menu "PowerPC and LayerScape SPL Boot options"
	depends on (PPC && SUPPORT_SPL && !SPL_FRAMEWORK) || \
		   ((ARCH_LS1021A || ARCH_LS1043A || ARCH_LS1046A) && SUPPORT_SPL)

config SPL_NAND_BOOT
	bool "Load SPL from NAND flash"
	depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)

config SPL_MMC_BOOT
	bool "Load SPL from SD Card / eMMC"
	depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)

config SPL_SPI_BOOT
	bool "Load SPL from SPI flash"
	depends on PPC && (SUPPORT_SPL && !SPL_FRAMEWORK)

config SPL_FSL_PBL
	bool "Create SPL in Freescale PBI format"
	depends on (PPC || ARCH_LS1021A || ARCH_LS1043A || ARCH_LS1046A) && \
		    SUPPORT_SPL
	help
	  Create boot binary having SPL binary in PBI format concatenated with
	  u-boot binary.

config SPL_SYS_CCSR_DO_NOT_RELOCATE
	bool "Ensures that CCSR is not relocated"
	depends on PPC
	help
	  If this is defined, then CFG_SYS_CCSRBAR_PHYS will be forced to a
	  value that ensures that CCSR is not relocated.

config TPL_SYS_CCSR_DO_NOT_RELOCATE
	def_bool y
	depends on SPL_SYS_CCSR_DO_NOT_RELOCATE

menu "PowerPC SPL / TPL specific options"
	depends on PPC && (SPL && !SPL_FRAMEWORK)

config SPL_INIT_MINIMAL
	bool "Arch init code will be built for a very small image"

config SPL_FLUSH_IMAGE
	bool "Clean dcache and invalidate icache after loading the image"

config SPL_SKIP_RELOCATE
	bool "Skip relocating SPL"

config SPL_GD_ADDR
	hex "Address to use for global data (gd) in SPL"
	depends on !SPL_INIT_MINIMAL

config SPL_RELOC_TEXT_BASE
	hex "Address to relocate SPL to"
	default SPL_TEXT_BASE
	help
	  If unspecified, this is equal to CONFIG_SPL_TEXT_BASE (i.e. no
	  relocation is done).

config SPL_RELOC_STACK
	hex "Address of the start of the stack SPL will use after relocation."
	help
	  If unspecified, this is equal to CFG_SYS_SPL_MALLOC_START.  Starting
	  address of the malloc pool used in SPL.  When this option is set the full
	  malloc is used in SPL and it is set up by spl_init() and before that, the
	  simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.

config SPL_RELOC_MALLOC
	bool "SPL has malloc pool after relocation"

config SPL_RELOC_MALLOC_ADDR
	hex "Address of malloc pool in SPL"
	depends on SPL_RELOC_MALLOC

config SPL_RELOC_MALLOC_SIZE
	hex "Size of malloc pool in SPL"
	depends on SPL_RELOC_MALLOC

config TPL_GD_ADDR
	hex "Address to use for global data (gd) in TPL"
	depends on TPL

config TPL_RELOC_TEXT_BASE
	hex "Address to relocate TPL to"
	depends on TPL
	default TPL_TEXT_BASE
	help
	  If unspecified, this is equal to CONFIG_TPL_TEXT_BASE (i.e. no
	  relocation is done).

config TPL_RELOC_STACK
	hex "Address of the start of the stack TPL will use after relocation."
	depends on TPL
	help
	  If unspecified, this is equal to CONFIG_SYS_TPL_MALLOC_START.  Starting
	  address of the malloc pool used in TPL.  When this option is set the full
	  malloc is used in TPL and it is set up by spl_init() and before that, the
	  simple malloc() can be used if CONFIG_SYS_MALLOC_F is defined.

config TPL_RELOC_MALLOC
	bool "TPL has malloc pool after relocation"
	depends on TPL

config TPL_RELOC_MALLOC_ADDR
	hex "Address of malloc pool in TPL"
	depends on TPL_RELOC_MALLOC

config TPL_RELOC_MALLOC_SIZE
	hex "Size of malloc pool in TPL"
	depends on TPL_RELOC_MALLOC

config TPL_PAD_TO
	hex "Offset to which the TPL should be padded before appending the TPL payload"
	depends on TPL && !TPL_FRAMEWORK
	default TPL_MAX_SIZE
	help
	  Image offset to which the TPL should be padded before appending the
	  TPL payload. By default, this is defined as CONFIG_TPL_MAX_SIZE, or 0 if
	  CONFIG_TPL_MAX_SIZE is undefined.  CONFIG_TPL_PAD_TO must be either
	  0, meaning to append the TPL payload without any padding, or >=
	  CONFIG_TPL_MAX_SIZE.
endmenu

endmenu