CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_ARCH_AT91=y
CONFIG_TEXT_BASE=0x26f00000
CONFIG_SYS_MALLOC_LEN=0x81000
CONFIG_TARGET_AT91SAM9X5EK=y
CONFIG_ATMEL_LEGACY=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x20003ef0
CONFIG_SF_DEFAULT_SPEED=30000000
CONFIG_ENV_SIZE=0x4200
CONFIG_ENV_OFFSET=0x4200
CONFIG_ENV_SECT_SIZE=0x210
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
CONFIG_SYS_MONITOR_LEN=524288
CONFIG_DEBUG_UART_BASE=0xfffff200
CONFIG_DEBUG_UART_CLOCK=132000000
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_DEBUG_UART=y
CONFIG_FIT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=6 root=ubi0:rootfs rw"
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="sf probe 0; sf read 0x22000000 0x84000 0x294000; bootm 0x22000000"
CONFIG_SYS_CBSIZE=256
CONFIG_SYS_PBSIZE=281
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_NAND_TRIMFFS=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_BOOTP_BOOTFILESIZE=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_CMD_MTDPARTS=y
CONFIG_CMD_UBI=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_GPIO=y
CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_ATMEL=y
CONFIG_ATMEL_NAND_HW_PMECC=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_VIDEO=y
# CONFIG_VIDEO_BPP8 is not set
# CONFIG_VIDEO_BPP32 is not set
CONFIG_ATMEL_HLCD=y