/* SPDX-License-Identifier: GPL-2.0 */
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/gpio/x86-gpio.h>

/include/ "skeleton.dtsi"
/include/ "keyboard.dtsi"
/include/ "reset.dtsi"
/include/ "rtc.dtsi"

#include "tsc_timer.dtsi"

#if defined(CONFIG_CHROMEOS_VBOOT) && defined(CONFIG_ROM_SIZE)
#include "chromeos-x86.dtsi"
#include "flashmap-x86-ro.dtsi"
#include "flashmap-16mb-rw.dtsi"
#endif

#include <dt-bindings/clock/intel-clock.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/x86-irq.h>
#include <asm/e820.h>
#include <asm/intel_pinctrl_defs.h>
#include <asm/arch-apollolake/cpu.h>
#include <asm/arch-apollolake/gpe.h>
#include <asm/arch-apollolake/gpio.h>
#include <asm/arch-apollolake/iomap.h>
#include <asm/arch-apollolake/pm.h>
#include <dt-bindings/clock/intel-clock.h>
#include <asm/arch-apollolake/fsp/fsp_m_upd.h>
#include <asm/arch-apollolake/fsp/fsp_s_upd.h>
#include <dt-bindings/sound/nhlt.h>

/ {
	model = "Google Coral";
	compatible = "google,coral", "intel,apollolake";

	aliases {
		cros-ec0 = &cros_ec;
		fsp = &fsp_s;
		spi0 = &spi;
		i2c0 = &i2c_0;
		i2c1 = &i2c_1;
		i2c2 = &i2c_2;
		i2c3 = &i2c_3;
		i2c4 = &i2c_4;
		i2c5 = &i2c_5;
		i2c6 = &i2c_6;
		i2c7 = &i2c_7;
		mmc0 = &emmc;
		mmc1 = &sdmmc;
	};

	board: board {
		compatible = "google,coral";
		recovery-gpios = <&gpio_nw (-1) GPIO_ACTIVE_LOW>;
		write-protect-gpios = <&gpio_nw GPIO_75 GPIO_ACTIVE_HIGH>;
		phase-enforce-gpios = <&gpio_n GPIO_10 GPIO_ACTIVE_HIGH>;
		memconfig-gpios = <&gpio_nw GPIO_101 GPIO_ACTIVE_HIGH
			&gpio_nw GPIO_102 GPIO_ACTIVE_HIGH
			&gpio_n GPIO_38 GPIO_ACTIVE_HIGH
			&gpio_n GPIO_45 GPIO_ACTIVE_HIGH>;

		/*
		 * This is used for reef only:
		 *
		 * skuconfig-gpios = <&gpio_nw GPIO_16 GPIO_ACTIVE_HIGH
		 *	&gpio_nw GPIO_17 GPIO_ACTIVE_HIGH>;
		 */
		smbios {
			/* Type 1 table */
			system {
				manufacturer = "Google";
				product = "Coral";
				version = "rev2";
				serial = "123456789";
				sku = "sku3";
				family = "Google_Coral";
			};

			/* Type 2 table */
			baseboard {
				manufacturer = "Google";
				product = "Coral";
				asset-tag = "ABC123";
			};

			/* Type 3 table */
			chassis {
				manufacturer = "Google";
			};
		};
	};

	config {
	       silent_console = <0>;
	};

	chosen {
		stdout-path = &serial;
		e820-entries = /bits/ 64 <
			IOMAP_P2SB_BAR IOMAP_P2SB_SIZE E820_RESERVED
			MCH_BASE_ADDRESS     MCH_SIZE  E820_RESERVED>;
		u-boot,acpi-ssdt-order = <&cpu_0 &cpu_1 &cpu_2 &cpu_3
			&i2c_0 &i2c_1 &i2c_2 &i2c_3 &i2c_4 &i2c_5
			&sdmmc &maxim_codec &wifi &da_codec &tpm
			&elan_touchscreen &raydium_touchscreen
			&elan_touchpad &synaptics_touchpad &wacom_digitizer>;
		u-boot,acpi-dsdt-order = <&board &lpc>;
	};

	clk: clock {
		compatible = "intel,apl-clk";
		#clock-cells = <1>;
		bootph-some-ram;
	};

	cpus {
		bootph-some-ram;
		#address-cells = <1>;
		#size-cells = <0>;

		cpu_0: cpu@0 {
			bootph-some-ram;
			bootph-pre-ram;
			device_type = "cpu";
			compatible = "intel,apl-cpu";
			reg = <0>;
			intel,apic-id = <0>;
		};

		cpu_1: cpu@1 {
			device_type = "cpu";
			compatible = "intel,apl-cpu";
			reg = <1>;
			intel,apic-id = <2>;
		};

		cpu_2: cpu@2 {
			device_type = "cpu";
			compatible = "intel,apl-cpu";
			reg = <2>;
			intel,apic-id = <4>;
		};

		cpu_3: cpu@3 {
			device_type = "cpu";
			compatible = "intel,apl-cpu";
			reg = <3>;
			intel,apic-id = <6>;
		};

	};

	acpi_gpe: general-purpose-events {
		bootph-some-ram;
		reg = <IOMAP_ACPI_BASE IOMAP_ACPI_SIZE>;
		compatible = "intel,acpi-gpe";
		interrupt-controller;
		#interrupt-cells = <2>;
	};

	coreboot-video {
		/* This will only activate when booted from coreboot */
		compatible = "coreboot-fb";
	};

	keyboard {
		intel,duplicate-por;
	};

	pci {
		compatible = "pci-x86";
		#address-cells = <3>;
		#size-cells = <2>;
		bootph-all;
		ranges = <0x02000000 0x0 0xc0000000 0xc0000000 0 0x10000000
			0x42000000 0x0 0xb0000000 0xb0000000 0 0x10000000
			0x01000000 0x0 0x1000 0x1000 0 0xefff>;
		u-boot,skip-auto-config-until-reloc;

		host_bridge: host-bridge@0,0 {
			bootph-all;
			reg = <0x00000000 0 0 0 0>;
			compatible = "intel,apl-hostbridge";
			pciex-region-size = <0x10000000>;
			fspm,training-delay = <21>;
			/*
			 * Parameters used by the FSP-S binary blob. This is
			 * really unfortunate since these parameters mostly
			 * relate to drivers but we need them in one place. We
			 * could put them in the driver nodes easily, but then
			 * would have to scan each node to find them. So just
			 * dump them here for now.
			 */
			fsp_s: fsp-s {
			};
			fsp_m: fsp-m {
				bootph-pre-ram;
			};

			nhlt {
				intel,dmic-channels = <4>;
			};
		};

		punit@0,1 {
			bootph-some-ram;
			bootph-pre-ram;
			reg = <0x00000800 0 0 0 0>;
			compatible = "intel,apl-punit";
		};

		gma@2,0 {
			bootph-some-ram;
			reg = <0x00001000 0 0 0 0>;
			compatible = "fsp-fb";
		};

		p2sb: p2sb@d,0 {
			bootph-all;
			reg = <0x02006810 0 0 0 0>;
			compatible = "intel,p2sb";
			early-regs = <IOMAP_P2SB_BAR 0x100000>;
			pci,no-autoconfig;

			n {
				compatible = "intel,apl-pinctrl";
				bootph-all;
				intel,p2sb-port-id = <PID_GPIO_N>;
				acpi,path = "\\_SB.GPO0";
				gpio_n: gpio-n {
					compatible = "intel,gpio";
					bootph-all;
					gpio-controller;
					#gpio-cells = <2>;
					linux-name = "INT3452:00";
				};
			};

			nw {
				bootph-all;
				compatible = "intel,apl-pinctrl";
				intel,p2sb-port-id = <PID_GPIO_NW>;
				#gpio-cells = <2>;
				acpi,path = "\\_SB.GPO1";
				gpio_nw: gpio-nw {
					compatible = "intel,gpio";
					bootph-all;
					gpio-controller;
					#gpio-cells = <2>;
					linux-name = "INT3452:01";
				};
			};

			w {
				bootph-all;
				compatible = "intel,apl-pinctrl";
				intel,p2sb-port-id = <PID_GPIO_W>;
				#gpio-cells = <2>;
				acpi,path = "\\_SB.GPO2";
				gpio_w: gpio-w {
					compatible = "intel,gpio";
					bootph-all;
					gpio-controller;
					#gpio-cells = <2>;
					linux-name = "INT3452:02";
				};
			};

			sw {
				bootph-all;
				compatible = "intel,apl-pinctrl";
				intel,p2sb-port-id = <PID_GPIO_SW>;
				#gpio-cells = <2>;
				acpi,path = "\\_SB.GPO3";
				gpio_sw: gpio-sw {
					compatible = "intel,gpio";
					bootph-all;
					gpio-controller;
					#gpio-cells = <2>;
					linux-name = "INT3452:03";
				};
			};

			itss {
				bootph-all;
				compatible = "intel,itss";
				intel,p2sb-port-id = <PID_ITSS>;
				intel,pmc-routes = <
					PMC_GPE_SW_31_0 GPIO_GPE_SW_31_0
					PMC_GPE_SW_63_32 GPIO_GPE_SW_63_32
					PMC_GPE_NW_31_0 GPIO_GPE_NW_31_0
					PMC_GPE_NW_63_32 GPIO_GPE_NW_63_32
					PMC_GPE_NW_95_64 GPIO_GPE_NW_95_64
					PMC_GPE_N_31_0 GPIO_GPE_N_31_0
					PMC_GPE_N_63_32 GPIO_GPE_N_63_32
					PMC_GPE_W_31_0 GPIO_GPE_W_31_0>;
			};
		};

		pmc@d,1 {
			bootph-all;
			reg = <0x6900 0 0 0 0>;

			/*
			 * Values for BAR0, BAR2 and ACPI_BASE for when PCI
			 * auto-configure is not available
			 */
			early-regs = <0xfe042000 0x2000
				0xfe044000 0x2000
				IOMAP_ACPI_BASE IOMAP_ACPI_SIZE>;
			compatible = "intel,apl-pmc";
			gpe0-dwx-mask = <0xf>;
			gpe0-dwx-shift-base = <4>;

			/*
			 * GPE configuration
			 * Note that GPE events called out in ASL code rely on
			 * this route, i.e., if this route changes then the
			 * affected GPE * offset bits also need to be changed.
			 * This sets the PMC register GPE_CFG fields.
			 */
			gpe0-dw = <PMC_GPE_N_31_0
				PMC_GPE_N_63_32
				PMC_GPE_SW_31_0>;
			gpe0-sts = <0x20>;
			gpe0-en = <0x30>;
		};

		audio@e,0 {
			reg = <0x7000 0 0 0 0>;
			compatible = "simple-bus";
			acpi,name = "HDAS";
			i2s {
				compatible = "fred";
			};
			maxim_codec: maxim-codec {
				compatible = "maxim,max98357a";
				acpi,ddn = "Maxim Integrated 98357A Amplifier";
				sdmode-gpios = <&gpio_n GPIO_76 GPIO_ACTIVE_HIGH>;
				sdmode-delay = <5>;
				acpi,name = "MAXM";
				acpi,hid = "MX98357A";
				acpi,audio-link = <AUDIO_LINK_SSP5>;
			};
		};

		spi: fast-spi@d,2 {
			bootph-some-ram;
			bootph-pre-ram;
			reg = <0x02006a10 0 0 0 0>;
			#address-cells = <1>;
			#size-cells = <0>;
			compatible = "intel,fast-spi";
			early-regs = <IOMAP_SPI_BASE 0x1000>;
			intel,hardware-seq = <1>;

			fwstore_spi: spi-flash@0 {
				#size-cells = <1>;
				#address-cells = <1>;
				bootph-some-ram;
				bootph-pre-ram;
				reg = <0>;
				m25p,fast-read;
				compatible = "winbond,w25q128fw",
					 "jedec,spi-nor";
				rw-mrc-cache {
					label = "rw-mrc-cache";
					reg = <0x008e0000 0x00010000>;
					bootph-all;
				};
				rw-var-mrc-cache {
					label = "rw-mrc-cache";
					reg = <0x008f0000 0x0001000>;
					bootph-all;
				};
			};
		};

		/* WiFi */
		pcie-a0@14,0 {
			reg = <0x0000a000 0 0 0 0>;
			acpi,name = "RP01";
			wifi: wifi {
				compatible = "intel,generic-wifi";
				acpi,ddn = "Intel WiFi";
				acpi,name = "WF00";
				acpi,wake = <GPE0_DW3_00>;
				interrupts-extended = <&acpi_gpe 0x3c 0>;
			};
		};

		i2c_0: i2c2@16,0 {
			compatible = "intel,apl-i2c";
			reg = <0x0200b010 0 0 0 0>;
			clocks = <&clk CLK_I2C>;
			i2c-scl-rising-time-ns = <104>;
			i2c-scl-falling-time-ns = <52>;
			clock-frequency = <400000>;
			i2c,speeds = <100000 400000 1000000>;
			#address-cells = <1>;
			#size-cells = <0>;
			da_codec: da-codec {
				reg = <0x1a>;
				compatible = "dlg,da7219";
				interrupts-extended = <&acpi_gpe GPIO_116_IRQ
					(IRQ_TYPE_LEVEL_LOW | X86_IRQ_TYPE_SHARED)>;
				acpi,name = "DLG7";
				acpi,ddn = "Dialog Semiconductor DA7219 Audio Codec";
				acpi,audio-link = <AUDIO_LINK_SSP1>;
				dlg,micbias-lvl = <2600>;
				dlg,mic-amp-in-sel = "diff";
				da7219_aad {
					dlg,btn-cfg = <50>;
					dlg,mic-det-thr = <500>;
					dlg,jack-ins-deb = <20>;
					dlg,jack-det-rate = "32ms_64ms";
					dlg,jack-rem-deb = <1>;
					dlg,a-d-btn-thr = <0xa>;
					dlg,d-b-btn-thr = <0x16>;
					dlg,b-c-btn-thr = <0x21>;
					dlg,c-mic-btn-thr = <0x3e>;
					dlg,btn-avg = <4>;
					dlg,adc-1bit-rpt = <1>;
				};
			};
		};

		i2c_1: i2c2@16,1 {
			compatible = "intel,apl-i2c";
			reg = <0x0200b110 0 0 0 0>;
			clocks = <&clk CLK_I2C>;
			clock-frequency = <400000>;
			i2c,speeds = <100000 400000 1000000 3400000>;
			i2c-scl-rising-time-ns = <52>;
			i2c-scl-falling-time-ns = <52>;
		};

		i2c_2: i2c2@16,2 {
			compatible = "intel,apl-i2c", "snps,designware-i2c-pci";
			reg = <0x0200b210 0 0 0 0>;
			early-regs = <IOMAP_I2C2_BASE 0x1000>;
			bootph-some-ram;
			#address-cells = <1>;
			#size-cells = <0>;
			clock-frequency = <400000>;
			i2c,speeds = <100000 400000 1000000>;
			clocks = <&clk CLK_I2C>;
			i2c-scl-rising-time-ns = <57>;
			i2c-scl-falling-time-ns = <28>;
			tpm: tpm@50 {
				reg = <0x50>;
				compatible = "google,cr50";
				bootph-some-ram;
				u-boot,i2c-offset-len = <0>;
				ready-gpios = <&gpio_n 28 GPIO_ACTIVE_LOW>;
				interrupts-extended = <&acpi_gpe GPIO_28_IRQ
					 IRQ_TYPE_EDGE_FALLING>;
				acpi,hid = "GOOG0005";
				acpi,ddn = "I2C TPM";
				acpi,name = "TPMI";
			};
		};

		i2c_3: i2c2@16,3 {
			compatible = "intel,apl-i2c";
			reg = <0x0200b310 0 0 0 0>;
			#address-cells = <1>;
			#size-cells = <0>;
			clocks = <&clk CLK_I2C>;
			i2c-scl-rising-time-ns = <76>;
			i2c-scl-falling-time-ns = <164>;
			clock-frequency = <400000>;
			i2c,speeds = <100000 400000>;
			elan_touchscreen: elan-touchscreen@10 {
				compatible = "i2c-chip";
				reg = <0x10>;
				acpi,hid = "ELAN0001";
				acpi,ddn = "ELAN Touchscreen";
				interrupts-extended = <&acpi_gpe GPIO_21_IRQ
					IRQ_TYPE_EDGE_FALLING>;
				linux,probed;
				reset-gpios = <&gpio_n GPIO_36 GPIO_ACTIVE_HIGH>;
				reset-delay-ms = <20>;
				enable-gpios = <&gpio_n GPIO_152 GPIO_ACTIVE_HIGH>;
				enable-delay-ms = <1>;
				acpi,has-power-resource;
			};

			raydium_touchscreen: raydium-touchscreen@39 {
				compatible = "i2c-chip";
				reg = <0x39>;
				acpi,hid = "RAYD0001";
				acpi,ddn = "Raydium Touchscreen";
				interrupts-extended = <&acpi_gpe GPIO_21_IRQ
					IRQ_TYPE_EDGE_FALLING>;
				linux,probed;
				reset-gpios = <&gpio_n GPIO_36 GPIO_ACTIVE_HIGH>;
				reset-delay-ms = <1>;
				enable-gpios = <&gpio_n GPIO_152 GPIO_ACTIVE_HIGH>;
				enable-delay-ms = <50>;
				acpi,has-power-resource;
			};
		};

		i2c_4: i2c2@17,0 {
			compatible = "intel,apl-i2c";
			reg = <0x0200b810 0 0 0 0>;
			#address-cells = <1>;
			#size-cells = <0>;
			clocks = <&clk CLK_I2C>;
			i2c-sda-hold-time-ns = <350>;
			i2c-scl-rising-time-ns = <114>;
			i2c-scl-falling-time-ns = <164>;
			clock-frequency = <400000>;
			i2c,speeds = <100000 400000>;
			elan_touchpad: elan-touchpad@15 {
				compatible = "i2c-chip";
				reg = <0x15>;
				u-boot,i2c-offset-len = <0>;
				acpi,hid = "ELAN0000";
				acpi,ddn = "ELAN Touchpad";
				interrupts-extended = <&acpi_gpe GPIO_18_IRQ
					 IRQ_TYPE_EDGE_FALLING>;
				acpi,wake = <GPE0_DW1_15>;
				linux,probed;
			};
			synaptics_touchpad: synaptics-touchpad@2c {
				compatible = "hid-over-i2c";
				reg = <0x2c>;
				acpi,hid = "PNP0C50";
				acpi,ddn = "Synaptics Touchpad";
				interrupts-extended = <&acpi_gpe GPIO_18_IRQ
					 IRQ_TYPE_EDGE_FALLING>;
				acpi,wake = <GPE0_DW1_15>;
				linux,probed;
				hid-descr-addr = <0x20>;
			};
		};

		i2c_5: i2c2@17,1 {
			compatible = "intel,apl-i2c";
			reg = <0x0200b910 0 0 0 0>;
			#address-cells = <1>;
			#size-cells = <0>;
			clocks = <&clk CLK_I2C>;
			i2c-scl-rising-time-ns = <76>;
			i2c-scl-falling-time-ns = <164>;
			clock-frequency = <400000>;
			i2c,speeds = <100000 400000 1000000>;
			wacom_digitizer: wacom-digitizer@9 {
				compatible = "hid-over-i2c";
				reg = <0x9>;
				acpi,hid = "WCOM50C1";
				acpi,ddn = "WCOM Digitizer";
				interrupts-extended = <&acpi_gpe GPIO_13_IRQ
					(IRQ_TYPE_LEVEL_LOW | X86_IRQ_TYPE_SHARED)>;
				hid-descr-addr = <0x1>;
			};
		};

		i2c_6: i2c2@17,2 {
			compatible = "intel,apl-i2c";
			reg = <0x0200ba10 0 0 0 0>;
			clocks = <&clk CLK_I2C>;
			status = "disabled";
		};

		i2c_7: i2c2@17,3 {
			compatible = "intel,apl-i2c";
			reg = <0x0200bb10 0 0 0 0>;
			clocks = <&clk CLK_I2C>;
			status = "disabled";
		};

		serial: serial@18,2 {
			reg = <0x0200c210 0 0 0 0>;
			bootph-all;
			compatible = "intel,apl-ns16550";
			early-regs = <0xde000000 0x20>;
			reg-shift = <2>;
			clock-frequency = <1843200>;
			current-speed = <115200>;
			acpi,name = "URT3";
			pci,no-autoconfig;
		};

		sdmmc: sdmmc@1b,0 {
			reg = <0x0000d800 0 0 0 0>;
			compatible = "intel,apl-sd";
			cd-gpios = <&gpio_sw GPIO_177 GPIO_ACTIVE_LOW>;
			acpi,name = "SDCD";
		};

		emmc: emmc@1c,0 {
			reg = <0x0000e000 0 0 0 0>;
			compatible = "intel,apl-emmc";
			non-removable;
		};

		pch: pch@1f,0 {
			reg = <0x0000f800 0 0 0 0>;
			compatible = "intel,apl-pch";
			bootph-all;
			#address-cells = <1>;
			#size-cells = <1>;

			lpc: lpc {
				compatible = "intel,apl-lpc";
				#address-cells = <1>;
				#size-cells = <0>;
				bootph-all;
				cros_ec: cros-ec {
					bootph-some-ram;
					bootph-verify;
					compatible = "google,cros-ec-lpc";
					reg = <0x204 1 0x200 1 0x880 0x80>;

					/*
					 * Describes the flash memory within
					 * the EC
					 */
					#address-cells = <1>;
					#size-cells = <1>;
					flash@8000000 {
						reg = <0x08000000 0x20000>;
						erase-value = <0xff>;
					};
				};
			};
		};
	};

};

&host_bridge {
	/*
	 * PL1 override 12000 mW: the energy calculation is wrong with the
	 * current VR solution. Experiments show that SoC TDP max (6W) can be
	 * reached when RAPL PL1 is set to 12W. Set RAPL PL2 to 15W.
	 */
	tdp-pl-override-mw = <12000 15000>;

	early-pads = <
		/* These two are for the debug UART */
		GPIO_46 /* UART2 RX */
			(PAD_CFG0_MODE_NF1 | PAD_CFG0_LOGICAL_RESET_DEEP)
			(PAD_CFG1_PULL_NATIVE | PAD_CFG1_IOSSTATE_TX_LAST_RXE)

		GPIO_47 /* UART2 TX */
			(PAD_CFG0_MODE_NF1 | PAD_CFG0_LOGICAL_RESET_DEEP)
			(PAD_CFG1_PULL_NATIVE | PAD_CFG1_IOSSTATE_TX_LAST_RXE)

		GPIO_75 /* I2S1_BCLK -- PCH_WP */
			(PAD_CFG0_MODE_GPIO | PAD_CFG0_LOGICAL_RESET_DEEP)
			(PAD_CFG1_PULL_UP_20K | PAD_CFG1_IOSSTATE_TXD_RXE)

		/* I2C2 - TPM  */
		GPIO_128 /* LPSS_I2C2_SDA */
			(PAD_CFG0_MODE_NF1 | PAD_CFG0_LOGICAL_RESET_DEEP)
			(PAD_CFG1_PULL_UP_2K | PAD_CFG1_IOSSTATE_TX_LAST_RXE)
		GPIO_129 /* LPSS_I2C2_SCL */
			(PAD_CFG0_MODE_NF1 | PAD_CFG0_LOGICAL_RESET_DEEP)
			(PAD_CFG1_PULL_UP_2K | PAD_CFG1_IOSSTATE_TX_LAST_RXE)
		GPIO_28 /* TPM IRQ */
			(PAD_CFG0_MODE_GPIO | PAD_CFG0_LOGICAL_RESET_DEEP |
				PAD_CFG0_TX_DISABLE | PAD_CFG0_ROUTE_IOAPIC |
				PAD_CFG0_TRIG_LEVEL | PAD_CFG0_RX_POL_INVERT)
			(PAD_CFG1_PULL_NONE | PAD_CFG1_IOSSTATE_TXD_RXE)
		PAD_CFG_GPI(GPIO_25, UP_20K, DEEP)	 /* unused */

		/*
		 * WLAN_PE_RST - default to deasserted just in case FSP
		 * misbehaves
		 */
		GPIO_122  /* SIO_SPI_2_RXD */
			(PAD_CFG0_MODE_GPIO | PAD_CFG0_LOGICAL_RESET_DEEP |
				PAD_CFG0_RX_DISABLE | 0)
			(PAD_CFG1_PULL_NONE | PAD_CFG1_IOSSTATE_TX_LAST_RXE)

		/* LPC */
		PAD_CFG_NF(LPC_ILB_SERIRQ, UP_20K, DEEP, NF1) /* LPC_SERIRQ */
		PAD_CFG_NF(LPC_CLKOUT0, NONE, DEEP, NF1) /* LPC_CLKOUT0 */
		PAD_CFG_NF(LPC_CLKOUT1, UP_20K, DEEP, NF1)
		PAD_CFG_NF(LPC_AD0, UP_20K, DEEP, NF1)	 /* LPC_AD0 */
		PAD_CFG_NF(LPC_AD1, UP_20K, DEEP, NF1)	 /* LPC_AD1 */
		PAD_CFG_NF(LPC_AD2, UP_20K, DEEP, NF1)	 /* LPC_AD2 */
		PAD_CFG_NF(LPC_AD3, UP_20K, DEEP, NF1)	 /* LPC_AD3 */
		PAD_CFG_NF(LPC_CLKRUNB, UP_20K, DEEP, NF1) /* LPC_CLKRUN_N */
		PAD_CFG_NF(LPC_FRAMEB, NATIVE, DEEP, NF1) /* LPC_FRAME_N */

		PAD_CFG_GPI(GPIO_101, NONE, DEEP) /* FST_IO2 -- MEM_CONFIG0 */
		PAD_CFG_GPI(GPIO_102, NONE, DEEP) /* FST_IO3 -- MEM_CONFIG1 */
		PAD_CFG_GPI(GPIO_38, NONE, DEEP) /* LPSS_UART0_RXD - MEM_CONFIG2*/
		PAD_CFG_GPI(GPIO_45, NONE, DEEP) /* LPSS_UART1_CTS - MEM_CONFIG3 */
		>;
};

&fsp_m {
	fspm,package = <PACKAGE_BGA>;
	fspm,profile = <PROFILE_LPDDR4_2400_24_22_22>;
	fspm,memory-down = <MEMORY_DOWN_YES>;
	fspm,scrambler-support = <1>;
	fspm,interleaved-mode = <INTERLEAVED_MODE_ENABLE>;
	fspm,channel-hash-mask = <0x36>;
	fspm,slice-hash-mask = <0x9>;
	fspm,dual-rank-support-enable = <1>;
	fspm,low-memory-max-value = <2048>;
	fspm,ch0-rank-enable = <1>;
	fspm,ch0-device-width = <CHX_DEVICE_WIDTH_X16>;
	fspm,ch0-dram-density = <CHX_DEVICE_DENSITY_8GB>;
	fspm,ch0-option = <(CHX_OPTION_RANK_INTERLEAVING |
			   CHX_OPTION_BANK_ADDRESS_HASHING_ENABLE)>;
	fspm,ch0-odt-config = <CHX_ODT_CONFIG_DDR4_CA_ODT>;
	fspm,ch1-rank-enable = <1>;
	fspm,ch1-device-width = <CHX_DEVICE_WIDTH_X16>;
	fspm,ch1-dram-density = <CHX_DEVICE_DENSITY_8GB>;
	fspm,ch1-option = <(CHX_OPTION_RANK_INTERLEAVING |
			   CHX_OPTION_BANK_ADDRESS_HASHING_ENABLE)>;
	fspm,ch1-odt-config = <CHX_ODT_CONFIG_DDR4_CA_ODT>;
	fspm,ch2-rank-enable = <1>;
	fspm,ch2-device-width = <CHX_DEVICE_WIDTH_X16>;
	fspm,ch2-dram-density = <CHX_DEVICE_DENSITY_8GB>;
	fspm,ch2-option = <(CHX_OPTION_RANK_INTERLEAVING |
			   CHX_OPTION_BANK_ADDRESS_HASHING_ENABLE)>;
	fspm,ch2-odt-config = <CHX_ODT_CONFIG_DDR4_CA_ODT>;
	fspm,ch3-rank-enable = <1>;
	fspm,ch3-device-width = <CHX_DEVICE_WIDTH_X16>;
	fspm,ch3-dram-density = <CHX_DEVICE_DENSITY_8GB>;
	fspm,ch3-option = <(CHX_OPTION_RANK_INTERLEAVING |
			   CHX_OPTION_BANK_ADDRESS_HASHING_ENABLE)>;
	fspm,ch3-odt-config = <CHX_ODT_CONFIG_DDR4_CA_ODT>;
	fspm,fspm,skip-cse-rbp = <1>;

	fspm,ch-bit-swizzling = /bits/ 8 <
		/* LP4_PHYS_CH0A */

		/* DQA[0:7] pins of LPDDR4 module */
		6 7 5 4 3 1 0 2
		/* DQA[8:15] pins of LPDDR4 module */
		12 10 11 13 14 8 9 15
		/* DQB[0:7] pins of LPDDR4 module with offset of 16 */
		16 22 23 20 18 17 19 21
		/* DQB[7:15] pins of LPDDR4 module with offset of 16 */
		30 28 29 25 24 26 27 31

		/* LP4_PHYS_CH0B */
		/* DQA[0:7] pins of LPDDR4 module */
		7 3 5 2 6 0 1 4
		/* DQA[8:15] pins of LPDDR4 module */
		 9 14 12 13 10 11 8 15
		/* DQB[0:7] pins of LPDDR4 module with offset of 16 */
		20 22 23 16 19 17 18 21
		/* DQB[7:15] pins of LPDDR4 module with offset of 16 */
		28 24 26 27 29 30 31 25

		/* LP4_PHYS_CH1A */

		/* DQA[0:7] pins of LPDDR4 module */
		2 1 6 7 5 4 3 0
		/* DQA[8:15] pins of LPDDR4 module */
		11 10 8 9 12 15 13 14
		/* DQB[0:7] pins of LPDDR4 module with offset of 16 */
		17 23 19 16 21 22 20 18
		/* DQB[7:15] pins of LPDDR4 module with offset of 16 */
		31 29 26 25 28 27 24 30

		/* LP4_PHYS_CH1B */

		/* DQA[0:7] pins of LPDDR4 module */
		4 3 7 5 6 1 0 2
		/* DQA[8:15] pins of LPDDR4 module */
		15 9 8 11 14 13 12 10
		/* DQB[0:7] pins of LPDDR4 module with offset of 16 */
		20 23 22 21 18 19 16 17
		/* DQB[7:15] pins of LPDDR4 module with offset of 16 */
		25 28 30 31 26 27 24 29>;

	fspm,dimm0-spd-address = <0>;
	fspm,dimm1-spd-address = <0>;
	fspm,skip-cse-rbp = <1>;
	fspm,enable-s3-heci2 = <0>;
};

&fsp_s {
	bootph-some-ram;

	fsps,ish-enable = <0>;
	fsps,enable-sata = <0>;
	fsps,i2c6-enable = <I2CX_ENABLE_DISABLED>;
	fsps,i2c7-enable = <I2CX_ENABLE_DISABLED>;
	fsps,hsuart3-enable = <HSUARTX_ENABLE_DISABLED>;
	fsps,spi1-enable = <SPIX_ENABLE_DISABLED>;
	fsps,spi2-enable = <SPIX_ENABLE_DISABLED>;
	fsps,sdio-enabled = <0>;

	/* Disable unused clkreq of PCIe root ports */
	fsps,pcie-rp-clk-req-number = /bits/ 8 <0 /* wifi/bt */
		CLKREQ_DISABLED
		CLKREQ_DISABLED
		CLKREQ_DISABLED
		CLKREQ_DISABLED
		CLKREQ_DISABLED>;

	/*
	 * GPIO for PERST_0
	 * If the Board has PERST_0 signal, assign the GPIO
	 * If the Board does not have PERST_0, assign GPIO_PRT0_UDEF
	 *
	 * This are not used yet, so comment them out for now.
	 *
	 * prt0-gpio = <GPIO_122>;
	 *
	 * GPIO for SD card detect
	 * sdcard-cd-gpio = <GPIO_177>;
	 */

	/*
	 * Order is emmc-tx-data-cntl1, emmc-tx-data-cntl2,
	 * emmc-rx-cmd-data-cntl1, emmc-rx-cmd-data-cntl2
	 *
	 * EMMC TX DATA Delay 1
	 * Refer to EDS-Vol2-22.3
	 * [14:8] steps of delay for HS400, each 125ps
	 * [6:0] steps of delay for SDR104/HS200, each 125ps
	 */

	/*
	 * EMMC TX DATA Delay 2
	 * Refer to EDS-Vol2-22.3.
	 * [30:24] steps of delay for SDR50, each 125ps
	 * [22:16] steps of delay for DDR50, each 125ps
	 * [14:8] steps of delay for SDR25/HS50, each 125ps
	 * [6:0] steps of delay for SDR12, each 125ps
	 */

	/*
	 * EMMC RX CMD/DATA Delay 1
	 * Refer to EDS-Vol2-22.3.
	 * [30:24] steps of delay for SDR50, each 125ps
	 * [22:16] steps of delay for DDR50, each 125ps
	 * [14:8] steps of delay for SDR25/HS50, each 125ps
	 * [6:0] steps of delay for SDR12, each 125ps
	 */

	/*
	 * EMMC RX CMD/DATA Delay 2
	 * Refer to EDS-Vol2-22.3.
	 * [17:16] stands for Rx Clock before Output Buffer
	 * [14:8] steps of delay for Auto Tuning Mode, each 125ps
	 * [6:0] steps of delay for HS200, each 125ps
	 */
	/* Enable DPTF */
	fsps,dptf-enabled;
	fsps,emmc-tx-data-cntl1 = <0x0c16>;
	fsps,emmc-tx-data-cntl2 = <0x28162828>;
	fsps,emmc-rx-cmd-data-cntl1 = <0x00181717>;
	fsps,emmc-rx-cmd-data-cntl2 = <0x10008>;

	/* Enable Audio Clock and Power gating */
	fsps,hd-audio-clk-gate = <1>;
	fsps,hd-audio-pwr-gate = <1>;
	fsps,bios-cfg-lock-down = <1>;

	/* Enable WiFi */
	fsps,pcie-root-port-en = [01 00 00 00 00 00];
	fsps,pcie-rp-hot-plug = [00 00 00 00 00 00];

	fsps,skip-mp-init = <1>;
	fsps,spi-eiss = <0>;
	fsps,rtc-lock = <0>;

	fsps,port-usb20-per-port-pe-txi-set = [07 07 06 06 07 07 07 01];
	fsps,port-usb20-per-port-txi-set = [00 02 00 00 00 00 00 03];

	fsps,lpss-s0ix-enable = <1>;
	fsps,usb-otg = <0>;
	fsps,monitor-mwait-enable = <0>;

	/*
	 * TODO(sjg@chromium.org): Move this to the I2C nodes
	 * Intel Common SoC Config
	 *+-------------------+---------------------------+
	 *| Field             |  Value                    |
	 *+-------------------+---------------------------+
	 *| I2C0              | Audio                     |
	 *| I2C2              | TPM                       |
	 *| I2C3              | Touchscreen               |
	 *| I2C4              | Trackpad                  |
	 *| I2C5              | Digitizer                 |
	 *+-------------------+---------------------------+
	 *
	common_soc_config" = "{
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
			.rise-time-ns = 104,
			.fall-time-ns = 52,
		},
		.i2c[2] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST,
			.rise-time-ns = 57,
			.fall-time-ns = 28,
		},
		.i2c[3] = {
			.speed = I2C_SPEED_FAST,
			.rise-time-ns = 76,
			.fall-time-ns = 164,
		},
		.i2c[4] = {
			.speed = I2C_SPEED_FAST,
			.rise-time-ns = 114,
			.fall-time-ns = 164,
			.data_hold_time_ns = 350,
		},
		.i2c[5] = {
			.speed = I2C_SPEED_FAST,
			.rise-time-ns = 152,
			.fall-time-ns = 30,
		},
	}"
	*/

	/* Minimum SLP S3 assertion width 28ms */
	slp-s3-assertion-width-usecs = <28000>;

	pads = <
		/* PCIE_WAKE[0:3]_N */
		PAD_CFG_GPI_SCI_LOW(GPIO_205, UP_20K, DEEP, EDGE_SINGLE) /* WLAN */
		PAD_CFG_GPI(GPIO_206, UP_20K, DEEP)	 /* Unused */
		PAD_CFG_GPI(GPIO_207, UP_20K, DEEP)	 /* Unused */
		PAD_CFG_GPI(GPIO_208, UP_20K, DEEP)	 /* Unused */

		/* EMMC interface */
		PAD_CFG_NF(GPIO_156, DN_20K, DEEP, NF1) /* EMMC_CLK */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_157, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D0 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_158, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D1 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_159, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D2 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_160, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D3 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_161, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D4 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_162, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D5 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_163, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D6 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_164, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_D7 */
		PAD_CFG_NF_IOSSTATE_IOSTERM(GPIO_165, UP_20K, DEEP, NF1, HIZCRX1, DISPUPD) /* EMMC_CMD */
		PAD_CFG_NF(GPIO_182, DN_20K, DEEP, NF1) /* EMMC_RCLK */

		/* SDIO -- unused */
		PAD_CFG_GPI(GPIO_166, UP_20K, DEEP)	 /* SDIO_CLK */
		PAD_CFG_GPI(GPIO_167, UP_20K, DEEP)	 /* SDIO_D0 */
		/* Configure SDIO to enable power gating */
		PAD_CFG_NF(GPIO_168, UP_20K, DEEP, NF1)	/* SDIO_D1 */
		PAD_CFG_GPI(GPIO_169, UP_20K, DEEP)	 /* SDIO_D2 */
		PAD_CFG_GPI(GPIO_170, UP_20K, DEEP)	 /* SDIO_D3 */
		PAD_CFG_GPI(GPIO_171, UP_20K, DEEP)	 /* SDIO_CMD */

		/* SDCARD */
		/* Pull down clock by 20K */
		PAD_CFG_NF(GPIO_172, DN_20K, DEEP, NF1) /* SDCARD_CLK */
		PAD_CFG_NF(GPIO_173, UP_20K, DEEP, NF1) /* SDCARD_D0 */
		PAD_CFG_NF(GPIO_174, UP_20K, DEEP, NF1) /* SDCARD_D1 */
		PAD_CFG_NF(GPIO_175, UP_20K, DEEP, NF1) /* SDCARD_D2 */
		PAD_CFG_NF(GPIO_176, UP_20K, DEEP, NF1) /* SDCARD_D3 */
		/* Card detect is active LOW with external pull up */
		PAD_CFG_NF(GPIO_177, NONE, DEEP, NF1) /* SDCARD_CD_N */
		PAD_CFG_NF(GPIO_178, UP_20K, DEEP, NF1) /* SDCARD_CMD */
		/* CLK feedback, internal signal, needs 20K pull down */
		PAD_CFG_NF(GPIO_179, DN_20K, DEEP, NF1) /* SDCARD_CLK_FB */
		/* No h/w write proect for uSD cards, pull down by 20K */
		PAD_CFG_NF(GPIO_186, DN_20K, DEEP, NF1) /* SDCARD_LVL_WP */
		/* EN_SD_SOCKET_PWR_L for SD slot power control. Default on */
		PAD_CFG_GPO(GPIO_183, 0, DEEP)		 /* SDIO_PWR_DOWN_N */

		/* SMBus -- unused */
		PAD_CFG_GPI(SMB_ALERTB, UP_20K, DEEP)	 /* SMB_ALERT _N */
		PAD_CFG_GPI(SMB_CLK, UP_20K, DEEP)	 /* SMB_CLK */
		PAD_CFG_GPI(SMB_DATA, UP_20K, DEEP)	 /* SMB_DATA */

		/* LPC */
		PAD_CFG_NF(LPC_ILB_SERIRQ, UP_20K, DEEP, NF1) /* LPC_SERIRQ */
		PAD_CFG_NF(LPC_CLKOUT0, NONE, DEEP, NF1) /* LPC_CLKOUT0 */
		PAD_CFG_NF(LPC_CLKOUT1, UP_20K, DEEP, NF1)
		PAD_CFG_NF(LPC_AD0, UP_20K, DEEP, NF1)	 /* LPC_AD0 */
		PAD_CFG_NF(LPC_AD1, UP_20K, DEEP, NF1)	 /* LPC_AD1 */
		PAD_CFG_NF(LPC_AD2, UP_20K, DEEP, NF1)	 /* LPC_AD2 */
		PAD_CFG_NF(LPC_AD3, UP_20K, DEEP, NF1)	 /* LPC_AD3 */
		PAD_CFG_NF(LPC_CLKRUNB, UP_20K, DEEP, NF1) /* LPC_CLKRUN_N */
		PAD_CFG_NF(LPC_FRAMEB, NATIVE, DEEP, NF1) /* LPC_FRAME_N */

		/* I2C0 - Audio */
		PAD_CFG_NF(GPIO_124, UP_2K, DEEP, NF1) /* LPSS_I2C0_SDA */
		PAD_CFG_NF(GPIO_125, UP_2K, DEEP, NF1) /* LPSS_I2C0_SCL */

		/* I2C1 - NFC with external pulls */
		PAD_CFG_NF(GPIO_126, NONE, DEEP, NF1) /* LPSS_I2C1_SDA */
		PAD_CFG_NF(GPIO_127, NONE, DEEP, NF1) /* LPSS_I2C1_SCL */

		/* I2C2 - TPM  */
		PAD_CFG_NF(GPIO_128, UP_2K, DEEP, NF1) /* LPSS_I2C2_SDA */
		PAD_CFG_NF(GPIO_129, UP_2K, DEEP, NF1) /* LPSS_I2C2_SCL */

		/* I2C3 - touch */
		PAD_CFG_NF(GPIO_130, UP_2K, DEEP, NF1) /* LPSS_I2C3_SDA */
		PAD_CFG_NF(GPIO_131, UP_2K, DEEP, NF1) /* LPSS_I2C3_SCL */

		/* I2C4 - trackpad */
		/* LPSS_I2C4_SDA */
		PAD_CFG_NF_IOSSTATE(GPIO_132, UP_2K, DEEP, NF1, HIZCRX1)
		/* LPSS_I2C4_SCL */
		PAD_CFG_NF_IOSSTATE(GPIO_133, UP_2K, DEEP, NF1, HIZCRX1)

		/* I2C5 -- pen with external pulls  */
		PAD_CFG_NF(GPIO_134, NONE, DEEP, NF1) /* LPSS_I2C5_SDA */
		PAD_CFG_NF(GPIO_135, NONE, DEEP, NF1) /* LPSS_I2C5_SCL */

		/* I2C6-7 -- unused */
		PAD_CFG_GPI(GPIO_136, UP_20K, DEEP)	 /* LPSS_I2C6_SDA */
		PAD_CFG_GPI(GPIO_137, UP_20K, DEEP)	 /* LPSS_I2C6_SCL */
		PAD_CFG_GPI(GPIO_138, UP_20K, DEEP)	 /* LPSS_I2C7_SDA */
		PAD_CFG_GPI(GPIO_139, UP_20K, DEEP)	 /* LPSS_I2C7_SCL */

		/* Audio Amp - I2S6 */
		PAD_CFG_NF(GPIO_146, NATIVE, DEEP, NF2) /* ISH_GPIO_0 - I2S6_BCLK */
		PAD_CFG_NF(GPIO_147, NATIVE, DEEP, NF2) /* ISH_GPIO_1 - I2S6_WS_SYNC */
		PAD_CFG_GPI(GPIO_148, UP_20K, DEEP)	 /* ISH_GPIO_2 - unused */
		PAD_CFG_NF(GPIO_149, NATIVE, DEEP, NF2) /* ISH_GPIO_3 - I2S6_SDO */

		/* NFC Reset */
		PAD_CFG_GPO(GPIO_150, 1, DEEP)		 /* ISH_GPIO_4 */

		PAD_CFG_GPI(GPIO_151, UP_20K, DEEP)	 /* ISH_GPIO_5 - unused */

		/* Touch enable */
		PAD_CFG_GPO(GPIO_152, 1, DEEP)		 /* ISH_GPIO_6 */

		PAD_CFG_GPI(GPIO_153, UP_20K, DEEP)	 /* ISH_GPIO_7 - unused */
		PAD_CFG_GPI(GPIO_154, UP_20K, DEEP)	 /* ISH_GPIO_8 - unused */
		PAD_CFG_GPI(GPIO_155, UP_20K, DEEP)	 /* ISH_GPIO_9 - unused */

		/* PCIE_CLKREQ[0:3]_N */
		PAD_CFG_NF(GPIO_209, NONE, DEEP, NF1)	 /* WLAN with external pull */
		PAD_CFG_GPI(GPIO_210, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_211, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_212, UP_20K, DEEP)	 /* unused */

		/* OSC_CLK_OUT_[0:4] -- unused */
		PAD_CFG_GPI(OSC_CLK_OUT_0, UP_20K, DEEP)
		PAD_CFG_GPI(OSC_CLK_OUT_1, UP_20K, DEEP)
		PAD_CFG_GPI(OSC_CLK_OUT_2, UP_20K, DEEP)
		PAD_CFG_GPI(OSC_CLK_OUT_3, UP_20K, DEEP)
		PAD_CFG_GPI(OSC_CLK_OUT_4, UP_20K, DEEP)

		/* PMU Signals */
		PAD_CFG_GPI(PMU_AC_PRESENT, UP_20K, DEEP) /* PMU_AC_PRESENT - unused */
		PAD_CFG_NF(PMU_BATLOW_B, UP_20K, DEEP, NF1) /* PMU_BATLOW_N */
		PAD_CFG_NF(PMU_PLTRST_B, NONE, DEEP, NF1) /* PMU_PLTRST_N */
		PAD_CFG_NF(PMU_PWRBTN_B, UP_20K, DEEP, NF1) /* PMU_PWRBTN_N */
		PAD_CFG_NF(PMU_RESETBUTTON_B, NONE, DEEP, NF1) /* PMU_RSTBTN_N */
		PAD_CFG_NF_IOSSTATE(PMU_SLP_S0_B, NONE, DEEP, NF1, IGNORE) /* PMU_SLP_S0_N */
		PAD_CFG_NF(PMU_SLP_S3_B, NONE, DEEP, NF1) /* PMU_SLP_S3_N */
		PAD_CFG_NF(PMU_SLP_S4_B, NONE, DEEP, NF1) /* PMU_SLP_S4_N */
		PAD_CFG_NF(PMU_SUSCLK, NONE, DEEP, NF1) /* PMU_SUSCLK */
		PAD_CFG_GPO(PMU_WAKE_B, 1, DEEP)	 /* EN_PP3300_EMMC */
		PAD_CFG_NF(SUS_STAT_B, NONE, DEEP, NF1) /* SUS_STAT_N */
		PAD_CFG_NF(SUSPWRDNACK, NONE, DEEP, NF1) /* SUSPWRDNACK */

		/* DDI[0:1] SDA and SCL -- unused */
		PAD_CFG_GPI(GPIO_187, UP_20K, DEEP)	 /* HV_DDI0_DDC_SDA */
		PAD_CFG_GPI(GPIO_188, UP_20K, DEEP)	 /* HV_DDI0_DDC_SCL */
		PAD_CFG_GPI(GPIO_189, UP_20K, DEEP)	 /* HV_DDI1_DDC_SDA */
		PAD_CFG_GPI(GPIO_190, UP_20K, DEEP)	 /* HV_DDI1_DDC_SCL */

		/* MIPI I2C -- unused */
		PAD_CFG_GPI(GPIO_191, UP_20K, DEEP)	 /* MIPI_I2C_SDA */
		PAD_CFG_GPI(GPIO_192, UP_20K, DEEP)	 /* MIPI_I2C_SCL */

		/* Panel 0 control */
		PAD_CFG_NF(GPIO_193, NATIVE, DEEP, NF1) /* PNL0_VDDEN */
		PAD_CFG_NF(GPIO_194, NATIVE, DEEP, NF1) /* PNL0_BKLTEN */
		PAD_CFG_NF(GPIO_195, NATIVE, DEEP, NF1) /* PNL0_BKLTCTL */

		/* Panel 1 control -- unused */
		PAD_CFG_NF(GPIO_196, NATIVE, DEEP, NF1) /* PNL1_VDDEN */
		PAD_CFG_NF(GPIO_197, NATIVE, DEEP, NF1) /* PNL1_BKLTEN */
		PAD_CFG_NF(GPIO_198, NATIVE, DEEP, NF1) /* PNL1_BKLTCTL */

		/* Hot plug detect */
		PAD_CFG_NF(GPIO_199, UP_20K, DEEP, NF2) /* HV_DDI1_HPD */
		PAD_CFG_NF(GPIO_200, UP_20K, DEEP, NF2) /* HV_DDI0_HPD */

		/* MDSI signals -- unused */
		PAD_CFG_GPI(GPIO_201, UP_20K, DEEP)	 /* MDSI_A_TE */
		PAD_CFG_GPI(GPIO_202, UP_20K, DEEP)	 /* MDSI_A_TE */

		/* USB overcurrent pins */
		PAD_CFG_NF(GPIO_203, UP_20K, DEEP, NF1) /* USB_OC0_N */
		PAD_CFG_NF(GPIO_204, UP_20K, DEEP, NF1) /* USB_OC1_N */

		/* PMC SPI -- almost entirely unused */
		PAD_CFG_GPI(PMC_SPI_FS0, UP_20K, DEEP)
		PAD_CFG_NF(PMC_SPI_FS1, UP_20K, DEEP, NF2) /* HV_DDI2_HPD -- EDP HPD */
		PAD_CFG_GPI(PMC_SPI_FS2, UP_20K, DEEP)
		PAD_CFG_GPI(PMC_SPI_RXD, UP_20K, DEEP)
		PAD_CFG_GPI(PMC_SPI_TXD, UP_20K, DEEP)
		PAD_CFG_GPI(PMC_SPI_CLK, UP_20K, DEEP)

		/* PMIC Signals Unused signals related to an old PMIC interface */
		PAD_CFG_NF_IOSSTATE(PMIC_RESET_B, NATIVE, DEEP, NF1, IGNORE) /* PMIC_RESET_B */
		PAD_CFG_GPI(GPIO_213, NONE, DEEP)	 /* unused external pull */
		PAD_CFG_GPI(GPIO_214, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_215, UP_20K, DEEP)	 /* unused */
		PAD_CFG_NF(PMIC_THERMTRIP_B, UP_20K, DEEP, NF1) /* THERMTRIP_N */
		PAD_CFG_GPI(PMIC_STDBY, UP_20K, DEEP)	 /* unused */
		PAD_CFG_NF(PROCHOT_B, UP_20K, DEEP, NF1) /* PROCHOT_N */
		PAD_CFG_NF(PMIC_I2C_SCL, UP_1K, DEEP, NF1) /* PMIC_I2C_SCL */
		PAD_CFG_NF(PMIC_I2C_SDA, UP_1K, DEEP, NF1) /* PMIC_I2C_SDA */

		/* I2S1 -- largely unused */
		PAD_CFG_GPI(GPIO_74, UP_20K, DEEP)	/* I2S1_MCLK */
		PAD_CFG_GPI(GPIO_75, UP_20K, DEEP)	/* I2S1_BCLK -- PCH_WP */
		PAD_CFG_GPO(GPIO_76, 0, DEEP)		/* I2S1_WS_SYNC -- SPK_PA_EN */
		PAD_CFG_GPI(GPIO_77, UP_20K, DEEP)	/* I2S1_SDI */
		PAD_CFG_GPO(GPIO_78, 1, DEEP)		/* I2S1_SDO -- EN_PP3300_DX_LTE_SOC */

		/* DMIC or I2S4 */
		/* AVS_DMIC_CLK_A1 */
		PAD_CFG_NF_IOSSTATE(GPIO_79, NATIVE, DEEP, NF1, IGNORE)
		PAD_CFG_NF(GPIO_80, NATIVE, DEEP, NF1) /* AVS_DMIC_CLK_B1 */
		PAD_CFG_NF(GPIO_81, NATIVE, DEEP, NF1)	/* AVS_DMIC_DATA_1 */
		PAD_CFG_GPI(GPIO_82, DN_20K, DEEP)	 /* unused -- strap */
		PAD_CFG_NF(GPIO_83, NATIVE, DEEP, NF1) /* AVS_DMIC_DATA_2 */

		/* I2S2 -- Headset amp */
		PAD_CFG_NF(GPIO_84, NATIVE, DEEP, NF1)	 /* AVS_I2S2_MCLK */
		PAD_CFG_NF(GPIO_85, NATIVE, DEEP, NF1)	 /* AVS_I2S2_BCLK */
		PAD_CFG_NF(GPIO_86, NATIVE, DEEP, NF1)	 /* AVS_I2S2_SW_SYNC */
		PAD_CFG_NF(GPIO_87, NATIVE, DEEP, NF1)	 /* AVS_I2S2_SDI */
		PAD_CFG_NF(GPIO_88, NATIVE, DEEP, NF1)	 /* AVS_I2S2_SDO */

		/* I2S3 -- largely unused */
		PAD_CFG_GPI(GPIO_89, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_90, UP_20K, DEEP)	 /* GPS_HOST_WAKE */
		PAD_CFG_GPO(GPIO_91, 1, DEEP)		 /* GPS_EN */
		PAD_CFG_GPI(GPIO_92, DN_20K, DEEP)	 /* unused -- strap */

		/* Fast SPI */
		PAD_CFG_NF_IOSSTATE(GPIO_97, NATIVE, DEEP, NF1, IGNORE)	/* FST_SPI_CS0_B */
		PAD_CFG_GPI(GPIO_98, UP_20K, DEEP)				/* FST_SPI_CS1_B -- unused */
		PAD_CFG_NF_IOSSTATE(GPIO_99, NATIVE, DEEP, NF1, IGNORE)	/* FST_SPI_MOSI_IO0 */
		PAD_CFG_NF_IOSSTATE(GPIO_100, NATIVE, DEEP, NF1, IGNORE)	/* FST_SPI_MISO_IO1 */
		PAD_CFG_GPI(GPIO_101, NONE, DEEP)				/* FST_IO2 -- MEM_CONFIG0 */
		PAD_CFG_GPI(GPIO_102, NONE, DEEP)				/* FST_IO3 -- MEM_CONFIG1 */
		PAD_CFG_NF_IOSSTATE(GPIO_103, NATIVE, DEEP, NF1, IGNORE)	/* FST_SPI_CLK */
		PAD_CFG_NF_IOSSTATE(FST_SPI_CLK_FB, NATIVE, DEEP, NF1, IGNORE) /* FST_SPI_CLK_FB */
		PAD_CFG_NF_IOSSTATE(GPIO_106, NATIVE, DEEP, NF3, IGNORE)	/* FST_SPI_CS2_N */

		/* SIO_SPI_0 - Used for FP */
		PAD_CFG_NF(GPIO_104, NATIVE, DEEP, NF1)			/* SIO_SPI_0_CLK */
		PAD_CFG_NF(GPIO_105, NATIVE, DEEP, NF1)			/* SIO_SPI_0_FS0 */
		PAD_CFG_NF(GPIO_109, NATIVE, DEEP, NF1)			/* SIO_SPI_0_RXD */
		PAD_CFG_NF(GPIO_110, NATIVE, DEEP, NF1)			/* SIO_SPI_0_TXD */

		/* SIO_SPI_1 -- largely unused */
		PAD_CFG_GPI(GPIO_111, UP_20K, DEEP)	 /* SIO_SPI_1_CLK */
		PAD_CFG_GPI(GPIO_112, UP_20K, DEEP)	 /* SIO_SPI_1_FS0 */
		PAD_CFG_GPI(GPIO_113, UP_20K, DEEP)	 /* SIO_SPI_1_FS1 */
		/* Headset interrupt */
		PAD_CFG_GPI_APIC_LOW(GPIO_116, NONE, DEEP) /* SIO_SPI_1_RXD */
		PAD_CFG_GPI(GPIO_117, UP_20K, DEEP)	 /* SIO_SPI_1_TXD */

		/* SIO_SPI_2 -- unused */
		PAD_CFG_GPI(GPIO_118, UP_20K, DEEP)	 /* SIO_SPI_2_CLK */
		PAD_CFG_GPI(GPIO_119, UP_20K, DEEP)	 /* SIO_SPI_2_FS0 */
		PAD_CFG_GPI(GPIO_120, UP_20K, DEEP)	 /* SIO_SPI_2_FS1 */
		PAD_CFG_GPI(GPIO_121, UP_20K, DEEP)	 /* SIO_SPI_2_FS2 */
		/* WLAN_PE_RST - default to deasserted */
		PAD_CFG_GPO(GPIO_122, 0, DEEP)		 /* SIO_SPI_2_RXD */
		PAD_CFG_GPI(GPIO_123, UP_20K, DEEP)	 /* SIO_SPI_2_TXD */

		/* Debug tracing */
		PAD_CFG_GPI(GPIO_0, UP_20K, DEEP)
		PAD_CFG_GPI(GPIO_1, UP_20K, DEEP)
		PAD_CFG_GPI(GPIO_2, UP_20K, DEEP)
		PAD_CFG_GPI_SCI_HIGH(GPIO_3, DN_20K, DEEP, LEVEL)	 /* FP_INT */
		PAD_CFG_GPI(GPIO_4, UP_20K, DEEP)
		PAD_CFG_GPI(GPIO_5, UP_20K, DEEP)
		PAD_CFG_GPI(GPIO_6, UP_20K, DEEP)
		PAD_CFG_GPI(GPIO_7, UP_20K, DEEP)
		PAD_CFG_GPI(GPIO_8, UP_20K, DEEP)

		PAD_CFG_GPI_APIC_LOW(GPIO_9, NONE, DEEP) /* dTPM IRQ */
		PAD_CFG_GPI(GPIO_10, DN_20K, DEEP)	 /* Board phase enforcement */
		PAD_CFG_GPI_SCI_LOW(GPIO_11, NONE, DEEP, EDGE_SINGLE) /* EC SCI  */
		PAD_CFG_GPI(GPIO_12, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI_APIC_LOW(GPIO_13, NONE, DEEP) /* PEN_INT_ODL */
		PAD_CFG_GPI_APIC_HIGH(GPIO_14, DN_20K, DEEP) /* FP_INT */
		PAD_CFG_GPI_SCI_LOW(GPIO_15, NONE, DEEP, EDGE_SINGLE)	 /* TRACKPAD_INT_1V8_ODL */
		PAD_CFG_GPI(GPIO_16, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_17, UP_20K, DEEP)	 /* 1 vs 4 DMIC config */
		PAD_CFG_GPI_APIC_LOW(GPIO_18, NONE, DEEP) /* Trackpad IRQ */
		PAD_CFG_GPI(GPIO_19, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI_APIC_LOW(GPIO_20, UP_20K, DEEP) /* NFC IRQ */
		PAD_CFG_GPI_APIC_LOW(GPIO_21, NONE, DEEP) /* Touch IRQ */
		PAD_CFG_GPI_SCI_LOW(GPIO_22, NONE, DEEP, EDGE_SINGLE) /* EC wake */
		PAD_CFG_GPI(GPIO_23, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_24, NONE, DEEP)	 /* PEN_PDCT_ODL */
		PAD_CFG_GPI(GPIO_25, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_26, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI(GPIO_27, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPI_APIC_LOW(GPIO_28, NONE, DEEP) /* TPM IRQ */
		PAD_CFG_GPO(GPIO_29, 1, DEEP)		 /* FP reset */
		PAD_CFG_GPI_APIC_LOW(GPIO_30, NONE, DEEP) /* KB IRQ */
		PAD_CFG_GPO(GPIO_31, 0, DEEP)		 /* NFC FW DL */
		PAD_CFG_NF(GPIO_32, NONE, DEEP, NF5)	 /* SUS_CLK2 */
		PAD_CFG_GPI_APIC_LOW(GPIO_33, NONE, DEEP) /* PMIC IRQ */
		PAD_CFG_GPI(GPIO_34, UP_20K, DEEP)	 /* unused */
		PAD_CFG_GPO(GPIO_35, 0, DEEP)		 /* PEN_RESET - active high */
		PAD_CFG_GPO(GPIO_36, 0, DEEP)		 /* touch reset */
		PAD_CFG_GPI(GPIO_37, UP_20K, DEEP)	 /* unused */

		/* LPSS_UART[0:2] */
		PAD_CFG_GPI(GPIO_38, NONE, DEEP)	 /* LPSS_UART0_RXD - MEM_CONFIG2*/
		/* Next 2 are straps */
		PAD_CFG_GPI(GPIO_39, DN_20K, DEEP)	 /* LPSS_UART0_TXD - unused */
		PAD_CFG_GPI(GPIO_40, DN_20K, DEEP)	 /* LPSS_UART0_RTS - unused */
		PAD_CFG_GPI(GPIO_41, NONE, DEEP)	 /* LPSS_UART0_CTS - EC_IN_RW */
		PAD_CFG_NF(GPIO_42, NATIVE, DEEP, NF1)	 /* LPSS_UART1_RXD */
		PAD_CFG_NF(GPIO_43, NATIVE, DEEP, NF1)	 /* LPSS_UART1_TXD */
		PAD_CFG_GPO(GPIO_44, 1, DEEP)	 /* GPS_RST_ODL */
		PAD_CFG_GPI(GPIO_45, NONE, DEEP)	 /* LPSS_UART1_CTS - MEM_CONFIG3 */
		PAD_CFG_NF(GPIO_46, NATIVE, DEEP, NF1)	 /* LPSS_UART2_RXD */
		PAD_CFG_NF_IOSSTATE(GPIO_47, NATIVE, DEEP, NF1, TX1_RX_DCR_X0) /* UART2 TX */
		PAD_CFG_GPI(GPIO_48, UP_20K, DEEP)	 /* LPSS_UART2_RTS - unused */
		PAD_CFG_GPI_SMI_LOW(GPIO_49, NONE, DEEP, EDGE_SINGLE) /* LPSS_UART2_CTS - EC_SMI_L */

		/* Camera interface -- completely unused */
		PAD_CFG_GPI(GPIO_62, UP_20K, DEEP)	 /* GP_CAMERASB00 */
		PAD_CFG_GPI(GPIO_63, UP_20K, DEEP)	 /* GP_CAMERASB01 */
		PAD_CFG_GPI(GPIO_64, UP_20K, DEEP)	 /* GP_CAMERASB02 */
		PAD_CFG_GPI(GPIO_65, UP_20K, DEEP)	 /* GP_CAMERASB03 */
		PAD_CFG_GPI(GPIO_66, UP_20K, DEEP)	 /* GP_CAMERASB04 */
		PAD_CFG_GPI(GPIO_67, UP_20K, DEEP)	 /* GP_CAMERASB05 */
		PAD_CFG_GPI(GPIO_68, UP_20K, DEEP)	 /* GP_CAMERASB06 */
		PAD_CFG_GPI(GPIO_69, UP_20K, DEEP)	 /* GP_CAMERASB07 */
		PAD_CFG_GPI(GPIO_70, UP_20K, DEEP)	 /* GP_CAMERASB08 */
		PAD_CFG_GPI(GPIO_71, UP_20K, DEEP)	 /* GP_CAMERASB09 */
		PAD_CFG_GPI(GPIO_72, UP_20K, DEEP)	 /* GP_CAMERASB10 */
		PAD_CFG_GPI(GPIO_73, UP_20K, DEEP)	 /* GP_CAMERASB11 */
	>;
};

&rtc {
	#address-cells = <1>;
	#size-cells = <0>;
	bootph-some-ram;
};