| #ifndef CONFIG_DHCP_H | |
| #define CONFIG_DHCP_H | |
| /** @file | |
| * | |
| * DHCP configuration | |
| * | |
| */ | |
| FILE_LICENCE ( GPL2_OR_LATER_OR_UBDL ); | |
| FILE_SECBOOT ( PERMITTED ); | |
| #include <config/defaults.h> | |
| /* | |
| * DHCP and PXE Boot Server timeout parameters | |
| * | |
| * Initial and final timeout for DHCP discovery | |
| * | |
| * The PXE spec indicates discover request are sent 4 times, with | |
| * timeouts of 4, 8, 16, 32 seconds. iPXE by default uses 1, 2, 4, 8. | |
| */ | |
| #define DHCP_DISC_START_TIMEOUT_SEC 1 | |
| #define DHCP_DISC_END_TIMEOUT_SEC 10 | |
| //#define DHCP_DISC_START_TIMEOUT_SEC 4 /* as per PXE spec */ | |
| //#define DHCP_DISC_END_TIMEOUT_SEC 32 /* as per PXE spec */ | |
| /* | |
| * Maximum number of discovery deferrals due to blocked links | |
| * (e.g. from non-forwarding STP ports) | |
| */ | |
| #define DHCP_DISC_MAX_DEFERRALS 180 | |
| /* | |
| * ProxyDHCP offers are given precedence by continue to wait for them | |
| * after a valid DHCPOFFER is received. We'll wait through this | |
| * timeout for it. The PXE spec indicates waiting through the 4 & 8 | |
| * second timeouts, iPXE by default stops after 2. | |
| */ | |
| #define DHCP_DISC_PROXY_TIMEOUT_SEC 2 | |
| //#define DHCP_DISC_PROXY_TIMEOUT_SEC 11 /* as per PXE spec */ | |
| /* | |
| * Per the PXE spec, requests are also tried 4 times, but at timeout | |
| * intervals of 1, 2, 3, 4 seconds. To adapt this to an exponential | |
| * backoff timer, we can either do 1, 2, 4, 8, ie. 4 retires with a | |
| * longer interval or start at 0 (0.25s) for 0.25, 0.5, 1, 2, 4, | |
| * ie. one extra try and shorter initial timeouts. iPXE by default | |
| * does a combination of both, starting at 0 and going through the 8 | |
| * second timeout. | |
| */ | |
| #define DHCP_REQ_START_TIMEOUT_SEC 0 | |
| #define DHCP_REQ_END_TIMEOUT_SEC 10 | |
| //#define DHCP_REQ_END_TIMEOUT_SEC 4 /* as per PXE spec */ | |
| /* | |
| * A ProxyDHCP offer without PXE options also goes through a request | |
| * phase using these same parameters, but note the early break below. | |
| */ | |
| #define DHCP_PROXY_START_TIMEOUT_SEC 0 | |
| #define DHCP_PROXY_END_TIMEOUT_SEC 10 | |
| //#define DHCP_PROXY_END_TIMEOUT_SEC 8 /* as per PXE spec */ | |
| /* | |
| * A ProxyDHCP request timeout should not induce a failure condition, | |
| * so we always want to break before the above set of timers expire. | |
| * The iPXE default value of 2 breaks at the first timeout after 2 | |
| * seconds, which will be after the 2 second timeout. | |
| */ | |
| #define DHCP_REQ_PROXY_TIMEOUT_SEC 2 | |
| //#define DHCP_REQ_PROXY_TIMEOUT_SEC 7 /* as per PXE spec */ | |
| /* | |
| * Per the PXE spec, a PXE boot server request is also be retried 4 | |
| * times at timeouts of 1, 2, 3, 4. iPXE uses the same timeouts as | |
| * discovery, 1, 2, 4, 8, but will move on to the next server if | |
| * available after an elapsed time greater than 3 seconds, therefore | |
| * effectively only sending 3 tries at timeouts of 1, 2, 4. | |
| */ | |
| #define PXEBS_START_TIMEOUT_SEC 1 | |
| #define PXEBS_END_TIMEOUT_SEC 10 | |
| //#define PXEBS_START_TIMEOUT_SEC 0 /* as per PXE spec */ | |
| //#define PXEBS_END_TIMEOUT_SEC 8 /* as per PXE spec */ | |
| /* | |
| * Increment to the next PXE Boot server, if available, after this | |
| * this much time has elapsed. | |
| */ | |
| #define PXEBS_MAX_TIMEOUT_SEC 3 | |
| //#define PXEBS_MAX_TIMEOUT_SEC 7 /* as per PXE spec */ | |
| #include <config/local/dhcp.h> | |
| #endif /* CONFIG_DHCP_H */ |