| /** @file | |
| EFI_USB2_HC_PROTOCOL as defined in UEFI 2.0. | |
| The USB Host Controller Protocol is used by code, typically USB bus drivers, | |
| running in the EFI boot services environment, to perform data transactions over | |
| a USB bus. In addition, it provides an abstraction for the root hub of the USB bus. | |
| Copyright (c) 2006 - 2018, Intel Corporation. All rights reserved.<BR> | |
| SPDX-License-Identifier: BSD-2-Clause-Patent | |
| **/ | |
| #ifndef _USB2_HOSTCONTROLLER_H_ | |
| #define _USB2_HOSTCONTROLLER_H_ | |
| #include <Protocol/UsbIo.h> | |
| #define EFI_USB2_HC_PROTOCOL_GUID \ | |
| { \ | |
| 0x3e745226, 0x9818, 0x45b6, {0xa2, 0xac, 0xd7, 0xcd, 0xe, 0x8b, 0xa2, 0xbc } \ | |
| } | |
| /// | |
| /// Forward reference for pure ANSI compatability | |
| /// | |
| typedef struct _EFI_USB2_HC_PROTOCOL EFI_USB2_HC_PROTOCOL; | |
| typedef struct { | |
| UINT16 PortStatus; ///< Contains current port status bitmap. | |
| UINT16 PortChangeStatus; ///< Contains current port status change bitmap. | |
| } EFI_USB_PORT_STATUS; | |
| /// | |
| /// EFI_USB_PORT_STATUS.PortStatus bit definition | |
| /// | |
| #define USB_PORT_STAT_CONNECTION 0x0001 | |
| #define USB_PORT_STAT_ENABLE 0x0002 | |
| #define USB_PORT_STAT_SUSPEND 0x0004 | |
| #define USB_PORT_STAT_OVERCURRENT 0x0008 | |
| #define USB_PORT_STAT_RESET 0x0010 | |
| #define USB_PORT_STAT_POWER 0x0100 | |
| #define USB_PORT_STAT_LOW_SPEED 0x0200 | |
| #define USB_PORT_STAT_HIGH_SPEED 0x0400 | |
| #define USB_PORT_STAT_SUPER_SPEED 0x0800 | |
| #define USB_PORT_STAT_OWNER 0x2000 | |
| /// | |
| /// EFI_USB_PORT_STATUS.PortChangeStatus bit definition | |
| /// | |
| #define USB_PORT_STAT_C_CONNECTION 0x0001 | |
| #define USB_PORT_STAT_C_ENABLE 0x0002 | |
| #define USB_PORT_STAT_C_SUSPEND 0x0004 | |
| #define USB_PORT_STAT_C_OVERCURRENT 0x0008 | |
| #define USB_PORT_STAT_C_RESET 0x0010 | |
| /// | |
| /// Usb port features value | |
| /// Each value indicates its bit index in the port status and status change bitmaps, | |
| /// if combines these two bitmaps into a 32-bit bitmap. | |
| /// | |
| typedef enum { | |
| EfiUsbPortEnable = 1, | |
| EfiUsbPortSuspend = 2, | |
| EfiUsbPortReset = 4, | |
| EfiUsbPortPower = 8, | |
| EfiUsbPortOwner = 13, | |
| EfiUsbPortConnectChange = 16, | |
| EfiUsbPortEnableChange = 17, | |
| EfiUsbPortSuspendChange = 18, | |
| EfiUsbPortOverCurrentChange = 19, | |
| EfiUsbPortResetChange = 20 | |
| } EFI_USB_PORT_FEATURE; | |
| #define EFI_USB_SPEED_FULL 0x0000 ///< 12 Mb/s, USB 1.1 OHCI and UHCI HC. | |
| #define EFI_USB_SPEED_LOW 0x0001 ///< 1 Mb/s, USB 1.1 OHCI and UHCI HC. | |
| #define EFI_USB_SPEED_HIGH 0x0002 ///< 480 Mb/s, USB 2.0 EHCI HC. | |
| #define EFI_USB_SPEED_SUPER 0x0003 ///< 4.8 Gb/s, USB 3.0 XHCI HC. | |
| typedef struct { | |
| UINT8 TranslatorHubAddress; ///< device address | |
| UINT8 TranslatorPortNumber; ///< the port number of the hub that device is connected to. | |
| } EFI_USB2_HC_TRANSACTION_TRANSLATOR; | |
| // | |
| // Protocol definitions | |
| // | |
| /** | |
| Retrieves the Host Controller capabilities. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param MaxSpeed Host controller data transfer speed. | |
| @param PortNumber Number of the root hub ports. | |
| @param Is64BitCapable TRUE if controller supports 64-bit memory addressing, | |
| FALSE otherwise. | |
| @retval EFI_SUCCESS The host controller capabilities were retrieved successfully. | |
| @retval EFI_INVALID_PARAMETER One of the input args was NULL. | |
| @retval EFI_DEVICE_ERROR An error was encountered while attempting to | |
| retrieve the capabilities. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_GET_CAPABILITY)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| OUT UINT8 *MaxSpeed, | |
| OUT UINT8 *PortNumber, | |
| OUT UINT8 *Is64BitCapable | |
| ); | |
| #define EFI_USB_HC_RESET_GLOBAL 0x0001 | |
| #define EFI_USB_HC_RESET_HOST_CONTROLLER 0x0002 | |
| #define EFI_USB_HC_RESET_GLOBAL_WITH_DEBUG 0x0004 | |
| #define EFI_USB_HC_RESET_HOST_WITH_DEBUG 0x0008 | |
| /** | |
| Provides software reset for the USB host controller. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param Attributes A bit mask of the reset operation to perform. | |
| @retval EFI_SUCCESS The reset operation succeeded. | |
| @retval EFI_INVALID_PARAMETER Attributes is not valid. | |
| @retval EFI_UNSUPPORTED The type of reset specified by Attributes is not currently | |
| supported by the host controller hardware. | |
| @retval EFI_ACCESS_DENIED Reset operation is rejected due to the debug port being configured | |
| and active; only EFI_USB_HC_RESET_GLOBAL_WITH_DEBUG or | |
| EFI_USB_HC_RESET_HOST_WITH_DEBUG reset Attributes can be used to | |
| perform reset operation for this host controller. | |
| @retval EFI_DEVICE_ERROR An error was encountered while attempting to | |
| retrieve the capabilities. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_RESET)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT16 Attributes | |
| ); | |
| /** | |
| Enumration value for status of USB HC. | |
| **/ | |
| typedef enum { | |
| EfiUsbHcStateHalt, ///< The host controller is in halt | |
| ///< state. No USB transactions can occur | |
| ///< while in this state. The host | |
| ///< controller can enter this state for | |
| ///< three reasons: 1) After host | |
| ///< controller hardware reset. 2) | |
| ///< Explicitly set by software. 3) | |
| ///< Triggered by a fatal error such as | |
| ///< consistency check failure. | |
| EfiUsbHcStateOperational, ///< The host controller is in an | |
| ///< operational state. When in | |
| ///< this state, the host | |
| ///< controller can execute bus | |
| ///< traffic. This state must be | |
| ///< explicitly set to enable the | |
| ///< USB bus traffic. | |
| EfiUsbHcStateSuspend, ///< The host controller is in the | |
| ///< suspend state. No USB | |
| ///< transactions can occur while in | |
| ///< this state. The host controller | |
| ///< enters this state for the | |
| ///< following reasons: 1) Explicitly | |
| ///< set by software. 2) Triggered | |
| ///< when there is no bus traffic for | |
| ///< 3 microseconds. | |
| EfiUsbHcStateMaximum ///< Maximum value for enumration value of HC status. | |
| } EFI_USB_HC_STATE; | |
| /** | |
| Retrieves current state of the USB host controller. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param State A pointer to the EFI_USB_HC_STATE data structure that | |
| indicates current state of the USB host controller. | |
| @retval EFI_SUCCESS The state information of the host controller was returned in State. | |
| @retval EFI_INVALID_PARAMETER State is NULL. | |
| @retval EFI_DEVICE_ERROR An error was encountered while attempting to retrieve the | |
| host controller's current state. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_GET_STATE)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| OUT EFI_USB_HC_STATE *State | |
| ); | |
| /** | |
| Sets the USB host controller to a specific state. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param State Indicates the state of the host controller that will be set. | |
| @retval EFI_SUCCESS The USB host controller was successfully placed in the state | |
| specified by State. | |
| @retval EFI_INVALID_PARAMETER State is not valid. | |
| @retval EFI_DEVICE_ERROR Failed to set the state specified by State due to device error. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_SET_STATE)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN EFI_USB_HC_STATE State | |
| ); | |
| /** | |
| Submits control transfer to a target USB device. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param DeviceAddress Represents the address of the target device on the USB. | |
| @param DeviceSpeed Indicates device speed. | |
| @param MaximumPacketLength Indicates the maximum packet size that the default control transfer | |
| endpoint is capable of sending or receiving. | |
| @param Request A pointer to the USB device request that will be sent to the USB device. | |
| @param TransferDirection Specifies the data direction for the transfer. There are three values | |
| available, EfiUsbDataIn, EfiUsbDataOut and EfiUsbNoData. | |
| @param Data A pointer to the buffer of data that will be transmitted to USB device or | |
| received from USB device. | |
| @param DataLength On input, indicates the size, in bytes, of the data buffer specified by Data. | |
| On output, indicates the amount of data actually transferred. | |
| @param TimeOut Indicates the maximum time, in milliseconds, which the transfer is | |
| allowed to complete. | |
| @param Translator A pointer to the transaction translator data. | |
| @param TransferResult A pointer to the detailed result information generated by this control | |
| transfer. | |
| @retval EFI_SUCCESS The control transfer was completed successfully. | |
| @retval EFI_INVALID_PARAMETER Some parameters are invalid. | |
| @retval EFI_OUT_OF_RESOURCES The control transfer could not be completed due to a lack of resources. | |
| @retval EFI_TIMEOUT The control transfer failed due to timeout. | |
| @retval EFI_DEVICE_ERROR The control transfer failed due to host controller or device error. | |
| Caller should check TransferResult for detailed error information. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_CONTROL_TRANSFER)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 DeviceAddress, | |
| IN UINT8 DeviceSpeed, | |
| IN UINTN MaximumPacketLength, | |
| IN EFI_USB_DEVICE_REQUEST *Request, | |
| IN EFI_USB_DATA_DIRECTION TransferDirection, | |
| IN OUT VOID *Data OPTIONAL, | |
| IN OUT UINTN *DataLength OPTIONAL, | |
| IN UINTN TimeOut, | |
| IN EFI_USB2_HC_TRANSACTION_TRANSLATOR *Translator, | |
| OUT UINT32 *TransferResult | |
| ); | |
| #define EFI_USB_MAX_BULK_BUFFER_NUM 10 | |
| /** | |
| Submits bulk transfer to a bulk endpoint of a USB device. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param DeviceAddress Represents the address of the target device on the USB. | |
| @param EndPointAddress The combination of an endpoint number and an endpoint direction of the | |
| target USB device. | |
| @param DeviceSpeed Indicates device speed. | |
| @param MaximumPacketLength Indicates the maximum packet size the target endpoint is capable of | |
| sending or receiving. | |
| @param DataBuffersNumber Number of data buffers prepared for the transfer. | |
| @param Data Array of pointers to the buffers of data that will be transmitted to USB | |
| device or received from USB device. | |
| @param DataLength When input, indicates the size, in bytes, of the data buffers specified by | |
| Data. When output, indicates the actually transferred data size. | |
| @param DataToggle A pointer to the data toggle value. | |
| @param TimeOut Indicates the maximum time, in milliseconds, which the transfer is | |
| allowed to complete. | |
| @param Translator A pointer to the transaction translator data. | |
| @param TransferResult A pointer to the detailed result information of the bulk transfer. | |
| @retval EFI_SUCCESS The bulk transfer was completed successfully. | |
| @retval EFI_INVALID_PARAMETER Some parameters are invalid. | |
| @retval EFI_OUT_OF_RESOURCES The bulk transfer could not be submitted due to a lack of resources. | |
| @retval EFI_TIMEOUT The bulk transfer failed due to timeout. | |
| @retval EFI_DEVICE_ERROR The bulk transfer failed due to host controller or device error. | |
| Caller should check TransferResult for detailed error information. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_BULK_TRANSFER)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 DeviceAddress, | |
| IN UINT8 EndPointAddress, | |
| IN UINT8 DeviceSpeed, | |
| IN UINTN MaximumPacketLength, | |
| IN UINT8 DataBuffersNumber, | |
| IN OUT VOID *Data[EFI_USB_MAX_BULK_BUFFER_NUM], | |
| IN OUT UINTN *DataLength, | |
| IN OUT UINT8 *DataToggle, | |
| IN UINTN TimeOut, | |
| IN EFI_USB2_HC_TRANSACTION_TRANSLATOR *Translator, | |
| OUT UINT32 *TransferResult | |
| ); | |
| /** | |
| Submits an asynchronous interrupt transfer to an interrupt endpoint of a USB device. | |
| Translator parameter doesn't exist in UEFI2.0 spec, but it will be updated in the following specification version. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param DeviceAddress Represents the address of the target device on the USB. | |
| @param EndPointAddress The combination of an endpoint number and an endpoint direction of the | |
| target USB device. | |
| @param DeviceSpeed Indicates device speed. | |
| @param MaximumPacketLength Indicates the maximum packet size the target endpoint is capable of | |
| sending or receiving. | |
| @param IsNewTransfer If TRUE, an asynchronous interrupt pipe is built between the host and the | |
| target interrupt endpoint. If FALSE, the specified asynchronous interrupt | |
| pipe is canceled. If TRUE, and an interrupt transfer exists for the target | |
| end point, then EFI_INVALID_PARAMETER is returned. | |
| @param DataToggle A pointer to the data toggle value. | |
| @param PollingInterval Indicates the interval, in milliseconds, that the asynchronous interrupt | |
| transfer is polled. | |
| @param DataLength Indicates the length of data to be received at the rate specified by | |
| PollingInterval from the target asynchronous interrupt endpoint. | |
| @param Translator A pointr to the transaction translator data. | |
| @param CallBackFunction The Callback function. This function is called at the rate specified by | |
| PollingInterval. | |
| @param Context The context that is passed to the CallBackFunction. This is an | |
| optional parameter and may be NULL. | |
| @retval EFI_SUCCESS The asynchronous interrupt transfer request has been successfully | |
| submitted or canceled. | |
| @retval EFI_INVALID_PARAMETER Some parameters are invalid. | |
| @retval EFI_OUT_OF_RESOURCES The request could not be completed due to a lack of resources. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_ASYNC_INTERRUPT_TRANSFER)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 DeviceAddress, | |
| IN UINT8 EndPointAddress, | |
| IN UINT8 DeviceSpeed, | |
| IN UINTN MaxiumPacketLength, | |
| IN BOOLEAN IsNewTransfer, | |
| IN OUT UINT8 *DataToggle, | |
| IN UINTN PollingInterval OPTIONAL, | |
| IN UINTN DataLength OPTIONAL, | |
| IN EFI_USB2_HC_TRANSACTION_TRANSLATOR *Translator OPTIONAL, | |
| IN EFI_ASYNC_USB_TRANSFER_CALLBACK CallBackFunction OPTIONAL, | |
| IN VOID *Context OPTIONAL | |
| ); | |
| /** | |
| Submits synchronous interrupt transfer to an interrupt endpoint of a USB device. | |
| Translator parameter doesn't exist in UEFI2.0 spec, but it will be updated in the following specification version. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param DeviceAddress Represents the address of the target device on the USB. | |
| @param EndPointAddress The combination of an endpoint number and an endpoint direction of the | |
| target USB device. | |
| @param DeviceSpeed Indicates device speed. | |
| @param MaximumPacketLength Indicates the maximum packet size the target endpoint is capable of | |
| sending or receiving. | |
| @param Data A pointer to the buffer of data that will be transmitted to USB device or | |
| received from USB device. | |
| @param DataLength On input, the size, in bytes, of the data buffer specified by Data. On | |
| output, the number of bytes transferred. | |
| @param DataToggle A pointer to the data toggle value. | |
| @param TimeOut Indicates the maximum time, in milliseconds, which the transfer is | |
| allowed to complete. | |
| @param Translator A pointr to the transaction translator data. | |
| @param TransferResult A pointer to the detailed result information from the synchronous | |
| interrupt transfer. | |
| @retval EFI_SUCCESS The synchronous interrupt transfer was completed successfully. | |
| @retval EFI_INVALID_PARAMETER Some parameters are invalid. | |
| @retval EFI_OUT_OF_RESOURCES The synchronous interrupt transfer could not be submitted due to a lack of resources. | |
| @retval EFI_TIMEOUT The synchronous interrupt transfer failed due to timeout. | |
| @retval EFI_DEVICE_ERROR The synchronous interrupt transfer failed due to host controller or device error. | |
| Caller should check TransferResult for detailed error information. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_SYNC_INTERRUPT_TRANSFER)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 DeviceAddress, | |
| IN UINT8 EndPointAddress, | |
| IN UINT8 DeviceSpeed, | |
| IN UINTN MaximumPacketLength, | |
| IN OUT VOID *Data, | |
| IN OUT UINTN *DataLength, | |
| IN OUT UINT8 *DataToggle, | |
| IN UINTN TimeOut, | |
| IN EFI_USB2_HC_TRANSACTION_TRANSLATOR *Translator, | |
| OUT UINT32 *TransferResult | |
| ); | |
| #define EFI_USB_MAX_ISO_BUFFER_NUM 7 | |
| #define EFI_USB_MAX_ISO_BUFFER_NUM1 2 | |
| /** | |
| Submits isochronous transfer to an isochronous endpoint of a USB device. | |
| This function is used to submit isochronous transfer to a target endpoint of a USB device. | |
| The target endpoint is specified by DeviceAddressand EndpointAddress. Isochronous transfers are | |
| used when working with isochronous date. It provides periodic, continuous communication between | |
| the host and a device. Isochronous transfers can beused only by full-speed, high-speed, and | |
| super-speed devices. | |
| High-speed isochronous transfers can be performed using multiple data buffers. The number of | |
| buffers that are actually prepared for the transfer is specified by DataBuffersNumber. For | |
| full-speed isochronous transfers this value is ignored. | |
| Data represents a list of pointers to the data buffers. For full-speed isochronous transfers | |
| only the data pointed by Data[0]shall be used. For high-speed isochronous transfers and for | |
| the split transactions depending on DataLengththere several data buffers canbe used. For the | |
| high-speed isochronous transfers the total number of buffers must not exceed EFI_USB_MAX_ISO_BUFFER_NUM. | |
| For split transactions performed on full-speed device by high-speed host controller the total | |
| number of buffers is limited to EFI_USB_MAX_ISO_BUFFER_NUM1. | |
| If the isochronous transfer is successful, then EFI_SUCCESSis returned. The isochronous transfer | |
| is designed to be completed within one USB frame time, if it cannot be completed, EFI_TIMEOUT | |
| is returned. If an error other than timeout occurs during the USB transfer, then EFI_DEVICE_ERROR | |
| is returned and the detailed status code will be returned in TransferResult. | |
| EFI_INVALID_PARAMETERis returned if one of the following conditionsis satisfied: | |
| - Data is NULL. | |
| - DataLength is 0. | |
| - DeviceSpeed is not one of the supported values listed above. | |
| - MaximumPacketLength is invalid. MaximumPacketLength must be 1023 or less for full-speed devices, | |
| and 1024 or less for high-speed and super-speed devices. | |
| - TransferResult is NULL. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param DeviceAddress Represents the address of the target device on the USB. | |
| @param EndPointAddress The combination of an endpoint number and an endpoint direction of the | |
| target USB device. | |
| @param DeviceSpeed Indicates device speed. The supported values are EFI_USB_SPEED_FULL, | |
| EFI_USB_SPEED_HIGH, or EFI_USB_SPEED_SUPER. | |
| @param MaximumPacketLength Indicates the maximum packet size the target endpoint is capable of | |
| sending or receiving. | |
| @param DataBuffersNumber Number of data buffers prepared for the transfer. | |
| @param Data Array of pointers to the buffers of data that will be transmitted to USB | |
| device or received from USB device. | |
| @param DataLength Specifies the length, in bytes, of the data to be sent to or received from | |
| the USB device. | |
| @param Translator A pointer to the transaction translator data. | |
| @param TransferResult A pointer to the detailed result information of the isochronous transfer. | |
| @retval EFI_SUCCESS The isochronous transfer was completed successfully. | |
| @retval EFI_INVALID_PARAMETER Some parameters are invalid. | |
| @retval EFI_OUT_OF_RESOURCES The isochronous transfer could not be submitted due to a lack of resources. | |
| @retval EFI_TIMEOUT The isochronous transfer cannot be completed within the one USB frame time. | |
| @retval EFI_DEVICE_ERROR The isochronous transfer failed due to host controller or device error. | |
| Caller should check TransferResult for detailed error information. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_ISOCHRONOUS_TRANSFER)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 DeviceAddress, | |
| IN UINT8 EndPointAddress, | |
| IN UINT8 DeviceSpeed, | |
| IN UINTN MaximumPacketLength, | |
| IN UINT8 DataBuffersNumber, | |
| IN OUT VOID *Data[EFI_USB_MAX_ISO_BUFFER_NUM], | |
| IN UINTN DataLength, | |
| IN EFI_USB2_HC_TRANSACTION_TRANSLATOR *Translator, | |
| OUT UINT32 *TransferResult | |
| ); | |
| /** | |
| Submits nonblocking isochronous transfer to an isochronous endpoint of a USB device. | |
| This is an asynchronous type of USB isochronous transfer. If the caller submits a USB | |
| isochronous transfer request through this function, this function will return immediately. | |
| When the isochronous transfer completes, the IsochronousCallbackfunction will be triggered, | |
| the caller can know the transfer results. If the transfer is successful, the caller can get | |
| the data received or sent in this callback function. | |
| The target endpoint is specified by DeviceAddressand EndpointAddress. Isochronous transfers | |
| are used when working with isochronous date. It provides periodic, continuous communication | |
| between the host and a device. Isochronous transfers can be used only by full-speed, high-speed, | |
| and super-speed devices. | |
| High-speed isochronous transfers can be performed using multiple data buffers. The number of | |
| buffers that are actually prepared for the transfer is specified by DataBuffersNumber. For | |
| full-speed isochronous transfers this value is ignored. | |
| Data represents a list of pointers to the data buffers. For full-speed isochronous transfers | |
| only the data pointed by Data[0] shall be used. For high-speed isochronous transfers and for | |
| the split transactions depending on DataLength there several data buffers can be used. For | |
| the high-speed isochronous transfers the total number of buffers must not exceed EFI_USB_MAX_ISO_BUFFER_NUM. | |
| For split transactions performed on full-speed device by high-speed host controller the total | |
| number of buffers is limited to EFI_USB_MAX_ISO_BUFFER_NUM1. | |
| EFI_INVALID_PARAMETER is returned if one of the following conditionsis satisfied: | |
| - Data is NULL. | |
| - DataLength is 0. | |
| - DeviceSpeed is not one of the supported values listed above. | |
| - MaximumPacketLength is invalid. MaximumPacketLength must be 1023 or less for full-speed | |
| devices and 1024 or less for high-speed and super-speed devices. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param DeviceAddress Represents the address of the target device on the USB. | |
| @param EndPointAddress The combination of an endpoint number and an endpoint direction of the | |
| target USB device. | |
| @param DeviceSpeed Indicates device speed. The supported values are EFI_USB_SPEED_FULL, | |
| EFI_USB_SPEED_HIGH, or EFI_USB_SPEED_SUPER. | |
| @param MaximumPacketLength Indicates the maximum packet size the target endpoint is capable of | |
| sending or receiving. | |
| @param DataBuffersNumber Number of data buffers prepared for the transfer. | |
| @param Data Array of pointers to the buffers of data that will be transmitted to USB | |
| device or received from USB device. | |
| @param DataLength Specifies the length, in bytes, of the data to be sent to or received from | |
| the USB device. | |
| @param Translator A pointer to the transaction translator data. | |
| @param IsochronousCallback The Callback function. This function is called if the requested | |
| isochronous transfer is completed. | |
| @param Context Data passed to the IsochronousCallback function. This is an | |
| optional parameter and may be NULL. | |
| @retval EFI_SUCCESS The asynchronous isochronous transfer request has been successfully | |
| submitted or canceled. | |
| @retval EFI_INVALID_PARAMETER Some parameters are invalid. | |
| @retval EFI_OUT_OF_RESOURCES The asynchronous isochronous transfer could not be submitted due to | |
| a lack of resources. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_ASYNC_ISOCHRONOUS_TRANSFER)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 DeviceAddress, | |
| IN UINT8 EndPointAddress, | |
| IN UINT8 DeviceSpeed, | |
| IN UINTN MaximumPacketLength, | |
| IN UINT8 DataBuffersNumber, | |
| IN OUT VOID *Data[EFI_USB_MAX_ISO_BUFFER_NUM], | |
| IN UINTN DataLength, | |
| IN EFI_USB2_HC_TRANSACTION_TRANSLATOR *Translator, | |
| IN EFI_ASYNC_USB_TRANSFER_CALLBACK IsochronousCallBack, | |
| IN VOID *Context OPTIONAL | |
| ); | |
| /** | |
| Retrieves the current status of a USB root hub port. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param PortNumber Specifies the root hub port from which the status is to be retrieved. | |
| This value is zero based. | |
| @param PortStatus A pointer to the current port status bits and port status change bits. | |
| @retval EFI_SUCCESS The status of the USB root hub port specified by PortNumber | |
| was returned in PortStatus. | |
| @retval EFI_INVALID_PARAMETER PortNumber is invalid. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_GET_ROOTHUB_PORT_STATUS)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 PortNumber, | |
| OUT EFI_USB_PORT_STATUS *PortStatus | |
| ); | |
| /** | |
| Sets a feature for the specified root hub port. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param PortNumber Specifies the root hub port whose feature is requested to be set. This | |
| value is zero based. | |
| @param PortFeature Indicates the feature selector associated with the feature set request. | |
| @retval EFI_SUCCESS The feature specified by PortFeature was set for the USB | |
| root hub port specified by PortNumber. | |
| @retval EFI_INVALID_PARAMETER PortNumber is invalid or PortFeature is invalid for this function. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_SET_ROOTHUB_PORT_FEATURE)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 PortNumber, | |
| IN EFI_USB_PORT_FEATURE PortFeature | |
| ); | |
| /** | |
| Clears a feature for the specified root hub port. | |
| @param This A pointer to the EFI_USB2_HC_PROTOCOL instance. | |
| @param PortNumber Specifies the root hub port whose feature is requested to be cleared. This | |
| value is zero based. | |
| @param PortFeature Indicates the feature selector associated with the feature clear request. | |
| @retval EFI_SUCCESS The feature specified by PortFeature was cleared for the USB | |
| root hub port specified by PortNumber. | |
| @retval EFI_INVALID_PARAMETER PortNumber is invalid or PortFeature is invalid for this function. | |
| **/ | |
| typedef | |
| EFI_STATUS | |
| (EFIAPI *EFI_USB2_HC_PROTOCOL_CLEAR_ROOTHUB_PORT_FEATURE)( | |
| IN EFI_USB2_HC_PROTOCOL *This, | |
| IN UINT8 PortNumber, | |
| IN EFI_USB_PORT_FEATURE PortFeature | |
| ); | |
| /// | |
| /// The EFI_USB2_HC_PROTOCOL provides USB host controller management, basic | |
| /// data transactions over a USB bus, and USB root hub access. A device driver | |
| /// that wishes to manage a USB bus in a system retrieves the EFI_USB2_HC_PROTOCOL | |
| /// instance that is associated with the USB bus to be managed. A device handle | |
| /// for a USB host controller will minimally contain an EFI_DEVICE_PATH_PROTOCOL | |
| /// instance, and an EFI_USB2_HC_PROTOCOL instance. | |
| /// | |
| struct _EFI_USB2_HC_PROTOCOL { | |
| EFI_USB2_HC_PROTOCOL_GET_CAPABILITY GetCapability; | |
| EFI_USB2_HC_PROTOCOL_RESET Reset; | |
| EFI_USB2_HC_PROTOCOL_GET_STATE GetState; | |
| EFI_USB2_HC_PROTOCOL_SET_STATE SetState; | |
| EFI_USB2_HC_PROTOCOL_CONTROL_TRANSFER ControlTransfer; | |
| EFI_USB2_HC_PROTOCOL_BULK_TRANSFER BulkTransfer; | |
| EFI_USB2_HC_PROTOCOL_ASYNC_INTERRUPT_TRANSFER AsyncInterruptTransfer; | |
| EFI_USB2_HC_PROTOCOL_SYNC_INTERRUPT_TRANSFER SyncInterruptTransfer; | |
| EFI_USB2_HC_PROTOCOL_ISOCHRONOUS_TRANSFER IsochronousTransfer; | |
| EFI_USB2_HC_PROTOCOL_ASYNC_ISOCHRONOUS_TRANSFER AsyncIsochronousTransfer; | |
| EFI_USB2_HC_PROTOCOL_GET_ROOTHUB_PORT_STATUS GetRootHubPortStatus; | |
| EFI_USB2_HC_PROTOCOL_SET_ROOTHUB_PORT_FEATURE SetRootHubPortFeature; | |
| EFI_USB2_HC_PROTOCOL_CLEAR_ROOTHUB_PORT_FEATURE ClearRootHubPortFeature; | |
| /// | |
| /// The major revision number of the USB host controller. The revision information | |
| /// indicates the release of the Universal Serial Bus Specification with which the | |
| /// host controller is compliant. | |
| /// | |
| UINT16 MajorRevision; | |
| /// | |
| /// The minor revision number of the USB host controller. The revision information | |
| /// indicates the release of the Universal Serial Bus Specification with which the | |
| /// host controller is compliant. | |
| /// | |
| UINT16 MinorRevision; | |
| }; | |
| extern EFI_GUID gEfiUsb2HcProtocolGuid; | |
| #endif |