blob: 72511e401e3cea6e0c48cf6f079907cc2ba9ce80 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2010-2013, NVIDIA CORPORATION. All rights reserved.
*/
#include <common.h>
#include <dm.h>
#include <log.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/gp_padctrl.h>
#include "pinmux-config-dalmore.h"
#include <i2c.h>
#define BAT_I2C_ADDRESS 0x48 /* TPS65090 charger */
#define PMU_I2C_ADDRESS 0x58 /* TPS65913 PMU */
/*
* Routine: pinmux_init
* Description: Do individual peripheral pinmux configs
*/
void pinmux_init(void)
{
pinmux_config_pingrp_table(tegra114_pinmux_set_nontristate,
ARRAY_SIZE(tegra114_pinmux_set_nontristate));
pinmux_config_pingrp_table(tegra114_pinmux_common,
ARRAY_SIZE(tegra114_pinmux_common));
pinmux_config_pingrp_table(unused_pins_lowpower,
ARRAY_SIZE(unused_pins_lowpower));
/* Initialize any non-default pad configs (APB_MISC_GP regs) */
pinmux_config_drvgrp_table(dalmore_padctrl,
ARRAY_SIZE(dalmore_padctrl));
}
#if defined(CONFIG_MMC_SDHCI_TEGRA)
/*
* Do I2C/PMU writes to bring up SD card bus power
*
*/
void board_sdmmc_voltage_init(void)
{
struct udevice *dev;
uchar reg, data_buffer[1];
int ret;
ret = i2c_get_chip_for_busnum(0, PMU_I2C_ADDRESS, 1, &dev);
if (ret) {
debug("%s: Cannot find PMIC I2C chip\n", __func__);
return;
}
/* TPS65913: LDO9_VOLTAGE = 3.3V */
data_buffer[0] = 0x31;
reg = 0x61;
ret = dm_i2c_write(dev, reg, data_buffer, 1);
if (ret)
printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
__func__, reg, data_buffer[0], ret);
/* TPS65913: LDO9_CTRL = Active */
data_buffer[0] = 0x01;
reg = 0x60;
ret = dm_i2c_write(dev, reg, data_buffer, 1);
if (ret)
printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
__func__, reg, data_buffer[0], ret);
/* TPS65090: FET6_CTRL = enable output auto discharge, enable FET6 */
data_buffer[0] = 0x03;
reg = 0x14;
ret = i2c_get_chip_for_busnum(0, BAT_I2C_ADDRESS, 1, &dev);
if (ret) {
debug("%s: Cannot find charger I2C chip\n", __func__);
return;
}
ret = dm_i2c_write(dev, reg, data_buffer, 1);
if (ret)
printf("%s: BAT i2c_write %02X<-%02X returned %d\n",
__func__, reg, data_buffer[0], ret);
}
/*
* Routine: pin_mux_mmc
* Description: setup the MMC muxes, power rails, etc.
*/
void pin_mux_mmc(void)
{
/*
* NOTE: We don't do mmc-specific pin muxes here.
* They were done globally in pinmux_init().
*/
/* Bring up the SDIO3 power rail */
board_sdmmc_voltage_init();
}
#endif /* MMC */