MdeModulePkg/Bus/Pci/UhciDxe/UhciReg.h

/** @file

  The definition for UHCI register operation routines.

Copyright (c) 2007 - 2010, Intel Corporation. All rights reserved.<BR>
SPDX-License-Identifier: BSD-2-Clause-Patent

**/

#ifndef _EFI_UHCI_REG_H_
#define _EFI_UHCI_REG_H_

//
// UHCI register offset
//

#define UHCI_FRAME_NUM  1024

//
// Register offset and PCI related staff
//
#define USB_BAR_INDEX  4

#define USBCMD_OFFSET          0
#define USBSTS_OFFSET          2
#define USBINTR_OFFSET         4
#define USBPORTSC_OFFSET       0x10
#define USB_FRAME_NO_OFFSET    6
#define USB_FRAME_BASE_OFFSET  8
#define USB_EMULATION_OFFSET   0xC0

//
// Packet IDs
//
#define SETUP_PACKET_ID   0x2D
#define INPUT_PACKET_ID   0x69
#define OUTPUT_PACKET_ID  0xE1
#define ERROR_PACKET_ID   0x55

//
// USB port status and control bit definition.
//
#define USBPORTSC_CCS   BIT0        // Current Connect Status
#define USBPORTSC_CSC   BIT1        // Connect Status Change
#define USBPORTSC_PED   BIT2        // Port Enable / Disable
#define USBPORTSC_PEDC  BIT3        // Port Enable / Disable Change
#define USBPORTSC_LSL   BIT4        // Line Status Low BIT
#define USBPORTSC_LSH   BIT5        // Line Status High BIT
#define USBPORTSC_RD    BIT6        // Resume Detect
#define USBPORTSC_LSDA  BIT8        // Low Speed Device Attached
#define USBPORTSC_PR    BIT9        // Port Reset
#define USBPORTSC_SUSP  BIT12       // Suspend

//
// UHCI Spec said it must implement 2 ports each host at least,
// and if more, check whether the bit7 of PORTSC is always 1.
// So here assume the max of port number each host is 16.
//
#define USB_MAX_ROOTHUB_PORT  0x0F

//
// Command register bit definitions
//
#define USBCMD_RS       BIT0        // Run/Stop
#define USBCMD_HCRESET  BIT1        // Host reset
#define USBCMD_GRESET   BIT2        // Global reset
#define USBCMD_EGSM     BIT3        // Global Suspend Mode
#define USBCMD_FGR      BIT4        // Force Global Resume
#define USBCMD_SWDBG    BIT5        // SW Debug mode
#define USBCMD_CF       BIT6        // Config Flag (sw only)
#define USBCMD_MAXP     BIT7        // Max Packet (0 = 32, 1 = 64)

//
// USB Status register bit definitions
//
#define USBSTS_USBINT  BIT0         // Interrupt due to IOC
#define USBSTS_ERROR   BIT1         // Interrupt due to error
#define USBSTS_RD      BIT2         // Resume Detect
#define USBSTS_HSE     BIT3         // Host System Error
#define USBSTS_HCPE    BIT4         // Host Controller Process Error
#define USBSTS_HCH     BIT5         // HC Halted

#define USBTD_ACTIVE    BIT7        // TD is still active
#define USBTD_STALLED   BIT6        // TD is stalled
#define USBTD_BUFFERR   BIT5        // Buffer underflow or overflow
#define USBTD_BABBLE    BIT4        // Babble condition
#define USBTD_NAK       BIT3        // NAK is received
#define USBTD_CRC       BIT2        // CRC/Time out error
#define USBTD_BITSTUFF  BIT1        // Bit stuff error

/**
  Read a UHCI register.

  @param  PciIo        The EFI_PCI_IO_PROTOCOL to use.
  @param  Offset       Register offset to USB_BAR_INDEX.

  @return Content of register.

**/
UINT16
UhciReadReg (
  IN EFI_PCI_IO_PROTOCOL  *PciIo,
  IN UINT32               Offset
  );

/**
  Write data to UHCI register.

  @param  PciIo        The EFI_PCI_IO_PROTOCOL to use.
  @param  Offset       Register offset to USB_BAR_INDEX.
  @param  Data         Data to write.

  @return None.

**/
VOID
UhciWriteReg (
  IN EFI_PCI_IO_PROTOCOL  *PciIo,
  IN UINT32               Offset,
  IN UINT16               Data
  );

/**
  Set a bit of the UHCI Register.

  @param  PciIo        The EFI_PCI_IO_PROTOCOL to use.
  @param  Offset       Register offset to USB_BAR_INDEX.
  @param  Bit          The bit to set.

  @return None.

**/
VOID
UhciSetRegBit (
  IN EFI_PCI_IO_PROTOCOL  *PciIo,
  IN UINT32               Offset,
  IN UINT16               Bit
  );

/**
  Clear a bit of the UHCI Register.

  @param  PciIo        The PCI_IO protocol to access the PCI.
  @param  Offset       Register offset to USB_BAR_INDEX.
  @param  Bit          The bit to clear.

  @return None.

**/
VOID
UhciClearRegBit (
  IN EFI_PCI_IO_PROTOCOL  *PciIo,
  IN UINT32               Offset,
  IN UINT16               Bit
  );

/**
  Clear all the interrutp status bits, these bits
  are Write-Clean.

  @param  Uhc          The UHCI device.

  @return None.

**/
VOID
UhciAckAllInterrupt (
  IN  USB_HC_DEV  *Uhc
  );

/**
  Stop the host controller.

  @param  Uhc          The UHCI device.
  @param  Timeout      Max time allowed.

  @retval EFI_SUCCESS  The host controller is stopped.
  @retval EFI_TIMEOUT  Failed to stop the host controller.

**/
EFI_STATUS
UhciStopHc (
  IN USB_HC_DEV  *Uhc,
  IN UINTN       Timeout
  );

/**
  Check whether the host controller operates well.

  @param  PciIo        The PCI_IO protocol to use.

  @retval TRUE         Host controller is working.
  @retval FALSE        Host controller is halted or system error.

**/
BOOLEAN
UhciIsHcWorking (
  IN EFI_PCI_IO_PROTOCOL  *PciIo
  );

/**
  Set the UHCI frame list base address. It can't use
  UhciWriteReg which access memory in UINT16.

  @param  PciIo        The EFI_PCI_IO_PROTOCOL to use.
  @param  Addr         Address to set.

  @return None.

**/
VOID
UhciSetFrameListBaseAddr (
  IN EFI_PCI_IO_PROTOCOL  *PciIo,
  IN VOID                 *Addr
  );

/**
  Disable USB Emulation.

  @param  PciIo        The EFI_PCI_IO_PROTOCOL protocol to use.

  @return None.

**/
VOID
UhciTurnOffUsbEmulation (
  IN EFI_PCI_IO_PROTOCOL  *PciIo
  );

#endif