| /** @file | |
| This driver module produces IDE_CONTROLLER_INIT protocol for Sata Controllers. | |
| Copyright (c) 2011, Intel Corporation. All rights reserved.<BR> | |
| SPDX-License-Identifier: BSD-2-Clause-Patent | |
| **/ | |
| #include "SataController.h" | |
| /// | |
| /// EFI_DRIVER_BINDING_PROTOCOL instance | |
| /// | |
| EFI_DRIVER_BINDING_PROTOCOL gSataControllerDriverBinding = { | |
| SataControllerSupported, | |
| SataControllerStart, | |
| SataControllerStop, | |
| 0xa, | |
| NULL, | |
| NULL | |
| }; | |
| /** | |
| Read AHCI Operation register. | |
| @param PciIo The PCI IO protocol instance. | |
| @param Offset The operation register offset. | |
| @return The register content read. | |
| **/ | |
| UINT32 | |
| EFIAPI | |
| AhciReadReg ( | |
| IN EFI_PCI_IO_PROTOCOL *PciIo, | |
| IN UINT32 Offset | |
| ) | |
| { | |
| UINT32 Data; | |
| ASSERT (PciIo != NULL); | |
| Data = 0; | |
| PciIo->Mem.Read ( | |
| PciIo, | |
| EfiPciIoWidthUint32, | |
| AHCI_BAR_INDEX, | |
| (UINT64)Offset, | |
| 1, | |
| &Data | |
| ); | |
| return Data; | |
| } | |
| /** | |
| Write AHCI Operation register. | |
| @param PciIo The PCI IO protocol instance. | |
| @param Offset The operation register offset. | |
| @param Data The data used to write down. | |
| **/ | |
| VOID | |
| EFIAPI | |
| AhciWriteReg ( | |
| IN EFI_PCI_IO_PROTOCOL *PciIo, | |
| IN UINT32 Offset, | |
| IN UINT32 Data | |
| ) | |
| { | |
| ASSERT (PciIo != NULL); | |
| PciIo->Mem.Write ( | |
| PciIo, | |
| EfiPciIoWidthUint32, | |
| AHCI_BAR_INDEX, | |
| (UINT64)Offset, | |
| 1, | |
| &Data | |
| ); | |
| return; | |
| } | |
| /** | |
| This function is used to calculate the best PIO mode supported by specific IDE device | |
| @param IdentifyData The identify data of specific IDE device. | |
| @param DisPioMode Disqualified PIO modes collection. | |
| @param SelectedMode Available PIO modes collection. | |
| @retval EFI_SUCCESS Best PIO modes are returned. | |
| @retval EFI_UNSUPPORTED The device doesn't support PIO mode, | |
| or all supported modes have been disqualified. | |
| **/ | |
| EFI_STATUS | |
| CalculateBestPioMode ( | |
| IN EFI_IDENTIFY_DATA *IdentifyData, | |
| IN UINT16 *DisPioMode OPTIONAL, | |
| OUT UINT16 *SelectedMode | |
| ) | |
| { | |
| UINT16 PioMode; | |
| UINT16 AdvancedPioMode; | |
| UINT16 Temp; | |
| UINT16 Index; | |
| UINT16 MinimumPioCycleTime; | |
| Temp = 0xff; | |
| PioMode = (UINT8)(((ATA5_IDENTIFY_DATA *)(&(IdentifyData->AtaData)))->pio_cycle_timing >> 8); | |
| // | |
| // See whether Identify Data word 64 - 70 are valid | |
| // | |
| if ((IdentifyData->AtaData.field_validity & 0x02) == 0x02) { | |
| AdvancedPioMode = IdentifyData->AtaData.advanced_pio_modes; | |
| DEBUG ((DEBUG_INFO, "CalculateBestPioMode: AdvancedPioMode = %x\n", AdvancedPioMode)); | |
| for (Index = 0; Index < 8; Index++) { | |
| if ((AdvancedPioMode & 0x01) != 0) { | |
| Temp = Index; | |
| } | |
| AdvancedPioMode >>= 1; | |
| } | |
| // | |
| // If Temp is modified, mean the advanced_pio_modes is not zero; | |
| // if Temp is not modified, mean there is no advanced PIO mode supported, | |
| // the best PIO Mode is the value in pio_cycle_timing. | |
| // | |
| if (Temp != 0xff) { | |
| AdvancedPioMode = (UINT16)(Temp + 3); | |
| } else { | |
| AdvancedPioMode = PioMode; | |
| } | |
| // | |
| // Limit the PIO mode to at most PIO4. | |
| // | |
| PioMode = (UINT16)MIN (AdvancedPioMode, 4); | |
| MinimumPioCycleTime = IdentifyData->AtaData.min_pio_cycle_time_with_flow_control; | |
| if (MinimumPioCycleTime <= 120) { | |
| PioMode = (UINT16)MIN (4, PioMode); | |
| } else if (MinimumPioCycleTime <= 180) { | |
| PioMode = (UINT16)MIN (3, PioMode); | |
| } else if (MinimumPioCycleTime <= 240) { | |
| PioMode = (UINT16)MIN (2, PioMode); | |
| } else { | |
| PioMode = 0; | |
| } | |
| // | |
| // Degrade the PIO mode if the mode has been disqualified | |
| // | |
| if (DisPioMode != NULL) { | |
| if (*DisPioMode < 2) { | |
| return EFI_UNSUPPORTED; // no mode below ATA_PIO_MODE_BELOW_2 | |
| } | |
| if (PioMode >= *DisPioMode) { | |
| PioMode = (UINT16)(*DisPioMode - 1); | |
| } | |
| } | |
| if (PioMode < 2) { | |
| *SelectedMode = 1; // ATA_PIO_MODE_BELOW_2; | |
| } else { | |
| *SelectedMode = PioMode; // ATA_PIO_MODE_2 to ATA_PIO_MODE_4; | |
| } | |
| } else { | |
| // | |
| // Identify Data word 64 - 70 are not valid | |
| // Degrade the PIO mode if the mode has been disqualified | |
| // | |
| if (DisPioMode != NULL) { | |
| if (*DisPioMode < 2) { | |
| return EFI_UNSUPPORTED; // no mode below ATA_PIO_MODE_BELOW_2 | |
| } | |
| if (PioMode == *DisPioMode) { | |
| PioMode--; | |
| } | |
| } | |
| if (PioMode < 2) { | |
| *SelectedMode = 1; // ATA_PIO_MODE_BELOW_2; | |
| } else { | |
| *SelectedMode = 2; // ATA_PIO_MODE_2; | |
| } | |
| } | |
| return EFI_SUCCESS; | |
| } | |
| /** | |
| This function is used to calculate the best UDMA mode supported by specific IDE device | |
| @param IdentifyData The identify data of specific IDE device. | |
| @param DisUDmaMode Disqualified UDMA modes collection. | |
| @param SelectedMode Available UDMA modes collection. | |
| @retval EFI_SUCCESS Best UDMA modes are returned. | |
| @retval EFI_UNSUPPORTED The device doesn't support UDMA mode, | |
| or all supported modes have been disqualified. | |
| **/ | |
| EFI_STATUS | |
| CalculateBestUdmaMode ( | |
| IN EFI_IDENTIFY_DATA *IdentifyData, | |
| IN UINT16 *DisUDmaMode OPTIONAL, | |
| OUT UINT16 *SelectedMode | |
| ) | |
| { | |
| UINT16 TempMode; | |
| UINT16 DeviceUDmaMode; | |
| DeviceUDmaMode = 0; | |
| // | |
| // Check whether the WORD 88 (supported UltraDMA by drive) is valid | |
| // | |
| if ((IdentifyData->AtaData.field_validity & 0x04) == 0x00) { | |
| return EFI_UNSUPPORTED; | |
| } | |
| DeviceUDmaMode = IdentifyData->AtaData.ultra_dma_mode; | |
| DEBUG ((DEBUG_INFO, "CalculateBestUdmaMode: DeviceUDmaMode = %x\n", DeviceUDmaMode)); | |
| DeviceUDmaMode &= 0x3f; | |
| TempMode = 0; // initialize it to UDMA-0 | |
| while ((DeviceUDmaMode >>= 1) != 0) { | |
| TempMode++; | |
| } | |
| // | |
| // Degrade the UDMA mode if the mode has been disqualified | |
| // | |
| if (DisUDmaMode != NULL) { | |
| if (*DisUDmaMode == 0) { | |
| *SelectedMode = 0; | |
| return EFI_UNSUPPORTED; // no mode below ATA_UDMA_MODE_0 | |
| } | |
| if (TempMode >= *DisUDmaMode) { | |
| TempMode = (UINT16)(*DisUDmaMode - 1); | |
| } | |
| } | |
| // | |
| // Possible returned mode is between ATA_UDMA_MODE_0 and ATA_UDMA_MODE_5 | |
| // | |
| *SelectedMode = TempMode; | |
| return EFI_SUCCESS; | |
| } | |
| /** | |
| The Entry Point of module. It follows the standard UEFI driver model. | |
| @param[in] ImageHandle The firmware allocated handle for the EFI image. | |
| @param[in] SystemTable A pointer to the EFI System Table. | |
| @retval EFI_SUCCESS The entry point is executed successfully. | |
| @retval other Some error occurs when executing this entry point. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| InitializeSataControllerDriver ( | |
| IN EFI_HANDLE ImageHandle, | |
| IN EFI_SYSTEM_TABLE *SystemTable | |
| ) | |
| { | |
| EFI_STATUS Status; | |
| // | |
| // Install driver model protocol(s). | |
| // | |
| Status = EfiLibInstallDriverBindingComponentName2 ( | |
| ImageHandle, | |
| SystemTable, | |
| &gSataControllerDriverBinding, | |
| ImageHandle, | |
| &gSataControllerComponentName, | |
| &gSataControllerComponentName2 | |
| ); | |
| ASSERT_EFI_ERROR (Status); | |
| return Status; | |
| } | |
| /** | |
| Supported function of Driver Binding protocol for this driver. | |
| Test to see if this driver supports ControllerHandle. | |
| @param This Protocol instance pointer. | |
| @param Controller Handle of device to test. | |
| @param RemainingDevicePath A pointer to the device path. | |
| it should be ignored by device driver. | |
| @retval EFI_SUCCESS This driver supports this device. | |
| @retval EFI_ALREADY_STARTED This driver is already running on this device. | |
| @retval other This driver does not support this device. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| SataControllerSupported ( | |
| IN EFI_DRIVER_BINDING_PROTOCOL *This, | |
| IN EFI_HANDLE Controller, | |
| IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath | |
| ) | |
| { | |
| EFI_STATUS Status; | |
| EFI_PCI_IO_PROTOCOL *PciIo; | |
| PCI_TYPE00 PciData; | |
| // | |
| // Attempt to open PCI I/O Protocol | |
| // | |
| Status = gBS->OpenProtocol ( | |
| Controller, | |
| &gEfiPciIoProtocolGuid, | |
| (VOID **)&PciIo, | |
| This->DriverBindingHandle, | |
| Controller, | |
| EFI_OPEN_PROTOCOL_GET_PROTOCOL | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| // | |
| // Now further check the PCI header: Base Class (offset 0x0B) and | |
| // Sub Class (offset 0x0A). This controller should be an SATA controller | |
| // | |
| Status = PciIo->Pci.Read ( | |
| PciIo, | |
| EfiPciIoWidthUint8, | |
| PCI_CLASSCODE_OFFSET, | |
| sizeof (PciData.Hdr.ClassCode), | |
| PciData.Hdr.ClassCode | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| return EFI_UNSUPPORTED; | |
| } | |
| if (IS_PCI_IDE (&PciData) || IS_PCI_SATADPA (&PciData)) { | |
| return EFI_SUCCESS; | |
| } | |
| return EFI_UNSUPPORTED; | |
| } | |
| /** | |
| This routine is called right after the .Supported() called and | |
| Start this driver on ControllerHandle. | |
| @param This Protocol instance pointer. | |
| @param Controller Handle of device to bind driver to. | |
| @param RemainingDevicePath A pointer to the device path. | |
| it should be ignored by device driver. | |
| @retval EFI_SUCCESS This driver is added to this device. | |
| @retval EFI_ALREADY_STARTED This driver is already running on this device. | |
| @retval other Some error occurs when binding this driver to this device. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| SataControllerStart ( | |
| IN EFI_DRIVER_BINDING_PROTOCOL *This, | |
| IN EFI_HANDLE Controller, | |
| IN EFI_DEVICE_PATH_PROTOCOL *RemainingDevicePath | |
| ) | |
| { | |
| UINTN BailLogMask; | |
| EFI_STATUS Status; | |
| EFI_PCI_IO_PROTOCOL *PciIo; | |
| UINT64 OriginalPciAttributes; | |
| PCI_TYPE00 PciData; | |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; | |
| UINT32 Data32; | |
| UINTN ChannelDeviceCount; | |
| DEBUG ((DEBUG_INFO, "SataControllerStart START\n")); | |
| BailLogMask = DEBUG_ERROR; | |
| SataPrivateData = NULL; | |
| // | |
| // Now test and open PCI I/O Protocol | |
| // | |
| Status = gBS->OpenProtocol ( | |
| Controller, | |
| &gEfiPciIoProtocolGuid, | |
| (VOID **)&PciIo, | |
| This->DriverBindingHandle, | |
| Controller, | |
| EFI_OPEN_PROTOCOL_BY_DRIVER | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| if (Status == EFI_ALREADY_STARTED) { | |
| // | |
| // This is an expected condition for OpenProtocol() / BY_DRIVER, in a | |
| // DriverBindingStart() member function; degrade the log mask to | |
| // DEBUG_INFO. | |
| // | |
| BailLogMask = DEBUG_INFO; | |
| } | |
| goto Bail; | |
| } | |
| // | |
| // Save original PCI attributes, and enable IO space access, memory space | |
| // access, and Bus Master (DMA). | |
| // | |
| Status = PciIo->Attributes ( | |
| PciIo, | |
| EfiPciIoAttributeOperationGet, | |
| 0, | |
| &OriginalPciAttributes | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| goto ClosePciIo; | |
| } | |
| Status = PciIo->Attributes ( | |
| PciIo, | |
| EfiPciIoAttributeOperationEnable, | |
| EFI_PCI_DEVICE_ENABLE, | |
| NULL | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| goto ClosePciIo; | |
| } | |
| // | |
| // Allocate Sata Private Data structure | |
| // | |
| SataPrivateData = AllocateZeroPool (sizeof (EFI_SATA_CONTROLLER_PRIVATE_DATA)); | |
| if (SataPrivateData == NULL) { | |
| Status = EFI_OUT_OF_RESOURCES; | |
| goto RestorePciAttributes; | |
| } | |
| // | |
| // Initialize Sata Private Data | |
| // | |
| SataPrivateData->Signature = SATA_CONTROLLER_SIGNATURE; | |
| SataPrivateData->PciIo = PciIo; | |
| SataPrivateData->OriginalPciAttributes = OriginalPciAttributes; | |
| SataPrivateData->IdeInit.GetChannelInfo = IdeInitGetChannelInfo; | |
| SataPrivateData->IdeInit.NotifyPhase = IdeInitNotifyPhase; | |
| SataPrivateData->IdeInit.SubmitData = IdeInitSubmitData; | |
| SataPrivateData->IdeInit.DisqualifyMode = IdeInitDisqualifyMode; | |
| SataPrivateData->IdeInit.CalculateMode = IdeInitCalculateMode; | |
| SataPrivateData->IdeInit.SetTiming = IdeInitSetTiming; | |
| SataPrivateData->IdeInit.EnumAll = SATA_ENUMER_ALL; | |
| Status = PciIo->Pci.Read ( | |
| PciIo, | |
| EfiPciIoWidthUint8, | |
| PCI_CLASSCODE_OFFSET, | |
| sizeof (PciData.Hdr.ClassCode), | |
| PciData.Hdr.ClassCode | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| goto FreeSataPrivateData; | |
| } | |
| if (IS_PCI_IDE (&PciData)) { | |
| SataPrivateData->IdeInit.ChannelCount = IDE_MAX_CHANNEL; | |
| SataPrivateData->DeviceCount = IDE_MAX_DEVICES; | |
| } else if (IS_PCI_SATADPA (&PciData)) { | |
| // | |
| // Read Host Capability Register(CAP) to get Number of Ports(NPS) and Supports Port Multiplier(SPM) | |
| // NPS is 0's based value indicating the maximum number of ports supported by the HBA silicon. | |
| // A maximum of 32 ports can be supported. A value of '0h', indicating one port, is the minimum requirement. | |
| // | |
| Data32 = AhciReadReg (PciIo, R_AHCI_CAP); | |
| SataPrivateData->IdeInit.ChannelCount = (UINT8)((Data32 & B_AHCI_CAP_NPS) + 1); | |
| SataPrivateData->DeviceCount = AHCI_MAX_DEVICES; | |
| if ((Data32 & B_AHCI_CAP_SPM) == B_AHCI_CAP_SPM) { | |
| SataPrivateData->DeviceCount = AHCI_MULTI_MAX_DEVICES; | |
| } | |
| } | |
| ChannelDeviceCount = (UINTN)(SataPrivateData->IdeInit.ChannelCount) * (UINTN)(SataPrivateData->DeviceCount); | |
| SataPrivateData->DisqualifiedModes = AllocateZeroPool ((sizeof (EFI_ATA_COLLECTIVE_MODE)) * ChannelDeviceCount); | |
| if (SataPrivateData->DisqualifiedModes == NULL) { | |
| Status = EFI_OUT_OF_RESOURCES; | |
| goto FreeSataPrivateData; | |
| } | |
| SataPrivateData->IdentifyData = AllocateZeroPool ((sizeof (EFI_IDENTIFY_DATA)) * ChannelDeviceCount); | |
| if (SataPrivateData->IdentifyData == NULL) { | |
| Status = EFI_OUT_OF_RESOURCES; | |
| goto FreeDisqualifiedModes; | |
| } | |
| SataPrivateData->IdentifyValid = AllocateZeroPool ((sizeof (BOOLEAN)) * ChannelDeviceCount); | |
| if (SataPrivateData->IdentifyValid == NULL) { | |
| Status = EFI_OUT_OF_RESOURCES; | |
| goto FreeIdentifyData; | |
| } | |
| // | |
| // Install IDE Controller Init Protocol to this instance | |
| // | |
| Status = gBS->InstallMultipleProtocolInterfaces ( | |
| &Controller, | |
| &gEfiIdeControllerInitProtocolGuid, | |
| &(SataPrivateData->IdeInit), | |
| NULL | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| goto FreeIdentifyValid; | |
| } | |
| DEBUG ((DEBUG_INFO, "SataControllerStart END status = %r\n", Status)); | |
| return Status; | |
| FreeIdentifyValid: | |
| FreePool (SataPrivateData->IdentifyValid); | |
| FreeIdentifyData: | |
| FreePool (SataPrivateData->IdentifyData); | |
| FreeDisqualifiedModes: | |
| FreePool (SataPrivateData->DisqualifiedModes); | |
| FreeSataPrivateData: | |
| FreePool (SataPrivateData); | |
| RestorePciAttributes: | |
| PciIo->Attributes ( | |
| PciIo, | |
| EfiPciIoAttributeOperationSet, | |
| OriginalPciAttributes, | |
| NULL | |
| ); | |
| ClosePciIo: | |
| gBS->CloseProtocol ( | |
| Controller, | |
| &gEfiPciIoProtocolGuid, | |
| This->DriverBindingHandle, | |
| Controller | |
| ); | |
| Bail: | |
| DEBUG (( | |
| BailLogMask, | |
| "SataControllerStart error return status = %r\n", | |
| Status | |
| )); | |
| return Status; | |
| } | |
| /** | |
| Stop this driver on ControllerHandle. | |
| @param This Protocol instance pointer. | |
| @param Controller Handle of device to stop driver on. | |
| @param NumberOfChildren Not used. | |
| @param ChildHandleBuffer Not used. | |
| @retval EFI_SUCCESS This driver is removed from this device. | |
| @retval other Some error occurs when removing this driver from this device. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| SataControllerStop ( | |
| IN EFI_DRIVER_BINDING_PROTOCOL *This, | |
| IN EFI_HANDLE Controller, | |
| IN UINTN NumberOfChildren, | |
| IN EFI_HANDLE *ChildHandleBuffer | |
| ) | |
| { | |
| EFI_STATUS Status; | |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL *IdeInit; | |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; | |
| EFI_PCI_IO_PROTOCOL *PciIo; | |
| UINT64 OriginalPciAttributes; | |
| // | |
| // Open the produced protocol | |
| // | |
| Status = gBS->OpenProtocol ( | |
| Controller, | |
| &gEfiIdeControllerInitProtocolGuid, | |
| (VOID **)&IdeInit, | |
| This->DriverBindingHandle, | |
| Controller, | |
| EFI_OPEN_PROTOCOL_GET_PROTOCOL | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| return EFI_UNSUPPORTED; | |
| } | |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (IdeInit); | |
| ASSERT (SataPrivateData != NULL); | |
| PciIo = SataPrivateData->PciIo; | |
| OriginalPciAttributes = SataPrivateData->OriginalPciAttributes; | |
| // | |
| // Uninstall the IDE Controller Init Protocol from this instance | |
| // | |
| Status = gBS->UninstallMultipleProtocolInterfaces ( | |
| Controller, | |
| &gEfiIdeControllerInitProtocolGuid, | |
| &(SataPrivateData->IdeInit), | |
| NULL | |
| ); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| if (SataPrivateData->DisqualifiedModes != NULL) { | |
| FreePool (SataPrivateData->DisqualifiedModes); | |
| } | |
| if (SataPrivateData->IdentifyData != NULL) { | |
| FreePool (SataPrivateData->IdentifyData); | |
| } | |
| if (SataPrivateData->IdentifyValid != NULL) { | |
| FreePool (SataPrivateData->IdentifyValid); | |
| } | |
| FreePool (SataPrivateData); | |
| // | |
| // Restore original PCI attributes | |
| // | |
| PciIo->Attributes ( | |
| PciIo, | |
| EfiPciIoAttributeOperationSet, | |
| OriginalPciAttributes, | |
| NULL | |
| ); | |
| // | |
| // Close protocols opened by Sata Controller driver | |
| // | |
| return gBS->CloseProtocol ( | |
| Controller, | |
| &gEfiPciIoProtocolGuid, | |
| This->DriverBindingHandle, | |
| Controller | |
| ); | |
| } | |
| /** | |
| Calculate the flat array subscript of a (Channel, Device) pair. | |
| @param[in] SataPrivateData The private data structure corresponding to the | |
| SATA controller that attaches the device for | |
| which the flat array subscript is being | |
| calculated. | |
| @param[in] Channel The channel (ie. port) number on the SATA | |
| controller that the device is attached to. | |
| @param[in] Device The device number on the channel. | |
| @return The flat array subscript suitable for indexing DisqualifiedModes, | |
| IdentifyData, and IdentifyValid. | |
| **/ | |
| STATIC | |
| UINTN | |
| FlatDeviceIndex ( | |
| IN CONST EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData, | |
| IN UINTN Channel, | |
| IN UINTN Device | |
| ) | |
| { | |
| ASSERT (SataPrivateData != NULL); | |
| ASSERT (Channel < SataPrivateData->IdeInit.ChannelCount); | |
| ASSERT (Device < SataPrivateData->DeviceCount); | |
| return Channel * SataPrivateData->DeviceCount + Device; | |
| } | |
| // | |
| // Interface functions of IDE_CONTROLLER_INIT protocol | |
| // | |
| /** | |
| Returns the information about the specified IDE channel. | |
| This function can be used to obtain information about a particular IDE channel. | |
| The driver entity uses this information during the enumeration process. | |
| If Enabled is set to FALSE, the driver entity will not scan the channel. Note | |
| that it will not prevent an operating system driver from scanning the channel. | |
| For most of today's controllers, MaxDevices will either be 1 or 2. For SATA | |
| controllers, this value will always be 1. SATA configurations can contain SATA | |
| port multipliers. SATA port multipliers behave like SATA bridges and can support | |
| up to 16 devices on the other side. If a SATA port out of the IDE controller | |
| is connected to a port multiplier, MaxDevices will be set to the number of SATA | |
| devices that the port multiplier supports. Because today's port multipliers | |
| support up to fifteen SATA devices, this number can be as large as fifteen. The IDE | |
| bus driver is required to scan for the presence of port multipliers behind an SATA | |
| controller and enumerate up to MaxDevices number of devices behind the port | |
| multiplier. | |
| In this context, the devices behind a port multiplier constitute a channel. | |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. | |
| @param[in] Channel Zero-based channel number. | |
| @param[out] Enabled TRUE if this channel is enabled. Disabled channels | |
| are not scanned to see if any devices are present. | |
| @param[out] MaxDevices The maximum number of IDE devices that the bus driver | |
| can expect on this channel. For the ATA/ATAPI | |
| specification, version 6, this number will either be | |
| one or two. For Serial ATA (SATA) configurations with a | |
| port multiplier, this number can be as large as fifteen. | |
| @retval EFI_SUCCESS Information was returned without any errors. | |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| IdeInitGetChannelInfo ( | |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, | |
| IN UINT8 Channel, | |
| OUT BOOLEAN *Enabled, | |
| OUT UINT8 *MaxDevices | |
| ) | |
| { | |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; | |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); | |
| ASSERT (SataPrivateData != NULL); | |
| if (Channel < This->ChannelCount) { | |
| *Enabled = TRUE; | |
| *MaxDevices = SataPrivateData->DeviceCount; | |
| return EFI_SUCCESS; | |
| } | |
| *Enabled = FALSE; | |
| return EFI_INVALID_PARAMETER; | |
| } | |
| /** | |
| The notifications from the driver entity that it is about to enter a certain | |
| phase of the IDE channel enumeration process. | |
| This function can be used to notify the IDE controller driver to perform | |
| specific actions, including any chipset-specific initialization, so that the | |
| chipset is ready to enter the next phase. Seven notification points are defined | |
| at this time. | |
| More synchronization points may be added as required in the future. | |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. | |
| @param[in] Phase The phase during enumeration. | |
| @param[in] Channel Zero-based channel number. | |
| @retval EFI_SUCCESS The notification was accepted without any errors. | |
| @retval EFI_UNSUPPORTED Phase is not supported. | |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). | |
| @retval EFI_NOT_READY This phase cannot be entered at this time; for | |
| example, an attempt was made to enter a Phase | |
| without having entered one or more previous | |
| Phase. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| IdeInitNotifyPhase ( | |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, | |
| IN EFI_IDE_CONTROLLER_ENUM_PHASE Phase, | |
| IN UINT8 Channel | |
| ) | |
| { | |
| return EFI_SUCCESS; | |
| } | |
| /** | |
| Submits the device information to the IDE controller driver. | |
| This function is used by the driver entity to pass detailed information about | |
| a particular device to the IDE controller driver. The driver entity obtains | |
| this information by issuing an ATA or ATAPI IDENTIFY_DEVICE command. IdentifyData | |
| is the pointer to the response data buffer. The IdentifyData buffer is owned | |
| by the driver entity, and the IDE controller driver must make a local copy | |
| of the entire buffer or parts of the buffer as needed. The original IdentifyData | |
| buffer pointer may not be valid when | |
| - EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() or | |
| - EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() is called at a later point. | |
| The IDE controller driver may consult various fields of EFI_IDENTIFY_DATA to | |
| compute the optimum mode for the device. These fields are not limited to the | |
| timing information. For example, an implementation of the IDE controller driver | |
| may examine the vendor and type/mode field to match known bad drives. | |
| The driver entity may submit drive information in any order, as long as it | |
| submits information for all the devices belonging to the enumeration group | |
| before EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() is called for any device | |
| in that enumeration group. If a device is absent, EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() | |
| should be called with IdentifyData set to NULL. The IDE controller driver may | |
| not have any other mechanism to know whether a device is present or not. Therefore, | |
| setting IdentifyData to NULL does not constitute an error condition. | |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() can be called only once for a | |
| given (Channel, Device) pair. | |
| @param[in] This A pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. | |
| @param[in] Channel Zero-based channel number. | |
| @param[in] Device Zero-based device number on the Channel. | |
| @param[in] IdentifyData The device's response to the ATA IDENTIFY_DEVICE command. | |
| @retval EFI_SUCCESS The information was accepted without any errors. | |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). | |
| @retval EFI_INVALID_PARAMETER Device is invalid. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| IdeInitSubmitData ( | |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, | |
| IN UINT8 Channel, | |
| IN UINT8 Device, | |
| IN EFI_IDENTIFY_DATA *IdentifyData | |
| ) | |
| { | |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; | |
| UINTN DeviceIndex; | |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); | |
| ASSERT (SataPrivateData != NULL); | |
| if ((Channel >= This->ChannelCount) || (Device >= SataPrivateData->DeviceCount)) { | |
| return EFI_INVALID_PARAMETER; | |
| } | |
| DeviceIndex = FlatDeviceIndex (SataPrivateData, Channel, Device); | |
| // | |
| // Make a local copy of device's IdentifyData and mark the valid flag | |
| // | |
| if (IdentifyData != NULL) { | |
| CopyMem ( | |
| &(SataPrivateData->IdentifyData[DeviceIndex]), | |
| IdentifyData, | |
| sizeof (EFI_IDENTIFY_DATA) | |
| ); | |
| SataPrivateData->IdentifyValid[DeviceIndex] = TRUE; | |
| } else { | |
| SataPrivateData->IdentifyValid[DeviceIndex] = FALSE; | |
| } | |
| return EFI_SUCCESS; | |
| } | |
| /** | |
| Disqualifies specific modes for an IDE device. | |
| This function allows the driver entity or other drivers (such as platform | |
| drivers) to reject certain timing modes and request the IDE controller driver | |
| to recalculate modes. This function allows the driver entity and the IDE | |
| controller driver to negotiate the timings on a per-device basis. This function | |
| is useful in the case of drives that lie about their capabilities. An example | |
| is when the IDE device fails to accept the timing modes that are calculated | |
| by the IDE controller driver based on the response to the Identify Drive command. | |
| If the driver entity does not want to limit the ATA timing modes and leave that | |
| decision to the IDE controller driver, it can either not call this function for | |
| the given device or call this function and set the Valid flag to FALSE for all | |
| modes that are listed in EFI_ATA_COLLECTIVE_MODE. | |
| The driver entity may disqualify modes for a device in any order and any number | |
| of times. | |
| This function can be called multiple times to invalidate multiple modes of the | |
| same type (e.g., Programmed Input/Output [PIO] modes 3 and 4). See the ATA/ATAPI | |
| specification for more information on PIO modes. | |
| For Serial ATA (SATA) controllers, this member function can be used to disqualify | |
| a higher transfer rate mode on a given channel. For example, a platform driver | |
| may inform the IDE controller driver to not use second-generation (Gen2) speeds | |
| for a certain SATA drive. | |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. | |
| @param[in] Channel The zero-based channel number. | |
| @param[in] Device The zero-based device number on the Channel. | |
| @param[in] BadModes The modes that the device does not support and that | |
| should be disqualified. | |
| @retval EFI_SUCCESS The modes were accepted without any errors. | |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). | |
| @retval EFI_INVALID_PARAMETER Device is invalid. | |
| @retval EFI_INVALID_PARAMETER IdentifyData is NULL. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| IdeInitDisqualifyMode ( | |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, | |
| IN UINT8 Channel, | |
| IN UINT8 Device, | |
| IN EFI_ATA_COLLECTIVE_MODE *BadModes | |
| ) | |
| { | |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; | |
| UINTN DeviceIndex; | |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); | |
| ASSERT (SataPrivateData != NULL); | |
| if ((Channel >= This->ChannelCount) || (BadModes == NULL) || (Device >= SataPrivateData->DeviceCount)) { | |
| return EFI_INVALID_PARAMETER; | |
| } | |
| DeviceIndex = FlatDeviceIndex (SataPrivateData, Channel, Device); | |
| // | |
| // Record the disqualified modes per channel per device. From ATA/ATAPI spec, | |
| // if a mode is not supported, the modes higher than it is also not supported. | |
| // | |
| CopyMem ( | |
| &(SataPrivateData->DisqualifiedModes[DeviceIndex]), | |
| BadModes, | |
| sizeof (EFI_ATA_COLLECTIVE_MODE) | |
| ); | |
| return EFI_SUCCESS; | |
| } | |
| /** | |
| Returns the information about the optimum modes for the specified IDE device. | |
| This function is used by the driver entity to obtain the optimum ATA modes for | |
| a specific device. The IDE controller driver takes into account the following | |
| while calculating the mode: | |
| - The IdentifyData inputs to EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() | |
| - The BadModes inputs to EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() | |
| The driver entity is required to call EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() | |
| for all the devices that belong to an enumeration group before calling | |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.CalculateMode() for any device in the same group. | |
| The IDE controller driver will use controller- and possibly platform-specific | |
| algorithms to arrive at SupportedModes. The IDE controller may base its | |
| decision on user preferences and other considerations as well. This function | |
| may be called multiple times because the driver entity may renegotiate the mode | |
| with the IDE controller driver using EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode(). | |
| The driver entity may collect timing information for various devices in any | |
| order. The driver entity is responsible for making sure that all the dependencies | |
| are satisfied. For example, the SupportedModes information for device A that | |
| was previously returned may become stale after a call to | |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyMode() for device B. | |
| The buffer SupportedModes is allocated by the callee because the caller does | |
| not necessarily know the size of the buffer. The type EFI_ATA_COLLECTIVE_MODE | |
| is defined in a way that allows for future extensibility and can be of variable | |
| length. This memory pool should be deallocated by the caller when it is no | |
| longer necessary. | |
| The IDE controller driver for a Serial ATA (SATA) controller can use this | |
| member function to force a lower speed (first-generation [Gen1] speeds on a | |
| second-generation [Gen2]-capable hardware). The IDE controller driver can | |
| also allow the driver entity to stay with the speed that has been negotiated | |
| by the physical layer. | |
| @param[in] This The pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. | |
| @param[in] Channel A zero-based channel number. | |
| @param[in] Device A zero-based device number on the Channel. | |
| @param[out] SupportedModes The optimum modes for the device. | |
| @retval EFI_SUCCESS SupportedModes was returned. | |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). | |
| @retval EFI_INVALID_PARAMETER Device is invalid. | |
| @retval EFI_INVALID_PARAMETER SupportedModes is NULL. | |
| @retval EFI_NOT_READY Modes cannot be calculated due to a lack of | |
| data. This error may happen if | |
| EFI_IDE_CONTROLLER_INIT_PROTOCOL.SubmitData() | |
| and EFI_IDE_CONTROLLER_INIT_PROTOCOL.DisqualifyData() | |
| were not called for at least one drive in the | |
| same enumeration group. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| IdeInitCalculateMode ( | |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, | |
| IN UINT8 Channel, | |
| IN UINT8 Device, | |
| OUT EFI_ATA_COLLECTIVE_MODE **SupportedModes | |
| ) | |
| { | |
| EFI_SATA_CONTROLLER_PRIVATE_DATA *SataPrivateData; | |
| EFI_IDENTIFY_DATA *IdentifyData; | |
| BOOLEAN IdentifyValid; | |
| EFI_ATA_COLLECTIVE_MODE *DisqualifiedModes; | |
| UINT16 SelectedMode; | |
| EFI_STATUS Status; | |
| UINTN DeviceIndex; | |
| SataPrivateData = SATA_CONTROLLER_PRIVATE_DATA_FROM_THIS (This); | |
| ASSERT (SataPrivateData != NULL); | |
| if ((Channel >= This->ChannelCount) || (SupportedModes == NULL) || (Device >= SataPrivateData->DeviceCount)) { | |
| return EFI_INVALID_PARAMETER; | |
| } | |
| *SupportedModes = AllocateZeroPool (sizeof (EFI_ATA_COLLECTIVE_MODE)); | |
| if (*SupportedModes == NULL) { | |
| ASSERT (*SupportedModes != NULL); | |
| return EFI_OUT_OF_RESOURCES; | |
| } | |
| DeviceIndex = FlatDeviceIndex (SataPrivateData, Channel, Device); | |
| IdentifyData = &(SataPrivateData->IdentifyData[DeviceIndex]); | |
| IdentifyValid = SataPrivateData->IdentifyValid[DeviceIndex]; | |
| DisqualifiedModes = &(SataPrivateData->DisqualifiedModes[DeviceIndex]); | |
| // | |
| // Make sure we've got the valid identify data of the device from SubmitData() | |
| // | |
| if (!IdentifyValid) { | |
| FreePool (*SupportedModes); | |
| return EFI_NOT_READY; | |
| } | |
| Status = CalculateBestPioMode ( | |
| IdentifyData, | |
| (DisqualifiedModes->PioMode.Valid ? ((UINT16 *)&(DisqualifiedModes->PioMode.Mode)) : NULL), | |
| &SelectedMode | |
| ); | |
| if (!EFI_ERROR (Status)) { | |
| (*SupportedModes)->PioMode.Valid = TRUE; | |
| (*SupportedModes)->PioMode.Mode = SelectedMode; | |
| } else { | |
| (*SupportedModes)->PioMode.Valid = FALSE; | |
| } | |
| DEBUG ((DEBUG_INFO, "IdeInitCalculateMode: PioMode = %x\n", (*SupportedModes)->PioMode.Mode)); | |
| Status = CalculateBestUdmaMode ( | |
| IdentifyData, | |
| (DisqualifiedModes->UdmaMode.Valid ? ((UINT16 *)&(DisqualifiedModes->UdmaMode.Mode)) : NULL), | |
| &SelectedMode | |
| ); | |
| if (!EFI_ERROR (Status)) { | |
| (*SupportedModes)->UdmaMode.Valid = TRUE; | |
| (*SupportedModes)->UdmaMode.Mode = SelectedMode; | |
| } else { | |
| (*SupportedModes)->UdmaMode.Valid = FALSE; | |
| } | |
| DEBUG ((DEBUG_INFO, "IdeInitCalculateMode: UdmaMode = %x\n", (*SupportedModes)->UdmaMode.Mode)); | |
| // | |
| // The modes other than PIO and UDMA are not supported | |
| // | |
| return EFI_SUCCESS; | |
| } | |
| /** | |
| Commands the IDE controller driver to program the IDE controller hardware | |
| so that the specified device can operate at the specified mode. | |
| This function is used by the driver entity to instruct the IDE controller | |
| driver to program the IDE controller hardware to the specified modes. This | |
| function can be called only once for a particular device. For a Serial ATA | |
| (SATA) Advanced Host Controller Interface (AHCI) controller, no controller- | |
| specific programming may be required. | |
| @param[in] This Pointer to the EFI_IDE_CONTROLLER_INIT_PROTOCOL instance. | |
| @param[in] Channel Zero-based channel number. | |
| @param[in] Device Zero-based device number on the Channel. | |
| @param[in] Modes The modes to set. | |
| @retval EFI_SUCCESS The command was accepted without any errors. | |
| @retval EFI_INVALID_PARAMETER Channel is invalid (Channel >= ChannelCount). | |
| @retval EFI_INVALID_PARAMETER Device is invalid. | |
| @retval EFI_NOT_READY Modes cannot be set at this time due to lack of data. | |
| @retval EFI_DEVICE_ERROR Modes cannot be set due to hardware failure. | |
| The driver entity should not use this device. | |
| **/ | |
| EFI_STATUS | |
| EFIAPI | |
| IdeInitSetTiming ( | |
| IN EFI_IDE_CONTROLLER_INIT_PROTOCOL *This, | |
| IN UINT8 Channel, | |
| IN UINT8 Device, | |
| IN EFI_ATA_COLLECTIVE_MODE *Modes | |
| ) | |
| { | |
| return EFI_SUCCESS; | |
| } |