hw/pflash_cfi02.c - qemu - Git at Google

 /*
  *  CFI parallel flash with AMD command set emulation
  *
  *  Copyright (c) 2005 Jocelyn Mayer
  *
  * This library is free software; you can redistribute it and/or
  * modify it under the terms of the GNU Lesser General Public
  * License as published by the Free Software Foundation; either
  * version 2 of the License, or (at your option) any later version.
  *
  * This library is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  * Lesser General Public License for more details.
  *
  * You should have received a copy of the GNU Lesser General Public
  * License along with this library; if not, see <http://www.gnu.org/licenses/>.
  */

 /*
  * For now, this code can emulate flashes of 1, 2 or 4 bytes width.
  * Supported commands/modes are:
  * - flash read
  * - flash write
  * - flash ID read
  * - sector erase
  * - chip erase
  * - unlock bypass command
  * - CFI queries
  *
  * It does not support flash interleaving.
  * It does not implement boot blocs with reduced size
  * It does not implement software data protection as found in many real chips
  * It does not implement erase suspend/resume commands
  * It does not implement multiple sectors erase
  */

 #include "hw.h"
 #include "flash.h"
 #include "qemu-timer.h"
 #include "block.h"

 //#define PFLASH_DEBUG
 #ifdef PFLASH_DEBUG
 #define DPRINTF(fmt, ...)                          \
 do {                                               \
     printf("PFLASH: " fmt , ## __VA_ARGS__);       \
 } while (0)
 #else
 #define DPRINTF(fmt, ...) do { } while (0)
 #endif

 struct pflash_t {
     BlockDriverState *bs;
     target_phys_addr_t base;
     uint32_t sector_len;
     uint32_t chip_len;
     int mappings;
     int width;
     int wcycle; /* if 0, the flash is read normally */
     int bypass;
     int ro;
     uint8_t cmd;
     uint8_t status;
     uint16_t ident[4];
     uint16_t unlock_addr[2];
     uint8_t cfi_len;
     uint8_t cfi_table[0x52];
     QEMUTimer *timer;
     ram_addr_t off;
     int fl_mem;
     int rom_mode;
     void *storage;
 };

 static void pflash_register_memory(pflash_t *pfl, int rom_mode)
 {
     unsigned long phys_offset = pfl->fl_mem;
     int i;

     if (rom_mode)
         phys_offset |= pfl->off | IO_MEM_ROMD;
     pfl->rom_mode = rom_mode;

     for (i = 0; i < pfl->mappings; i++)
         cpu_register_physical_memory(pfl->base + i * pfl->chip_len,
                                      pfl->chip_len, phys_offset);
 }

 static void pflash_timer (void *opaque)
 {
     pflash_t *pfl = opaque;

     DPRINTF("%s: command %02x done\n", __func__, pfl->cmd);
     /* Reset flash */
     pfl->status ^= 0x80;
     if (pfl->bypass) {
         pfl->wcycle = 2;
     } else {
         pflash_register_memory(pfl, 1);
         pfl->wcycle = 0;
     }
     pfl->cmd = 0;
 }

 static uint32_t pflash_read (pflash_t *pfl, target_phys_addr_t offset,
                              int width, int be)
 {
     target_phys_addr_t boff;
     uint32_t ret;
     uint8_t *p;

     DPRINTF("%s: offset " TARGET_FMT_plx "\n", __func__, offset);
     ret = -1;
     if (pfl->rom_mode) {
         /* Lazy reset of to ROMD mode */
         if (pfl->wcycle == 0)
             pflash_register_memory(pfl, 1);
     }
     offset &= pfl->chip_len - 1;
     boff = offset & 0xFF;
     if (pfl->width == 2)
         boff = boff >> 1;
     else if (pfl->width == 4)
         boff = boff >> 2;
     switch (pfl->cmd) {
     default:
         /* This should never happen : reset state & treat it as a read*/
         DPRINTF("%s: unknown command state: %x\n", __func__, pfl->cmd);
         pfl->wcycle = 0;
         pfl->cmd = 0;
     case 0x80:
         /* We accept reads during second unlock sequence... */
     case 0x00:
     flash_read:
         /* Flash area read */
         p = pfl->storage;
         switch (width) {
         case 1:
             ret = p[offset];
 //            DPRINTF("%s: data offset %08x %02x\n", __func__, offset, ret);
             break;
         case 2:
             if (be) {
                 ret = p[offset] << 8;
                 ret |= p[offset + 1];
             } else {
                 ret = p[offset];
                 ret |= p[offset + 1] << 8;
             }
 //            DPRINTF("%s: data offset %08x %04x\n", __func__, offset, ret);
             break;
         case 4:
             if (be) {
                 ret = p[offset] << 24;
                 ret |= p[offset + 1] << 16;
                 ret |= p[offset + 2] << 8;
                 ret |= p[offset + 3];
             } else {
                 ret = p[offset];
                 ret |= p[offset + 1] << 8;
                 ret |= p[offset + 2] << 16;
                 ret |= p[offset + 3] << 24;
             }
 //            DPRINTF("%s: data offset %08x %08x\n", __func__, offset, ret);
             break;
         }
         break;
     case 0x90:
         /* flash ID read */
         switch (boff) {
         case 0x00:
         case 0x01:
             ret = pfl->ident[boff & 0x01];
             break;
         case 0x02:
             ret = 0x00; /* Pretend all sectors are unprotected */
             break;
         case 0x0E:
         case 0x0F:
             if (pfl->ident[2 + (boff & 0x01)] == (uint8_t)-1)
                 goto flash_read;
             ret = pfl->ident[2 + (boff & 0x01)];
             break;
         default:
             goto flash_read;
         }
         DPRINTF("%s: ID " TARGET_FMT_pld " %x\n", __func__, boff, ret);
         break;
     case 0xA0:
     case 0x10:
     case 0x30:
         /* Status register read */
         ret = pfl->status;
         DPRINTF("%s: status %x\n", __func__, ret);
         /* Toggle bit 6 */
         pfl->status ^= 0x40;
         break;
     case 0x98:
         /* CFI query mode */
         if (boff > pfl->cfi_len)
             ret = 0;
         else
             ret = pfl->cfi_table[boff];
         break;
     }

     return ret;
 }

 /* update flash content on disk */
 static void pflash_update(pflash_t *pfl, int offset,
                           int size)
 {
     int offset_end;
     if (pfl->bs) {
         offset_end = offset + size;
         /* round to sectors */
         offset = offset >> 9;
         offset_end = (offset_end + 511) >> 9;
         bdrv_write(pfl->bs, offset, pfl->storage + (offset << 9),
                    offset_end - offset);
     }
 }

 static void pflash_write (pflash_t *pfl, target_phys_addr_t offset,
                           uint32_t value, int width, int be)
 {
     target_phys_addr_t boff;
     uint8_t *p;
     uint8_t cmd;

     cmd = value;
     if (pfl->cmd != 0xA0 && cmd == 0xF0) {
 #if 0
         DPRINTF("%s: flash reset asked (%02x %02x)\n",
                 __func__, pfl->cmd, cmd);
 #endif
         goto reset_flash;
     }
     DPRINTF("%s: offset " TARGET_FMT_plx " %08x %d %d\n", __func__,
             offset, value, width, pfl->wcycle);
     offset &= pfl->chip_len - 1;

     DPRINTF("%s: offset " TARGET_FMT_plx " %08x %d\n", __func__,
             offset, value, width);
     boff = offset & (pfl->sector_len - 1);
     if (pfl->width == 2)
         boff = boff >> 1;
     else if (pfl->width == 4)
         boff = boff >> 2;
     switch (pfl->wcycle) {
     case 0:
         /* Set the device in I/O access mode if required */
         if (pfl->rom_mode)
             pflash_register_memory(pfl, 0);
         /* We're in read mode */
     check_unlock0:
         if (boff == 0x55 && cmd == 0x98) {
         enter_CFI_mode:
             /* Enter CFI query mode */
             pfl->wcycle = 7;
             pfl->cmd = 0x98;
             return;
         }
         if (boff != pfl->unlock_addr[0] || cmd != 0xAA) {
             DPRINTF("%s: unlock0 failed " TARGET_FMT_plx " %02x %04x\n",
                     __func__, boff, cmd, pfl->unlock_addr[0]);
             goto reset_flash;
         }
         DPRINTF("%s: unlock sequence started\n", __func__);
         break;
     case 1:
         /* We started an unlock sequence */
     check_unlock1:
         if (boff != pfl->unlock_addr[1] || cmd != 0x55) {
             DPRINTF("%s: unlock1 failed " TARGET_FMT_plx " %02x\n", __func__,
                     boff, cmd);
             goto reset_flash;
         }
         DPRINTF("%s: unlock sequence done\n", __func__);
         break;
     case 2:
         /* We finished an unlock sequence */
         if (!pfl->bypass && boff != pfl->unlock_addr[0]) {
             DPRINTF("%s: command failed " TARGET_FMT_plx " %02x\n", __func__,
                     boff, cmd);
             goto reset_flash;
         }
         switch (cmd) {
         case 0x20:
             pfl->bypass = 1;
             goto do_bypass;
         case 0x80:
         case 0x90:
         case 0xA0:
             pfl->cmd = cmd;
             DPRINTF("%s: starting command %02x\n", __func__, cmd);
             break;
         default:
             DPRINTF("%s: unknown command %02x\n", __func__, cmd);
             goto reset_flash;
         }
         break;
     case 3:
         switch (pfl->cmd) {
         case 0x80:
             /* We need another unlock sequence */
             goto check_unlock0;
         case 0xA0:
             DPRINTF("%s: write data offset " TARGET_FMT_plx " %08x %d\n",
                     __func__, offset, value, width);
             p = pfl->storage;
             switch (width) {
             case 1:
                 p[offset] &= value;
                 pflash_update(pfl, offset, 1);
                 break;
             case 2:
                 if (be) {
                     p[offset] &= value >> 8;
                     p[offset + 1] &= value;
                 } else {
                     p[offset] &= value;
                     p[offset + 1] &= value >> 8;
                 }
                 pflash_update(pfl, offset, 2);
                 break;
             case 4:
                 if (be) {
                     p[offset] &= value >> 24;
                     p[offset + 1] &= value >> 16;
                     p[offset + 2] &= value >> 8;
                     p[offset + 3] &= value;
                 } else {
                     p[offset] &= value;
                     p[offset + 1] &= value >> 8;
                     p[offset + 2] &= value >> 16;
                     p[offset + 3] &= value >> 24;
                 }
                 pflash_update(pfl, offset, 4);
                 break;
             }
             pfl->status = 0x00 | ~(value & 0x80);
             /* Let's pretend write is immediate */
             if (pfl->bypass)
                 goto do_bypass;
             goto reset_flash;
         case 0x90:
             if (pfl->bypass && cmd == 0x00) {
                 /* Unlock bypass reset */
                 goto reset_flash;
             }
             /* We can enter CFI query mode from autoselect mode */
             if (boff == 0x55 && cmd == 0x98)
                 goto enter_CFI_mode;
             /* No break here */
         default:
             DPRINTF("%s: invalid write for command %02x\n",
                     __func__, pfl->cmd);
             goto reset_flash;
         }
     case 4:
         switch (pfl->cmd) {
         case 0xA0:
             /* Ignore writes while flash data write is occuring */
             /* As we suppose write is immediate, this should never happen */
             return;
         case 0x80:
             goto check_unlock1;
         default:
             /* Should never happen */
             DPRINTF("%s: invalid command state %02x (wc 4)\n",
                     __func__, pfl->cmd);
             goto reset_flash;
         }
         break;
     case 5:
         switch (cmd) {
         case 0x10:
             if (boff != pfl->unlock_addr[0]) {
                 DPRINTF("%s: chip erase: invalid address " TARGET_FMT_plx "\n",
                         __func__, offset);
                 goto reset_flash;
             }
             /* Chip erase */
             DPRINTF("%s: start chip erase\n", __func__);
             memset(pfl->storage, 0xFF, pfl->chip_len);
             pfl->status = 0x00;
             pflash_update(pfl, 0, pfl->chip_len);
             /* Let's wait 5 seconds before chip erase is done */
             qemu_mod_timer(pfl->timer,
                            qemu_get_clock(vm_clock) + (get_ticks_per_sec() * 5));
             break;
         case 0x30:
             /* Sector erase */
             p = pfl->storage;
             offset &= ~(pfl->sector_len - 1);
             DPRINTF("%s: start sector erase at " TARGET_FMT_plx "\n", __func__,
                     offset);
             memset(p + offset, 0xFF, pfl->sector_len);
             pflash_update(pfl, offset, pfl->sector_len);
             pfl->status = 0x00;
             /* Let's wait 1/2 second before sector erase is done */
             qemu_mod_timer(pfl->timer,
                            qemu_get_clock(vm_clock) + (get_ticks_per_sec() / 2));
             break;
         default:
             DPRINTF("%s: invalid command %02x (wc 5)\n", __func__, cmd);
             goto reset_flash;
         }
         pfl->cmd = cmd;
         break;
     case 6:
         switch (pfl->cmd) {
         case 0x10:
             /* Ignore writes during chip erase */
             return;
         case 0x30:
             /* Ignore writes during sector erase */
             return;
         default:
             /* Should never happen */
             DPRINTF("%s: invalid command state %02x (wc 6)\n",
                     __func__, pfl->cmd);
             goto reset_flash;
         }
         break;
     case 7: /* Special value for CFI queries */
         DPRINTF("%s: invalid write in CFI query mode\n", __func__);
         goto reset_flash;
     default:
         /* Should never happen */
         DPRINTF("%s: invalid write state (wc 7)\n",  __func__);
         goto reset_flash;
     }
     pfl->wcycle++;

     return;

     /* Reset flash */
  reset_flash:
     pfl->bypass = 0;
     pfl->wcycle = 0;
     pfl->cmd = 0;
     return;

  do_bypass:
     pfl->wcycle = 2;
     pfl->cmd = 0;
     return;
 }


 static uint32_t pflash_readb_be(void *opaque, target_phys_addr_t addr)
 {
     return pflash_read(opaque, addr, 1, 1);
 }

 static uint32_t pflash_readb_le(void *opaque, target_phys_addr_t addr)
 {
     return pflash_read(opaque, addr, 1, 0);
 }

 static uint32_t pflash_readw_be(void *opaque, target_phys_addr_t addr)
 {
     pflash_t *pfl = opaque;

     return pflash_read(pfl, addr, 2, 1);
 }

 static uint32_t pflash_readw_le(void *opaque, target_phys_addr_t addr)
 {
     pflash_t *pfl = opaque;

     return pflash_read(pfl, addr, 2, 0);
 }

 static uint32_t pflash_readl_be(void *opaque, target_phys_addr_t addr)
 {
     pflash_t *pfl = opaque;

     return pflash_read(pfl, addr, 4, 1);
 }

 static uint32_t pflash_readl_le(void *opaque, target_phys_addr_t addr)
 {
     pflash_t *pfl = opaque;

     return pflash_read(pfl, addr, 4, 0);
 }

 static void pflash_writeb_be(void *opaque, target_phys_addr_t addr,
                              uint32_t value)
 {
     pflash_write(opaque, addr, value, 1, 1);
 }

 static void pflash_writeb_le(void *opaque, target_phys_addr_t addr,
                              uint32_t value)
 {
     pflash_write(opaque, addr, value, 1, 0);
 }

 static void pflash_writew_be(void *opaque, target_phys_addr_t addr,
                              uint32_t value)
 {
     pflash_t *pfl = opaque;

     pflash_write(pfl, addr, value, 2, 1);
 }

 static void pflash_writew_le(void *opaque, target_phys_addr_t addr,
                              uint32_t value)
 {
     pflash_t *pfl = opaque;

     pflash_write(pfl, addr, value, 2, 0);
 }

 static void pflash_writel_be(void *opaque, target_phys_addr_t addr,
                              uint32_t value)
 {
     pflash_t *pfl = opaque;

     pflash_write(pfl, addr, value, 4, 1);
 }

 static void pflash_writel_le(void *opaque, target_phys_addr_t addr,
                              uint32_t value)
 {
     pflash_t *pfl = opaque;

     pflash_write(pfl, addr, value, 4, 0);
 }

 static CPUWriteMemoryFunc * const pflash_write_ops_be[] = {
     &pflash_writeb_be,
     &pflash_writew_be,
     &pflash_writel_be,
 };

 static CPUReadMemoryFunc * const pflash_read_ops_be[] = {
     &pflash_readb_be,
     &pflash_readw_be,
     &pflash_readl_be,
 };

 static CPUWriteMemoryFunc * const pflash_write_ops_le[] = {
     &pflash_writeb_le,
     &pflash_writew_le,
     &pflash_writel_le,
 };

 static CPUReadMemoryFunc * const pflash_read_ops_le[] = {
     &pflash_readb_le,
     &pflash_readw_le,
     &pflash_readl_le,
 };

 /* Count trailing zeroes of a 32 bits quantity */
 static int ctz32 (uint32_t n)
 {
     int ret;

     ret = 0;
     if (!(n & 0xFFFF)) {
         ret += 16;
         n = n >> 16;
     }
     if (!(n & 0xFF)) {
         ret += 8;
         n = n >> 8;
     }
     if (!(n & 0xF)) {
         ret += 4;
         n = n >> 4;
     }
     if (!(n & 0x3)) {
         ret += 2;
         n = n >> 2;
     }
     if (!(n & 0x1)) {
         ret++;
 #if 0 /* This is not necessary as n is never 0 */
         n = n >> 1;
 #endif
     }
 #if 0 /* This is not necessary as n is never 0 */
     if (!n)
         ret++;
 #endif

     return ret;
 }

 pflash_t *pflash_cfi02_register(target_phys_addr_t base, ram_addr_t off,
                                 BlockDriverState *bs, uint32_t sector_len,
                                 int nb_blocs, int nb_mappings, int width,
                                 uint16_t id0, uint16_t id1,
                                 uint16_t id2, uint16_t id3,
                                 uint16_t unlock_addr0, uint16_t unlock_addr1,
                                 int be)
 {
     pflash_t *pfl;
     int32_t chip_len;
     int ret;

     chip_len = sector_len * nb_blocs;
     /* XXX: to be fixed */
 #if 0
     if (total_len != (8 * 1024 * 1024) && total_len != (16 * 1024 * 1024) &&
         total_len != (32 * 1024 * 1024) && total_len != (64 * 1024 * 1024))
         return NULL;
 #endif
     pfl = qemu_mallocz(sizeof(pflash_t));
     /* FIXME: Allocate ram ourselves.  */
     pfl->storage = qemu_get_ram_ptr(off);
     if (be) {
         pfl->fl_mem = cpu_register_io_memory(pflash_read_ops_be,
                                              pflash_write_ops_be,
                                              pfl);
     } else {
         pfl->fl_mem = cpu_register_io_memory(pflash_read_ops_le,
                                              pflash_write_ops_le,
                                              pfl);
     }
     pfl->off = off;
     pfl->base = base;
     pfl->chip_len = chip_len;
     pfl->mappings = nb_mappings;
     pflash_register_memory(pfl, 1);
     pfl->bs = bs;
     if (pfl->bs) {
         /* read the initial flash content */
         ret = bdrv_read(pfl->bs, 0, pfl->storage, chip_len >> 9);
         if (ret < 0) {
             cpu_unregister_io_memory(pfl->fl_mem);
             qemu_free(pfl);
             return NULL;
         }
     }
 #if 0 /* XXX: there should be a bit to set up read-only,
        *      the same way the hardware does (with WP pin).
        */
     pfl->ro = 1;
 #else
     pfl->ro = 0;
 #endif
     pfl->timer = qemu_new_timer(vm_clock, pflash_timer, pfl);
     pfl->sector_len = sector_len;
     pfl->width = width;
     pfl->wcycle = 0;
     pfl->cmd = 0;
     pfl->status = 0;
     pfl->ident[0] = id0;
     pfl->ident[1] = id1;
     pfl->ident[2] = id2;
     pfl->ident[3] = id3;
     pfl->unlock_addr[0] = unlock_addr0;
     pfl->unlock_addr[1] = unlock_addr1;
     /* Hardcoded CFI table (mostly from SG29 Spansion flash) */
     pfl->cfi_len = 0x52;
     /* Standard "QRY" string */
     pfl->cfi_table[0x10] = 'Q';
     pfl->cfi_table[0x11] = 'R';
     pfl->cfi_table[0x12] = 'Y';
     /* Command set (AMD/Fujitsu) */
     pfl->cfi_table[0x13] = 0x02;
     pfl->cfi_table[0x14] = 0x00;
     /* Primary extended table address */
     pfl->cfi_table[0x15] = 0x31;
     pfl->cfi_table[0x16] = 0x00;
     /* Alternate command set (none) */
     pfl->cfi_table[0x17] = 0x00;
     pfl->cfi_table[0x18] = 0x00;
     /* Alternate extended table (none) */
     pfl->cfi_table[0x19] = 0x00;
     pfl->cfi_table[0x1A] = 0x00;
     /* Vcc min */
     pfl->cfi_table[0x1B] = 0x27;
     /* Vcc max */
     pfl->cfi_table[0x1C] = 0x36;
     /* Vpp min (no Vpp pin) */
     pfl->cfi_table[0x1D] = 0x00;
     /* Vpp max (no Vpp pin) */
     pfl->cfi_table[0x1E] = 0x00;
     /* Reserved */
     pfl->cfi_table[0x1F] = 0x07;
     /* Timeout for min size buffer write (NA) */
     pfl->cfi_table[0x20] = 0x00;
     /* Typical timeout for block erase (512 ms) */
     pfl->cfi_table[0x21] = 0x09;
     /* Typical timeout for full chip erase (4096 ms) */
     pfl->cfi_table[0x22] = 0x0C;
     /* Reserved */
     pfl->cfi_table[0x23] = 0x01;
     /* Max timeout for buffer write (NA) */
     pfl->cfi_table[0x24] = 0x00;
     /* Max timeout for block erase */
     pfl->cfi_table[0x25] = 0x0A;
     /* Max timeout for chip erase */
     pfl->cfi_table[0x26] = 0x0D;
     /* Device size */
     pfl->cfi_table[0x27] = ctz32(chip_len);
     /* Flash device interface (8 & 16 bits) */
     pfl->cfi_table[0x28] = 0x02;
     pfl->cfi_table[0x29] = 0x00;
     /* Max number of bytes in multi-bytes write */
     /* XXX: disable buffered write as it's not supported */
     //    pfl->cfi_table[0x2A] = 0x05;
     pfl->cfi_table[0x2A] = 0x00;
     pfl->cfi_table[0x2B] = 0x00;
     /* Number of erase block regions (uniform) */
     pfl->cfi_table[0x2C] = 0x01;
     /* Erase block region 1 */
     pfl->cfi_table[0x2D] = nb_blocs - 1;
     pfl->cfi_table[0x2E] = (nb_blocs - 1) >> 8;
     pfl->cfi_table[0x2F] = sector_len >> 8;
     pfl->cfi_table[0x30] = sector_len >> 16;

     /* Extended */
     pfl->cfi_table[0x31] = 'P';
     pfl->cfi_table[0x32] = 'R';
     pfl->cfi_table[0x33] = 'I';

     pfl->cfi_table[0x34] = '1';
     pfl->cfi_table[0x35] = '0';

     pfl->cfi_table[0x36] = 0x00;
     pfl->cfi_table[0x37] = 0x00;
     pfl->cfi_table[0x38] = 0x00;
     pfl->cfi_table[0x39] = 0x00;

     pfl->cfi_table[0x3a] = 0x00;

     pfl->cfi_table[0x3b] = 0x00;
     pfl->cfi_table[0x3c] = 0x00;

     return pfl;
 }
	/*
	* CFI parallel flash with AMD command set emulation
	*
	* Copyright (c) 2005 Jocelyn Mayer
	*
	* This library is free software; you can redistribute it and/or
	* modify it under the terms of the GNU Lesser General Public
	* License as published by the Free Software Foundation; either
	* version 2 of the License, or (at your option) any later version.
	*
	* This library is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
	* Lesser General Public License for more details.
	*
	* You should have received a copy of the GNU Lesser General Public
	* License along with this library; if not, see <http://www.gnu.org/licenses/>.
	*/

	/*
	* For now, this code can emulate flashes of 1, 2 or 4 bytes width.
	* Supported commands/modes are:
	* - flash read
	* - flash write
	* - flash ID read
	* - sector erase
	* - chip erase
	* - unlock bypass command
	* - CFI queries
	*
	* It does not support flash interleaving.
	* It does not implement boot blocs with reduced size
	* It does not implement software data protection as found in many real chips
	* It does not implement erase suspend/resume commands
	* It does not implement multiple sectors erase
	*/

	#include "hw.h"
	#include "flash.h"
	#include "qemu-timer.h"
	#include "block.h"

	//#define PFLASH_DEBUG
	#ifdef PFLASH_DEBUG
	#define DPRINTF(fmt, ...) \
	do { \
	printf("PFLASH: " fmt , ## __VA_ARGS__); \
	} while (0)
	#else
	#define DPRINTF(fmt, ...) do { } while (0)
	#endif

	struct pflash_t {
	BlockDriverState *bs;
	target_phys_addr_t base;
	uint32_t sector_len;
	uint32_t chip_len;
	int mappings;
	int width;
	int wcycle; /* if 0, the flash is read normally */
	int bypass;
	int ro;
	uint8_t cmd;
	uint8_t status;
	uint16_t ident[4];
	uint16_t unlock_addr[2];
	uint8_t cfi_len;
	uint8_t cfi_table[0x52];
	QEMUTimer *timer;
	ram_addr_t off;
	int fl_mem;
	int rom_mode;
	void *storage;
	};

	static void pflash_register_memory(pflash_t *pfl, int rom_mode)
	{
	unsigned long phys_offset = pfl->fl_mem;
	int i;

	if (rom_mode)
	phys_offset \|= pfl->off \| IO_MEM_ROMD;
	pfl->rom_mode = rom_mode;

	for (i = 0; i < pfl->mappings; i++)
	cpu_register_physical_memory(pfl->base + i * pfl->chip_len,
	pfl->chip_len, phys_offset);
	}

	static void pflash_timer (void *opaque)
	{
	pflash_t *pfl = opaque;

	DPRINTF("%s: command %02x done\n", __func__, pfl->cmd);
	/* Reset flash */
	pfl->status ^= 0x80;
	if (pfl->bypass) {
	pfl->wcycle = 2;
	} else {
	pflash_register_memory(pfl, 1);
	pfl->wcycle = 0;
	}
	pfl->cmd = 0;
	}

	static uint32_t pflash_read (pflash_t *pfl, target_phys_addr_t offset,
	int width, int be)
	{
	target_phys_addr_t boff;
	uint32_t ret;
	uint8_t *p;

	DPRINTF("%s: offset " TARGET_FMT_plx "\n", __func__, offset);
	ret = -1;
	if (pfl->rom_mode) {
	/* Lazy reset of to ROMD mode */
	if (pfl->wcycle == 0)
	pflash_register_memory(pfl, 1);
	}
	offset &= pfl->chip_len - 1;
	boff = offset & 0xFF;
	if (pfl->width == 2)
	boff = boff >> 1;
	else if (pfl->width == 4)
	boff = boff >> 2;
	switch (pfl->cmd) {
	default:
	/* This should never happen : reset state & treat it as a read*/
	DPRINTF("%s: unknown command state: %x\n", __func__, pfl->cmd);
	pfl->wcycle = 0;
	pfl->cmd = 0;
	case 0x80:
	/* We accept reads during second unlock sequence... */
	case 0x00:
	flash_read:
	/* Flash area read */
	p = pfl->storage;
	switch (width) {
	case 1:
	ret = p[offset];
	// DPRINTF("%s: data offset %08x %02x\n", __func__, offset, ret);
	break;
	case 2:
	if (be) {
	ret = p[offset] << 8;
	ret \|= p[offset + 1];
	} else {
	ret = p[offset];
	ret \|= p[offset + 1] << 8;
	}
	// DPRINTF("%s: data offset %08x %04x\n", __func__, offset, ret);
	break;
	case 4:
	if (be) {
	ret = p[offset] << 24;
	ret \|= p[offset + 1] << 16;
	ret \|= p[offset + 2] << 8;
	ret \|= p[offset + 3];
	} else {
	ret = p[offset];
	ret \|= p[offset + 1] << 8;
	ret \|= p[offset + 2] << 16;
	ret \|= p[offset + 3] << 24;
	}
	// DPRINTF("%s: data offset %08x %08x\n", __func__, offset, ret);
	break;
	}
	break;
	case 0x90:
	/* flash ID read */
	switch (boff) {
	case 0x00:
	case 0x01:
	ret = pfl->ident[boff & 0x01];
	break;
	case 0x02:
	ret = 0x00; /* Pretend all sectors are unprotected */
	break;
	case 0x0E:
	case 0x0F:
	if (pfl->ident[2 + (boff & 0x01)] == (uint8_t)-1)
	goto flash_read;
	ret = pfl->ident[2 + (boff & 0x01)];
	break;
	default:
	goto flash_read;
	}
	DPRINTF("%s: ID " TARGET_FMT_pld " %x\n", __func__, boff, ret);
	break;
	case 0xA0:
	case 0x10:
	case 0x30:
	/* Status register read */
	ret = pfl->status;
	DPRINTF("%s: status %x\n", __func__, ret);
	/* Toggle bit 6 */
	pfl->status ^= 0x40;
	break;
	case 0x98:
	/* CFI query mode */
	if (boff > pfl->cfi_len)
	ret = 0;
	else
	ret = pfl->cfi_table[boff];
	break;
	}

	return ret;
	}

	/* update flash content on disk */
	static void pflash_update(pflash_t *pfl, int offset,
	int size)
	{
	int offset_end;
	if (pfl->bs) {
	offset_end = offset + size;
	/* round to sectors */
	offset = offset >> 9;
	offset_end = (offset_end + 511) >> 9;
	bdrv_write(pfl->bs, offset, pfl->storage + (offset << 9),
	offset_end - offset);
	}
	}

	static void pflash_write (pflash_t *pfl, target_phys_addr_t offset,
	uint32_t value, int width, int be)
	{
	target_phys_addr_t boff;
	uint8_t *p;
	uint8_t cmd;

	cmd = value;
	if (pfl->cmd != 0xA0 && cmd == 0xF0) {
	#if 0
	DPRINTF("%s: flash reset asked (%02x %02x)\n",
	__func__, pfl->cmd, cmd);
	#endif
	goto reset_flash;
	}
	DPRINTF("%s: offset " TARGET_FMT_plx " %08x %d %d\n", __func__,
	offset, value, width, pfl->wcycle);
	offset &= pfl->chip_len - 1;

	DPRINTF("%s: offset " TARGET_FMT_plx " %08x %d\n", __func__,
	offset, value, width);
	boff = offset & (pfl->sector_len - 1);
	if (pfl->width == 2)
	boff = boff >> 1;
	else if (pfl->width == 4)
	boff = boff >> 2;
	switch (pfl->wcycle) {
	case 0:
	/* Set the device in I/O access mode if required */
	if (pfl->rom_mode)
	pflash_register_memory(pfl, 0);
	/* We're in read mode */
	check_unlock0:
	if (boff == 0x55 && cmd == 0x98) {
	enter_CFI_mode:
	/* Enter CFI query mode */
	pfl->wcycle = 7;
	pfl->cmd = 0x98;
	return;
	}
	if (boff != pfl->unlock_addr[0] \|\| cmd != 0xAA) {
	DPRINTF("%s: unlock0 failed " TARGET_FMT_plx " %02x %04x\n",
	__func__, boff, cmd, pfl->unlock_addr[0]);
	goto reset_flash;
	}
	DPRINTF("%s: unlock sequence started\n", __func__);
	break;
	case 1:
	/* We started an unlock sequence */
	check_unlock1:
	if (boff != pfl->unlock_addr[1] \|\| cmd != 0x55) {
	DPRINTF("%s: unlock1 failed " TARGET_FMT_plx " %02x\n", __func__,
	boff, cmd);
	goto reset_flash;
	}
	DPRINTF("%s: unlock sequence done\n", __func__);
	break;
	case 2:
	/* We finished an unlock sequence */
	if (!pfl->bypass && boff != pfl->unlock_addr[0]) {
	DPRINTF("%s: command failed " TARGET_FMT_plx " %02x\n", __func__,
	boff, cmd);
	goto reset_flash;
	}
	switch (cmd) {
	case 0x20:
	pfl->bypass = 1;
	goto do_bypass;
	case 0x80:
	case 0x90:
	case 0xA0:
	pfl->cmd = cmd;
	DPRINTF("%s: starting command %02x\n", __func__, cmd);
	break;
	default:
	DPRINTF("%s: unknown command %02x\n", __func__, cmd);
	goto reset_flash;
	}
	break;
	case 3:
	switch (pfl->cmd) {
	case 0x80:
	/* We need another unlock sequence */
	goto check_unlock0;
	case 0xA0:
	DPRINTF("%s: write data offset " TARGET_FMT_plx " %08x %d\n",
	__func__, offset, value, width);
	p = pfl->storage;
	switch (width) {
	case 1:
	p[offset] &= value;
	pflash_update(pfl, offset, 1);
	break;
	case 2:
	if (be) {
	p[offset] &= value >> 8;
	p[offset + 1] &= value;
	} else {
	p[offset] &= value;
	p[offset + 1] &= value >> 8;
	}
	pflash_update(pfl, offset, 2);
	break;
	case 4:
	if (be) {
	p[offset] &= value >> 24;
	p[offset + 1] &= value >> 16;
	p[offset + 2] &= value >> 8;
	p[offset + 3] &= value;
	} else {
	p[offset] &= value;
	p[offset + 1] &= value >> 8;
	p[offset + 2] &= value >> 16;
	p[offset + 3] &= value >> 24;
	}
	pflash_update(pfl, offset, 4);
	break;
	}
	pfl->status = 0x00 \| ~(value & 0x80);
	/* Let's pretend write is immediate */
	if (pfl->bypass)
	goto do_bypass;
	goto reset_flash;
	case 0x90:
	if (pfl->bypass && cmd == 0x00) {
	/* Unlock bypass reset */
	goto reset_flash;
	}
	/* We can enter CFI query mode from autoselect mode */
	if (boff == 0x55 && cmd == 0x98)
	goto enter_CFI_mode;
	/* No break here */
	default:
	DPRINTF("%s: invalid write for command %02x\n",
	__func__, pfl->cmd);
	goto reset_flash;
	}
	case 4:
	switch (pfl->cmd) {
	case 0xA0:
	/* Ignore writes while flash data write is occuring */
	/* As we suppose write is immediate, this should never happen */
	return;
	case 0x80:
	goto check_unlock1;
	default:
	/* Should never happen */
	DPRINTF("%s: invalid command state %02x (wc 4)\n",
	__func__, pfl->cmd);
	goto reset_flash;
	}
	break;
	case 5:
	switch (cmd) {
	case 0x10:
	if (boff != pfl->unlock_addr[0]) {
	DPRINTF("%s: chip erase: invalid address " TARGET_FMT_plx "\n",
	__func__, offset);
	goto reset_flash;
	}
	/* Chip erase */
	DPRINTF("%s: start chip erase\n", __func__);
	memset(pfl->storage, 0xFF, pfl->chip_len);
	pfl->status = 0x00;
	pflash_update(pfl, 0, pfl->chip_len);
	/* Let's wait 5 seconds before chip erase is done */
	qemu_mod_timer(pfl->timer,
	qemu_get_clock(vm_clock) + (get_ticks_per_sec() * 5));
	break;
	case 0x30:
	/* Sector erase */
	p = pfl->storage;
	offset &= ~(pfl->sector_len - 1);
	DPRINTF("%s: start sector erase at " TARGET_FMT_plx "\n", __func__,
	offset);
	memset(p + offset, 0xFF, pfl->sector_len);
	pflash_update(pfl, offset, pfl->sector_len);
	pfl->status = 0x00;
	/* Let's wait 1/2 second before sector erase is done */
	qemu_mod_timer(pfl->timer,
	qemu_get_clock(vm_clock) + (get_ticks_per_sec() / 2));
	break;
	default:
	DPRINTF("%s: invalid command %02x (wc 5)\n", __func__, cmd);
	goto reset_flash;
	}
	pfl->cmd = cmd;
	break;
	case 6:
	switch (pfl->cmd) {
	case 0x10:
	/* Ignore writes during chip erase */
	return;
	case 0x30:
	/* Ignore writes during sector erase */
	return;
	default:
	/* Should never happen */
	DPRINTF("%s: invalid command state %02x (wc 6)\n",
	__func__, pfl->cmd);
	goto reset_flash;
	}
	break;
	case 7: /* Special value for CFI queries */
	DPRINTF("%s: invalid write in CFI query mode\n", __func__);
	goto reset_flash;
	default:
	/* Should never happen */
	DPRINTF("%s: invalid write state (wc 7)\n", __func__);
	goto reset_flash;
	}
	pfl->wcycle++;

	return;

	/* Reset flash */
	reset_flash:
	pfl->bypass = 0;
	pfl->wcycle = 0;
	pfl->cmd = 0;
	return;

	do_bypass:
	pfl->wcycle = 2;
	pfl->cmd = 0;
	return;
	}


	static uint32_t pflash_readb_be(void *opaque, target_phys_addr_t addr)
	{
	return pflash_read(opaque, addr, 1, 1);
	}

	static uint32_t pflash_readb_le(void *opaque, target_phys_addr_t addr)
	{
	return pflash_read(opaque, addr, 1, 0);
	}

	static uint32_t pflash_readw_be(void *opaque, target_phys_addr_t addr)
	{
	pflash_t *pfl = opaque;

	return pflash_read(pfl, addr, 2, 1);
	}

	static uint32_t pflash_readw_le(void *opaque, target_phys_addr_t addr)
	{
	pflash_t *pfl = opaque;

	return pflash_read(pfl, addr, 2, 0);
	}

	static uint32_t pflash_readl_be(void *opaque, target_phys_addr_t addr)
	{
	pflash_t *pfl = opaque;

	return pflash_read(pfl, addr, 4, 1);
	}

	static uint32_t pflash_readl_le(void *opaque, target_phys_addr_t addr)
	{
	pflash_t *pfl = opaque;

	return pflash_read(pfl, addr, 4, 0);
	}

	static void pflash_writeb_be(void *opaque, target_phys_addr_t addr,
	uint32_t value)
	{
	pflash_write(opaque, addr, value, 1, 1);
	}

	static void pflash_writeb_le(void *opaque, target_phys_addr_t addr,
	uint32_t value)
	{
	pflash_write(opaque, addr, value, 1, 0);
	}

	static void pflash_writew_be(void *opaque, target_phys_addr_t addr,
	uint32_t value)
	{
	pflash_t *pfl = opaque;

	pflash_write(pfl, addr, value, 2, 1);
	}

	static void pflash_writew_le(void *opaque, target_phys_addr_t addr,
	uint32_t value)
	{
	pflash_t *pfl = opaque;

	pflash_write(pfl, addr, value, 2, 0);
	}

	static void pflash_writel_be(void *opaque, target_phys_addr_t addr,
	uint32_t value)
	{
	pflash_t *pfl = opaque;

	pflash_write(pfl, addr, value, 4, 1);
	}

	static void pflash_writel_le(void *opaque, target_phys_addr_t addr,
	uint32_t value)
	{
	pflash_t *pfl = opaque;

	pflash_write(pfl, addr, value, 4, 0);
	}

	static CPUWriteMemoryFunc * const pflash_write_ops_be[] = {
	&pflash_writeb_be,
	&pflash_writew_be,
	&pflash_writel_be,
	};

	static CPUReadMemoryFunc * const pflash_read_ops_be[] = {
	&pflash_readb_be,
	&pflash_readw_be,
	&pflash_readl_be,
	};

	static CPUWriteMemoryFunc * const pflash_write_ops_le[] = {
	&pflash_writeb_le,
	&pflash_writew_le,
	&pflash_writel_le,
	};

	static CPUReadMemoryFunc * const pflash_read_ops_le[] = {
	&pflash_readb_le,
	&pflash_readw_le,
	&pflash_readl_le,
	};

	/* Count trailing zeroes of a 32 bits quantity */
	static int ctz32 (uint32_t n)
	{
	int ret;

	ret = 0;
	if (!(n & 0xFFFF)) {
	ret += 16;
	n = n >> 16;
	}
	if (!(n & 0xFF)) {
	ret += 8;
	n = n >> 8;
	}
	if (!(n & 0xF)) {
	ret += 4;
	n = n >> 4;
	}
	if (!(n & 0x3)) {
	ret += 2;
	n = n >> 2;
	}
	if (!(n & 0x1)) {
	ret++;
	#if 0 /* This is not necessary as n is never 0 */
	n = n >> 1;
	#endif
	}
	#if 0 /* This is not necessary as n is never 0 */
	if (!n)
	ret++;
	#endif

	return ret;
	}

	pflash_t *pflash_cfi02_register(target_phys_addr_t base, ram_addr_t off,
	BlockDriverState *bs, uint32_t sector_len,
	int nb_blocs, int nb_mappings, int width,
	uint16_t id0, uint16_t id1,
	uint16_t id2, uint16_t id3,
	uint16_t unlock_addr0, uint16_t unlock_addr1,
	int be)
	{
	pflash_t *pfl;
	int32_t chip_len;
	int ret;

	chip_len = sector_len * nb_blocs;
	/* XXX: to be fixed */
	#if 0
	if (total_len != (8 * 1024 * 1024) && total_len != (16 * 1024 * 1024) &&
	total_len != (32 * 1024 * 1024) && total_len != (64 * 1024 * 1024))
	return NULL;
	#endif
	pfl = qemu_mallocz(sizeof(pflash_t));
	/* FIXME: Allocate ram ourselves. */
	pfl->storage = qemu_get_ram_ptr(off);
	if (be) {
	pfl->fl_mem = cpu_register_io_memory(pflash_read_ops_be,
	pflash_write_ops_be,
	pfl);
	} else {
	pfl->fl_mem = cpu_register_io_memory(pflash_read_ops_le,
	pflash_write_ops_le,
	pfl);
	}
	pfl->off = off;
	pfl->base = base;
	pfl->chip_len = chip_len;
	pfl->mappings = nb_mappings;
	pflash_register_memory(pfl, 1);
	pfl->bs = bs;
	if (pfl->bs) {
	/* read the initial flash content */
	ret = bdrv_read(pfl->bs, 0, pfl->storage, chip_len >> 9);
	if (ret < 0) {
	cpu_unregister_io_memory(pfl->fl_mem);
	qemu_free(pfl);
	return NULL;
	}
	}
	#if 0 /* XXX: there should be a bit to set up read-only,
	* the same way the hardware does (with WP pin).
	*/
	pfl->ro = 1;
	#else
	pfl->ro = 0;
	#endif
	pfl->timer = qemu_new_timer(vm_clock, pflash_timer, pfl);
	pfl->sector_len = sector_len;
	pfl->width = width;
	pfl->wcycle = 0;
	pfl->cmd = 0;
	pfl->status = 0;
	pfl->ident[0] = id0;
	pfl->ident[1] = id1;
	pfl->ident[2] = id2;
	pfl->ident[3] = id3;
	pfl->unlock_addr[0] = unlock_addr0;
	pfl->unlock_addr[1] = unlock_addr1;
	/* Hardcoded CFI table (mostly from SG29 Spansion flash) */
	pfl->cfi_len = 0x52;
	/* Standard "QRY" string */
	pfl->cfi_table[0x10] = 'Q';
	pfl->cfi_table[0x11] = 'R';
	pfl->cfi_table[0x12] = 'Y';
	/* Command set (AMD/Fujitsu) */
	pfl->cfi_table[0x13] = 0x02;
	pfl->cfi_table[0x14] = 0x00;
	/* Primary extended table address */
	pfl->cfi_table[0x15] = 0x31;
	pfl->cfi_table[0x16] = 0x00;
	/* Alternate command set (none) */
	pfl->cfi_table[0x17] = 0x00;
	pfl->cfi_table[0x18] = 0x00;
	/* Alternate extended table (none) */
	pfl->cfi_table[0x19] = 0x00;
	pfl->cfi_table[0x1A] = 0x00;
	/* Vcc min */
	pfl->cfi_table[0x1B] = 0x27;
	/* Vcc max */
	pfl->cfi_table[0x1C] = 0x36;
	/* Vpp min (no Vpp pin) */
	pfl->cfi_table[0x1D] = 0x00;
	/* Vpp max (no Vpp pin) */
	pfl->cfi_table[0x1E] = 0x00;
	/* Reserved */
	pfl->cfi_table[0x1F] = 0x07;
	/* Timeout for min size buffer write (NA) */
	pfl->cfi_table[0x20] = 0x00;
	/* Typical timeout for block erase (512 ms) */
	pfl->cfi_table[0x21] = 0x09;
	/* Typical timeout for full chip erase (4096 ms) */
	pfl->cfi_table[0x22] = 0x0C;
	/* Reserved */
	pfl->cfi_table[0x23] = 0x01;
	/* Max timeout for buffer write (NA) */
	pfl->cfi_table[0x24] = 0x00;
	/* Max timeout for block erase */
	pfl->cfi_table[0x25] = 0x0A;
	/* Max timeout for chip erase */
	pfl->cfi_table[0x26] = 0x0D;
	/* Device size */
	pfl->cfi_table[0x27] = ctz32(chip_len);
	/* Flash device interface (8 & 16 bits) */
	pfl->cfi_table[0x28] = 0x02;
	pfl->cfi_table[0x29] = 0x00;
	/* Max number of bytes in multi-bytes write */
	/* XXX: disable buffered write as it's not supported */
	// pfl->cfi_table[0x2A] = 0x05;
	pfl->cfi_table[0x2A] = 0x00;
	pfl->cfi_table[0x2B] = 0x00;
	/* Number of erase block regions (uniform) */
	pfl->cfi_table[0x2C] = 0x01;
	/* Erase block region 1 */
	pfl->cfi_table[0x2D] = nb_blocs - 1;
	pfl->cfi_table[0x2E] = (nb_blocs - 1) >> 8;
	pfl->cfi_table[0x2F] = sector_len >> 8;
	pfl->cfi_table[0x30] = sector_len >> 16;

	/* Extended */
	pfl->cfi_table[0x31] = 'P';
	pfl->cfi_table[0x32] = 'R';
	pfl->cfi_table[0x33] = 'I';

	pfl->cfi_table[0x34] = '1';
	pfl->cfi_table[0x35] = '0';

	pfl->cfi_table[0x36] = 0x00;
	pfl->cfi_table[0x37] = 0x00;
	pfl->cfi_table[0x38] = 0x00;
	pfl->cfi_table[0x39] = 0x00;

	pfl->cfi_table[0x3a] = 0x00;

	pfl->cfi_table[0x3b] = 0x00;
	pfl->cfi_table[0x3c] = 0x00;

	return pfl;
	}