[0] = qemu_get_be32(f);
	s->level[1] = qemu_get_be32(f);
	return 0;
	}

	void sp804_init(uint32_t base, qemu_irq irq)
	{
	int iomemtype;
	sp804_state *s;
	qemu_irq *qi;

	s = (sp804_state *)qemu_mallocz(sizeof(sp804_state));
	qi = qemu_allocate_irqs(sp804_set_irq, s, 2);
	s->irq = irq;
	/* ??? The timers are actually configurable between 32kHz and 1MHz, but
	we don't implement that. */
	s->timer[0] = arm_timer_init(1000000, qi[0]);
	s->timer[1] = arm_timer_init(1000000, qi[1]);
	iomemtype = cpu_register_io_memory(0, sp804_readfn,
	sp804_writefn, s);
	cpu_register_physical_memory(base, 0x00001000, iomemtype);
	register_savevm("sp804", -1, 1, sp804_save, sp804_load, s);
	}


	/* Integrator/CP timer module. */

	typedef struct {
	void *timer[3];
	} icp_pit_state;

	static uint32_t icp_pit_read(void *opaque, target_phys_addr_t offset)
	{
	icp_pit_state s = (icp_pit_state )opaque;
	int n;

	/* ??? Don't know the PrimeCell ID for this device. */
	n = offset >> 8;
	if (n > 3) {
	hw_error("sp804_read: Bad timer %d\n", n);
	}

	return arm_timer_read(s->timer[n], offset & 0xff);
	}

	static void icp_pit_write(void *opaque, target_phys_addr_t offset,
	uint32_t value)
	{
	icp_pit_state s = (icp_pit_state )opaque;
	int n;

	n = offset >> 8;
	if (n > 3) {
	hw_error("sp804_write: Bad timer %d\n", n);
	}

	arm_timer_write(s->timer[n], offset & 0xff, value);
	}


	static CPUReadMemoryFunc *icp_pit_readfn[] = {
	icp_pit_read,
	icp_pit_read,
	icp_pit_read
	};

	static CPUWriteMemoryFunc *icp_pit_writefn[] = {
	icp_pit_write,
	icp_pit_write,
	icp_pit_write
	};

	void icp_pit_init(uint32_t base, qemu_irq *pic, int irq)
	{
	int iomemtype;
	icp_pit_state *s;

	s = (icp_pit_state *)qemu_mallocz(sizeof(icp_pit_state));
	/* Timer 0 runs at the system clock speed (40MHz). */
	s->timer[0] = arm_timer_init(40000000, pic[irq]);
	/* The other two timers run at 1MHz. */
	s->timer[1] = arm_timer_init(1000000, pic[irq + 1]);
	s->timer[2] = arm_timer_init(1000000, pic[irq + 2]);

	iomemtype = cpu_register_io_memory(0, icp_pit_readfn,
	icp_pit_writefn, s);
	cpu_register_physical_memory(base, 0x00001000, iomemtype);
	/* This device has no state to save/restore. The component timers will
	save themselves. */
	}