ibm,opal/power-mgt/occ device tree entries
==========================================

This node exports the per-chip pstate table properties to kernel.

Example:

.. code-block:: dts

 occ@7ffddf8000 {
        ibm,pstate-vdds = [45 45 46 46 46 47 48 49 4a 4b 4c 4d 4f 50 51 52 53 54 55 57 58 59 5a 5b 5c 5d 5e 5f 5f 60 61 62 63 64 65 65 66 67 68 69 6a 6a 6b 6c 6d 6e 6f 70 70 71];
        ibm,chip-id = <0x1>;
        phandle = <0x100003b8>;
        ibm,pstate-vcss = [3b 3d 3f 41 42 44 45 46 47 48 49 4a 4b 4c 4d 4e 4f 50 50 51 52 53 54 55 56 56 57 57 58 58 59 59 5a 5a 5b 5b 5c 5c 5d 5d 5e 5e 5f 5f 60 60 61 61 62 62];
        reg = <0x7f 0xfddf8000 0xb98>;
 };

ibm,chip-id
-----------

This property denotes the ID of chip to which OCC belongs to.

reg
---

This tuple gives the statring address of the OPAL data in HOMER and
the size of the OPAL data.

The top-level /ibm,opal/power-mgt contains : ::

 #size-cells = <1>
 #address-cells = <2>

ibm,pstate-vcss ibm,pstate-vdds
-------------------------------

These properties list a voltage-identifier of each of the pstates listed in
ibm,pstate-ids for the Vcs and Vdd values used for that pstate in that chip.
Each VID is a single byte.

ibm,opal/power-mgt/freq-domain-mask
-----------------------------------

This property is a bitmask which will have different value depending upon the
generation of the processor. Frequency domain would indicate group of CPUs
which would share same frequency. Bitwise AND is taken between this bitmask
value and PIR of cpu. All the CPUs lying in the same frequency domain will have
same result for AND. Thus frequency management can be done based on frequency
domain. A frequency domain may be a core or a quad, etc depending upon the
generation of the processor.

For example, for POWER8 0xFFF8 indicates core wide frequency domain. Taking AND
with the PIR of CPUs will yield us a frequency domain which is core wide
distribution as last 3 bits have been masked which represent the threads.

For POWER9, 0xFFF0 indicates quad wide frequency domain. Taking AND with
the PIR of CPUs will yield us frequency domain which is quad wise
distribution as last 4 bits have been masked which represent the cores.

ibm,opal/power-mgt/domain-runs-at
---------------------------------

There are two strategies in which the OCC can change the frequency of the cores
in the quad on P9.
1) FREQ_MAX_IN_DOMAIN : the OCC sets the frequency of the quad to the maximum
of the latest frequency requested by each of the component cores.
2) FREQ_MOST_RECENTLY_SET : the OCC sets the frequency of the quad to the most
recent frequency value requested by the CPUs in the quad

In case of P8, the domain is the core and the strategy by default is
FREQ_MOST_RECENTLY_SET since the PMCRs of the threads in the core are mirrored.
However on P9, the domain is quad and the strategy is FREQ_MAX_IN_DOMAIN since
each core has its own PMCR.

domain-runs-at denotes the strategy which OCC is using to change the frequency
of a frequency domain.