tree 5d64cbae06de7f3cc569bee32d7365d7b5183da0
parent 4dd5f7b8d568116b3ce594b0055a47c6db50f49c
author Peter Xu <peterx@redhat.com> 1718836240 -0400
committer Fabiano Rosas <farosas@suse.de> 1718974079 -0300

migration/postcopy: Add postcopy-recover-setup phase

This patch adds a migration state on src called "postcopy-recover-setup".
The new state will describe the intermediate step starting from when the
src QEMU received a postcopy recovery request, until the migration channels
are properly established, but before the recovery process take place.

The request came from Libvirt where Libvirt currently rely on the migration
state events to detect migration state changes.  That works for most of the
migration process but except postcopy recovery failures at the beginning.

Currently postcopy recovery only has two major states:

  - postcopy-paused: this is the state that both sides of QEMU will be in
    for a long time as long as the migration channel was interrupted.

  - postcopy-recover: this is the state where both sides of QEMU handshake
    with each other, preparing for a continuation of postcopy which used to
    be interrupted.

The issue here is when the recovery port is invalid, the src QEMU will take
the URI/channels, noticing the ports are not valid, and it'll silently keep
in the postcopy-paused state, with no event sent to Libvirt.  In this case,
the only thing Libvirt can do is to poll the migration status with a proper
interval, however that's less optimal.

Considering that this is the only case where Libvirt won't get a
notification from QEMU on such events, let's add postcopy-recover-setup
state to mimic what we have with the "setup" state of a newly initialized
migration, describing the phase of connection establishment.

With that, postcopy recovery will have two paths to go now, and either path
will guarantee an event generated.  Now the events will look like this
during a recovery process on src QEMU:

  - Initially when the recovery is initiated on src, QEMU will go from
    "postcopy-paused" -> "postcopy-recover-setup".  Old QEMUs don't have
    this event.

  - Depending on whether the channel re-establishment is succeeded:

    - In succeeded case, src QEMU will move from "postcopy-recover-setup"
      to "postcopy-recover".  Old QEMUs also have this event.

    - In failure case, src QEMU will move from "postcopy-recover-setup" to
      "postcopy-paused" again.  Old QEMUs don't have this event.

This guarantees that Libvirt will always receive a notification for
recovery process properly.

One thing to mention is, such new status is only needed on src QEMU not
both.  On dest QEMU, the state machine doesn't change.  Hence the events
don't change either.  It's done like so because dest QEMU may not have an
explicit point of setup start.  E.g., it can happen that when dest QEMUs
doesn't use migrate-recover command to use a new URI/channel, but the old
URI/channels can be reused in recovery, in which case the old ports simply
can work again after the network routes are fixed up.

Add a new helper postcopy_is_paused() detecting whether postcopy is still
paused, taking RECOVER_SETUP into account too.  When using it on both
src/dst, a slight change is done altogether to always wait for the
semaphore before checking the status, because for both sides a sem_post()
will be required for a recovery.

Cc: Jiri Denemark <jdenemar@redhat.com>
Cc: Prasad Pandit <ppandit@redhat.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Buglink: https://issues.redhat.com/browse/RHEL-38485
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Fabiano Rosas <farosas@suse.de>