| /** @file | |
| Header file for SD memory card support. | |
| This header file contains some definitions defined in SD Physical Layer Simplified | |
| Specification Version 4.10 spec. | |
| Copyright (c) 2015, Intel Corporation. All rights reserved.<BR> | |
| This program and the accompanying materials | |
| are licensed and made available under the terms and conditions of the BSD License | |
| which accompanies this distribution. The full text of the license may be found at | |
| http://opensource.org/licenses/bsd-license.php | |
| THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, | |
| WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. | |
| **/ | |
| #ifndef __SD_H__ | |
| #define __SD_H__ | |
| // | |
| // SD command index | |
| // | |
| #define SD_GO_IDLE_STATE 0 | |
| #define SD_ALL_SEND_CID 2 | |
| #define SD_SET_RELATIVE_ADDR 3 | |
| #define SD_SET_DSR 4 | |
| #define SDIO_SEND_OP_COND 5 | |
| #define SD_SWITCH_FUNC 6 | |
| #define SD_SELECT_DESELECT_CARD 7 | |
| #define SD_SEND_IF_COND 8 | |
| #define SD_SEND_CSD 9 | |
| #define SD_SEND_CID 10 | |
| #define SD_VOLTAGE_SWITCH 11 | |
| #define SD_STOP_TRANSMISSION 12 | |
| #define SD_SEND_STATUS 13 | |
| #define SD_GO_INACTIVE_STATE 15 | |
| #define SD_SET_BLOCKLEN 16 | |
| #define SD_READ_SINGLE_BLOCK 17 | |
| #define SD_READ_MULTIPLE_BLOCK 18 | |
| #define SD_SEND_TUNING_BLOCK 19 | |
| #define SD_SPEED_CLASS_CONTROL 20 | |
| #define SD_SET_BLOCK_COUNT 23 | |
| #define SD_WRITE_SINGLE_BLOCK 24 | |
| #define SD_WRITE_MULTIPLE_BLOCK 25 | |
| #define SD_PROGRAM_CSD 27 | |
| #define SD_SET_WRITE_PROT 28 | |
| #define SD_CLR_WRITE_PROT 29 | |
| #define SD_SEND_WRITE_PROT 30 | |
| #define SD_ERASE_WR_BLK_START 32 | |
| #define SD_ERASE_WR_BLK_END 33 | |
| #define SD_ERASE 38 | |
| #define SD_LOCK_UNLOCK 42 | |
| #define SD_READ_EXTR_SINGLE 48 | |
| #define SD_WRITE_EXTR_SINGLE 49 | |
| #define SDIO_RW_DIRECT 52 | |
| #define SDIO_RW_EXTENDED 53 | |
| #define SD_APP_CMD 55 | |
| #define SD_GEN_CMD 56 | |
| #define SD_READ_EXTR_MULTI 58 | |
| #define SD_WRITE_EXTR_MULTI 59 | |
| #define SD_SET_BUS_WIDTH 6 // ACMD6 | |
| #define SD_STATUS 13 // ACMD13 | |
| #define SD_SEND_NUM_WR_BLOCKS 22 // ACMD22 | |
| #define SD_SET_WR_BLK_ERASE_COUNT 23 // ACMD23 | |
| #define SD_SEND_OP_COND 41 // ACMD41 | |
| #define SD_SET_CLR_CARD_DETECT 42 // ACMD42 | |
| #define SD_SEND_SCR 51 // ACMD51 | |
| #pragma pack(1) | |
| typedef struct { | |
| UINT8 NotUsed:1; // Not used [0:0] | |
| UINT8 Crc:7; // CRC [7:1] | |
| UINT16 ManufacturingDate:12; // Manufacturing date [19:8] | |
| UINT16 Reserved:4; // Reserved [23:20] | |
| UINT8 ProductSerialNumber[4]; // Product serial number [55:24] | |
| UINT8 ProductRevision; // Product revision [63:56] | |
| UINT8 ProductName[5]; // Product name [103:64] | |
| UINT8 OemId[2]; // OEM/Application ID [119:104] | |
| UINT8 ManufacturerId; // Manufacturer ID [127:120] | |
| } SD_CID; | |
| typedef struct { | |
| UINT32 NotUsed:1; // Not used [0:0] | |
| UINT32 Crc:7; // CRC [7:1] | |
| UINT32 Reserved:2; // Reserved [9:8] | |
| UINT32 FileFormat:2; // File format [11:10] | |
| UINT32 TmpWriteProtect:1; // Temporary write protection [12:12] | |
| UINT32 PermWriteProtect:1; // Permanent write protection [13:13] | |
| UINT32 Copy:1; // Copy flag (OTP) [14:14] | |
| UINT32 FileFormatGrp:1; // File format group [15:15] | |
| UINT32 Reserved1:5; // Reserved [20:16] | |
| UINT32 WriteBlPartial:1; // Partial blocks for write allowed [21:21] | |
| UINT32 WriteBlLen:4; // Max. write data block length [25:22] | |
| UINT32 R2WFactor:3; // Write speed factor [28:26] | |
| UINT32 Reserved2:2; // Manufacturer default ECC [30:29] | |
| UINT32 WpGrpEnable:1; // Write protect group enable [31:31] | |
| UINT32 WpGrpSize:7; // Write protect group size [38:32] | |
| UINT32 SectorSize:7; // Erase sector size [45:39] | |
| UINT32 EraseBlkEn:1; // Erase single block enable [46:46] | |
| UINT32 CSizeMul:3; // device size multiplier [49:47] | |
| UINT32 VddWCurrMax:3; // max. write current @VDD max [52:50] | |
| UINT32 VddWCurrMin:3; // max. write current @VDD min [55:53] | |
| UINT32 VddRCurrMax:3; // max. read current @VDD max [58:56] | |
| UINT32 VddRCurrMin:3; // max. read current @VDD min [61:59] | |
| UINT32 CSizeLow:2; // Device size low 2 bits [63:62] | |
| UINT32 CSizeHigh:10; // Device size high 10 bits [73:64] | |
| UINT32 Reserved4:2; // Reserved [75:74] | |
| UINT32 DsrImp:1; // DSR implemented [76:76] | |
| UINT32 ReadBlkMisalign:1; // Read block misalignment [77:77] | |
| UINT32 WriteBlkMisalign:1; // Write block misalignment [78:78] | |
| UINT32 ReadBlPartial:1; // Partial blocks for read allowed [79:79] | |
| UINT32 ReadBlLen:4; // Max. read data block length [83:80] | |
| UINT32 Ccc:12; // Card command classes [95:84] | |
| UINT32 TranSpeed:8; // Max. data transfer rate [103:96] | |
| UINT32 Nsac:8; // Data read access-time in CLK cycles (NSAC*100) [111:104] | |
| UINT32 Taac:8; // Data read access-time [119:112] | |
| UINT32 Reserved5:6; // Reserved [125:120] | |
| UINT32 CsdStructure:2; // CSD structure [127:126] | |
| } SD_CSD; | |
| typedef struct { | |
| UINT32 NotUsed:1; // Not used [0:0] | |
| UINT32 Crc:7; // CRC [7:1] | |
| UINT32 Reserved:2; // Reserved [9:8] | |
| UINT32 FileFormat:2; // File format [11:10] | |
| UINT32 TmpWriteProtect:1; // Temporary write protection [12:12] | |
| UINT32 PermWriteProtect:1; // Permanent write protection [13:13] | |
| UINT32 Copy:1; // Copy flag (OTP) [14:14] | |
| UINT32 FileFormatGrp:1; // File format group [15:15] | |
| UINT32 Reserved1:5; // Reserved [20:16] | |
| UINT32 WriteBlPartial:1; // Partial blocks for write allowed [21:21] | |
| UINT32 WriteBlLen:4; // Max. write data block length [25:22] | |
| UINT32 R2WFactor:3; // Write speed factor [28:26] | |
| UINT32 Reserved2:2; // Manufacturer default ECC [30:29] | |
| UINT32 WpGrpEnable:1; // Write protect group enable [31:31] | |
| UINT32 WpGrpSize:7; // Write protect group size [38:32] | |
| UINT32 SectorSize:7; // Erase sector size [45:39] | |
| UINT32 EraseBlkEn:1; // Erase single block enable [46:46] | |
| UINT32 Reserved3:1; // Reserved [47:47] | |
| UINT32 CSizeLow:16; // Device size low 16 bits [63:48] | |
| UINT32 CSizeHigh:6; // Device size high 6 bits [69:64] | |
| UINT32 Reserved4:6; // Reserved [75:70] | |
| UINT32 DsrImp:1; // DSR implemented [76:76] | |
| UINT32 ReadBlkMisalign:1; // Read block misalignment [77:77] | |
| UINT32 WriteBlkMisalign:1; // Write block misalignment [78:78] | |
| UINT32 ReadBlPartial:1; // Partial blocks for read allowed [79:79] | |
| UINT32 ReadBlLen:4; // Max. read data block length [83:80] | |
| UINT32 Ccc:12; // Card command classes [95:84] | |
| UINT32 TranSpeed:8; // Max. data transfer rate [103:96] | |
| UINT32 Nsac:8; // Data read access-time in CLK cycles (NSAC*100) [111:104] | |
| UINT32 Taac:8; // Data read access-time [119:112] | |
| UINT32 Reserved5:6; // Reserved [125:120] | |
| UINT32 CsdStructure:2; // CSD structure [127:126] | |
| } SD_CSD2; | |
| typedef struct { | |
| UINT32 Reserved; // Reserved [31:0] | |
| UINT32 CmdSupport:4; // Command Support bits [35:32] | |
| UINT32 Reserved1:6; // Reserved [41:36] | |
| UINT32 SdSpec4:1; // Spec. Version 4.00 or higher [42:42] | |
| UINT32 ExSecurity:4; // Extended Security Support [46:43] | |
| UINT32 SdSpec3:1; // Spec. Version 3.00 or higher [47:47] | |
| UINT32 SdBusWidths:4; // DAT Bus widths supported [51:48] | |
| UINT32 SdSecurity:3; // CPRM security support [54:52] | |
| UINT32 DataStatAfterErase:1; // Data status after erases [55] | |
| UINT32 SdSpec:4; // SD Memory Card Spec. Version [59:56] | |
| UINT32 ScrStructure:4; // SCR Structure [63:60] | |
| } SD_SCR; | |
| #pragma pack() | |
| #endif |