| /** @file |
| This driver module produces IDE_CONTROLLER_INIT protocol for Sata Controllers. |
| |
| Copyright (c) 2011, Intel Corporation. All rights reserved.<BR> |
| This program and the accompanying materials |
| are licensed and made available under the terms and conditions of the BSD License |
| which accompanies this distribution. The full text of the license may be found at |
| http://opensource.org/licenses/bsd-license.php |
| |
| THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, |
| WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. |
| |
| **/ |
| |
| #include "SataController.h" |
| |
| /// |
| /// EFI_DRIVER_BINDING_PROTOCOL instance |
| /// |
| EFI_DRIVER_BINDING_PROTOCOL gSataControllerDriverBinding = { |
| SataControllerSupported, |
| SataControllerStart, |
| SataControllerStop, |
| 0xa, |
| NULL, |
| NULL |
| }; |
| |
| /** |
| Read AHCI Operation register. |
| |
| @param PciIo The PCI IO protocol instance. |
| @param Offset The operation register offset. |
| |
| @return The register content read. |
| |
| **/ |
| UINT32 |
| EFIAPI |
| AhciReadReg ( |
| IN EFI_PCI_IO_PROTOCOL *PciIo, |
| IN UINT32 Offset |
| ) |
| { |
| UINT32 Data; |
| |
| ASSERT (PciIo != NULL); |
| |
| Data = 0; |
| |
| PciIo->Mem.Read ( |
| PciIo, |
| EfiPciIoWidthUint32, |
| AHCI_BAR_INDEX, |
| (UINT64) Offset, |
| 1, |
| &Data |
| ); |
| |
| return Data; |
| } |
| |
| /** |
| Write AHCI Operation register. |
| |
| @param PciIo The PCI IO protocol instance. |
| @param Offset The operation register offset. |
| @param Data The data used to write down. |
| |
| **/ |
| VOID |
| EFIAPI |
| AhciWriteReg ( |
| IN EFI_PCI_IO_PROTOCOL *PciIo, |
| IN UINT32 Offset, |
| IN UINT32 Data |
| ) |
| { |
| ASSERT (PciIo != NULL); |
| |
| PciIo->Mem.Write ( |
| PciIo, |
| EfiPciIoWidthUint32, |
| AHCI_BAR_INDEX, |
| (UINT64) Offset, |
| 1, |
| &Data |
| ); |
| |
| return; |
| } |
| |
| /** |
| This function is used to calculate the best PIO mode supported by specific IDE device |
| |
| @param IdentifyData The identify data of specific IDE device. |
| @param DisPioMode Disqualified PIO modes collection. |
| @param SelectedMode Available PIO modes collection. |
| |
| @retval EFI_SUCCESS Best PIO modes are returned. |
| @retval EFI_UNSUPPORTED The device doesn't support PIO mode, |
| or all supported modes have been disqualified. |
| **/ |
| EFI_STATUS |
| CalculateBestPioMode ( |
| IN EFI_IDENTIFY_DATA *IdentifyData, |
| IN UINT16 *DisPioMode OPTIONAL, |
| OUT UINT16 *SelectedMode |
| ) |
| { |
| UINT16 PioMode; |
| UINT16 AdvancedPioMode; |
| UINT16 Temp; |
| UINT16 Index; |
| UINT16 MinimumPioCycleTime; |
| |
| Temp = 0xff; |
| |
| PioMode = (UINT8) (((ATA5_IDENTIFY_DATA *) (&(IdentifyData->AtaData)))->pio_cycle_timing >> 8); |
| |
| // |
| // See whether Identify Data word 64 - 70 are valid |
| // |
| if ((IdentifyData->AtaData.field_validity & 0x02) == 0x02) { |
| |
| AdvancedPioMode = IdentifyData->AtaData.advanced_pio_modes; |
| DEBUG ((EFI_D_INFO, "CalculateBestPioMode: AdvancedPioMode = %x\n", AdvancedPioMode)); |
| |
| for (Index = 0; Index < 8; Index++) { |
| if ((AdvancedPioMode & 0x01) != 0) { |
| Temp = Index; |
| } |
| |
| AdvancedPioMode >>= 1; |
| } |
| |
| // |
| // If Temp is modified, mean the advanced_pio_modes is not zero; |
| // if Temp is not modified, mean there is no advanced PIO mode supported, |
| // the best PIO Mode is the value in pio_cycle_timing. |
| // |
| if (Temp != 0xff) { |
| AdvancedPioMode = (UINT16) (Temp + 3); |
| } else { |
| AdvancedPioMode = PioMode; |
| } |
| |
| // |
| // Limit the PIO mode to at most PIO4. |
| // |
| PioMode = (UINT16) MIN (AdvancedPioMode, 4); |
| |
| MinimumPioCycleTime = IdentifyData->AtaData.min_pio_cycle_time_with_flow_control; |
| |
| if (MinimumPioCycleTime <= 120) { |
| PioMode = (UINT16) MIN (4, PioMode); |
| } else if (MinimumPioCycleTime <= 180) { |
| PioMode = (UINT16) MIN (3, PioMode); |
| } else if (MinimumPioCycleTime <= 240) { |
| PioMode = (UINT16) MIN (2, PioMode); |
| } else { |
| PioMode = 0; |
| } |
| |
| // |
| // Degrade the PIO mode if the mode has been disqualified |
| // |
| if (DisPioMode != NULL) { |
| if (*DisPioMode < 2) { |
| return EFI_UNSUPPORTED; // no mode below ATA_PIO_MODE_BELOW_2 |
| } |
| |
| if (PioMode >= *DisPioMode) { |
| PioMode = (UINT16) (*DisPioMode - 1); |
| } |
| } |
| |
| if (PioMode < 2) { |
| *SelectedMode = 1; // ATA_PIO_MODE_BELOW_2; |
| } else { |
| *SelectedMode = PioMode; // ATA_PIO_MODE_2 to ATA_PIO_MODE_4; |
| } |
| |
| } else { |
| // |
| // Identify Data word 64 - 70 are not valid |
| // Degrade the PIO mode if the mode has been disqualified |
| // |
| if (DisPioMode != NULL) { |
| if (*DisPioMode < 2) { |
| return EFI_UNSUPPORTED; // no mode below ATA_PIO_MODE_BELOW_2 |
| } |
| |
| if (PioMode == *DisPioMode) { |
| PioMode--; |
| } |
| } |
| |
| if (PioMode < 2) { |
| *SelectedMode = 1; // ATA_PIO_MODE_BELOW_2; |
| } else { |
| *SelectedMode = 2; // ATA_PIO_MODE_2; |
| } |
| |
| } |
| |
| return EFI_SUCCESS; |
| } |
| |
| /** |
| This function is used to calculate the best UDMA mode supported by specific IDE device |
| |
| @param IdentifyData The identify data of specific IDE device. |
| @param DisUDmaMode Disqualified UDMA modes collection. |
| @param SelectedMode Available UDMA modes collection. |
| |
| @retval EFI_SUCCESS Best UDMA modes are returned. |
| @retval EFI_UNSUPPORTED The device doesn't support UDMA mode, |
| or all supported modes have been disqualified. |
| **/ |
| EFI_STATUS |
| CalculateBestUdmaMode ( |
| IN EFI_IDENTIFY_DATA *IdentifyData, |
| IN UINT16 *DisUDmaMode OPTIONAL, |
| OUT UINT16 *SelectedMode |
| ) |
| { |
| UINT16 TempMode; |
| UINT16 DeviceUDmaMode; |
| |
| DeviceUDmaMode = 0; |
| |
| // |
| // Check whether the WORD 88 (supported UltraDMA by drive) is valid |
| // |
| if ((IdentifyData->AtaData.field_validity & 0x04) == 0x00) { |
| return EFI_UNSUPPORTED; |
| } |
| |
| DeviceUDmaMode = IdentifyData->AtaData.ultra_dma_mode; |
| DEBUG ((EFI_D_INFO, "CalculateBestUdmaMode: DeviceUDmaMode = %x\n", DeviceUDmaMode)); |
| DeviceUDmaMode &= 0x3f; |
| TempMode = 0; // initialize it to UDMA-0 |
| |
| while ((DeviceUDmaMode >>= 1) != 0) { |
| TempMode++; |
| } |
| |
| // |
| // Degrade the UDMA mode if the mode has been disqualified |
| // |
| if (DisUDmaMode != NULL) { |
| if (*DisUDmaMode == 0) { |
| *SelectedMode = 0; |
| return EFI_UNSUPPORTED; // no mode below ATA_UDMA_MODE_0 |
| } |
| |
| if (TempMode >= *DisUDmaMode) { |
| TempMode = (UINT16) (*DisUDmaMode - 1); |
| } |
| } |
| |
| // |
| // Possible returned mode is between ATA_UDMA_MODE_0 and ATA_UDMA_MODE_5 |
| // |
| *SelectedMode = TempMode; |
| |
| return EFI_SUCCESS; |
| } |
| |
| /** |
| The Entry Point of module. It follows the standard UEFI driver model. |
| |
| @param[in] ImageHandle The firmware allocated handle for the EFI image. |
| @param[in] SystemTable A pointer to the EFI System Table. |
| |
| @retval EFI_SUCCESS The entry point is executed successfully. |
| @retval other Some error occurs when executing this entry point. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| InitializeSataControllerDriver ( |
| IN EFI_HANDLE ImageHandle, |
| IN EFI_SYSTEM_TABLE *SystemTable |
| ) |
| { |
| EFI_STATUS Status; |
| |
| // |
| // Install driver model protocol(s). |
| // |
| Status = EfiLibInstallDriverBindingComponentName2 ( |
| ImageHandle, |
| SystemTable, |
| &gSataControllerDriverBinding, |
| ImageHandle, |
| &gSataControllerComponentName, |
| &gSataControllerComponentName2 |
| ); |
| ASSERT_EFI_ERROR (Status); |
| |
| return Status; |
| } |
| |
| /** |
| Supported function of Driver Binding protocol for this driver. |
| Test to see if this driver supports ControllerHandle. |
| |
| @param This Protocol instance pointer. |
| @param Controller Handle of device to test. |
| @param RemainingDevicePath A pointer to the device path. |
| it should be ignored by device driver. |
| |
| @retval EFI_SUCCESS This driver supports this device. |
| @retval EFI_ALREADY_STARTED This driver is already running on this device. |
| @retval other This driver does not support this device. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| SataControllerSupported ( |
| IN EFI_DRIVER_BINDING_PROTOCOL *This, |
| IN EFI_HANDLE Controller, |
| IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath |
| ) |
| { |
| EFI_STATUS Status; |
| EFI_PCI_IO_PROTOCOL *PciIo; |
| PCI_TYPE00 PciData; |
| |
| // |
| // Attempt to open PCI I/O Protocol |
| // |
| Status = gBS->OpenProtocol ( |
| Controller, |
| &gEfiPciIoProtocolGuid, |
| (VOID **) &PciIo, |
| This->DriverBindingHandle, |
| Controller, |
| EFI_OPEN_PROTOCOL_GET_PROTOCOL |
| ); |
| if (EFI_ERROR (Status)) { |
| return Status; |
| } |
| |
| // |
| // Now further check the PCI header: Base Class (offset 0x0B) and |
| // Sub Class (offset 0x0A). This controller should be an SATA controller |
| // |
| Status = PciIo->Pci.Read ( |
| PciIo, |
| EfiPciIoWidthUint8, |
| PCI_CLASSCODE_OFFSET, |
| sizeof (PciData.Hdr.ClassCode), |
| PciData.Hdr.ClassCode |
| ); |
| if (EFI_ERROR (Status)) { |
| return EFI_UNSUPPORTED; |
| } |
| |
| if (IS_PCI_IDE (&PciData) || IS_PCI_SATADPA (&PciData)) { |
| return EFI_SUCCESS; |
| } |
| |
| return EFI_UNSUPPORTED; |
| } |
| |
| /** |
| This routine is called right after the .Supported() called and |
| Start this driver on ControllerHandle. |
| |
| @param This Protocol instance pointer. |
| @param Controller Handle of device to bind driver to. |
| @param RemainingDevicePath A pointer to the device path. |
| it should be ignored by device driver. |
| |
| @retval EFI_SUCCESS This driver is added to this device. |
| @retval EFI_ALREADY_STARTED This driver is already running on this device. |
| @retval other Some error occurs when binding this driver to this device. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| SataControllerStart ( |
| IN EFI_DRIVER_BINDING_PROTOCOL *This, |
| IN EFI_HANDLE Controller, |
| IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath |
| ) |
| { |
| EFI_STATUS Status; |
| EFI_PCI_IO_PROTOCOL *PciIo; |
| PCI_TYPE00 PciData; |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; |
| UINT32 Data32; |
| UINTN ChannelDeviceCount; |
| |
| DEBUG ((EFI_D_INFO, "SataControllerStart START\n")); |
| |
| SataPrivateData = NULL; |
| |
| // |
| // Now test and open PCI I/O Protocol |
| // |
| Status = gBS->OpenProtocol ( |
| Controller, |
| &gEfiPciIoProtocolGuid, |
| (VOID **) &PciIo, |
| This->DriverBindingHandle, |
| Controller, |
| EFI_OPEN_PROTOCOL_BY_DRIVER |
| ); |
| if (EFI_ERROR (Status)) { |
| DEBUG ((EFI_D_ERROR, "SataControllerStart error return status = %r\n", Status)); |
| return Status; |
| } |
| |
| // |
| // Allocate Sata Private Data structure |
| // |
| SataPrivateData = AllocateZeroPool (sizeof (EFI_SATA_CONTROLLER_PRIVATE_DATA)); |
| if (SataPrivateData == NULL) { |
| Status = EFI_OUT_OF_RESOURCES; |
| goto Done; |
| } |
| |
| // |
| // Initialize Sata Private Data |
| // |
| SataPrivateData->Signature = SATA_CONTROLLER_SIGNATURE; |
| SataPrivateData->PciIo = PciIo; |
| SataPrivateData->IdeInit.GetChannelInfo = IdeInitGetChannelInfo; |
| SataPrivateData->IdeInit.NotifyPhase = IdeInitNotifyPhase; |
| SataPrivateData->IdeInit.SubmitData = IdeInitSubmitData; |
| SataPrivateData->IdeInit.DisqualifyMode = IdeInitDisqualifyMode; |
| SataPrivateData->IdeInit.CalculateMode = IdeInitCalculateMode; |
| SataPrivateData->IdeInit.SetTiming = IdeInitSetTiming; |
| SataPrivateData->IdeInit.EnumAll = SATA_ENUMER_ALL; |
| |
| Status = PciIo->Pci.Read ( |
| PciIo, |
| EfiPciIoWidthUint8, |
| PCI_CLASSCODE_OFFSET, |
| sizeof (PciData.Hdr.ClassCode), |
| PciData.Hdr.ClassCode |
| ); |
| ASSERT_EFI_ERROR (Status); |
| |
| if (IS_PCI_IDE (&PciData)) { |
| SataPrivateData->IdeInit.ChannelCount = IDE_MAX_CHANNEL; |
| SataPrivateData->DeviceCount = IDE_MAX_DEVICES; |
| } else if (IS_PCI_SATADPA (&PciData)) { |
| // |
| // Read Host Capability Register(CAP) to get Number of Ports(NPS) and Supports Port Multiplier(SPM) |
| // NPS is 0's based value indicating the maximum number of ports supported by the HBA silicon. |
| // A maximum of 32 ports can be supported. A value of '0h', indicating one port, is the minimum requirement. |
| // |
| Data32 = AhciReadReg (PciIo, R_AHCI_CAP); |
| SataPrivateData->IdeInit.ChannelCount = (UINT8) ((Data32 & B_AHCI_CAP_NPS) + 1); |
| SataPrivateData->DeviceCount = AHCI_MAX_DEVICES; |
| if ((Data32 & B_AHCI_CAP_SPM) == B_AHCI_CAP_SPM) { |
| SataPrivateData->DeviceCount = AHCI_MULTI_MAX_DEVICES; |
| } |
| } |
| |
| ChannelDeviceCount = (UINTN) (SataPrivateData->IdeInit.ChannelCount) * (UINTN) (SataPrivateData->DeviceCount); |
| SataPrivateData->DisqualifiedModes = AllocateZeroPool ((sizeof (EFI_ATA_COLLECTIVE_MODE)) * ChannelDeviceCount); |
| if (SataPrivateData->DisqualifiedModes == NULL) { |
| Status = EFI_OUT_OF_RESOURCES; |
| goto Done; |
| } |
| |
| SataPrivateData->IdentifyData = AllocateZeroPool ((sizeof (EFI_IDENTIFY_DATA)) * ChannelDeviceCount); |
| if (SataPrivateData->IdentifyData == NULL) { |
| Status = EFI_OUT_OF_RESOURCES; |
| goto Done; |
| } |
| |
| SataPrivateData->IdentifyValid = AllocateZeroPool ((sizeof (BOOLEAN)) * ChannelDeviceCount); |
| if (SataPrivateData->IdentifyValid == NULL) { |
| Status = EFI_OUT_OF_RESOURCES; |
| goto Done; |
| } |
| |
| // |
| // Install IDE Controller Init Protocol to this instance |
| // |
| Status = gBS->InstallMultipleProtocolInterfaces ( |
| &Controller, |
| &gEfiIdeControllerInitProtocolGuid, |
| &(SataPrivateData->IdeInit), |
| NULL |
| ); |
| |
| Done: |
| if (EFI_ERROR (Status)) { |
| |
| gBS->CloseProtocol ( |
| Controller, |
| &gEfiPciIoProtocolGuid, |
| This->DriverBindingHandle, |
| Controller |
| ); |
| if (SataPrivateData != NULL) { |
| if (SataPrivateData->DisqualifiedModes != NULL) { |
| FreePool (SataPrivateData->DisqualifiedModes); |
| } |
| if (SataPrivateData->IdentifyData != NULL) { |
| FreePool (SataPrivateData->IdentifyData); |
| } |
| if (SataPrivateData->IdentifyValid != NULL) { |
| FreePool (SataPrivateData->IdentifyValid); |
| } |
| FreePool (SataPrivateData); |
| } |
| } |
| |
| DEBUG ((EFI_D_INFO, "SataControllerStart END status = %r\n", Status)); |
| |
| return Status; |
| } |
| |
| /** |
| Stop this driver on ControllerHandle. |
| |
| @param This Protocol instance pointer. |
| @param Controller Handle of device to stop driver on. |
| @param NumberOfChildren Not used. |
| @param ChildHandleBuffer Not used. |
| |
| @retval EFI_SUCCESS This driver is removed from this device. |
| @retval other Some error occurs when removing this driver from this device. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| SataControllerStop ( |
| IN EFI_DRIVER_BINDING_PROTOCOL *This, |
| IN EFI_HANDLE Controller, |
| IN UINTN NumberOfChildren, |
| IN EFI_HANDLE *ChildHandleBuffer |
| ) |
| { |
| EFI_STATUS Status; |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL *IdeInit; |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; |
| |
| // |
| // Open the produced protocol |
| // |
| Status = gBS->OpenProtocol ( |
| Controller, |
| &gEfiIdeControllerInitProtocolGuid, |
| (VOID **) &IdeInit, |
| This->DriverBindingHandle, |
| Controller, |
| EFI_OPEN_PROTOCOL_GET_PROTOCOL |
| ); |
| if (EFI_ERROR (Status)) { |
| return EFI_UNSUPPORTED; |
| } |
| |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (IdeInit); |
| ASSERT (SataPrivateData != NULL); |
| |
| // |
| // Uninstall the IDE Controller Init Protocol from this instance |
| // |
| Status = gBS->UninstallMultipleProtocolInterfaces ( |
| Controller, |
| &gEfiIdeControllerInitProtocolGuid, |
| &(SataPrivateData->IdeInit), |
| NULL |
| ); |
| if (EFI_ERROR (Status)) { |
| return Status; |
| } |
| |
| if (SataPrivateData != NULL) { |
| if (SataPrivateData->DisqualifiedModes != NULL) { |
| FreePool (SataPrivateData->DisqualifiedModes); |
| } |
| if (SataPrivateData->IdentifyData != NULL) { |
| FreePool (SataPrivateData->IdentifyData); |
| } |
| if (SataPrivateData->IdentifyValid != NULL) { |
| FreePool (SataPrivateData->IdentifyValid); |
| } |
| FreePool (SataPrivateData); |
| } |
| |
| // |
| // Close protocols opened by Sata Controller driver |
| // |
| return gBS->CloseProtocol ( |
| Controller, |
| &gEfiPciIoProtocolGuid, |
| This->DriverBindingHandle, |
| Controller |
| ); |
| } |
| |
| /** |
| Calculate the flat array subscript of a (Channel, Device) pair. |
| |
| @param[in] SataPrivateData The private data structure corresponding to the |
| SATA controller that attaches the device for |
| which the flat array subscript is being |
| calculated. |
| |
| @param[in] Channel The channel (ie. port) number on the SATA |
| controller that the device is attached to. |
| |
| @param[in] Device The device number on the channel. |
| |
| @return The flat array subscript suitable for indexing DisqualifiedModes, |
| IdentifyData, and IdentifyValid. |
| **/ |
| STATIC |
| UINTN |
| FlatDeviceIndex ( |
| IN CONST EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData, |
| IN UINTN Channel, |
| IN UINTN Device |
| ) |
| { |
| ASSERT (SataPrivateData != NULL); |
| ASSERT (Channel < SataPrivateData->IdeInit.ChannelCount); |
| ASSERT (Device < SataPrivateData->DeviceCount); |
| |
| return Channel * SataPrivateData->DeviceCount + Device; |
| } |
| |
| // |
| // Interface functions of IDE_CONTROLLER_INIT protocol |
| // |
| /** |
| Returns the information about the specified IDE channel. |
| |
| This function can be used to obtain information about a particular IDE channel. |
| The driver entity uses this information during the enumeration process. |
| |
| If Enabled is set to FALSE, the driver entity will not scan the channel. Note |
| that it will not prevent an operating system driver from scanning the channel. |
| |
| For most of today's controllers, MaxDevices will either be 1 or 2. For SATA |
| controllers, this value will always be 1. SATA configurations can contain SATA |
| port multipliers. SATA port multipliers behave like SATA bridges and can support |
| up to 16 devices on the other side. If a SATA port out of the IDE controller |
| is connected to a port multiplier, MaxDevices will be set to the number of SATA |
| devices that the port multiplier supports. Because today's port multipliers |
| support up to fifteen SATA devices, this number can be as large as fifteen. The IDE |
| bus driver is required to scan for the presence of port multipliers behind an SATA |
| controller and enumerate up to MaxDevices number of devices behind the port |
| multiplier. |
| |
| In this context, the devices behind a port multiplier constitute a channel. |
| |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. |
| @param[in] Channel Zero-based channel number. |
| @param[out] Enabled TRUE if this channel is enabled. Disabled channels |
| are not scanned to see if any devices are present. |
| @param[out] MaxDevices The maximum number of IDE devices that the bus driver |
| can expect on this channel. For the ATA/ATAPI |
| specification, version 6, this number will either be |
| one or two. For Serial ATA (SATA) configurations with a |
| port multiplier, this number can be as large as fifteen. |
| |
| @retval EFI_SUCCESS Information was returned without any errors. |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| IdeInitGetChannelInfo ( |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, |
| IN UINT8 Channel, |
| OUT BOOLEAN *Enabled, |
| OUT UINT8 *MaxDevices |
| ) |
| { |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); |
| ASSERT (SataPrivateData != NULL); |
| |
| if (Channel < This->ChannelCount) { |
| *Enabled = TRUE; |
| *MaxDevices = SataPrivateData->DeviceCount; |
| return EFI_SUCCESS; |
| } |
| |
| *Enabled = FALSE; |
| return EFI_INVALID_PARAMETER; |
| } |
| |
| /** |
| The notifications from the driver entity that it is about to enter a certain |
| phase of the IDE channel enumeration process. |
| |
| This function can be used to notify the IDE controller driver to perform |
| specific actions, including any chipset-specific initialization, so that the |
| chipset is ready to enter the next phase. Seven notification points are defined |
| at this time. |
| |
| More synchronization points may be added as required in the future. |
| |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. |
| @param[in] Phase The phase during enumeration. |
| @param[in] Channel Zero-based channel number. |
| |
| @retval EFI_SUCCESS The notification was accepted without any errors. |
| @retval EFI_UNSUPPORTED Phase is not supported. |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). |
| @retval EFI_NOT_READY This phase cannot be entered at this time; for |
| example, an attempt was made to enter a Phase |
| without having entered one or more previous |
| Phase. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| IdeInitNotifyPhase ( |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, |
| IN EFI_IDE_CONTROLLER_ENUM_PHASE Phase, |
| IN UINT8 Channel |
| ) |
| { |
| return EFI_SUCCESS; |
| } |
| |
| /** |
| Submits the device information to the IDE controller driver. |
| |
| This function is used by the driver entity to pass detailed information about |
| a particular device to the IDE controller driver. The driver entity obtains |
| this information by issuing an ATA or ATAPI IDENTIFY_DEVICE command. IdentifyData |
| is the pointer to the response data buffer. The IdentifyData buffer is owned |
| by the driver entity, and the IDE controller driver must make a local copy |
| of the entire buffer or parts of the buffer as needed. The original IdentifyData |
| buffer pointer may not be valid when |
| |
| - EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() or |
| - EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() is called at a later point. |
| |
| The IDE controller driver may consult various fields of EFI_IDENTIFY_DATA to |
| compute the optimum mode for the device. These fields are not limited to the |
| timing information. For example, an implementation of the IDE controller driver |
| may examine the vendor and type/mode field to match known bad drives. |
| |
| The driver entity may submit drive information in any order, as long as it |
| submits information for all the devices belonging to the enumeration group |
| before EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() is called for any device |
| in that enumeration group. If a device is absent, EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() |
| should be called with IdentifyData set to NULL. The IDE controller driver may |
| not have any other mechanism to know whether a device is present or not. Therefore, |
| setting IdentifyData to NULL does not constitute an error condition. |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() can be called only once for a |
| given (Channel, Device) pair. |
| |
| @param[in] This A pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. |
| @param[in] Channel Zero-based channel number. |
| @param[in] Device Zero-based device number on the Channel. |
| @param[in] IdentifyData The device's response to the ATA IDENTIFY_DEVICE command. |
| |
| @retval EFI_SUCCESS The information was accepted without any errors. |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). |
| @retval EFI_INVALID_PARAMETER Device is invalid. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| IdeInitSubmitData ( |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, |
| IN UINT8 Channel, |
| IN UINT8 Device, |
| IN EFI_IDENTIFY_DATA *IdentifyData |
| ) |
| { |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; |
| UINTN DeviceIndex; |
| |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); |
| ASSERT (SataPrivateData != NULL); |
| |
| if ((Channel >= This->ChannelCount) || (Device >= SataPrivateData->DeviceCount)) { |
| return EFI_INVALID_PARAMETER; |
| } |
| |
| DeviceIndex = FlatDeviceIndex (SataPrivateData, Channel, Device); |
| |
| // |
| // Make a local copy of device's IdentifyData and mark the valid flag |
| // |
| if (IdentifyData != NULL) { |
| CopyMem ( |
| &(SataPrivateData->IdentifyData[DeviceIndex]), |
| IdentifyData, |
| sizeof (EFI_IDENTIFY_DATA) |
| ); |
| |
| SataPrivateData->IdentifyValid[DeviceIndex] = TRUE; |
| } else { |
| SataPrivateData->IdentifyValid[DeviceIndex] = FALSE; |
| } |
| |
| return EFI_SUCCESS; |
| } |
| |
| /** |
| Disqualifies specific modes for an IDE device. |
| |
| This function allows the driver entity or other drivers (such as platform |
| drivers) to reject certain timing modes and request the IDE controller driver |
| to recalculate modes. This function allows the driver entity and the IDE |
| controller driver to negotiate the timings on a per-device basis. This function |
| is useful in the case of drives that lie about their capabilities. An example |
| is when the IDE device fails to accept the timing modes that are calculated |
| by the IDE controller driver based on the response to the Identify Drive command. |
| |
| If the driver entity does not want to limit the ATA timing modes and leave that |
| decision to the IDE controller driver, it can either not call this function for |
| the given device or call this function and set the Valid flag to FALSE for all |
| modes that are listed in EFI_ATA_COLLECTIVE_MODE. |
| |
| The driver entity may disqualify modes for a device in any order and any number |
| of times. |
| |
| This function can be called multiple times to invalidate multiple modes of the |
| same type (e.g., Programmed Input/Output [PIO] modes 3 and 4). See the ATA/ATAPI |
| specification for more information on PIO modes. |
| |
| For Serial ATA (SATA) controllers, this member function can be used to disqualify |
| a higher transfer rate mode on a given channel. For example, a platform driver |
| may inform the IDE controller driver to not use second-generation (Gen2) speeds |
| for a certain SATA drive. |
| |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. |
| @param[in] Channel The zero-based channel number. |
| @param[in] Device The zero-based device number on the Channel. |
| @param[in] BadModes The modes that the device does not support and that |
| should be disqualified. |
| |
| @retval EFI_SUCCESS The modes were accepted without any errors. |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). |
| @retval EFI_INVALID_PARAMETER Device is invalid. |
| @retval EFI_INVALID_PARAMETER IdentifyData is NULL. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| IdeInitDisqualifyMode ( |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, |
| IN UINT8 Channel, |
| IN UINT8 Device, |
| IN EFI_ATA_COLLECTIVE_MODE *BadModes |
| ) |
| { |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; |
| UINTN DeviceIndex; |
| |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); |
| ASSERT (SataPrivateData != NULL); |
| |
| if ((Channel >= This->ChannelCount) || (BadModes == NULL) || (Device >= SataPrivateData->DeviceCount)) { |
| return EFI_INVALID_PARAMETER; |
| } |
| |
| DeviceIndex = FlatDeviceIndex (SataPrivateData, Channel, Device); |
| |
| // |
| // Record the disqualified modes per channel per device. From ATA/ATAPI spec, |
| // if a mode is not supported, the modes higher than it is also not supported. |
| // |
| CopyMem ( |
| &(SataPrivateData->DisqualifiedModes[DeviceIndex]), |
| BadModes, |
| sizeof (EFI_ATA_COLLECTIVE_MODE) |
| ); |
| |
| return EFI_SUCCESS; |
| } |
| |
| /** |
| Returns the information about the optimum modes for the specified IDE device. |
| |
| This function is used by the driver entity to obtain the optimum ATA modes for |
| a specific device. The IDE controller driver takes into account the following |
| while calculating the mode: |
| - The IdentifyData inputs to EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() |
| - The BadModes inputs to EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() |
| |
| The driver entity is required to call EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() |
| for all the devices that belong to an enumeration group before calling |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() for any device in the same group. |
| |
| The IDE controller driver will use controller- and possibly platform-specific |
| algorithms to arrive at SupportedModes. The IDE controller may base its |
| decision on user preferences and other considerations as well. This function |
| may be called multiple times because the driver entity may renegotiate the mode |
| with the IDE controller driver using EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode(). |
| |
| The driver entity may collect timing information for various devices in any |
| order. The driver entity is responsible for making sure that all the dependencies |
| are satisfied. For example, the SupportedModes information for device A that |
| was previously returned may become stale after a call to |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() for device B. |
| |
| The buffer SupportedModes is allocated by the callee because the caller does |
| not necessarily know the size of the buffer. The type EFI_ATA_COLLECTIVE_MODE |
| is defined in a way that allows for future extensibility and can be of variable |
| length. This memory pool should be deallocated by the caller when it is no |
| longer necessary. |
| |
| The IDE controller driver for a Serial ATA (SATA) controller can use this |
| member function to force a lower speed (first-generation [Gen1] speeds on a |
| second-generation [Gen2]-capable hardware). The IDE controller driver can |
| also allow the driver entity to stay with the speed that has been negotiated |
| by the physical layer. |
| |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. |
| @param[in] Channel A zero-based channel number. |
| @param[in] Device A zero-based device number on the Channel. |
| @param[out] SupportedModes The optimum modes for the device. |
| |
| @retval EFI_SUCCESS SupportedModes was returned. |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). |
| @retval EFI_INVALID_PARAMETER Device is invalid. |
| @retval EFI_INVALID_PARAMETER SupportedModes is NULL. |
| @retval EFI_NOT_READY Modes cannot be calculated due to a lack of |
| data. This error may happen if |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() |
| and EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyData() |
| were not called for at least one drive in the |
| same enumeration group. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| IdeInitCalculateMode ( |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, |
| IN UINT8 Channel, |
| IN UINT8 Device, |
| OUT EFI_ATA_COLLECTIVE_MODE **SupportedModes |
| ) |
| { |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; |
| EFI_IDENTIFY_DATA *IdentifyData; |
| BOOLEAN IdentifyValid; |
| EFI_ATA_COLLECTIVE_MODE *DisqualifiedModes; |
| UINT16 SelectedMode; |
| EFI_STATUS Status; |
| UINTN DeviceIndex; |
| |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); |
| ASSERT (SataPrivateData != NULL); |
| |
| if ((Channel >= This->ChannelCount) || (SupportedModes == NULL) || (Device >= SataPrivateData->DeviceCount)) { |
| return EFI_INVALID_PARAMETER; |
| } |
| |
| *SupportedModes = AllocateZeroPool (sizeof (EFI_ATA_COLLECTIVE_MODE)); |
| if (*SupportedModes == NULL) { |
| ASSERT (*SupportedModes != NULL); |
| return EFI_OUT_OF_RESOURCES; |
| } |
| |
| DeviceIndex = FlatDeviceIndex (SataPrivateData, Channel, Device); |
| |
| IdentifyData = &(SataPrivateData->IdentifyData[DeviceIndex]); |
| IdentifyValid = SataPrivateData->IdentifyValid[DeviceIndex]; |
| DisqualifiedModes = &(SataPrivateData->DisqualifiedModes[DeviceIndex]); |
| |
| // |
| // Make sure we've got the valid identify data of the device from SubmitData() |
| // |
| if (!IdentifyValid) { |
| FreePool (*SupportedModes); |
| return EFI_NOT_READY; |
| } |
| |
| Status = CalculateBestPioMode ( |
| IdentifyData, |
| (DisqualifiedModes->PioMode.Valid ? ((UINT16 *) &(DisqualifiedModes->PioMode.Mode)) : NULL), |
| &SelectedMode |
| ); |
| if (!EFI_ERROR (Status)) { |
| (*SupportedModes)->PioMode.Valid = TRUE; |
| (*SupportedModes)->PioMode.Mode = SelectedMode; |
| |
| } else { |
| (*SupportedModes)->PioMode.Valid = FALSE; |
| } |
| DEBUG ((EFI_D_INFO, "IdeInitCalculateMode: PioMode = %x\n", (*SupportedModes)->PioMode.Mode)); |
| |
| Status = CalculateBestUdmaMode ( |
| IdentifyData, |
| (DisqualifiedModes->UdmaMode.Valid ? ((UINT16 *) &(DisqualifiedModes->UdmaMode.Mode)) : NULL), |
| &SelectedMode |
| ); |
| |
| if (!EFI_ERROR (Status)) { |
| (*SupportedModes)->UdmaMode.Valid = TRUE; |
| (*SupportedModes)->UdmaMode.Mode = SelectedMode; |
| |
| } else { |
| (*SupportedModes)->UdmaMode.Valid = FALSE; |
| } |
| DEBUG ((EFI_D_INFO, "IdeInitCalculateMode: UdmaMode = %x\n", (*SupportedModes)->UdmaMode.Mode)); |
| |
| // |
| // The modes other than PIO and UDMA are not supported |
| // |
| return EFI_SUCCESS; |
| } |
| |
| /** |
| Commands the IDE controller driver to program the IDE controller hardware |
| so that the specified device can operate at the specified mode. |
| |
| This function is used by the driver entity to instruct the IDE controller |
| driver to program the IDE controller hardware to the specified modes. This |
| function can be called only once for a particular device. For a Serial ATA |
| (SATA) Advanced Host Controller Interface (AHCI) controller, no controller- |
| specific programming may be required. |
| |
| @param[in] This Pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. |
| @param[in] Channel Zero-based channel number. |
| @param[in] Device Zero-based device number on the Channel. |
| @param[in] Modes The modes to set. |
| |
| @retval EFI_SUCCESS The command was accepted without any errors. |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). |
| @retval EFI_INVALID_PARAMETER Device is invalid. |
| @retval EFI_NOT_READY Modes cannot be set at this time due to lack of data. |
| @retval EFI_DEVICE_ERROR Modes cannot be set due to hardware failure. |
| The driver entity should not use this device. |
| |
| **/ |
| EFI_STATUS |
| EFIAPI |
| IdeInitSetTiming ( |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, |
| IN UINT8 Channel, |
| IN UINT8 Device, |
| IN EFI_ATA_COLLECTIVE_MODE *Modes |
| ) |
| { |
| return EFI_SUCCESS; |
| } |